- 10 Dec, 2020 38 commits
-
-
Geliang Tang authored
This patch added a new add_addr_signal type named MPTCP_ADD_ADDR_PORT, to identify it is an address with port to be added. It also added a new parameter 'port' for both mptcp_add_addr_len and mptcp_pm_add_addr_signal. In mptcp_established_options_add_addr, we check whether the announced address is added with port. If it is, we put this port number to mptcp_out_options's port field. Signed-off-by:
Geliang Tang <geliangtang@gmail.com> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Geliang Tang authored
This patch uses adding up size to get the ADD_ADDR suboption length rather than returning the ADD_ADDR size constants. Signed-off-by:
-
Geliang Tang authored
In rfc8684, the length of ADD_ADDR suboption with IPv4 address and port is 18 octets, but mptcp_write_options is 32-bit aligned, so we need to pad it to 20 octets. All the other port related option lengths need to be added up 2 octets similarly. This patch added a new field 'port' in mptcp_out_options. When this field is set with a port number, we need to add up 4 octets for the ADD_ADDR suboption, and put the port number into the suboption. Signed-off-by:
-
Geliang Tang authored
The length of ADD_ADDR6 is 12 octets longer than ADD_ADDR. That's the only difference between them. This patch dropped the duplicate code between ADD_ADDR and ADD_ADDR6 suboptions writing, and unify them into one. Signed-off-by:
-
Geliang Tang authored
There are two differences between ADD_ADDR suboption and ADD_ADDR echo suboption: The length of the former is 8 octets longer than the length of the latter. The former's echo-flag is 0, and latter's echo-flag is 1. This patch added two local variables, len and echo, to unify ADD_ADDR and ADD_ADDR echo suboptions writing. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== 100GbE Intel Wired LAN Driver Updates 2020-12-09 This series contains updates to ice driver only. Bruce changes the allocation of ice_flow_prof_params from stack to heap to avoid excessive stack usage. Corrects a misleading comment and silences a sparse warning that is not a problem. Paul allows for HW initialization to continue if PHY abilities cannot be obtained. Jeb removes bypassing FW link override and reading Option ROM and netlist information for non-E810 devices as this is now available on other devices. Nick removes vlan_ena field as this information can be gathered by checking num_vlan. Jake combines format strings and debug prints to the same line. Simon adds a space to fix string concatenation. v4: Drop ACL patches. Change PHY abilities failure message from debug to warning. v3: Fix email address for DaveM and fix character in cover letter v2: Expand on commit message for patch 3 to show example usage/commands. Reduce number of defensive checks being done. ==================== Signed-off-by: -
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
-
Zheng Yongjun authored
Simplify the return expression. Signed-off-by:
-
David S. Miller authored
Bongsu Jeon says: ==================== nfc: s3fwrn5: Change I2C interrupt trigger to EDGE_RISING For stable Samsung's I2C interrupt handling, I changed the interrupt trigger from IRQ_TYPE_LEVEL_HIGH to IRQ_TYPE_EDGE_RISING and removed the hard coded interrupt trigger type in the i2c module for the flexible control. 1/2 is the changed dt binding for the edge rising trigger. 2/2 is to remove the hard coded interrupt trigger type in the i2c module. ChangeLog: v2: 2/2 - remove the hard coded interrupt trigger type. Bongsu Jeon (2): dt-bindings: net: nfc: s3fwrn5: Change I2C interrupt trigger to EDGE_RISING nfc: s3fwrn5: Remove hard coded interrupt trigger type from the i2c module ==================== Signed-off-by: -
Bongsu Jeon authored
For the flexible control of interrupt trigger type, remove the hard coded interrupt trigger type in the i2c module. The trigger type will be loaded from a dts. Signed-off-by:
Bongsu Jeon <bongsu.jeon@samsung.com> Signed-off-by:
-
Bongsu Jeon authored
