- 26 Nov, 2023 3 commits
-
-
Su Hui authored
regmap_bulk_write()/regmap_bulk_read() return zero or negative error code, return the callee's error code is better than '-EINVAL'. Signed-off-by:
Su Hui <suhui@nfschina.com> Link: https://lore.kernel.org/r/20231030020752.67630-1-suhui@nfschina.comSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Ana-Maria Cusco authored
This adds support for the Analog Devices ADRF5740 2 dB LSB, 4-Bit, Silicon Digital Attenuator, 10 MHz to 60 GHz. The default (maximum) gain is also set at probe time, with GPIO lines driven high to achieve maximum gain, in contrast to other devices where GPIOs need to be driven low. Signed-off-by:
Ana-Maria Cusco <ana-maria.cusco@analog.com> Link: https://lore.kernel.org/r/20231113102535.51074-2-anamaria.cuscoo@gmail.comSigned-off-by:
-
Ana-Maria Cusco authored
The ADRF5740 is a silicon, 4-bit digital attenuator with 22 dB attenuation control range in 2 dB steps. Signed-off-by:
Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20231113102535.51074-3-anamaria.cuscoo@gmail.comSigned-off-by:
-
- 25 Nov, 2023 1 commit
-
-
Lukas Bulwahn authored
Commit 33ec3e5f ("iio: adc: adding support for MCP3564 ADC") adds a new iio driver and corresponding MAINTAINERS section. It however uses spaces instead of a single tab for all the entries in that MAINTAINERS section. Although, the get_maintainer.pl script handles spaces instead of tabs silently, the MAINTAINERS will quickly get into a messy state with different indentations throughout the file. So, the checkpatch.pl script complains when spaces instead of a single tab are used. Fix this recently added section using tabs instead of spaces. Further, add the driver's ABI documentation file to this section as well. Fixes: 33ec3e5f ("iio: adc: adding support for MCP3564 ADC") Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20231122075629.21411-1-lukas.bulwahn@gmail.comSigned-off-by:
-
- 16 Nov, 2023 31 commits
-
-
Matti Vaittinen authored
Add documentation explaining why the code which scans all available scan masks is checking only a single long worth of bits even though the code was intended to be supporting masks wider than single long. Signed-off-by:
Matti Vaittinen <mazziesaccount@gmail.com> Link: https://lore.kernel.org/r/ef61c2c1e9a1c5e9f713f656871fdcb1652afdc2.1697452986.git.mazziesaccount@gmail.comSigned-off-by:
-
Matti Vaittinen authored
When IIO goes through the available scan masks in order to select the best suiting one, it will just accept the first listed subset of channels which meets the user's requirements. If driver lists a mask which is a subset of some of the masks previously in the array of avaliable_scan_masks, then the latter one will never be selected. Add a warning if driver registers masks which can't be used due to the available_scan_masks-array ordering. Suggested-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Ramona Gradinariu authored
The adis16460 device requires a stall time between SPI transactions (during which the chip select is inactive), with a minimum value equal to 16 microseconds. This commit adds 'spi-cs-inactive-delay-ns' property, which should indicate the stall time between consecutive SPI transactions. The specified minimum time may not be sufficient for all configurations. Signed-off-by:
Ramona Gradinariu <ramona.gradinariu@analog.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20231027140358.328699-4-ramona.gradinariu@analog.comSigned-off-by:
-
Ramona Gradinariu authored
The devices supported by adis16475 driver require a stall period between SPI transactions (during which the chip select is inactive), with a minimum value equal to 16 microseconds, thus adding 'spi-cs-inactive-delay-ns' property, which should indicate the stall time between consecutive SPI transactions. The specified minimum time may not be sufficient for all configurations. Signed-off-by:
-
Ramona Gradinariu authored
