- 15 Oct, 2021 11 commits
-
-
Richard Fitzgerald authored
The driver must free the IRQ in remove() to prevent the potential race where an IRQ starts to be handled while the driver is being removed but devres has not yet called free_irq(). However, the driver can run without an interrupt but devm_free_irq() will hit a WARN() if no devres-managed interrupt was ever created. Fix this by only attempting to create the interrupt handler if the hardware config specified an interrupt, and failing probe() if the interrupt could not be created. This means that in cs42l42_remove() an interrupt must have been registered if the irq number is valid and therefore it is safe to call devm_free_irq(). Signed-off-by:
Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20211015133619.4698-16-rf@opensource.cirrus.comSigned-off-by:
Mark Brown <broonie@kernel.org>
-
Richard Fitzgerald authored
OSC_SWITCH_STATUS is a volatile register indicating the current state of the clock switch logic. Signed-off-by:
-
Richard Fitzgerald authored
According to the datasheet the SRC MCLK must be as near as possible to (125 * sample rate). This means it should be ~6MHz for rates up to 48k and ~12MHz for rates above that. As per datasheet table 4-21. Signed-off-by:
-
Richard Fitzgerald authored
After enabling the HP or ADC by writing the corresponding PDN=0, it takes around 20 milliseconds for it to power up and the midrail supply to be stable. Add this wait into a DAPM widget callback. If HP and ADC are both powering up in a DAPM sequence, there's no need to do the wait twice. The widget will perform one wait in the POST_PMU if there was a PRE_PMU for one or both. Signed-off-by:
-
Richard Fitzgerald authored
It isn't possible to switch MCLK between 12MHz and 24MHz rate groups on-the-fly - this can only be done when cs42l42 is powered-down. All "normal" SCLK rates use an MCLK in the 12MHz group, so change the configs for SCLK > 12.288 MHz to use the PLL to generate an MCLK in the 12MHz group. As this means MCLK_DIV is always 0 it can be removed from the pll configuration setup. Signed-off-by:
-
Richard Fitzgerald authored
The driver currently only supports configuring for sample rates <= 96k and it isn't possible to setup a configuration that will support all sample rates up to 192k. For sample rates up to 96k MCLK is in the 12MHz group. However, although 192k only requires an I2S clock in the 12MHz group, the cs42l42 audio path is not natively 192k so the audio must be resampled. But for 192k the SRC requires a 24MHz MCLK. It is not possible to switch MCLK between 12MHz and 24MHz groups on-the-fly. The 12MHz group supports all sample rates up to 96k. Signed-off-by:
-
Richard Fitzgerald authored
The driver can run without an interrupt so if devm_request_threaded_irq() failed, the probe() just carried on. But if this was EPROBE_DEFER the driver would continue without an interrupt instead of deferring to wait for the interrupt to become available. Fixes: 2c394ca7 ("ASoC: Add support for CS42L42 codec") Signed-off-by:
-
Richard Fitzgerald authored
Volatile registers don't need a default value. Signed-off-by:
-
Richard Fitzgerald authored
Some registers had wrong default values in cs42l42_reg_defaults[]. Signed-off-by:
-
Richard Fitzgerald authored
An I2S frame always has two slots (left and right) even when sending mono. The right channel (channel 2) of ASP TX will always have the same bit width as the left channel and will always be on the high phase of LRCLK. The previous implementation always passed the field masks for both channels to snd_soc_component_update_bits() but for mono the written value only contained the settings for channel 1. The result was that for mono channel 2 was set to 8-bit (which is an invalid configuration) with both channels on the low phase of LRCLK. Signed-off-by:
-
Richard Fitzgerald authored
