Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.

To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking
notifier chain. Dispatch to mlxsw_sp_port_obj_add() resp. _del() to
maintain the behavior that the switchdev operation based code currently
has. Defer to switchdev_handle_port_obj_add() / _del() to handle the
recursive descend, because mlxsw supports a number of upper types.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the transition from switchdev operations to notifier chain (which
will take place in following patches), the onus is on the driver to find
its own devices below possible layer of LAG or other uppers.

The logic to do so is fairly repetitive: each driver is looking for its
own devices among the lowers of the notified device. For those that it
finds, it calls a handler. To indicate that the event was handled,
struct switchdev_notifier_port_obj_info.handled is set. The differences
lie only in what constitutes an "own" device and what handler to call.

Therefore abstract this logic into two helpers,
switchdev_handle_port_obj_add() and switchdev_handle_port_obj_del(). If
a driver only supports physical ports under a bridge device, it will
simply avoid this layer of indirection.

One area where this helper diverges from the current switchdev behavior
is the case of mixed lowers, some of which are switchdev ports and some
of which are not. Previously, such scenario would fail with -EOPNOTSUPP.
The helper could do that for lowers for which the passed-in predicate
doesn't hold. That would however break the case that switchdev ports
from several different drivers are stashed under one master, a scenario
that switchdev currently happily supports. Therefore tolerate any and
all unknown netdevices, whether they are backed by a switchdev driver
or not.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.

ethsw currently doesn't support any uppers other than bridge.
SWITCHDEV_OBJ_ID_HOST_MDB and _PORT_MDB objects are always notified on
the bridge port device. Thus the only case that a stacked device could
be validly referenced by port object notifications are bridge
notifications for VLAN objects added to the bridge itself. But the
driver explicitly rejects such notifications in port_vlans_add(). It is
therefore safe to assume that the only interesting case is that the
notification is on a front-panel port netdevice.

To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking
notifier chain. Dispatch to swdev_port_obj_add() resp. _del() to
maintain the behavior that the switchdev operation based code currently
has.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethsw currently uses an open-coded comparison of netdev_ops to determine
whether whether a device represents a front panel port. Wrap this into a
named function to simplify reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.

DSA currently doesn't support any other uppers than bridge.
SWITCHDEV_OBJ_ID_HOST_MDB and _PORT_MDB objects are always notified on
the bridge port device. Thus the only case that a stacked device could
be validly referenced by port object notifications are bridge
notifications for VLAN objects added to the bridge itself. But the
driver explicitly rejects such notifications in dsa_port_vlan_add(). It
is therefore safe to assume that the only interesting case is that the
notification is on a front-panel port netdevice. Therefore keep the
filtering by dsa_slave_dev_check() in place.

To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking
notifier chain. Dispatch to rocker_port_obj_add() resp. _del() to
maintain the behavior that the switchdev operation based code currently
has.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.

rocker currently doesn't support any uppers other than bridge. Thus the
only case that a stacked device could be validly referenced by port
object notifications are bridge notifications for VLAN objects added to
the bridge itself. But the driver explicitly rejects such notifications
in rocker_world_port_obj_vlan_add(). It is therefore safe to assume that
the only interesting case is that the notification is on a front-panel
port netdevice.

Subscribe to the blocking notifier chain. In the handler, filter out
notifications on any foreign netdevices. Dispatch the new notifiers to
rocker_port_obj_add() resp. _del() to maintain the behavior that the
switchdev operation based code currently has.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An offloading driver may need to have access to switchdev events on
ports that aren't directly under its control. An example is a VXLAN port
attached to a bridge offloaded by a driver. The driver needs to know
about VLANs configured on the VXLAN device. However the VXLAN device
isn't stashed between the bridge and a front-panel-port device (such as
is the case e.g. for LAG devices), so the usual switchdev ops don't
reach the driver.

VXLAN is likely not the only device type like this: in theory any L2
tunnel device that needs offloading will prompt requirement of this
sort. This falsifies the assumption that only the lower devices of a
front panel port need to be notified to achieve flawless offloading.

A way to fix this is to give up the notion of port object addition /
deletion as a switchdev operation, which assumes somewhat tight coupling
between the message producer and consumer. And instead send the message
over a notifier chain.

To that end, introduce two new switchdev notifier types,
SWITCHDEV_PORT_OBJ_ADD and SWITCHDEV_PORT_OBJ_DEL. These notifier types
communicate the same event as the corresponding switchdev op, except in
a form of a notification. struct switchdev_notifier_port_obj_info was
added to carry the fields that the switchdev op carries. An additional
field, handled, will be used to communicate back to switchdev that the
event has reached an interested party, which will be important for the
two-phase commit.

