Marvell 88E1111 currently uses the generic marvell config ANEG function.
This function has a sequence accessing Page 5 and Register 31,
both of which are not defined or reserved for this PHY.
Hence this patch adds a new config ANEG function for Marvell 88E1111
without these erroneous accesses.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sven Eckelmann says:

====================
batman-adv: Fixes for Linux 4.7

Antonio currently seems to be occupied. This is currently rather unfortunate
because there are patches waiting in the batman-adv development repository
maint(enance) branch [1] since up to 6 weeks. I am now getting asked when
these patches will hit the distribution kernels and therefore decided to
submit these patches directly to netdev.

The patch from Simon works around the problem that warnings could be triggered
in the translation table code via packets using a VLAN not configured on the
target host. This warning was replaced with a rate limited info message.

Ben Hutchings found an superfluous batadv_softif_vlan_put in the error
handling code of the translation table while he backported the "batman-adv:
Fix reference counting of vlan object for tt_local_entry" patch to the stable
kernels. He noticed correctly that this batadv_softif_vlan_put should also
have been removed by the said patch.

The most requested fix at the moment is related to a double free in the
translation table code. It is a race condition which mostly happens on systems
with multiple cores and multiple network interface attached to batman-adv. Two
Freifunk communities which were haunted by weird crashes (with backtraces
reporting problems in other parts of the kernel) were kind enough to test this
patch. They reported that there systems are now running stable after applying
this patch.

An invalid memory access was detected in the batadv_icmp_packet_rr handling
code when receiving a skbuff with fragments. The last patch is fixing a memory
leak when the interface is removed via .dellink. The code to fix it was copied
from the code handling the legacy sysfs interface to remove netdevices from a
batman-adv netdevice.

There are still 28 patches in the development tree for v4.8 but I will leave
them to Antonio because these are cleanups and features and therefore for net-
next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The untagged vlan object is only destroyed when the interface is removed
via the legacy sysfs interface. But it also has to be destroyed when the
standard rtnl-link interface is used.

Fixes: 5d2c05b2 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb_linearize may reallocate the skb. This makes the calculated pointer
for ethhdr invalid. But it the pointer is used later to fill in the RR
field of the batadv_icmp_packet_rr packet.

Instead re-evaluate eth_hdr after the skb_linearize+skb_cow to fix the
pointer and avoid the invalid read.

Fixes: da6b8c20 ("batman-adv: generalize batman-adv icmp packet handling")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each batadv_tt_local_entry hold a single reference to a
batadv_softif_vlan.  In case a new entry cannot be added to the hash
table, the error path puts the reference, but the reference will also
now be dropped by batadv_tt_local_entry_release().

Fixes: a33d970d ("batman-adv: Fix reference counting of vlan object for tt_local_entry")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tt_req_node is added and removed from a list inside a spinlock. But the
locking is sometimes removed even when the object is still referenced and
will be used later via this reference. For example batadv_send_tt_request
can create a new tt_req_node (including add to a list) and later
re-acquires the lock to remove it from the list and to free it. But at this
time another context could have already removed this tt_req_node from the
list and freed it.

CPU#0

    batadv_batman_skb_recv from net_device 0
    -> batadv_iv_ogm_receive
      -> batadv_iv_ogm_process
        -> batadv_iv_ogm_process_per_outif
          -> batadv_tvlv_ogm_receive
            -> batadv_tvlv_ogm_receive
              -> batadv_tvlv_containers_process
                -> batadv_tvlv_call_handler
                  -> batadv_tt_tvlv_ogm_handler_v1
                    -> batadv_tt_update_orig
                      -> batadv_send_tt_request
                        -> batadv_tt_req_node_new
                           spin_lock(...)
                           allocates new tt_req_node and adds it to list
                           spin_unlock(...)
                           return tt_req_node

CPU#1

    batadv_batman_skb_recv from net_device 1
    -> batadv_recv_unicast_tvlv
      -> batadv_tvlv_containers_process
        -> batadv_tvlv_call_handler
          -> batadv_tt_tvlv_unicast_handler_v1
            -> batadv_handle_tt_response
               spin_lock(...)
               tt_req_node gets removed from list and is freed
               spin_unlock(...)