Change interrupt trigger from IRQ_TYPE_LEVEL_HIGH to IRQ_TYPE_EDGE_RISING for stable NFC I2C interrupt handling. Samsung's NFC Firmware sends an i2c frame as below. 1. NFC Firmware sets the GPIO(interrupt pin) high when there is an i2c frame to send. 2. If the CPU's I2C master has received the i2c frame, NFC F/W sets the GPIO low. NFC driver's i2c interrupt handler would be called in the abnormal case as the NFC FW task of number 2 is delayed because of other high priority tasks. In that case, NFC driver will try to receive the i2c frame but there isn't any i2c frame to send in NFC. It would cause an I2C communication problem. This case would hardly happen. But, I changed the interrupt as a defense code. If Driver uses the TRIGGER_RISING instead of the LEVEL trigger, there would be no problem even if the NFC FW task is delayed. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
-
Zheng Yongjun authored
Replace a comma between expression statements by a semicolon. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
David S. Miller authored
Claudiu Beznea says: ==================== net: macb: add support for sama7g5 This series adds support for SAMA7G5 Ethernet interfaces: one 10/100Mbps and one 1Gbps interfaces. Along with it I also included a fix to disable clocks for SiFive FU540-C000 on failure path of fu540_c000_clk_init(). Thank you, Claudiu Beznea Changed in v3: - use clk_bulk_disable_unprepare in patch 3/8 - corrected clang compilation warning in patch 3/8 - revert changes in macb_clk_init() in patch 3/8 Changes in v2: - introduced patch "net: macb: add function to disable all macb clocks" and update patch "net: macb: unprepare clocks in case of failure" accordingly - collected tags ==================== Signed-off-by: -
Claudiu Beznea authored
Add support for SAMA7G5 10/100Mbps interface. Signed-off-by:
Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by:
-
Claudiu Beznea authored
Add support for SAMA7G5 gigabit ethernet interface. Signed-off-by:
-
Claudiu Beznea authored
Add documentation for SAMA7G5 gigabit ethernet interface. Signed-off-by:
-
Claudiu Beznea authored
Add documentation for SAMA7G5 ethernet interface. Signed-off-by:
-
Claudiu Beznea authored
Unprepare clocks in case of any failure in fu540_c000_clk_init(). Fixes: c218ad55 ("macb: Add support for SiFive FU540-C000") Signed-off-by:
-
Claudiu Beznea authored
Add function to disable all macb clocks. Signed-off-by:
-
Claudiu Beznea authored
SAMA7G5's ethernet IPs TX clock could be provided by its generic clock or by the external clock provided by the PHY. The internal IP logic divides properly this clock depending on the link speed. The patch adds a new capability so that macb_set_tx_clock() to not be called for IPs having this capability (the clock rate, in case of generic clock, is set at the boot time via device tree and the driver only enables it). Signed-off-by:
-
Claudiu Beznea authored
This is necessary for SAMA7G5 as it uses different values for PHY interface and also introduces hdfctlen bit. Signed-off-by:
-
- 09 Dec, 2020 2 commits
-
-
Pablo Neira Ayuso authored
- NET_ACT_CONNMARK and NET_ACT_CTINFO only require conntrack support. - NET_ACT_IPT only requires NETFILTER_XTABLES symbols, not IP_NF_IPTABLES. After this patch, NET_ACT_IPT becomes consistent with NET_EMATCH_IPT. NET_ACT_IPT dependency on IP_NF_IPTABLES predates Linux-2.6.12-rc2 (initial git repository build). Fixes: 22a5dc0e ("net: sched: Introduce connmark action") Fixes: 24ec483c ("net: sched: Introduce act_ctinfo action") Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Link: https://lore.kernel.org/r/20201208204707.11268-1-pablo@netfilter.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Shay Agroskin says: ==================== XDP Redirect implementation for ENA driver ENA is adding XDP Redirect support for its driver and some other small tweaks. This series adds the following: - Make log messages in the driver have a uniform format using netdev_* function - Improve code readability - Add support for XDP Redirect ==================== Link: https://lore.kernel.org/r/20201208180208.26111-1-shayagr@amazon.comSigned-off-by:
-
