- 02 May, 2018 28 commits
-
-
Maxime Ripard authored
In order to improve readibility and reusability, let's move the bus width setup to a small function called by our .set_ios hook. Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Maxime Ripard authored
All the other functions in the driver take a struct sunxi_mmc_host pointer. Let's make it consistent. Signed-off-by:
-
Maxime Ripard authored
Our headers sort algorithm has had pretty chaotic results. Let's fix that. Signed-off-by:
-
Ezequiel Garcia authored
Now that we have MMC support, enable ext2/3/4 support in the CI20 defconfig. Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Acked-by:
James Hogan <jhogan@kernel.org> Signed-off-by:
-
Diwakar Sharma authored
This patch uses limit clock rate quirk to reduce clock rate for "SDR104" mode on IMX side for Marvell 8887 WiFi + Bluetooth chip side, as Marvell does not recommend to use SDIO at the speed of higher than 150MHz. Signed-off-by:
Diwakar Sharma <diwakar.sharma@in.bosch.com> Signed-off-by:
Harish Jenny K N <harish_kandiga@mentor.com> Signed-off-by:
-
harish_kandiga@mentor.com authored
This patch adds a quirk to limit clock rate which can be used to reduce the SDIO clock rate for some chips with broken UHS. Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
-
Shawn Lin authored
DDR52 with 8-bit mode should be handled in a different way when requesting ciu_clk. However DDR50 is used for SDMMC/SDIO and could never be possible with 8-bit mode. It's trival but misleading. Signed-off-by:
-
Masahiro Yamada authored
Cadence sent out an errata report to their customers of this IP. This errata is not so severe, but the tune request should be sent twice to avoid the potential issue. Quote from the report: Problem Summary --------------- The IP6116 SD/eMMC PHY design has a timing issue on receive data path. This issue may lead to an incorrect values of read/write pointers of the synchronization FIFO. Such a situation can happen at the SDR104 and HS200 tuning procedure when the PHY is requested to change a phase of sampling clock when moving to the next tuning iteration. Workarounds ----------- The following are valid workarounds to resolve the issue: 1. In eMMC mode, software sends tune request twice instead of once at each iteration. This means that the clock phase is not changed on the second request so there is no potential for clock instability. 2. In SD mode, software must not use the hardware tuning and instead perform an almost identical procedure to eMMC, using the HRS34 Tune Force register. Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Nan Li authored
Explicitly update the docomentation to support the Meson-AXG platform. Signed-off-by:
Nan Li <nan.li@amlogic.com> Signed-off-by:
Yixun Lan <yixun.lan@amlogic.com> Signed-off-by:
Kevin Hilman <khilman@baylibre.com>
-
Nan Li authored
Introduce the compatible data to cover the register offset & mask change of the eMMC controller in Amlogic's Meson-AXG SoC. Signed-off-by:
-
Nan Li authored
Update the documentation to list support for Meson-AXG SoC explicitly. The new binding string is necessary since this SoC introduce a few IP difference comparing to previous old generation. Signed-off-by:
-
Andrew Gabbasov authored
Since RPMB area is accessible via special ioctl only and boot areas are unlikely to contain any partitions, exclude them all from listing in /proc/partitions. This will hide them from various user-level software (e.g. fdisk), thus avoiding unnecessary access attempts. Signed-off-by:
Andrew Gabbasov <andrew_gabbasov@mentor.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Ezequiel Garcia authored
Enable the SD/MMC support, along with DMA engine support in the CI20 defconfig. Acked-by:
Mathieu Malaterre <malat@debian.org> Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.co.uk> Signed-off-by:
-
Ezequiel Garcia authored
Now that we have support for JZ480 SoCs in the MMC driver, let's enable it on the devicetree. Acked-by:
-
Ezequiel Garcia authored
Add the devicetree node to support the MMC host controller available in JZ480 SoCs. Acked-by:
-
Ezequiel Garcia authored
Add the devicetree node to support the DMA controller found in JZ480 SoCs. Tested-by:
-
Ezequiel Garcia authored