A delay is needed each time the chip selected becomes inactive, even after burst data readings are performed. Currently, there is no delay added after a burst reading and in case a new SPI transfer is performed before the needed delay, the adis device becomes unresponsive until reset. This commit is adding the needed delay directly to the spi driver, using the cs_inactive parameter, in case it is not set and is removing the additional chip select change delay present in adis APIs to remove the double delay. Signed-off-by:
-
Bragatheswaran Manickavel authored
Use the standard max() helper macros instead of direct variable comparison using if/else blocks or ternary operator. Change identified using minmax.cocci Coccinelle semantic patch. Signed-off-by:
Bragatheswaran Manickavel <bragathemanick0908@gmail.com> Acked-by:
Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com> Link: https://lore.kernel.org/r/20231027094410.3706-1-bragathemanick0908@gmail.comSigned-off-by:
-
Andrew Hepp authored
Add support for the MCP9600 thermocouple electromotive force converter. The sensor has integrated cold junction compensation and a typical accuracy of 0.5 degrees Celsius. The driver supports a resolution of 0.0625 degrees Celsius. Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/MCP960X-Data-Sheet-20005426.pdfSigned-off-by:
Andrew Hepp <andrew.hepp@ahepp.dev> Link: https://lore.kernel.org/r/20231025233153.5454-2-andrew.hepp@ahepp.devSigned-off-by:
-
Andrew Hepp authored
Add support for the MCP9600 thermocouple electromotive force converter. The sensor has integrated cold junction compensation and a typical accuracy of 0.5 degrees Celsius. The driver supports a resolution of 0.0625 degrees Celsius. Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/MCP960X-Data-Sheet-20005426.pdfSigned-off-by:
-
Colin Ian King authored
There are two spelling mistakes in dev_err messages. Fix them. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Reviewed-by:
Jagath Jog J <jagathjog1996@gmail.com> Link: https://lore.kernel.org/r/20231023081054.617292-1-colin.i.king@gmail.comSigned-off-by:
-
Angel Iglesias authored
Add BMP390 device ID to the supported IDs on bmp380 sensor family Signed-off-by:
Angel Iglesias <ang.iglesiasg@gmail.com> Link: https://lore.kernel.org/r/d6a9e9ca4670c7401545d0d086cd3059e29044c8.1697994521.git.ang.iglesiasg@gmail.comSigned-off-by:
-
Angel Iglesias authored
Improve device detection in certain chip families known to have various chip IDs. When no ID matches, give a warning but follow along what device said on the firmware side and try to configure it. Signed-off-by:
-
Angel Iglesias authored
Small cleanup reordering local variable declarations following reverse christmas tree convention. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/bb63a996eb9c4555bf83471770f0169d2627e79c.1697994521.git.ang.iglesiasg@gmail.comSigned-off-by:
-
Angel Iglesias authored
Use the spi_get_device_match_data() helper instead of device_get_match_data() and the fallback match_id logic. Signed-off-by:
-
Biju Das authored
Replace device_get_match_data() and id lookup for retrieving match data by i2c_get_match_data(). Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by:
-
Lukas Bulwahn authored
Commit b512c767e7bc ("iio: imu: Add driver for BMI323 IMU") adds the MAINTAINERS section BOSCH SENSORTEC BMI323 IMU IIO DRIVER and refers to a non-existing device-tree file. Probably, this mistake was introduced by copying from the BOSCH SENSORTEC BMA400 ACCELEROMETER IIO DRIVER section and missing to adjust the file entry properly. This is however easily caught, as the script ./scripts/get_maintainer.pl --self-test=patterns complains about a broken reference. The related commit 77583938740e ("dt-bindings: iio: imu: Add Bosch BMI323") adds bosch,bmi323.yaml, so refer to that intended file instead. Signed-off-by: -
Amit Dhingra authored
Commit ca11e4a3 ("MAINTAINERS: Add IIO gain-time-scale helpers"), updates the MAINTAINERS file. However the files listed do not exist. These presumably come from commit 38416c28 ("iio: light: Add gain-time-scale helpers") Fix the entries. Found by ./scripts/get_maintainer.pl --self-test=patterns Fixes: ca11e4a3 ("MAINTAINERS: Add IIO gain-time-scale helpers") Signed-off-by:
Amit Dhingra <mechanicalamit@gmail.com> Acked-by:
-
