- 11 Mar, 2018 5 commits
-
-
Hans de Goede authored
commit 1ba8f9d3 upstream. On some boards setting power_save to a non 0 value leads to clicking / popping sounds when ever we enter/leave powersaving mode. Ideally we would figure out how to avoid these sounds, but that is not always feasible. This commit adds a blacklist for devices where powersaving is known to cause problems and disables it on these devices. Note I tried to put this blacklist in userspace first: https://github.com/systemd/systemd/pull/8128 But the systemd maintainers rightfully pointed out that it would be impossible to then later remove entries once we actually find a way to make power-saving work on listed boards without issues. Having this list in the kernel will allow removal of the blacklist entry in the same commit which fixes the clicks / plops. The blacklist only applies to the default power_save module-option value, if a user explicitly sets the module-option then the blacklist is not used. [ added an ifdef CONFIG_PM for the build error -- tiwai] BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104 BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611 Cc: stable@vger.kernel.org Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Erik Veijola authored
commit 240a8af9 upstream. The capture interface doesn't work and the playback interface only supports 48 kHz sampling rate even though it advertises more rates. Signed-off-by:
Erik Veijola <erik.veijola@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Jeremy Boone authored
commit f9d4d9b5 upstream. Discrete TPMs are often connected over slow serial buses which, on some platforms, can have glitches causing bit flips. In all the driver _recv() functions, we need to use a u32 to unmarshal the response size, otherwise a bit flip of the 31st bit would cause the expected variable to go negative, which would then try to read a huge amount of data. Also sanity check that the expected amount of data is large enough for the TPM header. Signed-off-by:
Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by:
James Morris <james.morris@microsoft.com> Signed-off-by:
-
Jeremy Boone authored
commit 9b8cb28d upstream. Discrete TPMs are often connected over slow serial buses which, on some platforms, can have glitches causing bit flips. In all the driver _recv() functions, we need to use a u32 to unmarshal the response size, otherwise a bit flip of the 31st bit would cause the expected variable to go negative, which would then try to read a huge amount of data. Also sanity check that the expected amount of data is large enough for the TPM header. Signed-off-by:
-
Jeremy Boone authored
commit 6d24cd18 upstream. Discrete TPMs are often connected over slow serial buses which, on some platforms, can have glitches causing bit flips. In all the driver _recv() functions, we need to use a u32 to unmarshal the response size, otherwise a bit flip of the 31st bit would cause the expected variable to go negative, which would then try to read a huge amount of data. Also sanity check that the expected amount of data is large enough for the TPM header. Signed-off-by:
-
- 03 Mar, 2018 35 commits
-
-
Greg Kroah-Hartman authored
-
James Hogan authored
commit ebabcf17 upstream. GCC7 is a bit too eager to generate suboptimal __multi3 calls (128bit multiply with 128bit result) for MIPS64r6 builds, even in code which doesn't explicitly use 128bit types, such as the following: unsigned long func(unsigned long a, unsigned long b) { return a > (~0UL) / b; } Which GCC rearanges to: return (unsigned __int128)a * (unsigned __int128)b > 0xffffffffffffffff; Therefore implement __multi3, but only for MIPS64r6 with GCC7 as under normal circumstances we wouldn't expect any calls to __multi3 to be generated from kernel code. Reported-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
James Hogan <jhogan@kernel.org> Tested-by:
Waldemar Brodkorb <wbx@openadk.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Maciej W. Rozycki <macro@mips.com> Cc: Matthew Fortune <matthew.fortune@mips.com> Cc: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17890/ Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Yangbo Lu authored