When capture and playback substreams are both running at the same time, cs42l42_pcm_hw_params() would be called for each direction. The first call will configure the PLL. The second call must not write the PLL configuration registers again if the first substream is already running, as this could destabilize the PLL. The DAI is marked symmetric sample bits and sample rate, so the two directions will always have the same SCLK (I2S always has 2 channel slots so the DAI does not need to require symmetric channels to guarantee the same SCLK). However, since cs42l42_pll_config() is checking for an active stream it may as well test that the requested SCLK is the same as the currently active configuration. Signed-off-by:
-
- 13 Oct, 2021 1 commit
-
-
Shengjiu Wang authored
There is a noise issue for 8kHz sample rate on slave mode. Compared with master mode, the difference is the DACDIV setting, after correcting the DACDIV, the noise is gone. There is no noise issue for 48kHz sample rate, because the default value of DACDIV is correct for 48kHz. So wm8960_configure_clocking() should be functional for ADC and DAC function even if it is slave mode. In order to be compatible for old use case, just add condition for checking that sysclk is zero with slave mode. Fixes: 0e50b51a ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock") Signed-off-by:
Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by:
-
- 12 Oct, 2021 1 commit
-
-
Stefan Binding authored
Ensure the default 0dB playback path is always used. The code that set FULL_SCALE_VOL based on LOAD_DET_RCSTAT was spurious, and resulted in a -6dB attenuation being accidentally inserted into the playback path. Signed-off-by:
Stefan Binding <sbinding@opensource.cirrus.com> Signed-off-by:
-
- 11 Oct, 2021 1 commit
-
-
Yang Yingliang authored
'component' is allocated in snd_soc_register_component(), but component->list is not initalized, this may cause snd_soc_del_component_unlocked() deref null ptr in the error handing case. KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] RIP: 0010:__list_del_entry_valid+0x81/0xf0 Call Trace: snd_soc_del_component_unlocked+0x69/0x1b0 [snd_soc_core] snd_soc_add_component.cold+0x54/0x6c [snd_soc_core] snd_soc_register_component+0x70/0x90 [snd_soc_core] devm_snd_soc_register_component+0x5e/0xd0 [snd_soc_core] tas2552_probe+0x265/0x320 [snd_soc_tas2552] ? tas2552_component_probe+0x1e0/0x1e0 [snd_soc_tas2552] i2c_device_probe+0xa31/0xbe0 Fix by adding INIT_LIST_HEAD() to snd_soc_component_initialize(). Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20211009065840.3196239-1-yangyingliang@huawei.comSigned-off-by:
-
- 07 Oct, 2021 7 commits
-
-
Srinivasa Rao Mandadapu authored
This patch fixes compilation error in wcd98x codec driver. Fixes: 04544222 ("ASoC: codecs: wcd938x: add audio routing and Kconfig") Signed-off-by:
Venkata Prasad Potturu <potturu@codeaurora.org> Signed-off-by:
Srinivasa Rao Mandadapu <srivasam@codeaurora.org> Reviewed-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/1633614675-27122-1-git-send-email-srivasam@codeaurora.orgSigned-off-by:
-
Takashi Iwai authored
The put callback of a kcontrol is supposed to return 1 when the value is changed, and this will be notified to user-space. However, some DAPM kcontrols always return 0 (except for errors), hence the user-space misses the update of a control value. This patch corrects the behavior by properly returning 1 when the value gets updated. Reported-and-tested-by:
Hans de Goede <hdegoede@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20211006141712.2439-1-tiwai@suse.deSigned-off-by:
-
Andy Shevchenko authored
dev_err_probe() avoids printing into log when the deferred probe is invoked. This is possible when clock provider is pending to appear. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211006150428.16434-4-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Andy Shevchenko authored
First of all, replace indexed API by plain one since we have index 0. Second, switch to optional variant and drop duplicated code. Signed-off-by:
-
Andy Shevchenko authored
Signed-off-by:
-
Andy Shevchenko authored