Replace dma_request_channel() with dma_request_chan(), which also supports probing from the devicetree. Tested-by:
-
Alex Smith authored
Add support for the JZ4780 MMC controller to the jz47xx_mmc driver. There are a few minor differences from the 4740 to the 4780 that need to be handled, but otherwise the controllers behave the same. The IREG and IMASK registers are expanded to 32 bits. Additionally, some error conditions are now reported in both STATUS and IREG. Writing IREG before reading STATUS causes the bits in STATUS to be cleared, so STATUS must be read first to ensure we see and report error conditions correctly. Signed-off-by:
Alex Smith <alex.smith@imgtec.com> Signed-off-by:
Paul Cercueil <paul@crapouillou.net> Tested-by:
-
Alex Smith authored
The maximum clock rate can be overridden by DT. The clock rate should be set to the DT-specified value rather than the constant JZ_MMC_CLK_RATE when this is done. If the maximum clock rate is not set by DT then mmc->f_max will be set to JZ_MMC_CLK_RATE. Tested-by:
-
Ezequiel Garcia authored
Add the devicetree binding for JZ4740/JZ4780 SoC MMC/SD controller. Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Ezequiel Garcia authored
Add support to probe the device via devicetree, which will be used to support other SoCs such as the JZ4780. Based on commits from the CI20 repo, by Paul Cercueil and Alex Smith. Binding document based on work by Zubair Lutfullah Kakakhel. Tested-by:
-
Zubair Lutfullah Kakakhel authored
In case a bootloader leaves the device in a bad state, requesting the interrupt before resetting results in a bad interrupt loop. Signed-off-by:
Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> [Ezequiel: cleanup commit description] Tested-by:
-
Ezequiel Garcia authored
Instead of accessing the platform data pointer directly, use the dev_get_platdata() helper. Tested-by:
-
Ezequiel Garcia authored
Just a minor cleanup to order the headers alphabetically. This helps prevent merge conflicts. Tested-by:
-
Paul Cercueil authored
Currently, if jz4740_mmc_request_gpios() fails, the driver tries to release DMA resources. This is wrong because DMA is requested at a later stage. Signed-off-by:
-
Shawn Lin authored
Respect the actual clock for mmc debugfs to help better debug the hardware. mmc_host mmc0: Bus speed (slot 0) = 135475200Hz (slot req 150000000Hz, actual 135475200HZ div = 0) cat /sys/kernel/debug/mmc0/ios clock: 150000000 Hz actual clock: 135475200 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 3 (8 bits) timing spec: 9 (mmc HS200) signal voltage: 0 (1.80 V) driver type: 0 (driver type B) Cc: Xiao Yao <xiaoyao@rock-chips.com> Cc: Ziyuan <xzy.xu@rock-chips.com> Signed-off-by:
-
Tobin C. Harding authored
The use of stack Variable Length Arrays needs to be avoided, as they can be a vector for stack exhaustion, which can be both a runtime bug (kernel Oops) or a security flaw (overwriting memory beyond the stack). Also, in general, as code evolves it is easy to lose track of how big a VLA can get. Thus, we can end up having runtime failures that are hard to debug. As part of the directive[1] to remove all VLAs from the kernel, and build with -Wvla. Currently driver is using a VLA declared using the number of descriptors. This array is used to store integer values and is later used as an argument to `gpiod_set_array_value_cansleep()` This can be avoided by using `kmalloc_array()` to allocate memory for the array of integer values. Memory is free'd before return from function. >From the code it appears that it is safe to sleep so we can use GFP_KERNEL (based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`. It can be expected that this patch will result in a small increase in overhead due to the use of `kmalloc_array()` [1] https://lkml.org/lkml/2018/3/7/621Signed-off-by:
Tobin C. Harding <me@tobin.cc> Signed-off-by:
-
Phil Edworthy authored