[ Upstream commit 11d827a9 ] set_fipers() calling should be protected by spinlock in case that any interrupt breaks related registers setting and the function we expect. This patch is to move set_fipers() to spinlock protecting area in ptp_gianfar_adjtime(). Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Reviewed-by:
Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <alexander.levin@microsoft.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit c76f97c9 ] Some sockopt handling functions were calculating the length of the buffer to be written to userspace and then calculating it again when actually writing the buffer, which could lead to some write not using an up-to-date length. This patch updates such places to just make use of the len variable. Also, replace some sizeof(type) to sizeof(var). Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit cf2acf66 ] When cleaning up after a partially successful gntdev_mmap(), unmap the successfully mapped grant pages otherwise Xen will kill the domain if in debug mode (Attempt to implicitly unmap a granted PTE) or Linux will kill the process and emit "BUG: Bad page map in process" if Xen is in release mode. This is only needed when use_ptemod is true because gntdev_put_map() will unmap grant pages itself when use_ptemod is false. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit 951a0102 ] If the requested range has a hole, the calculation of the number of pages to unmap is off by one. Fix it. Signed-off-by:
-
Sergei Shtylyov authored
[ Upstream commit 195e2add ] The 'sh_eth' driver's probe() method would fail on the SolutionEngine7710 board and crash on SolutionEngine7712 board as the platform code is hopelessly behind the driver's platform data -- it passes the PHY address instead of 'struct sh_eth_plat_data *'; pass the latter to the driver in order to fix the bug... Fixes: 71557a37 ("[netdrvr] sh_eth: Add SH7619 support") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 56c02902 ] If the probing of the regulator is deferred, the memory allocated by 'mdiobus_alloc_size()' will be leaking. It should be freed before the next call to 'sun4i_mdio_probe()' which will reallocate it. Fixes: 4bdcb1dd ("net: Add MDIO bus driver for the Allwinner EMAC") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Eduardo Otubo authored
[ Upstream commit b707fda2 ] When loading the module after unloading it, the network interface would not be enabled and thus wouldn't have a backend counterpart and unable to be used by the guest. The guest would face errors like: [root@guest ~]# ethtool -i eth0 Cannot get driver information: No such device [root@guest ~]# ifconfig eth0 eth0: error fetching interface information: Device not found This patch initializes the state of the netfront device whenever it is loaded manually, this state would communicate the netback to create its device and establish the connection between them. Signed-off-by:
Eduardo Otubo <otubo@redhat.com> Reviewed-by:
-
Venkat Duvvuru authored
[ Upstream commit 78f30004 ] In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a check for "Invalid VF id". Currently, the check is done against max_vfs. However, the user doesn't always create max_vfs. So, the check should be against the created number of VFs. The number of bnxt_vf_info structures that are allocated in bnxt_alloc_vf_resources routine is the "number of requested VFs". So, if an "invalid VF id" falls between the requested number of VFs and the max_vfs, the driver will be dereferencing an invalid pointer. Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by:
Venkat Devvuru <venkatkumar.duvvuru@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Luu An Phu authored
[ Upstream commit 13454c14 ] The flexcan_start_xmit() function compares the frame length with data register length to write frame content into data[0] and data[1] register. Data register length is 4 bytes and frame maximum length is 8 bytes. Fix the check that compares frame length with 3. Because the register length is 4. Signed-off-by:
Luu An Phu <phu.luuan@nxp.com> Reviewed-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Johannes Berg authored
[ Upstream commit 736a80bb ] If there are multiple mesh stations with the same MAC address, they will both get confused and start throwing warnings. Obviously in this case nothing can actually work anyway, so just drop frames that look like they're from ourselves early on. Reported-by:
Gui Iribarren <gui@altermundi.net> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Xiongwei Song authored
[ Upstream commit 19d859a7 ] In the function ttm_page_alloc_init, kzalloc call is made for variable _manager, we need to check its return value, it may return NULL. Signed-off-by:
Xiongwei Song <sxwjean@gmail.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Tushar Dave authored
[ Upstream commit 0b76aae7 ] This patch adds check so that driver does not disable already disabled device. [ 44.637743] advantechwdt: Unexpected close, not stopping watchdog! [ 44.997548] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6 [ 45.013419] e1000 0000:00:03.0: disabling already-disabled device [ 45.013447] ------------[ cut here ]------------ [ 45.014868] WARNING: CPU: 1 PID: 71 at drivers/pci/pci.c:1641 pci_disable_device+0xa1/0x105: pci_disable_device at drivers/pci/pci.c:1640 [ 45.016171] CPU: 1 PID: 71 Comm: rcu_perf_shutdo Not tainted 4.14.0-01330-g3c073991 #1 [ 45.017197] task: ffff88011bee9e40 task.stack: ffffc90000860000 [ 45.017987] RIP: 0010:pci_disable_device+0xa1/0x105: pci_disable_device at drivers/pci/pci.c:1640 [ 45.018603] RSP: 0000:ffffc90000863e30 EFLAGS: 00010286 [ 45.019282] RAX: 0000000000000035 RBX: ffff88013a230008 RCX: 0000000000000000 [ 45.020182] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000203 [ 45.021084] RBP: ffff88013a3f31e8 R08: 0000000000000001 R09: 0000000000000000 [ 45.021986] R10: ffffffff827ec29c R11: 0000000000000002 R12: 0000000000000001 [ 45.022946] R13: ffff88013a230008 R14: ffff880117802b20 R15: ffffc90000863e8f [ 45.023842] FS: 0000000000000000(0000) GS:ffff88013fd00000(0000) knlGS:0000000000000000 [ 45.024863] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 45.025583] CR2: ffffc900006d4000 CR3: 000000000220f000 CR4: 00000000000006a0 [ 45.026478] Call Trace: [ 45.026811] __e1000_shutdown+0x1d4/0x1e2: __e1000_shutdown at drivers/net/ethernet/intel/e1000/e1000_main.c:5162 [ 45.027344] ? rcu_perf_cleanup+0x2a1/0x2a1: rcu_perf_shutdown at kernel/rcu/rcuperf.c:627 [ 45.027883] e1000_shutdown+0x14/0x3a: e1000_shutdown at drivers/net/ethernet/intel/e1000/e1000_main.c:5235 [ 45.028351] device_shutdown+0x110/0x1aa: device_shutdown at drivers/base/core.c:2807 [ 45.028858] kernel_power_off+0x31/0x64: kernel_power_off at kernel/reboot.c:260 [ 45.029343] rcu_perf_shutdown+0x9b/0xa7: rcu_perf_shutdown at kernel/rcu/rcuperf.c:637 [ 45.029852] ? __wake_up_common_lock+0xa2/0xa2: autoremove_wake_function at kernel/sched/wait.c:376 [ 45.030414] kthread+0x126/0x12e: kthread at kernel/kthread.c:233 [ 45.030834] ? __kthread_bind_mask+0x8e/0x8e: kthread at kernel/kthread.c:190 [ 45.031399] ? ret_from_fork+0x1f/0x30: ret_from_fork at arch/x86/entry/entry_64.S:443 [ 45.031883] ? kernel_init+0xa/0xf5: kernel_init at init/main.c:997 [ 45.032325] ret_from_fork+0x1f/0x30: ret_from_fork at arch/x86/entry/entry_64.S:443 [ 45.032777] Code: 00 48 85 ed 75 07 48 8b ab a8 00 00 00 48 8d bb 98 00 00 00 e8 aa d1 11 00 48 89 ea 48 89 c6 48 c7 c7 d8 e4 0b 82 e8 55 7d da ff <0f> ff b9 01 00 00 00 31 d2 be 01 00 00 00 48 c7 c7 f0 b1 61 82 [ 45.035222] ---[ end trace c257137b1b1976ef ]--- [ 45.037838] ACPI: Preparing to enter system sleep state S5 Signed-off-by:
Tushar Dave <tushar.n.dave@oracle.com> Tested-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Aliaksei Karaliou authored
[ Upstream commit 3a3882ff ] xfs_qm_init_quotainfo() does not check result of register_shrinker() which was tagged as __must_check recently, reported by sparse. Signed-off-by:
Aliaksei Karaliou <akaraliou.dev@gmail.com> [darrick: move xfs_qm_destroy_quotainos nearer xfs_qm_init_quotainos] Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Aliaksei Karaliou authored
[ Upstream commit 21968815 ] xfs_qm_destroy_quotainfo() does not destroy quotainfo->qi_tree_lock while destroys quotainfo->qi_quotaofflock. Signed-off-by:
-
Erez Shitrit authored
