Read the ioclk property as reference clock if sclk not present in acpi
table to make it SOC agnostic.
In case, it's not populated from dts/acpi table, use the default clock
of 800 MHz which is optimal in either case of sclk/ioclk.
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Add watchdog timeout handling to cater to the unhandled warnings
seen during validation on boards with different I2C slaves.
This status code reflects the state that controller couldn't
receive any response from slave while being in non-idle state
and HW recommends to reset before any further bus access.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

The macros for TWSI register's offset are generically
named, rename them to be platform specific macros by
adding 'OCTEON_REG' as prefix.
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

To support bus operations for high speed bus frequencies greater than
400KHZ following control bits need to be setup accordingly
 - hs_mode (bit 0) field in Mode register to switch controller
   between low-speed and high-speed frequency operating mode.
 - Setup clock divisors for desired TWSI bus frequency using
   FOSCL output frequency divisor (D):
   0 - sets the divisor to 10 for low speed mode
   1 - sets the divisor to 15 for high speed mode.
The TWSI bus output frequency, in master mode is based on:
                TCLK = 100MHz / (THP + 2)
                FOSCL = FSAMP / (M+1)×D = TCLK / (2 ^ N × (M + 1) × 15)
                FSAMP = TCLK / 2 ^ N
where,
        N is <2:0> and M is <6:3> of TWSI Clock Control Register
        D is 10 for low speed or 15 for HS_MODE

With high speed mode support, HLC mode usage is limited to
low speed frequency (<=400KHz) bus transfers in hardware.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Handle changes to clock divisor logic for OcteonTX2 SoC family using
subsystem ID and using default reference clock source as 100MHz.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Add RISCV support to Cadence I2C Kconfig which is used in platform
such as the StarFive JH8100.
Signed-off-by: Eng Lee Teh <englee.teh@starfivetech.com>
Signed-off-by: Ji Sheng Teoh <jisheng.teoh@starfivetech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout and
simplify the logic a little.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Instead of repeatedly calling clk_get_rate for each transfer, lock
the clock rate and cache the value.
A deadlock has been observed while adding tlv320aic32x4 audio codec to
the system. When this clock provider adds its clock, the clk mutex is
locked already, it needs to access i2c, which in return needs the mutex
for clk_get_rate as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Annotate this variable as __ro_after_init to protect it from being
overwritten later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

i801 as only user of gpio i2c mux removed support for class-based device
instantiation on muxed busses. Class-based device instantiation is a
legacy mechanism and shouldn't be used in new code, therefore remove
support also here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Only remaining client driver supporting I2C_CLASS_SPD is jc42. This
type of thermal sensor can be found on several DDR3/DDR4 modules.
i2c_register_spd() instantiates also such thermal sensor i2c devices.
Since 893fef0b ("i2c: i801: Call i2c_register_spd for muxed child
segments") i2c_register_spd() is called also for the remaining use case,
systems with muxed SMBUS segments for SPD EEPROMs.
Therefore I2C_CLASS_SPD class-based instantiation isn't needed any longer
in this driver, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Granite Rapids-D has additional I2C controller that is enumerated via
ACPI. Add ACPI ID for it.
Signed-off-by: Shanth Murthy <shanth.murthy@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Remove of_node_put from node_ctrl and node struct device_nodes.
Move the declaration to initialization for ensuring scope sanity.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Abhinav Jain <jain.abhinav177@gmail.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Add sc8280xp compatible consistent with recent CAMSS CCI interfaces.

sc8280xp has the following clock list and so requires its own compat
string and sc8280xp specific clock definition in the yaml.

- const: camnoc_axi
- const: slow_ahb_src
- const: cpas_ahb
- const: cci
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Commit 51c87f0e ("dt-bindings: i2c: nxp,pnx-i2c: Convert to dtschema")
converts i2c-pnx.txt to nxp,pnx-i2c.yaml, but misses to adjust the file
entry in ARM/LPC32XX SOC SUPPORT.

Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.

Adjust the file entry in ARM/LPC32XX SOC SUPPORT after this conversion.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

The original change adds usage of i2c_root_adapter(), which is
implemented in i2c-mux.c. Therefore we can't use the multiplexing
if I2C_I801=y and I2C_MUX=m.
Handling the dependencies in the code would become unnecessarily
complex, therefore create a new config symbol.

Fixes: 893fef0b ("i2c: i801: Call i2c_register_spd for muxed child segments")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404042206.MjAQC32x-lkp@intel.com/Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

There is at least one machine that uses this driver but does not
have support for inb()/outb() instructions.

Convert this to using ioport_map() so it can build on architectures
that don't provide these but work correctly on machines that require
using port I/O.

Fixes: 47c21d2d ("i2c: add HAS_IOPORT dependencies")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/lkml/CAMuHMdVUQ2WgtpYPYfO2T=itMmZ7w=geREqDtsP8Q3ODh9rxdw@mail.gmail.com/Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Once the gpio mux driver binds to the "i2c-mux-gpio" platform device,
this creates the i2c adapters for the muxed child segments.
We can use the bus notifier mechanism to check for creation of the
child i2c adapters, and call i2c_register_spd() for them. This allows
to detect all DIMM's on systems with more than 8 memory slots.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Extend the RIIC driver to support the RZ/V2H(P) ("R9A09G057") SoC. It
accomplishes this by appending the compatible string list and passing
the RZ/V2H-specific OF data.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

With an increasing number of SoCs reusing this driver, each with slight
variations in the RIIC IP, it becomes necessary to support passing these
details as OF data. This approach simplifies the extension of the driver
for other SoCs.

This patch lays the groundwork for adding support for the Renesas RZ/V2H
SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Introduce helper functions for performing I2C read and write operations
in the RIIC driver.

These helper functions lay the groundwork for adding support for the
RZ/V2H SoC. This is essential because the register offsets for the RZ/V2H
SoC differ from those of the RZ/A SoC. By abstracting the read and write
operations, we can seamlessly adapt the driver to support different SoC
variants without extensive modifications.

This patch is part of the preparation process for integrating support for
the RZ/V2H SoC into the RIIC driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Document support for the I2C Bus Interface (RIIC) available in the
Renesas RZ/V2H(P) (R9A09G057) SoC.

The RIIC interface in the Renesas RZ/V2H(P) differs from RZ/A in a
couple of ways:
- Register offsets for the RZ/V2H(P) SoC differ from those of the
  RZ/A SoC.
- RZ/V2H register access is limited to 8-bit, whereas RZ/A supports
  8/16/32-bit.
- RZ/V2H has bit differences in the slave address register.

To accommodate these differences, a new compatible string
"renesas,riic-r9a09g057" is added.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>