Matti Vaittinen authored
The RGB + IR data can be used to calculate the illuminance value (luxes). Implement the equation obtained from the ROHM HW colleagues and add a raw light data channel outputting illuminance values in (nano) Luxes. Both the read_raw and buffering values are supported, with the limitation that buffering is only allowed when a suitable scan-mask is used. (RGB+IR, no clear). The equation has been developed by ROHM HW colleagues for open air sensor. Adding any lens to the sensor is likely to impact to used c1, c2, c3 coefficients. Also, the output values have only been tested on BU27008. According to the HW colleagues, the very same equation should work on BU27010 as well. Calculate and output illuminance values from BU27008 and BU27010. Signed-off-by:
-
Li peiyu authored
They are appear to be spelling mistakes, drivers/iio/pressure/bmp280.h:413 endianess->endianness drivers/iio/pressure/bmp280-core.c:923 dregrees->degrees drivers/iio/pressure/bmp280-core.c:1388 reescale->rescale drivers/iio/pressure/bmp280-core.c:1415 reescale->rescale Signed-off-by:
Li peiyu <579lpy@gmail.com> Link: https://lore.kernel.org/r/20231021070903.6051-1-579lpy@gmail.comSigned-off-by:
-
Matt Ranostay authored
Signed-off-by:
Matt Ranostay <matt@ranostay.sg> Link: https://lore.kernel.org/r/20231021085250.21431-1-matt@ranostay.sgSigned-off-by:
-
Andy Shevchenko authored
Replace open coded device_property_match_property_string(). Signed-off-by:
-
Andy Shevchenko authored
Replace open coded device_property_match_property_string(). Signed-off-by:
-
Andy Shevchenko authored
Replace open coded device_property_match_property_string(). Signed-off-by:
-
Andy Shevchenko authored
Replace open coded device_property_match_property_string(). Signed-off-by:
-
Andy Shevchenko authored
Sometimes the users want to match the single value string property against an array of predefined strings. Create a helper for them. Signed-off-by:
Rafael J. Wysocki <rafael@kernel.org> Link: https://lore.kernel.org/r/20230808162800.61651-3-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Andy Shevchenko authored
Use fwnode_property_string_array_count() instead of open coded variant. Signed-off-by:
-
David Lechner authored
This adds support for the optional reset gpio to the ad2s1210 resolver driver. If the gpio is present in the device tree, it is toggled during driver probe before the reset of the device initialization. As per the devicetree bindings, it is expected for the gpio to configured as active low. Suggested-by:
Michael Hennerich <Michael.Hennerich@analog.com> Signed-off-by:
David Lechner <dlechner@baylibre.com> Acked-by:
-
David Lechner authored
It is possible to use the AD2S1210 with hardwired mode pins (A0 and A1). According to the devicetree bindings, in this case the adi,fixed-mode property will specify which of the 3 possible modes the mode pins are hardwired for and the gpio-modes property is not allowed. This adds support for the case where the mode pins are hardwired for config mode. In this configuration, the position and value must be read from the config register. The case of hardwired position or velocity mode is not supported as there would be no way to configure the device. Signed-off-by:
Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20231016135423.16808-1-dlechner@baylibre.comSigned-off-by:
-
Jagath Jog J authored
The Bosch BMI323 is a 6-axis low-power IMU that provide measurements for acceleration, angular rate, and temperature. This sensor includes motion-triggered interrupt features, such as a step counter, tap detection, and activity/inactivity interrupt capabilities. The driver supports various functionalities, including data ready, FIFO data handling, and events such as tap detection, step counting, and activity interrupts. Signed-off-by:
-
Jagath Jog J authored
Add devicetree description document for Bosch BMI323, a 6-Axis IMU. Signed-off-by:
-
Ivan Mikhaylov authored