[ Upstream commit 16ba3def ] When using enhanced mode for IPoIB, two threads may execute xmit in parallel to two different TX queues while the target is the same. In this case, both of them will add the same neighbor to the path's neigh link list and we might see the following message: list_add double add: new=ffff88024767a348, prev=ffff88024767a348... WARNING: lib/list_debug.c:31__list_add_valid+0x4e/0x70 ipoib_start_xmit+0x477/0x680 [ib_ipoib] dev_hard_start_xmit+0xb9/0x3e0 sch_direct_xmit+0xf9/0x250 __qdisc_run+0x176/0x5d0 __dev_queue_xmit+0x1f5/0xb10 __dev_queue_xmit+0x55/0xb10 Analysis: Two SKB are scheduled to be transmitted from two cores. In ipoib_start_xmit, both gets NULL when calling ipoib_neigh_get. Two calls to neigh_add_path are made. One thread takes the spin-lock and calls ipoib_neigh_alloc which creates the neigh structure, then (after the __path_find) the neigh is added to the path's neigh link list. When the second thread enters the critical section it also calls ipoib_neigh_alloc but in this case it gets the already allocated ipoib_neigh structure, which is already linked to the path's neigh link list and adds it again to the list. Which beside of triggering the list, it creates a loop in the linked list. This loop leads to endless loop inside path_rec_completion. Solution: Check list_empty(&neigh->list) before adding to the list. Add a similar fix in "ipoib_multicast.c::ipoib_mcast_send" Fixes: b63b70d8 ('IPoIB: Use a private hash table for path lookup in xmit path') Signed-off-by:
Erez Shitrit <erezsh@mellanox.com> Reviewed-by:
Alex Vesker <valex@mellanox.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Leon Romanovsky authored
[ Upstream commit 5a371cf8 ] ibmr.device is being set only after ib_alloc_mr() is successfully complete. Therefore, in case imlx4_mr_enable() returns with error, the error flow unwinder calls to mlx4_free_priv_pages(), which uses ibmr.device. Such usage causes to NULL dereference oops and to fix it, the IB device should be set in the mr struct earlier stage (e.g. prior to calling mlx4_free_priv_pages()). Fixes: 1b2cd0fc ("IB/mlx4: Support the new memory registration API") Signed-off-by:
Nitzan Carmi <nitzanc@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
-
Stefan Haberland authored
[ Upstream commit 8a9bd4f8 ] We store per path and per device configuration data to identify the path or device correctly. The per path configuration data might get mixed up if the original request gets into error recovery and is started with a random path mask. This would lead to a wrong identification of a path in case of a CUIR event for example. Fix by copying the path mask from the original request to the error recovery request in case it is a path verification request. Signed-off-by:
Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by:
Jan Hoeppner <hoeppner@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Matthieu CASTET authored
[ Upstream commit 2b83ff96 ] With the current code, the following sequence won't work : echo timer > trigger echo 0 > delay_off * at this point we call ** led_delay_off_store ** led_blink_set
-
Guilherme G. Piccoli authored
[ Upstream commit f7084059 ] While in recovery process of PCI error (called EEH on PowerPC arch), another PCI transaction could be corrupted causing a situation of nested PCI errors. Also, this scenario could be reproduced with error injection mechanisms (for debug purposes). We observe that in case of nested PCI errors, bnx2x might attempt to initialize its shmem and cause a kernel crash due to bad addresses read from MCP. Multiple different stack traces were observed depending on the point the second PCI error happens. This patch avoids the crashes by: * failing PCI recovery in case of nested errors (since multiple PCI errors in a row are not expected to lead to a functional adapter anyway), and by, * preventing access to adapter FW when MCP is failed (we mark it as failed when shmem cannot get initialized properly). Reported-by:
Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by:
Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by:
Shahed Shaikh <Shahed.Shaikh@cavium.com> Signed-off-by:
-
Siva Reddy Kallam authored
[ Upstream commit e60ee41a ] A customer noticed RX path hang when MTU is changed on the fly while running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720 belongs to same ASIC family, we observed same issue and same fix could solve this problem for 5720. Signed-off-by:
Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by:
-
Siva Reddy Kallam authored