On SD 2.00 cards we get lots of these messages: "mmc0: Got data interrupt 0x00000002 even though no data operation was in progress" By applying the SDHCI_QUIRK2_STOP_WITH_TC quirk, the messages no longer happen. A single card claiming to be SD 3.00 compliant also generates the interrupts, but since the card's manfacturing date is 2002 mar, it's unlikely to really be SD 3.00. This card is a 8GB SanDisk 'SU08G' 8.0 (SDHC class 4). This has been reported on Xilinx devices that also use the Arasan IP. See https://patchwork.kernel.org/patch/8062871/ This has been tested on the Renesas RZ/ND-DB board with the RZ/N1 SoC. The Arasan IP in this device is version 1.39a and uses a max SD clock of 50MHz and does not support DDR modes. Signed-off-by:
Phil Edworthy <phil.edworthy@renesas.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
- 29 Apr, 2018 6 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "Another set of x86 related updates: - Fix the long broken x32 version of the IPC user space headers which was noticed by Arnd Bergman in course of his ongoing y2038 work. GLIBC seems to have non broken private copies of these headers so this went unnoticed. - Two microcode fixlets which address some more fallout from the recent modifications in that area: - Unconditionally save the microcode patch, which was only saved when CPU_HOTPLUG was enabled causing failures in the late loading mechanism - Make the later loader synchronization finally work under all circumstances. It was exiting early and causing timeout failures due to a missing synchronization point. - Do not use mwait_play_dead() on AMD systems to prevent excessive power consumption as the CPU cannot go into deep power states from there. - Address an annoying sparse warning due to lost type qualifiers of the vmemmap and vmalloc base address constants. - Prevent reserving crash kernel region on Xen PV as this leads to the wrong perception that crash kernels actually work there which is not the case. Xen PV has its own crash mechanism handled by the hypervisor. - Add missing TLB cpuid values to the table to make the printout on certain machines correct. - Enumerate the new CLDEMOTE instruction - Fix an incorrect SPDX identifier - Remove stale macros" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/ipc: Fix x32 version of shmid64_ds and msqid64_ds x86/setup: Do not reserve a crash kernel region if booted on Xen PV x86/cpu/intel: Add missing TLB cpuid values x86/smpboot: Don't use mwait_play_dead() on AMD systems x86/mm: Make vmemmap and vmalloc base address constants unsigned long x86/vector: Remove the unused macro FPU_IRQ x86/vector: Remove the macro VECTOR_OFFSET_START x86/cpufeatures: Enumerate cldemote instruction x86/microcode: Do not exit early from __reload_late() x86/microcode/intel: Save microcode patch unconditionally x86/jailhouse: Fix incorrect SPDX identifier -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 pti fixes from Thomas Gleixner: "A set of updates for the x86/pti related code: - Preserve r8-r11 in int $0x80. r8-r11 need to be preserved, but the int$80 entry code removed that quite some time ago. Make it correct again. - A set of fixes for the Global Bit work which went into 4.17 and caused a bunch of interesting regressions: - Triggering a BUG in the page attribute code due to a missing check for early boot stage - Warnings in the page attribute code about holes in the kernel text mapping which are caused by the freeing of the init code. Handle such holes gracefully. - Reduce the amount of kernel memory which is set global to the actual text and do not incidentally overlap with data. - Disable the global bit when RANDSTRUCT is enabled as it partially defeats the hardening. - Make the page protection setup correct for vma->page_prot population again. The adjustment of the protections fell through the crack during the Global bit rework and triggers warnings on machines which do not support certain features, e.g. NX" * 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/entry/64/compat: Preserve r8-r11 in int $0x80 x86/pti: Filter at vma->vm_page_prot population x86/pti: Disallow global kernel text with RANDSTRUCT x86/pti: Reduce amount of kernel text allowed to be Global x86/pti: Fix boot warning from Global-bit setting x86/pti: Fix boot problems from Global-bit setting -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "Two fixes from the timer departement: - Fix a long standing issue in the NOHZ tick code which causes RB tree corruption, delayed timers and other malfunctions. The cause for this is code which