Access to platform data via dev_get_platdata() getter to make code cleaner. Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Acked-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.com> Link: https://lore.kernel.org/r/20211006150428.16434-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Srinivasa Rao Mandadapu authored
This patch is to fix audio 3.5mm jack detection failure on wcd938x codec based target. Fixes: bcee7ed0 (ASoC: codecs: wcd938x: add Multi Button Headset Control support) Signed-off-by:
-
- 30 Sep, 2021 1 commit
-
-
Hans de Goede authored
Commit 1d25684e ("ASoC: nau8824: Fix open coded prefix handling") replaced the nau8824_dapm_enable_pin() helper with direct calls to snd_soc_dapm_enable_pin(), but the helper was using snd_soc_dapm_force_enable_pin() and not forcing the MICBIAS + SAR supplies on breaks headphone vs headset and button-press detection. Replace the snd_soc_dapm_enable_pin() calls with snd_soc_dapm_force_enable_pin() to fix this. Cc: stable@vger.kernel.org Fixes: 1d25684e ("ASoC: nau8824: Fix open coded prefix handling") Signed-off-by:
-
- 27 Sep, 2021 2 commits
-
-
Mark Brown authored
Currently autoloading for SPI devices does not use the DT ID table, it uses SPI modalises. Supporting OF modalises is going to be difficult if not impractical, an attempt was made but has been reverted, so ensure that module autoloading works for this driver by adding SPI IDs for parts that only have a compatible listed. Fixes: 96c8395e ("spi: Revert modalias changes") Signed-off-by:
-
Mark Brown authored
Currently autoloading for SPI devices does not use the DT ID table, it uses SPI modalises. Supporting OF modalises is going to be difficult if not impractical, an attempt was made but has been reverted, so ensure that module autoloading works for this driver by adding SPI IDs for parts that only have a compatible listed. Fixes: 96c8395e ("spi: Revert modalias changes") Signed-off-by:
-
- 21 Sep, 2021 2 commits
-
-
Shengjiu Wang authored
With pause and resume test for ARC, there is occasionally channel swap issue. The reason is that currently driver set the DPATH out of reset first, then start the DMA, the first data got from FIFO may not be the Left channel. Moving DPATH out of reset operation after the dma enablement to fix this issue. Fixes: 28564486 ("ASoC: fsl_xcvr: Add XCVR ASoC CPU DAI driver") Signed-off-by:
-
Peter Rosin authored
Commit 25d27c4f ("ASoC: pcm512x: Add support for more data formats") breaks the TSE-850 device, which is using a pcm5142 in I2S and CBM_CFS mode (maybe not relevant). Without this fix, the result is: pcm512x 0-004c: Failed to set data format: -16 And after that, no sound. This fix is not 100% correct. The datasheet of at least the pcm5142 states that four bits (0xcc) in the I2S_1 register are "RSV" ("Reserved. Do not access.") and no hint is given as to what the initial values are supposed to be. So, specifying defaults for these bits is wrong. But perhaps better than a broken driver? Fixes: 25d27c4f ("ASoC: pcm512x: Add support for more data formats") Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Kirill Marinushkin <kmarinushkin@birdec.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Peter Rosin <peda@axentia.se> Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@gmail.com> Reviewed-by:
-
- 17 Sep, 2021 2 commits
-
-
Peter Ujfalusi authored
Do not print error message from snd_sof_trace_notify_for_error() when possible sleeping trace work is woken up to flush the remaining debug information. This action by itself is not an error, it is just an action we take when an error occurs to make sure that all information have been fed to the userspace (if we have trace in use). Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by:
-
Trevor Wu authored
S24_LE params fixup is only required for DPTX. Remove fixup ops assignment for HDMITX. Fixes: 40d605df ("ASoC: mediatek: mt8195: add machine driver with mt6359, rt1019 and rt5682") Signed-off-by:
Trevor Wu <trevor.wu@mediatek.com> Link: https://lore.kernel.org/r/20210917082805.30898-1-trevor.wu@mediatek.comSigned-off-by:
-
- 16 Sep, 2021 2 commits