The two switchdev operations themselves are kept in place. Following
patches first convert individual clients to the notifier protocol, and
only then are the operations removed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In general one can't assume that a switchdev notifier is called in a
non-atomic context, and correspondingly, the switchdev notifier chain is
an atomic one.

However, port object addition and deletion messages are delivered from a
process context. Even the MDB addition messages, whose delivery is
scheduled from atomic context, are queued and the delivery itself takes
place in blocking context. For VLAN messages in particular, keeping the
blocking nature is important for error reporting.

Therefore introduce a blocking notifier chain and related service
functions to distribute the notifications for which a blocking context
can be assumed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The two macros SWITCHDEV_OBJ_PORT_VLAN() and SWITCHDEV_OBJ_PORT_MDB()
expand to a container_of() call, yielding an appropriate container of
their sole argument. However, due to a name collision, the first
argument, i.e. the contained object pointer, is not the only one to get
expanded. The third argument, which is a structure member name, and
should be kept literal, gets expanded as well. The only safe way to use
these two macros is therefore to name the local variable passed to them
"obj".

To fix this, rename the sole argument of the two macros from
"obj" (which collides with the member name) to "OBJ". Additionally,
instead of passing "OBJ" to container_of() verbatim, parenthesize it, so
that a comma in the passed-in expression doesn't pollute the
container_of() invocation.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: some functional improvements

This series includes a few functional improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace macro TX_FRAGS_READY_FOR with function rtl_tx_slots_avail
to make code cleaner and type-safe.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use napi_consume_skb() where possible to profit from
bulk free infrastructure.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the GMII chip versions we set the version number which was set
already. This can be simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even the chip versions within a family have so many differences that
using a default chip version doesn't really make sense. Instead
of leaving a best case flaky network connectivity, bail out and
report the unknown chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove ancient GCC bug workaround in a second place and factor out
rtl_8169_get_txd_opts1.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
net: hns3: Adds support of debugfs to HNS3 driver

This patchset adds support of debugfs to the HNS3 driver.

Support has been added to query info related to below items:
1. Queue related ("echo queue info [queue no] > cmd")
2. Flow Director ("echo dump fd tcam > cmd")
3. TC config ("echo dump tc > cmd")
4. Transmit Module/Scheduler ("echo dump tm > cmd")
5. QoS pause ("echo dump qos pause cfg > cmd")
6. QoS buffer ("echo dump qos pri map > cmd")
7. QoS prio map ("echo dump qos buf cfg > cmd")

NOTE: Above commands are *read-only* and are only intended to
query the information from the SoC(and dump inside the kernel,
for now) and in no way tries to perform write operations for
the purpose of configuration etc.

Change Log
----------
V1-->V2:
   * Addressed the comments provided by Jakub Kicinski.
     1. Removed the .rej files mistakenly made part of Flow Director patch.
        Link: https://lkml.org/lkml/2018/11/20/249
     2. Added command summary in the cover letter
        Link: https://lkml.org/lkml/2018/11/22/1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch prints qos buffer config information.

debugfs command:
echo dump qos buf cfg > cmd

Sample Command:
root@(none)# echo dump qos buf cfg > cmd
hns3 0000:7d:00.0: dump qos buf cfg
hns3 0000:7d:00.0: tx_packet_buf_tc_0: 0x1aa
hns3 0000:7d:00.0: tx_packet_buf_tc_1: 0x0
hns3 0000:7d:00.0: tx_packet_buf_tc_2: 0x0
hns3 0000:7d:00.0: tx_packet_buf_tc_3: 0x0
hns3 0000:7d:00.0: tx_packet_buf_tc_4: 0x0
hns3 0000:7d:00.0: tx_packet_buf_tc_5: 0x0
hns3 0000:7d:00.0: tx_packet_buf_tc_6: 0x0
hns3 0000:7d:00.0: tx_packet_buf_tc_7: 0x0
hns3 0000:7d:00.0:
hns3 0000:7d:00.0: rx_packet_buf_tc_0: 0x130
hns3 0000:7d:00.0: rx_packet_buf_tc_1: 0x0
hns3 0000:7d:00.0: rx_packet_buf_tc_2: 0x0
hns3 0000:7d:00.0: rx_packet_buf_tc_3: 0x0
hns3 0000:7d:00.0: rx_packet_buf_tc_4: 0x0
hns3 0000:7d:00.0: rx_packet_buf_tc_5: 0x0
hns3 0000:7d:00.0: rx_packet_buf_tc_6: 0x0
hns3 0000:7d:00.0: rx_packet_buf_tc_7: 0x0
hns3 0000:7d:00.0: rx_share_buf: 0x1e0e
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch prints qos priority map information.