CPU#0

                      <- returned to batadv_send_tt_request
                         spin_lock(...)
                         tt_req_node gets removed from list and is freed
                         MEMORY CORRUPTION/SEGFAULT/...
                         spin_unlock(...)

This can only be solved via reference counting to allow multiple contexts
to handle the list manipulation while making sure that only the last
context holding a reference will free the object.

Fixes: a73105b8 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Amadeus Alfa <amadeus@chemnitz.freifunk.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a VLAN tagged frame is received and the corresponding VLAN is not
configured on the soft interface, it will splat a WARN on every packet
received. This is a quite annoying behaviour for some scenarios, e.g. if
bat0 is bridged with eth0, and there are arbitrary VLAN tagged frames
from Ethernet coming in without having any VLAN configuration on bat0.

The code should probably create vlan objects on the fly and
transparently transport these VLAN-tagged Ethernet frames, but until
this is done, at least the WARN splat should be replaced by a rate
limited output.

Fixes: 354136bc ("batman-adv: fix kernel crash due to missing NULL checks")
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we have a system which uses fixed PHY devices and calls
fixed_phy_register() then fixed_phy_unregister() we can exhaust the
number of fixed PHYs available after a while, since we keep incrementing
the variable phy_fixed_addr, but we never decrement it.

This patch fixes that by converting the fixed PHY allocation to using
IDA, which takes care of the allocation/dealloaction of the PHY
addresses for us.

Fixes: a7595121 ("net: phy: extend fixed driver with fixed_phy_register()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Diag intends to broadcast tcp_sk and udp_sk socket destruction.
Testing sk->sk_protocol for IPPROTO_TCP/IPPROTO_UDP alone is not
sufficient for this. Raw sockets can have the same type.

Add a test for sk->sk_type.

Fixes: eb4cb008 ("sock_diag: define destruction multicast groups")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The proc connector messages include a sequence number, allowing userspace
programs to detect lost messages.  However, performing this detection is
currently more difficult than necessary, since netlink messages can be
delivered to the application out-of-order.  To fix this, leave pre-emption
disabled during cn_netlink_send(), and use GFP_NOWAIT.

The following was written as a test case.  Building the kernel w/ make -j32
proved a reliable way to generate out-of-order cn_proc messages.

int
main(int argc, char *argv[])
{
	static uint32_t last_seq[CPU_SETSIZE], seq;
	int cpu, fd;
	struct sockaddr_nl sa;
	struct __attribute__((aligned(NLMSG_ALIGNTO))) {
		struct nlmsghdr nl_hdr;
		struct __attribute__((__packed__)) {
			struct cn_msg cn_msg;
			struct proc_event cn_proc;
		};
	} rmsg;
	struct __attribute__((aligned(NLMSG_ALIGNTO))) {
		struct nlmsghdr nl_hdr;
		struct __attribute__((__packed__)) {
			struct cn_msg cn_msg;
			enum proc_cn_mcast_op cn_mcast;
		};
	} smsg;

	fd = socket(PF_NETLINK, SOCK_DGRAM, NETLINK_CONNECTOR);
	if (fd < 0) {
		perror("socket");
	}

	sa.nl_family = AF_NETLINK;
	sa.nl_groups = CN_IDX_PROC;
	sa.nl_pid = getpid();
	if (bind(fd, (struct sockaddr *)&sa, sizeof(sa)) < 0) {
		perror("bind");
	}

