The 440EPx/GRx chips don't support PCI MRM commands.  Drivers determine this
by looking for a zero value in the PCI cache line size register.  However,
some drivers write to this register upon initialization.  This can cause
MRMs to be used on these chips, which may cause deadlocks on PLB4.

The workaround implemented here introduces a new indirect_type flag, called
PPC_INDIRECT_TYPE_BROKEN_MRM.  This is set in the pci_controller structure in
the pci fixup function for 4xx PCI bridges by determining if the bridge is
compatible with 440EPx/GRx.  The flag is checked in the indirect_write_config
function, and forces any writes to the PCI_CACHE_LINE_SIZE register to be
zero, which will disable MRMs for these chips.

A similar workaround has been tested by AMCC on various PCI cards, such as
the Silicon Image ATA card and Intel E1000 GIGE card.  Hangs were seen with
the Silicon Image card, and MRMs were seen on the bus with a PCI analyzer.
With the workaround in place, the card functioned properly and only Memory
Reads were seen on the bus with the analyzer.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

This makes the sam440ep.dts dts-v1 compliant.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.

It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

This patch add a check to the PPC4xx PCIe driver to detect if the port
is disabled via the device-tree. This is needed for the AMCC Canyonlands
board which has an option to either select 2 PCIe ports or 1 PCIe port
and one SATA port. The SATA port and the 1st PCIe port pins are multiplexed
so we can't start both drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

The "ndfc-chip" device doesn't need any resources. All resources
are handled by the "ndfc-nand" device. Registering the same memory
resource twice causes "cat /proc/iomem" to go into an infinite loop
displaying NDFC memory addresses.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

Add support for the NOR flash found on the AMCC Taishan Board
and enable MTD support in the defconfig.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

This reverts commit acb0142b.

AMCC has indicated that the PPC 460GT does have FPU support.  This
revert enables the FPU for those chips again.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

All the maintained platforms are now in arch/powerpc, so the old
arch/ppc stuff can now go away.
Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: John Linn <john.linn@xilinx.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Since commit 4cb3cee0 the code generated
for the in_beXX() and out_beXX() mmio functions has been sub-optimal.

The out_leXX() family of functions are created with the macro
DEF_MMIO_OUT_LE() while the out_beXX() family are created with
DEF_MMIO_OUT_BE().  In what was perhaps a bit too much macro use, both of
these macros are in turn created via the macro DEF_MMIO_OUT().

For the LE versions, eventually they boil down to an asm that will look
something like this:
asm("sync; stwbrx %1,0,%2" : "=m" (*addr) : "r" (val), "r" (addr));

The issue is that the "stwbrx" instruction only comes in an indexed, or
'x', version, in which the address is represented by the sum of two
registers (the "0,%2").  Unfortunately, gcc doesn't have a constraint for
an indexed memory reference.  The "m" constraint allows both indexed and
offset, i.e. register plus constant, memory references and there is no
"stwbr" version for offset references.  "m" also allows updating addresses
and there is no 'u' version of "stwbrx" like there is with "stwux".

The unused first operand to the asm is just to tell gcc that *addr is an
output of the asm.  The address used is passed in a single register via the
third asm operand, and the index register is just hard coded as 0.  This
means gcc is forced to put the address in a single register and can't use
index addressing, e.g. if one has the data in register 9, a base address in
register 3 and an index in register 4, gcc must emit code like "add 11,4,3;
stwbrx 9,0,11" instead of just "stwbrx 9,4,3".  This costs an extra add
instruction and another register.

For gcc 4.0 and older, there doesn't appear to be anything that can be
done.  But for 4.1 and newer, there is a 'Z' constraint.  It does not allow
"updating" addresses, but does allow both indexed and offset addresses.
However, the only allowed constant offset is 0.  We can then use the
undocumented 'y' operand modifier, which causes gcc to convert "0(reg)"
into the equivilient "0,reg" format that can be used with stwbrx.

This brings us the to problem with the BE version.  In this case, the "stw"
instruction does have both indexed and non-indexed versions.  The final asm
ends up looking like this:
asm("sync; stw%U0%X0 %1,%0" : "=m" (*addr) : "r" (val), "r" (addr));

The undocumented codes "%U0" and "%0X" will generate a 'u' if the memory
reference should be an auto-updating one, and an 'x' if the memory
reference is indexed, respectively.  The third operand is unused, it's just
there because asm the code is reused from the LE version.  However, gcc
does not know this, and generates unnecessary code to stick addr in a
register!  To use the example from the LE version, gcc will generate "add
11,4,3; stwx 9,4,3".  It is able to use the indexed address "4,3" for the
"stwx", but still thinks it needs to put 4+3 into register 11, which will
never be used.

This also ends up happening a lot for the offset addressing mode, where
common code like this:  out_be32(&device_registers->some_register, data);
uses an instruction like "stw 9, 42(3)", where register 3 has the pointer
device_registers and 42 is the offset of some_register in that structure.
gcc will be forced to generate the unnecessary instruction "addi 11, 3, 42"
to put the address into a single (unused) register.

The in_* versions end up having these exact same problems as well.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When I changed irq_alloc_host() to take an of_node
(52964f87: "Add an optional
device_node pointer to the irq_host"), I botched the reference
counting semantics.

Stephen pointed out that it's irq_alloc_host()'s business if
it needs to take an additional reference to the device_node,
the caller shouldn't need to care.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

If we do the call to of_address_to_resource() first, then we don't
need to worry about freeing the irq_host (which the code doesn't do
currently anyway).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

If we do the call to of_address_to_resource() first, then we don't
need to worry about freeing the irq_host (which the code doesn't do
currently anyway).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

If we do the call to irq_of_parse_and_map() first, then we don't
need to worry about freeing the irq_host.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Make sure CONFIG_TASK_SIZE does not overlap CONFIG_KERNEL_START
This could happen when overriding settings to get 1GB lowmem, and would lead
to userland mysteriousely hanging.