[ Upstream commit 4419bb1c ] One of AMD based server with 5762 hangs with jumbo frame traffic. This AMD platform has southbridge limitation which is restricting MRRS to 4000. As a work around, driver to restricts the MRRS to 2048 for this particular 5762 NX1 card. Signed-off-by:
-
James Hogan authored
[ Upstream commit bbc25bee ] Current MIPS64r6 toolchains aren't able to generate efficient DMULU/DMUHU based code for the C implementation of umul_ppmm(), which performs an unsigned 64 x 64 bit multiply and returns the upper and lower 64-bit halves of the 128-bit result. Instead it widens the 64-bit inputs to 128-bits and emits a __multi3 intrinsic call to perform a 128 x 128 multiply. This is both inefficient, and it results in a link error since we don't include __multi3 in MIPS linux. For example commit 90a53e44 ("cfg80211: implement regdb signature checking") merged in v4.15-rc1 recently broke the 64r6_defconfig and 64r6el_defconfig builds by indirectly selecting MPILIB. The same build errors can be reproduced on older kernels by enabling e.g. CRYPTO_RSA: lib/mpi/generic_mpih-mul1.o: In function `mpihelp_mul_1': lib/mpi/generic_mpih-mul1.c:50: undefined reference to `__multi3' lib/mpi/generic_mpih-mul2.o: In function `mpihelp_addmul_1': lib/mpi/generic_mpih-mul2.c:49: undefined reference to `__multi3' lib/mpi/generic_mpih-mul3.o: In function `mpihelp_submul_1': lib/mpi/generic_mpih-mul3.c:49: undefined reference to `__multi3' lib/mpi/mpih-div.o In function `mpihelp_divrem': lib/mpi/mpih-div.c:205: undefined reference to `__multi3' lib/mpi/mpih-div.c:142: undefined reference to `__multi3' Therefore add an efficient MIPS64r6 implementation of umul_ppmm() using inline assembly and the DMULU/DMUHU instructions, to prevent __multi3 calls being emitted. Fixes: 7fd08ca5 ("MIPS: Add build support for the MIPS R6 ISA") Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 506e8a91 ] dtc warns about two 'clocks' properties that have an extraneous '1' at the end: arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1]) Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1]) The clocks that get referenced here are fixed-rate, so they do not take any argument, and dtc interprets the next cell as a phandle, which is invalid. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Cathy Avery authored
[ Upstream commit d1b8b239 ] When an I/O is returned with an srb_status of SRB_STATUS_INVALID_LUN which has zero good_bytes it must be assigned an error. Otherwise the I/O will be continuously requeued and will cause a deadlock in the case where disks are being hot added and removed. sd_probe_async will wait forever for its I/O to complete while holding scsi_sd_probe_domain. Also returning the default error of DID_TARGET_FAILURE causes multipath to not retry the I/O resulting in applications receiving I/O errors before a failover can occur. Signed-off-by:
Cathy Avery <cavery@redhat.com> Signed-off-by:
Long Li <longli@microsoft.com> Reviewed-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Alexander Kochetkov authored
[ Upstream commit e688822d ] arc_emac_rx() has some issues found by code review. In case netdev_alloc_skb_ip_align() or dma_map_single() failure rx fifo entry will not be returned to EMAC. In case dma_map_single() failure previously allocated skb became lost to driver. At the same time address of newly allocated skb will not be provided to EMAC. Signed-off-by:
Alexander Kochetkov <al.kochet@gmail.com> Signed-off-by:
-
Radu Pirea authored
[ Upstream commit 66e900a3 ] The only part of atmel_spi_remove which needs to be atomic is hardware reset. atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts enabled. atmel_spi_release_dma calls dma_release_channel and dma_release_channel locks a mutex inside of spin_lock. So the call of these functions can't be inside a spin_lock. Reported-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
Radu Pirea <radu.pirea@microchip.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Karol Herbst authored
[ Upstream commit a121027d ] On my GP107 when I load nouveau after unloading it, for some reason the GPU stopped sending or the CPU stopped receiving interrupts if MSI was enabled. Doing a rearm once before getting any interrupts fixes this. Signed-off-by:
Karol Herbst <kherbst@redhat.com> Reviewed-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Al Viro authored