	memset(&smsg, 0, sizeof(smsg));
	smsg.nl_hdr.nlmsg_len = sizeof(smsg);
	smsg.nl_hdr.nlmsg_pid = getpid();
	smsg.nl_hdr.nlmsg_type = NLMSG_DONE;
	smsg.cn_msg.id.idx = CN_IDX_PROC;
	smsg.cn_msg.id.val = CN_VAL_PROC;
	smsg.cn_msg.len = sizeof(enum proc_cn_mcast_op);
	smsg.cn_mcast = PROC_CN_MCAST_LISTEN;
	if (send(fd, &smsg, sizeof(smsg), 0) != sizeof(smsg)) {
		perror("send");
	}

	while (recv(fd, &rmsg, sizeof(rmsg), 0) == sizeof(rmsg)) {
		cpu = rmsg.cn_proc.cpu;
		if (cpu < 0) {
			continue;
		}
		seq = rmsg.cn_msg.seq;
		if ((last_seq[cpu] != 0) && (seq != last_seq[cpu] + 1)) {
			printf("out-of-order seq=%d on cpu=%d\n", seq, cpu);
		}
		last_seq[cpu] = seq;
	}

	/* NOTREACHED */

	perror("recv");

	return -1;
}
Signed-off-by: Aaron Campbell <aaron@monkey.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bridge is falsly dropping ipv6 mulitcast packets if there is:
 1. No ipv6 address assigned on the brigde.
 2. No external mld querier present.
 3. The internal querier enabled.

When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.

Ipv6 multicast snooping can only work if:
 a) An external querier is present
 OR
 b) The bridge has an ipv6 address an is capable of sending own queries

Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.

This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().

Special thanks to Linus Lüssing.

Fixes: d1d81d4c ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 311c7c71 ("net/mlx5e: Allocate DMA coherent memory on
reader NUMA node") introduced mlx5_*_alloc_node() but missed changing
some calling and warn messages. This patch introduces 2 changes:
	* Use mlx5_buf_alloc_node() instead of mlx5_buf_alloc() in
	  mlx5_wq_ll_create()
	* Update the failure warn messages with _node postfix for
	  mlx5_*_alloc function names

Fixes: 311c7c71 ("net/mlx5e: Allocate DMA coherent memory on reader NUMA node")
Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com>
Acked-By: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: bgmac: Random fixes

This patch series fixes a few issues spotted by code inspection and
actual testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

bgmac_open() calls phy_start() to initialize the PHY state machine,
which will set the interface's carrier state accordingly, no need to
force that as this could be conflicting with the PHY state determined by
PHYLIB.

Fixes: dd4544f0 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver does not start the transmit queue in bgmac_open(). If the
queue was stopped prior to closing then re-opening the interface, we
would never be able to wake-up again.

Fixes: dd4544f0 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are checking for the Start of Frame bit in the ctl1 word, while this
bit is set in the ctl0 word instead. Read the ctl0 word and update the
check to verify that.

Fixes: 9cde9450 ("bgmac: implement scatter/gather support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 7bb11dc9 ("bonding: unify all places where
actor-oper key needs to be updated."), the logic in bonding to handle
selection between multiple aggregators has not functioned.

	This affects only configurations wherein the bonding slaves
connect to two discrete aggregators (e.g., two independent switches, each
with LACP enabled), thus creating two separate aggregation groups within a
single bond.

	The cause is a change in 7bb11dc9 to no longer set
AD_PORT_BEGIN on a port after a link state change, which would cause the
port to be reselected for attachment to an aggregator as if were newly
added to the bond.  We cannot restore the prior behavior, as it
contradicts IEEE 802.1AX 5.4.12, which requires ports that "become
inoperable" (lose carrier, setting port_enabled=false as per 802.1AX
5.4.7) to remain selected (i.e., assigned to the aggregator).  As the port
now remains selected, the aggregator selection logic is not invoked.

	A side effect of this change is that aggregators in bonding will
now contain ports that are link down.  The aggregator selection logic
does not currently handle this situation correctly, causing incorrect
aggregator selection.

	This patch makes two changes to repair the aggregator selection
logic in bonding to function as documented and within the confines of the
standard:

	First, the aggregator selection and related logic now utilizes the
number of active ports per aggregator, not the number of selected ports
(as some selected ports may be down).  The ad_select "bandwidth" and
"count" options only consider ports that are link up.