This setting is only used by PPC32.
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This eliminates this minor boot-time debugging error message:

[    1.316451] calling  add_pcspkr+0x0/0x84
[    1.316478] initcall add_pcspkr+0x0/0x84 returned -19 after 0 msecs
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).

Part 5 of 5: add the Kconfig entry for the C2K board.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).

Part 4 of 5: this is the default config for the board.  In this
configuration the kernel is going to try to boot from MTD
partition 3 on the NOR flash (see c2k.dts for details about
the partitioning of the flash).
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).

Part 3 of 5: driver for the board.  At this time it is very generic
and similar to its original, the driver for the prpmc2800.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).

Part 2 of 5: support for the board in arch/powerpc/boot.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).

Part 1 of 5: DTS file describing the board peripherals.  As far as I
know all peripherals except the FPGA are listed in there (I did not
include the FPGA because a lot of work is needed there).
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This fixes the following warning, introduced by commit
475ca391 (mpic: Deal with bogus NIRQ
in Feature Reporting Register):

  CC      arch/powerpc/sysdev/mpic.o
arch/powerpc/sysdev/mpic.c: In function 'mpic_alloc':
arch/powerpc/sysdev/mpic.c:1146: warning: suggest explicit braces to avoid ambiguous 'else'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Conflicts:

	arch/powerpc/sysdev/fsl_soc.c

Now that walk_memory_resource() is available regardless of
MEMORY_HOTPLUG's setting, this dependency is not needed.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The ehea driver was recently changed[1] to use walk_memory_resource() to
detect the system's memory layout.  However, walk_memory_resource() is
available only when memory hotplug is enabled.  So CONFIG_EHEA was
made to depend on MEMORY_HOTPLUG [2], but it is inappropriate for a
network driver to have such a dependency.

Make the declaration of walk_memory_resource() and its powerpc
implementation (ehea is powerpc-specific) unconditionally available.

[1] 48cfb14f
    "ehea: Add DLPAR memory remove support"

[2] fb7b6ca2
    "ehea: Add dependency to Kconfig"
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

During the next merge window, pci_name()'s return value will become
const, so use the new dev_set_name() instead to avoid the warning (from
linux-next):

arch/powerpc/kernel/pci_64.c: In function 'of_create_pci_dev':
arch/powerpc/kernel/pci_64.c:193: warning: passing argument 1 of 'sprintf' discards qualifiers from pointer target type

Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When building a signal or a ucontext, we can incorrectly set the MSR_VEC
bit of the kernel pt_regs->msr before returning to userspace if the task
-ever- used VMX.

This can lead to funny result if that stack used it in the past, then
"lost" it (ie. it wasn't enabled after a context switch for example)
and then called get_context.  It can end up with VMX enabled and the
registers containing values from some other task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This corrects the names of two CONFIG_ variables.

Note that the CONFIG_MPC86XADS fix uncovers another bug
(with mpc866_ads_defconfig) that will require fixing:

<--  snip  -->

...
arch/powerpc/boot/dtc -O dtb -o arch/powerpc/boot/mpc866ads.dtb -b 0  /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts
DTC: dts->dtb  on file "/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts"
  WRAP    arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1

<--  snip  -->
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

use_mm() was changed to use switch_mm() instead of activate_mm(), since
then nobody calls (and nobody should call) activate_mm() with
PF_BORROWED_MM bit set.

As Jeff Dike pointed out, we can also remove the "old != new" check, it is
always true.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ipath: Fix SM trap forwarding
  IB/ehca: Reject send WRs only for RESET, INIT and RTR state
  MAINTAINERS: Update NetEffect (iw_nes) entry
  IB/ipath: Fix device capability flags
  IB/ipath: Avoid test_bit() on u64 SDMA status value

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  x86/PCI: add workaround for bug in ASUS A7V600 BIOS (rev 1005)
  PCI/x86: fix up PCI stuff so that PCI_GOANY supports OLPC

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: emu10k1 - fix system hang with Audigy2 ZS Notebook PCMCIA card

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/chrisw/lsm-2.6:
  capabilities: remain source compatible with 32-bit raw legacy capability support.
  LSM: remove stale web site from MAINTAINERS

* git://git.infradead.org/~dwmw2/mtd-2.6.26:
  [MTD] m25p80.c mutex unlock fix

Packet sending is driven by two flags, tx_ready and tx_queued.
It was possible, that there were queued data for sending and
hardware was flagged as blocked but in fact it was not.

The tx_queued was indicator but should be really a counter else
first fragmented packet resets tx_queued flag, but there may be
pending packets which do not get sent.

New semantics:
tx_ready - set, if hw is ready to send packet, no packet is being
           transferred right now
           set the flag right at the place where data are copied
           into hw memory and not earlier without checking if it
           was succesful
tx_queued - count of enqueued packets, including fragments
Tested-by: Michal Rokos <michal.rokos@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

To get zeroed out memory from a particular NUMA node.  To be used by
sunrpc.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Just a quick explanation of the pagemap interface from a userspace point
of view, and an example of how to use it (in English, not code).
Signed-off-by: Thomas  Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the user tries to read from a position that is not a multiple of 8, or
read a number of bytes that is not a multiple of 8, they have passed an
invalid argument to read, for the purpose of reading these files.  It's
not an IO error because we didn't encounter any trouble finding the data
they asked for.
Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since pagemap is all about examining pages mapped into processes' memory
spaces, it makes sense for kpagecount to return the map counts, not the
reference counts.
Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>