[ Upstream commit 9ee332d9 ] Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Chunyan Zhang authored
[ Upstream commit 36b0cb84 ] An additional 'ip' will be pushed to the stack, for restoring the DACR later, if CONFIG_CPU_SW_DOMAIN_PAN defined. However, the fixup still get the err_ptr by add #8*4 to sp, which results in the fact that the code area pointed by the LR will be overwritten, or the kernel will crash if CONFIG_DEBUG_RODATA is enabled. This patch fixes the stack mismatch. Fixes: a5e090ac ("ARM: software-based priviledged-no-access support") Signed-off-by:
Lvqiang Huang <Lvqiang.Huang@spreadtrum.com> Signed-off-by:
Chunyan Zhang <zhang.lyra@gmail.com> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Brendan McGrath authored
[ Upstream commit 588753f1 ] One example of when an ICMPv6 packet is required to be looped back is when a host acts as both a Multicast Listener and a Multicast Router. A Multicast Router will listen on address ff02::16 for MLDv2 messages. Currently, MLDv2 messages originating from a Multicast Listener running on the same host as the Multicast Router are not being delivered to the Multicast Router. This is due to dst.input being assigned the default value of dst_discard. This results in the packet being looped back but discarded before being delivered to the Multicast Router. This patch sets dst.input to ip6_input to ensure a looped back packet is delivered to the Multicast Router. Signed-off-by:
Brendan McGrath <redmcg@redmandi.dyndns.org> Signed-off-by:
-
Sascha Hauer authored
[ Upstream commit fdf2e821 ] When erased subpages are read then the BCH decoder returns STATUS_ERASED if they are all empty, or STATUS_UNCORRECTABLE if there are bitflips. When there are bitflips, we have to set these bits again to show the upper layers a completely erased page. When a bitflip happens in the exact byte where the bad block marker is, then this byte is swapped with another byte in block_mark_swapping(). The correction code then detects a bitflip in another subpage and no longer corrects the bitflip where it really happens. Correct this behaviour by calling block_mark_swapping() after the bitflips have been corrected. In our case UBIFS failed with this bug because it expects erased pages to be really empty: UBIFS error (pid 187): ubifs_scan: corrupt empty space at LEB 36:118735 UBIFS error (pid 187): ubifs_scanned_corruption: corruption at LEB 36:118735 UBIFS error (pid 187): ubifs_scanned_corruption: first 8192 bytes from LEB 36:118735 UBIFS error (pid 187): ubifs_scan: LEB 36 scanning failed UBIFS error (pid 187): do_commit: commit failed, error -117 Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by:
Richard Weinberger <richard@nod.at> Acked-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Yunlei He authored
commit dad48e73 upstream. Thread A: Thread B: -f2fs_remount -sbi->mount_opt.opt = 0; <--- -f2fs_iget -do_read_inode -f2fs_init_extent_tree -F2FS_I(inode)->extent_tree is NULL -default_options && parse_options -remount return <--- -f2fs_map_blocks -f2fs_lookup_extent_tree -f2fs_bug_on(sbi, !et); The same problem with f2fs_new_inode. Signed-off-by:
Yunlei He <heyunlei@huawei.com> Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
Nikolay Borisov <nborisov@suse.com> Signed-off-by:
-
Anna-Maria Gleixner authored
commit 48d0c9be upstream. The POSIX specification defines that relative CLOCK_REALTIME timers are not affected by clock modifications. Those timers have to use CLOCK_MONOTONIC to ensure POSIX compliance. The introduction of the additional HRTIMER_MODE_PINNED mode broke this requirement for pinned timers. There is no user space visible impact because user space timers are not using pinned mode, but for consistency reasons this needs to be fixed. Check whether the mode has the HRTIMER_MODE_REL bit set instead of comparing with HRTIMER_MODE_ABS. Signed-off-by:
Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Christoph Hellwig <hch@lst.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: keescook@chromium.org Fixes: 597d0275 ("timers: Framework for identifying pinned timers") Link: http://lkml.kernel.org/r/20171221104205.7269-7-anna-maria@linutronix.deSigned-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Mike Galbraith <efault@gmx.de> Signed-off-by:
-