-
-
Peter Ujfalusi authored
In case the firmware is missing we will have the following in the kernel log: 1 | Direct firmware load for intel/sof/sof-tgl-h.ri failed with error -2 2 | error: request firmware intel/sof/sof-tgl-h.ri failed err: -2 3 | you may need to download the firmware from https://github.com/thesofproject/sof-bin/ 4 | error: failed to load DSP firmware -2 5 | error: sof_probe_work failed err: -2 The first line is the standard, request_firmware() warning. The second and third line is printed in snd_sof_load_firmware_raw() Note that the first and second line is mostly identical. With this patch the log will be changed to: 1 | Direct firmware load for intel/sof/sof-tgl-h.ri failed with error -2 2 | error: sof firmware file is missing, you might need to 3 | download it from https://github.com/thesofproject/sof-bin/ 4 | error: failed to load DSP firmware -2 5 | error: sof_probe_work failed err: -2 Signed-off-by:
-
Marc Herbert authored
Invoke release_firmware() when the firmware fails to boot in sof_probe_continue(). The request_firmware() framework must be informed of failures in sof_probe_continue() otherwise its internal "batching" feature (different from caching) cached the firmware image forever. Attempts to correct the file in /lib/firmware/ were then silently and confusingly ignored until the next reboot. Unloading the drivers did not help because from their disconnected perspective the firmware had failed so there was nothing to release. Also leverage the new snd_sof_fw_unload() function to simplify the snd_sof_device_remove() function. Signed-off-by:
Marc Herbert <marc.herbert@intel.com> Reviewed-by:
Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com> Reviewed-by:
-
- 15 Sep, 2021 3 commits
-
-
Peter Ujfalusi authored
i.MX8 only uses SOF_FW_BLK_TYPE_IRAM (1) and SOF_FW_BLK_TYPE_SRAM (3) bars, everything else is left as 0 in sdev->bar[] array. If a broken or purposefully crafted firmware image is loaded with other types of FW_BLK_TYPE then a kernel crash can be triggered. Make sure that only IRAM/SRAM type is converted to bar index. Fixes: afb93d71 ("ASoC: SOF: imx: Add i.MX8M HW support") Signed-off-by:
Daniel Baluta <daniel.baluta@gmail.com> Reviewed-by:
-
Peter Ujfalusi authored
i.MX8 only uses SOF_FW_BLK_TYPE_IRAM (1) and SOF_FW_BLK_TYPE_SRAM (3) bars, everything else is left as 0 in sdev->bar[] array. If a broken or purposefully crafted firmware image is loaded with other types of FW_BLK_TYPE then a kernel crash can be triggered. Make sure that only IRAM/SRAM type is converted to bar index. Fixes: 202acc56 ("ASoC: SOF: imx: Add i.MX8 HW support") Signed-off-by:
-
Yong Zhi authored
Fix @buf arg given to hex_dump_to_buffer() and stack address used in dump error output. Fixes: e657c18a ('ASoC: SOF: Add xtensa support') Signed-off-by:
Yong Zhi <yong.zhi@intel.com> Reviewed-by:
-
- 10 Sep, 2021 7 commits
-
-
Mark Brown authored
Merge series "ASoC: fsl: register platform component before registering cpu dai" from Shengjiu Wang <shengjiu.wang@nxp.com>: There is no defer probe when adding platform component to snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime() snd_soc_register_card() -> snd_soc_bind_card() -> snd_soc_add_pcm_runtime() -> adding cpu dai -> adding codec dai -> adding platform component. So if the platform component is not ready at that time, then the sound card still registered successfully, but platform component is empty, the sound card can't be used. As there is defer probe checking for cpu dai component, then register platform component before cpu dai to avoid such issue. This patch set is to fix this issue for SAI, ESAI, MICFIL, SPDIF, XCVR drivers. Shengjiu Wang (5): ASoC: fsl_sai: register platform component before registering cpu dai ASoC: fsl_esai: register platform component before registering cpu dai ASoC: fsl_micfil: register platform component before registering cpu dai ASoC: fsl_spdif: register platform component before registering cpu dai ASoC: fsl_xcvr: register platform component before registering cpu dai sound/soc/fsl/fsl_esai.c | 16 ++++++++++------ sound/soc/fsl/fsl_micfil.c | 15 ++++++++++----- sound/soc/fsl/fsl_sai.c | 14 +++++++++----- sound/soc/fsl/fsl_spdif.c | 14 +++++++++----- sound/soc/fsl/fsl_xcvr.c | 15 ++++++++++----- 5 files changed, 48 insertions(+), 26 deletions(-) -- 2.17.1 -