	Second, on any carrier state change of any slave, the aggregator
selection logic is explicitly called to insure the correct aggregator is
active.
Reported-by: Veli-Matti Lintu <veli-matti.lintu@opinsys.fi>
Fixes: 7bb11dc9 ("bonding: unify all places where actor-oper key needs to be updated.")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes wrong-interface signaling on 32-bit platforms for entries
created when jiffies > 2^31 + MFC_ASSERT_THRESH.
Signed-off-by: Tom Goff <thomas.goff@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are several places where the listener and pending or accept queue
child sockets are accessed at the same time.  Lockdep is unhappy that
two locks from the same class are held.

Tell lockdep that it is safe and document the lock ordering.

Originally Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> sent a similar
patch asking whether this is safe.  I have audited the code and also
covered the vsock_pending_work() function.
Suggested-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

with the commit 8c14586f ("net: ipv6: Use passed in table for
nexthop lookups"), net hop lookup is first performed on route creation
in the passed-in table.
However device match is not enforced in table lookup, so the found
route can be later discarded due to egress device mismatch and no
global lookup will be performed.
This cause the following to fail:

ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip route add 2001:db8:8086::/48 dev dummy1 metric 20
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy1 metric 20
ip route add 2001:db8:8086::/48 dev dummy2 metric 21
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy2 metric 21
RTNETLINK answers: No route to host

This change fixes the issue enforcing device lookup in
ip6_nh_lookup_table()

v1->v2: updated commit message title

Fixes: 8c14586f ("net: ipv6: Use passed in table for nexthop lookups")
Reported-and-tested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.7-20160623' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-06-23

this is a pull request of 3 patches for the upcoming linux-4.7 release.

The first two patches are by Oliver Hartkopp fixing oopes in the generic CAN
device netlink handling. Jimmy Assarsson's patch for the kvaser_usb driver adds
support for more devices by adding their USB product ids.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

By default, mdiobus_alloc() sets the PHYs to polling mode, but a
pointer size memcpy means that a couple IRQs end up being overwritten
with a value of 0. This means that PHY_POLL is disabled and results
in unpredictable behavior depending on the PHY's location on the
MDIO bus. Remove that memcpy and the now unused phy_irq member to
force the SMSC911x PHYs into polling mode 100% of the time.

Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tariq Toukan is replacing Eugenia (Jenny) Emantayev as the mlx4
Ethernet driver maintainer, thanks to Jenny and good luck to him.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.7

iwlwifi

* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted

rtl8xxxu

* fix typo on variable name

ath10k

* fix deadlock when peer cannot be created
* fix crash related to printing features
* fix deadlock while processing rx_in_ord_ind

ath9k

* fix GPIO mask regression for AR9462 and AR9565
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tx errors present summation of errors encountered while transmitting
packets.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The assignment of rth->dst.output in vrf_rt6_create() and
vrf_rtable_create() used a hard tab before the '='. The neighboring
assignments did not. Make the assignment of rth->dst.output consistent
with the surrounding code.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the packet was dropped by lower qdisc, then we must not
access it later.

Save qdisc_pkt_len(skb) in a temp variable.

Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexey reported that we have GFP_KERNEL allocation when
holding the spinlock tcf_lock. Actually we don't have
to take that spinlock for all the cases, especially
for the new one we just create. To modify the existing
actions, we still need this spinlock to make sure
the whole update is atomic.

For net-next, we can get rid of this spinlock because
we already hold the RTNL lock on slow path, and on fast
path we can use RCU to protect the metalist.

Joint work with Jamal.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Blair Steven noticed that ESN in conjunction with UDP encapsulation
is broken because we set the temporary ESP header to the wrong spot.

This patch fixes this by first of all using the right spot, i.e.,
4 bytes off the real ESP header, and then saving this information
so that after encryption we can restore it properly.