modifies the expiry time of an enqueued hrtimer. - Revert the CLOCK_MONOTONIC/CLOCK_BOOTTIME unification due to regression reports. Seems userspace _is_ relying on the documented behaviour despite our hope that it wont" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: Revert: Unify CLOCK_MONOTONIC and CLOCK_BOOTTIME tick/sched: Do not mess with an enqueued hrtimer -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Thomas Gleixner: "The perf update contains the following bits: x86: - Prevent setting freeze_on_smi on PerfMon V1 CPUs to avoid #GP perf stat: - Keep the '/' event modifier separator in fallback, for example when fallbacking from 'cpu/cpu-cycles/' to user level only, where it should become 'cpu/cpu-cycles/u' and not 'cpu/cpu-cycles/:u' (Jiri Olsa) - Fix PMU events parsing rule, improving error reporting for invalid events (Jiri Olsa) - Disable write_backward and other event attributes for !group events in a group, fixing, for instance this group: '{cycles,msr/aperf/}:S' that has leader sampling (:S) and where just the 'cycles', the leader event, should have the write_backward attribute set, in this case it all fails because the PMU where 'msr/aperf/' lives doesn't accepts write_backward style sampling (Jiri Olsa) - Only fall back group read for leader (Kan Liang) - Fix core PMU alias list for x86 platform (Kan Liang) - Print out hint for mixed PMU group error (Kan Liang) - Fix duplicate PMU name for interval print (Kan Liang) Core: - Set main kernel end address properly when reading kernel and module maps (Namhyung Kim) perf mem: - Fix incorrect entries and add missing man options (Sangwon Hong) s/390: - Remove s390 specific strcmp_cpuid_cmp function (Thomas Richter) - Adapt 'perf test' case record+probe_libc_inet_pton.sh for s390 - Fix s390 undefined record__auxtrace_init() return value in 'perf record' (Thomas Richter)" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/x86/intel: Don't enable freeze-on-smi for PerfMon V1 perf stat: Fix duplicate PMU name for interval print perf evsel: Only fall back group read for leader perf stat: Print out hint for mixed PMU group error perf pmu: Fix core PMU alias list for X86 platform perf record: Fix s390 undefined record__auxtrace_init() return value perf mem: Document incorrect and missing options perf evsel: Disable write_backward for leader sampling group events perf pmu: Fix pmu events parsing rule perf stat: Keep the / modifier separator in fallback perf test: Adapt test case record+probe_libc_inet_pton.sh for s390 perf list: Remove s390 specific strcmp_cpuid_cmp function perf machine: Set main kernel end address properly -
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Fix misc bugs and a regression for ext4" * tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: add MODULE_SOFTDEP to ensure crc32c is included in the initramfs ext4: fix bitmap position validation ext4: set h_journal if there is a failure starting a reserved handle ext4: prevent right-shifting extents beyond EXT_MAX_BLOCKS
-
- 28 Apr, 2018 6 commits
-
-
Amir Goldstein authored
The comment claims that this helper will try not to loose bits, but for 64bit long it looses the high bits before hashing 64bit long into 32bit int. Use the helper hash_long() to do the right thing for 64bit long. For 32bit long, there is no change. All the callers of end_name_hash() either assign the result to qstr->hash, which is u32 or return the result as an int value (e.g. full_name_hash()). Change the helper return type to int to conform to its users. [ It took me a while to apply this, because my initial reaction to it was - incorrectly - that it could make for slower code. After having looked more at it, I take back all my complaints about the patch, Amir was right and I was mis-reading things or just being stupid. I also don't worry too much about the possible performance impact of this on 64-bit, since most architectures that actually care about performance end up not using this very much (the dcache code is the most performance-critical, but the word-at-a-time case uses its own hashing anyway). So this ends up being mostly used for filesystems that do their own degraded hashing (usually because they want a case-insensitive comparison function). A _tiny_ worry remains, in that not everybody uses DCACHE_WORD_ACCESS, and then this potentially makes things more expensive on 64-bit architectures with slow or lacking multipliers even for the normal case. That said, realistically the only such architecture I can think of is PA-RISC. Nobody really cares about performance on that, it's more of a "look ma, I've got warts^W an odd machine" platform. So the patch is fine, and all my initial worries were just misplaced from not looking at this properly. - Linus ] Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