Trevor Wu authored
When memory allocation for afe->reg_back_up fails, reg_back_up can't be used. Keep the suspend/resume flow but skip register backup when afe->reg_back_up is NULL, in case illegal memory access happens. Fixes: 283b6124 ("ASoC: mediatek: implement mediatek common structure") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20210910092613.30188-1-trevor.wu@mediatek.comSigned-off-by:
-
Shengjiu Wang authored
There is no defer probe when adding platform component to snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime() snd_soc_register_card() -> snd_soc_bind_card() -> snd_soc_add_pcm_runtime() -> adding cpu dai -> adding codec dai -> adding platform component. So if the platform component is not ready at that time, then the sound card still registered successfully, but platform component is empty, the sound card can't be used. As there is defer probe checking for cpu dai component, then register platform component before cpu dai to avoid such issue. Fixes: 28564486 ("ASoC: fsl_xcvr: Add XCVR ASoC CPU DAI driver") Signed-off-by: -
Shengjiu Wang authored
There is no defer probe when adding platform component to snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime() snd_soc_register_card() -> snd_soc_bind_card() -> snd_soc_add_pcm_runtime() -> adding cpu dai -> adding codec dai -> adding platform component. So if the platform component is not ready at that time, then the sound card still registered successfully, but platform component is empty, the sound card can't be used. As there is defer probe checking for cpu dai component, then register platform component before cpu dai to avoid such issue. Fixes: a2388a49 ("ASoC: fsl: Add S/PDIF CPU DAI driver") Signed-off-by: -
Shengjiu Wang authored
There is no defer probe when adding platform component to snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime() snd_soc_register_card() -> snd_soc_bind_card() -> snd_soc_add_pcm_runtime() -> adding cpu dai -> adding codec dai -> adding platform component. So if the platform component is not ready at that time, then the sound card still registered successfully, but platform component is empty, the sound card can't be used. As there is defer probe checking for cpu dai component, then register platform component before cpu dai to avoid such issue. Fixes: 47a70e6f ("ASoC: Add MICFIL SoC Digital Audio Interface driver.") Signed-off-by: -
Shengjiu Wang authored
There is no defer probe when adding platform component to snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime() snd_soc_register_card() -> snd_soc_bind_card() -> snd_soc_add_pcm_runtime() -> adding cpu dai -> adding codec dai -> adding platform component. So if the platform component is not ready at that time, then the sound card still registered successfully, but platform component is empty, the sound card can't be used. As there is defer probe checking for cpu dai component, then register platform component before cpu dai to avoid such issue. Fixes: 43d24e76 ("ASoC: fsl_esai: Add ESAI CPU DAI driver") Signed-off-by: -
Shengjiu Wang authored
There is no defer probe when adding platform component to snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime() snd_soc_register_card() -> snd_soc_bind_card() -> snd_soc_add_pcm_runtime() -> adding cpu dai -> adding codec dai -> adding platform component. So if the platform component is not ready at that time, then the sound card still registered successfully, but platform component is empty, the sound card can't be used. As there is defer probe checking for cpu dai component, then register platform component before cpu dai to avoid such issue. Fixes: 43550821 ("ASoC: Add SAI SoC Digital Audio Interface driver") Signed-off-by:
-