Fixes: 7021b2e1 ("esp4: Switch to new AEAD interface")
Reported-by: Blair Steven <Blair.Steven@alliedtelesis.co.nz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for Kvaser Leaf Light HS v2 OEM, Mini PCI
Express 2xHS and USBcan Light 2xHS.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...

This patch adds a private dellink function for the CAN device driver interface
that does just nothing.

It's a follow up to commit 993e6f2f ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

With upstream commit bb208f14 (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.

When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Tariq Toukan says:

====================
mlx4_en fixes for 4.7-rc

This small patchset includes two small fixes for mlx4_en driver.

One allows a clean shutdown even when clients do not release their
netdev reference.
The other adds error return values to the VLAN VID add/kill functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows a clean shutdown, even if some netdev clients do not
release their reference from this netdev. It is enough to release
the HW resources only as the kernel is shutting down.

Fixes: 2ba5fbd6 ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify mlx4_en_vlan_rx_[add/kill]_vid to return error value in case of
failure.

Fixes: 8e586137 ('net: make vlan ndo_vlan_rx_[add/kill]_vid return error value')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When extracting an individual message from a received "bundle" buffer,
we just create a clone of the base buffer, and adjust it to point into
the right position of the linearized data area of the latter. This works
well for regular message reception, but during periods of extremely high
load it may happen that an extracted buffer, e.g, a connection probe, is
reversed and forwarded through an external interface while the preceding
extracted message is still unhandled. When this happens, the header or
data area of the preceding message will be partially overwritten by a
MAC header, leading to unpredicatable consequences, such as a link
reset.

We now fix this by ensuring that the msg_reverse() function never
returns a cloned buffer, and that the returned buffer always contains
sufficient valid head and tail room to be forwarded.
Reported-by: Erik Hugne <erik.hugne@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every open of /proc/net/kcm leaks 16 bytes of memory as is reported by
kmemleak:
unreferenced object 0xffff88059c0e3458 (size 192):
  comm "cat", pid 1401, jiffies 4294935742 (age 310.720s)
  hex dump (first 32 bytes):
    28 45 71 96 05 88 ff ff 00 10 00 00 00 00 00 00  (Eq.............
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8156a2de>] kmem_cache_alloc_trace+0x16e/0x230
    [<ffffffff8162a479>] seq_open+0x79/0x1d0
    [<ffffffffa0578510>] kcm_seq_open+0x0/0x30 [kcm]
    [<ffffffff8162a479>] seq_open+0x79/0x1d0
    [<ffffffff8162a8cf>] __seq_open_private+0x2f/0xa0
    [<ffffffff81712548>] seq_open_net+0x38/0xa0
...

It is caused by a missing free in the ->release path. So fix it by
providing seq_release_net as the ->release method.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: cd6e111b (kcm: Add statistics and proc interfaces)
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tom Herbert <tom@herbertland.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Both dev_uc_sync_multiple() and dev_mc_sync_multiple() require the
source device to be locked by netif_addr_lock_bh(), but this is missing
in team's enslave function, so add it.

This fixes the following lockdep warning:

Possible interrupt unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(_xmit_ETHER/1);
                                local_irq_disable();
                                lock(&(&mc->mca_lock)->rlock);
                                lock(&team_netdev_addr_lock_key);
   <Interrupt>
     lock(&(&mc->mca_lock)->rlock);

  *** DEADLOCK ***

Fixes: cb41c997 ("team: team should sync the port's uc/mc addrs when add a port")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.7-20160620' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-06-20

this is a pull request of 3 patches for the upcoming linux-4.7 release.

The first patch is by Thor Thayer for the c_can/d_can driver. It fixes the
registar access on Altera Cyclone devices, which caused CAN frames to have 0x0
in the first two bytes incorrectly. Wolfgang Grandegger's patch for the at91
driver fixes a hanging driver under high bus load situations. A patch for the
gs_usb driver by Maximilian Schneider adds support for the bytewerk.org
candleLight interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>