David Sterba authored
The AFFS filesystem is still in use by m68k community (Link #2), but as there was no code activity and no maintainer, the filesystem appeared on the list of candidates for staging/removal (Link #1). I volunteer to act as a maintainer of AFFS to collect any fixes that might show up and to guard fs/affs/ against another spring cleaning. Link: https://lkml.kernel.org/r/20180425154602.GA8546@bombadil.infradead.org Link: https://lkml.kernel.org/r/1613268.lKBQxPXt8J@merkaba CC: Martin Steigerwald <martin@lichtvoll.de> CC: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c fixes from Wolfram Sang: - two driver fixes - better parameter check for the core - Documentation updates - part of a tree-wide HAS_DMA cleanup * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: sprd: Fix the i2c count issue i2c: sprd: Prevent i2c accesses after suspend is called i2c: dev: prevent ZERO_SIZE_PTR deref in i2cdev_ioctl_rdwr() Documentation/i2c: adopt kernel commenting style in examples Documentation/i2c: sync docs with current state of i2c-tools Documentation/i2c: whitespace cleanup i2c: Remove depends on HAS_DMA in case of platform dependency
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds authored
Pull crypto fixes from Herbert Xu: - crypto API regression that may cause sporadic alloc failures - double-free bug in drbg * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: drbg - set freed buffers to NULL crypto: api - fix finding algorithm currently being tested
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "A few security related fixes for SMB3, most importantly for SMB3.11 encryption" * tag '4.17-rc2-smb3' of git://git.samba.org/sfrench/cifs-2.6: cifs: smbd: Avoid allocating iov on the stack cifs: smbd: Don't use RDMA read/write when signing is used SMB311: Fix reconnect SMB3: Fix 3.11 encryption to Windows and handle encrypted smb3 tcon CIFS: set *resp_buf_type to NO_BUFFER on error
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: "A bunch of fixes, mostly for existing code and going to stable. Our memory hot-unplug path wasn't flushing the cache before removing memory. That is a problem now that we are doing memory hotplug on bare metal. Three fixes for the NPU code that supports devices connected via NVLink (ie. GPUs). The main one tweaks the TLB flush algorithm to avoid soft lockups for large flushes. A fix for our memory error handling where we would loop infinitely, returning back to the bad access and hard lockup the CPU. Fixes for the OPAL RTC driver, which wasn't handling some error cases correctly. A fix for a hardlockup in the powernv cpufreq driver. And finally two fixes to our smp_send_stop(), required due to a recent change to use it on shutdown. Thanks to: Alistair Popple, Balbir Singh, Laurentiu Tudor, Mahesh Salgaonkar, Mark Hairgrove, Nicholas Piggin, Rashmica Gupta, Shilpasri G Bhat" * tag 'powerpc-4.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/kvm/booke: Fix altivec related build break powerpc: Fix deadlock with multiple calls to smp_send_stop cpufreq: powernv: Fix hardlockup due to synchronous smp_call in timer interrupt powerpc: Fix smp_send_stop NMI IPI handling rtc: opal: Fix OPAL RTC driver OPAL_BUSY loops powerpc/mce: Fix a bug where mce loops on memory UE. powerpc/powernv/npu: Do a PID GPU TLB flush when invalidating a large address range powerpc/powernv/npu: Prevent overwriting of pnv_npu2_init_contex() callback parameters powerpc/powernv/npu: Add lock to prevent race in concurrent context init/destroy powerpc/powernv/memtrace: Let the arch hotunplug code flush cache powerpc/mm: Flush cache on memory hot(un)plug
-