The MAX34408/MAX34409 are two- and four-channel current monitors that are configured and monitored with a standard I2C/SMBus serial interface. Each unidirectional current sensor offers precision high-side operation with a low full-scale sense voltage. The devices automatically sequence through two or four channels and collect the current-sense samples and average them to reduce the effect of impulse noise. The raw ADC samples are compared to user-programmable digital thresholds to indicate overcurrent conditions. Overcurrent conditions trigger a hardware output to provide an immediate indication to shut down any necessary external circuitry. Add as ADC driver which only supports current monitoring for now. Link: https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdfSigned-off-by:
Ivan Mikhaylov <fr0st61te@gmail.com> Link: https://lore.kernel.org/r/20231014211254.16719-3-fr0st61te@gmail.comSigned-off-by:
-
Ivan Mikhaylov authored
The hardware binding for i2c current monitoring device with overcurrent control. Signed-off-by:
-
- 13 Nov, 2023 1 commit
-
-
Linus Torvalds authored
-
- 12 Nov, 2023 4 commits
-
-
Miri Korenblit authored
The commands should be sorted inside the group definition. Fix the ordering so we won't get following warning: WARN_ON(iwl_cmd_groups_verify_sorted(trans_cfg)) Link: https://lore.kernel.org/regressions/2fa930bb-54dd-4942-a88d-05a47c8e9731@gmail.com/ Link: https://lore.kernel.org/linux-wireless/CAHk-=wix6kqQ5vHZXjOPpZBfM7mMm9bBZxi2Jh7XnaKCqVf94w@mail.gmail.com/ Fixes: b6e3d1ba ("wifi: iwlwifi: mvm: implement new firmware API for statistics") Tested-by:
Niklāvs Koļesņikovs <pinkflames.linux@gmail.com> Tested-by:
Damian Tometzki <damian@riscv-rocks.de> Acked-by:
Kalle Valo <kvalo@kernel.org> Signed-off-by:
Miri Korenblit <miriam.rachel.korenblit@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Merge tag 'parisc-for-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux Pull parisc architecture fixes from Helge Deller: - Include the upper 5 address bits when inserting TLB entries on a 64-bit kernel. On physical machines those are ignored, but in qemu it's nice to have them included and to be correct. - Stop the 64-bit kernel and show a warning if someone tries to boot on a machine with a 32-bit CPU - Fix a "no previous prototype" warning in parport-gsc * tag 'parisc-for-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: Prevent booting 64-bit kernels on PA1.x machines parport: gsc: mark init function static parisc/pgtable: Do not drop upper 5 address bits of physical address
-
Linus Torvalds authored
Merge tag 'loongarch-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson Pull LoongArch updates from Huacai Chen: - support PREEMPT_DYNAMIC with static keys - relax memory ordering for atomic operations - support BPF CPU v4 instructions for LoongArch - some build and runtime warning fixes * tag 'loongarch-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson: selftests/bpf: Enable cpu v4 tests for LoongArch LoongArch: BPF: Support signed mod instructions LoongArch: BPF: Support signed div instructions LoongArch: BPF: Support 32-bit offset jmp instructions LoongArch: BPF: Support unconditional bswap instructions LoongArch: BPF: Support sign-extension mov instructions LoongArch: BPF: Support sign-extension load instructions LoongArch: Add more instruction opcodes and emit_* helpers LoongArch/smp: Call rcutree_report_cpu_starting() earlier LoongArch: Relax memory ordering for atomic operations LoongArch: Mark __percpu functions as always inline LoongArch: Disable module from accessing external data directly LoongArch: Support PREEMPT_DYNAMIC with static keys
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: - Finish a refactor of pgprot_framebuffer() which dependend on some changes that were merged via the drm tree - Fix some kernel-doc warnings to quieten the bots Thanks to Nathan Lynch and Thomas Zimmermann. * tag 'powerpc-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/rtas: Fix ppc_rtas_rmo_buf_show() kernel-doc powerpc/pseries/rtas-work-area: Fix rtas_work_area_reserve_arena() kernel-doc powerpc/fb: Call internal __phys_mem_access_prot() in fbdev code powerpc: Remove file parameter from phys_mem_access_prot() powerpc/machdep: Remove trailing whitespaces
-