debugfs command:
echo dump qos pri map > cmd

Sample Command:
root@(none)# echo dump qos pri map > cmd
hns3 0000:7d:00.0: dump qos pri map
hns3 0000:7d:00.0: vlan_to_pri: 0x0
hns3 0000:7d:00.0: pri_0_to_tc: 0x0
hns3 0000:7d:00.0: pri_1_to_tc: 0x0
hns3 0000:7d:00.0: pri_2_to_tc: 0x0
hns3 0000:7d:00.0: pri_3_to_tc: 0x0
hns3 0000:7d:00.0: pri_4_to_tc: 0x0
hns3 0000:7d:00.0: pri_5_to_tc: 0x0
hns3 0000:7d:00.0: pri_6_to_tc: 0x0
hns3 0000:7d:00.0: pri_7_to_tc: 0x0
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch prints qos pause config information.

debugfs command:
echo dump qos pause cfg > cmd

Sample Command:
root@(none)# echo dump qos pause cfg > cmd
hns3 0000:7d:00.0: dump qos pause cfg
hns3 0000:7d:00.0: pause_trans_gap: 0xff
hns3 0000:7d:00.0: pause_trans_time: 0xffff
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch prints Transmit Module's Traffic sched
related config information.

debugfs command:
echo dump tm > cmd

Sample output:
root@(none)# echo dump tm > cmd
hns3 0000:7d:00.0: dump tm
hns3 0000:7d:00.0: PG_TO_PRI gp_id: 0
hns3 0000:7d:00.0: PG_TO_PRI map: 0x1
hns3 0000:7d:00.0: QS_TO_PRI qs_id: 0
hns3 0000:7d:00.0: QS_TO_PRI priority: 0
hns3 0000:7d:00.0: QS_TO_PRI link_vld: 1
hns3 0000:7d:00.0: NQ_TO_QS nq_id: 0
hns3 0000:7d:00.0: NQ_TO_QS qset_id: 1024
hns3 0000:7d:00.0: PG pg_id: 0
hns3 0000:7d:00.0: PG dwrr: 100
hns3 0000:7d:00.0: QS qs_id: 0
hns3 0000:7d:00.0: QS dwrr: 100
hns3 0000:7d:00.0: PRI pri_id: 0
hns3 0000:7d:00.0: PRI dwrr: 100
hns3 0000:7d:00.0: PRI_C pri_id: 0
hns3 0000:7d:00.0: PRI_C pri_shapping: 0x2850000
hns3 0000:7d:00.0: PRI_P pri_id: 0
hns3 0000:7d:00.0: PRI_P pri_shapping: 0x2850796
hns3 0000:7d:00.0: PG_C pg_id: 0
hns3 0000:7d:00.0: PG_C pg_shapping: 0x2850000
hns3 0000:7d:00.0: PG_P pg_id: 0
hns3 0000:7d:00.0: PG_P pg_shapping: 0x2850496
hns3 0000:7d:00.0: PORT port_shapping: 0x2850296
hns3 0000:7d:00.0: PG_SCH pg_id: 0
hns3 0000:7d:00.0: PRI_SCH pg_id: 0
hns3 0000:7d:00.0: QS_SCH pg_id: 0
hns3 0000:7d:00.0: BP_TO_QSET pg_id: 0
hns3 0000:7d:00.0: BP_TO_QSET pg_shapping: 0x0
hns3 0000:7d:00.0: BP_TO_QSET qs_bit_map: 0x0
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch prints tc config information.

debugfs command:
echo dump tc > cmd

Sample Output:
root@(none)# echo dump tc > cmd
hns3 0000:7d:00.0: weight_offset: 14
hns3 0000:7d:00.0: tc(0): no sp mode
hns3 0000:7d:00.0: tc(1): no sp mode
hns3 0000:7d:00.0: tc(2): no sp mode
hns3 0000:7d:00.0: tc(3): no sp mode
hns3 0000:7d:00.0: tc(4): no sp mode
hns3 0000:7d:00.0: tc(5): no sp mode
hns3 0000:7d:00.0: tc(6): no sp mode
hns3 0000:7d:00.0: tc(7): no sp mode
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All the Flow Director rules are stored in tcam blocks.
For each bit of tcam entry, the match value
depends on two input value(x, y).

debugfs command:
echo dump fd tcam > cmd

Sample output:
root@(none)# echo dump fd tcam > cmd
hns3 0000:7d:00.0: read result tcam key x(31):
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 08000000
hns3 0000:7d:00.0: 00000600
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: read result tcam key y(31):
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: f7ff0000
hns3 0000:7d:00.0: 0000f900
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 0000fff8
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Query the queue information of the current NIC
such as BD size, queue header and tail pointer.

This  patch adds support for debugfs command:
echo queue info 1 > cmd

it can  print queue config information...

root@(none)# echo queue info 1 > cmd
hns3 0000:7d:00.0: queue info
hns3 0000:7d:00.0: RX(1) BASE ADD: 0x00000000ffb58000
hns3 0000:7d:00.0: RX(1) RING BD NUM: 127
hns3 0000:7d:00.0: RX(1) RING BD LEN: 2
hns3 0000:7d:00.0: RX(1) RING TAIL: 120
hns3 0000:7d:00.0: RX(1) RING HEAD: 0
hns3 0000:7d:00.0: RX(1) RING FBDNUM: 0
hns3 0000:7d:00.0: RX(1) RING PKTNUM: 0
hns3 0000:7d:00.0: TX(1) BASE ADD: 0x00000000fffd8000
hns3 0000:7d:00.0: TX(1) RING BD NUM: 127
hns3 0000:7d:00.0: TX(1) RING TC: 0
hns3 0000:7d:00.0: TX(1) RING TAIL: 2
hns3 0000:7d:00.0: TX(1) RING HEAD: 2
hns3 0000:7d:00.0: TX(1) RING FBDNUM: 0
hns3 0000:7d:00.0: TX(1) RING OFFSET: 0
hns3 0000:7d:00.0: TX(1) RING PKTNUM: 0
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the debugfs framework to the driver and create a debugfs
command interface for each device.

example command:
"echo queue info > cmd" Query the packet forwarding queue information.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ptp_clock_register never return NULL, so no need check this
in cavium_ptp_probe.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A more featureful support for VSC8574 was recently added to the
Microsemi (mscc.c) driver. I checked that features supported in the
Vitesse driver are also supported in the Microsemi driver.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Linu Cherian says:

====================
octeontx2-af: CGX LMAC link bringup and cleanups

Patch 1: Code cleanup
Patch 2: Adds support for an unhandled hardware configuration
Patch 3: Preparatory patch for enabling cgx lmac links
Patch 4: Support for enabling cgx lmac links
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

- Added new CGX firmware interface API for sending link up/down
  commands

- Do link up for cgx lmac ports by default at the time of CGX
  driver probe. Since cgx link up in driver probe affects the
  Linux boot time, linkup procedure is kept threaded using
  workqueues.
  For this, a new cgx API cgx_lmac_linkup_start has been added.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added provision to unregister cgx event callbacks.
This enables the exit path to ensure event callbacks are
unregistered before workqueues get destroyed.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For this, cgx_id(struct cgx) definition has been changed to
reflect cgx port id instead of device instance id.
Now cgx_id can be directly used as channel offset for NPC configuration.
Assumptions on contiguous cgx port ids has been removed from
nix_calibrate_x2p as well.

As a side effect, allocation of conversion tables that were based
on cgx count are changed to cgx port id max value.
Tables would return NULL for invalid cgx ports.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Do CGX init before NIX init
  This would add consistency in NIX code that depends on cgx ports

* Few other misc cleanups
  - rvu_cgx_probe renamed as rvu_cgx_init for consistency
  - rvu_cgx_exit wrapper added to take care of the exit path
  - Added error check on cgx_lmac_event_handler_init
  - Minor cleanups in cgx.h related to tab alignment
  - Removed redundant ids from enum cgx_cmd_id
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer hwdev is being dereferenced when declaring hwif , however, later
on hwdev is being null checked, hence we have dereference before null
check error. Fix this by assigning hwif and pdef only once hwdev has
been null checked.

Detected by CoverityScan, CID#1485581 ("Dereference before null check")

Fixes: 4a61abb1 ("net-next/hinic:add rx checksum offload for HiNIC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: patches 2018-11-22

here are more patches for SMC:
* patches 1-3 and 7 are cleanups without functional change
* patches 4-6 and 8 are optimizations of existing code
* patches 9 and 10 introduce and exploit LLC message DELETE RKEY
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When an rmb is no longer in use by a connection, unregister its rkey at
the remote peer with an LLC DELETE RKEY message. With this change,
unused buffers held in the buffer pool are no longer registered at the
remote peer. They are registered before the buffer is actually used and
unregistered when they are no longer used by a connection.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the infrastructure to send LLC messages of type DELETE RKEY to
unregister a shared memory region at the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a send failed then don't start to wait for a response in
smc_llc_do_confirm_rkey.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For easier reading move the unlock of mutex smc_create_lgr_pending into
smc_listen_work(), i.e. into the function the mutex has been locked.
No functional change.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After sending one of the initial LLC messages CONFIRM LINK or
ADD LINK, there is already a wait for the LLC response. It does
not make sense to wait another long time for a CLC DECLINE. Thus
this patch introduces a shorter wait time for these cases.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a link is terminated that has never reached the active state,
there is no need to trigger an LLC DELETE LINK.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If connection initialization fails for the LLC CONFIRM LINK or the
LLC ADD LINK step, fallback to TCP should be enabled. Thus
the negative return code -EAGAIN should switch to a positive timeout
reason code in these cases, and the internal CLC socket should
not have a set sk_err.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>