As the driver uses GRO and not LRO, LRO settings are ignored anyway
and are removed here to avoid confusion.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simple conversion.

This also fixes a bug in TX checksum toggling --- driver was changing
NETIF_F_HW_CSUM instead of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

just IP_CSUM.  This needs testing and so is not changed here.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling setup_wol after a reset is inconsequential.
The WOL setting should be programmed before FLR.
And yes, FLR does not erase wol information.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of a fixed sized array for vf_cfg, allocate the size dynamically
depending on number of VFs the device supports.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The user supplied num_vfs value need not be compared
against a static BE_MAX_VF, but can be checked against
the actual VFs that the device can support.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lancer and BE can both use SLI_INTF_REG to check a VF or a PF.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add rxhash support,
Based on initial work by Eric Dumazet.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/benet/be_main.c

Commit 1018b5c0 ("Set rt->rt_iif more
sanely on output routes.")  breaks rt_is_{output,input}_route.

This became the cause to return "IP_PKTINFO's ->ipi_ifindex == 0".

To fix it, this does:

1) Add "int rt_route_iif;" to struct rtable

2) For input routes, always set rt_route_iif to same value as rt_iif

3) For output routes, always set rt_route_iif to zero.  Set rt_iif
   as it is done currently.

4) Change rt_is_{output,input}_route() to test rt_route_iif
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit c6e1a0d1 broken the calc
 (net: Allow no-cache copy from user on transmit)
of checksum, which may cause some tcp packets be dropped because
incorrect checksum. ssh does not work under today's net-next-2.6
tree.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ethtool infrastructure for blinking, which is now does
locking at higher level.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert driver to use new ethtool set_phys_id.
Not completely sure that this is correct for all cases of device
up/down and doing operation. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather simple conversion to hw_features.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

udev fully replaces this special file system that only contains CAPI
NCCI TTY device nodes. User space (pppdcapiplugin) works without
noticing the difference.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes error from sparse:
  CHECK   drivers/net/xen-netback/xenbus.c
drivers/net/xen-netback/xenbus.c:29:40: error: dubious one-bit signed bitfield

        int have_hotplug_status_watch:1;
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

eq_next_idx is not getting reset to zero during suspend.
This causes resume to fail. Added the fix.
Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Renamed msix_vec_idx to eq_idx in be_eq_obj struct.
Renamed msix_vec_next_idx to eq_next_idx in be_adapter structure.
These members are used in INTX mode also.
Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert to new ethtool set physical id model. Remove no longer used
timer, and fix docbook comment.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also cleanup error codes to no lie about things that driver doesn't
support. If device is down report -EAGAIN (same as Broadcom), and
if port doesn't blink then error as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In this case, need to add element to device private to hold
original led state.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also fix up incorrect docbook comment
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement new ethtool set_phys_id on Chelsio cxgb3 board.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement control of LED via set_phys_id.
Note: since PHY is powered off if device is down, this board
only allows blinking if device is up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement set_phys_id led control on SysKonnect board.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ethtool set_phys_id to control LED. Fixes issues with RTNL being
held for extended periods.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

otherwise we loop forever if a PPPoE socket was set
to PPPOX_ZOMBIE state by a PADT message when the
ethernet device is going down afterwards.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6085 is identical to the mv88e6095, except that all ports are
10/100 Mb/s, so use the existing setup code except for the cpu/dsa speed
selection in _setup_port().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

properly record sk_rxhash in ipv6 sockets (v2)

Noticed while working on another project that flows to sockets which I had open
on a test systems weren't getting steered properly when I had RFS enabled.
Looking more closely I found that:

1) The affected sockets were all ipv6
2) They weren't getting steered because sk->sk_rxhash was never set from the
incomming skbs on that socket.

This was occuring because there are several points in the IPv4 tcp and udp code
which save the rxhash value when a new connection is established.  Those calls
to sock_rps_save_rxhash were never added to the corresponding ipv6 code paths.
This patch adds those calls.  Tested by myself to properly enable RFS
functionalty on ipv6.

Change notes:
v2:
	Filtered UDP to only arm RFS on bound sockets (Eric Dumazet)
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bumped up version number to 5.0.16
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o In dev->open LRO was enabled by default, enable it depending
  upon netdev->features , kernel may have disabled it.
o Configure LRO when interface is up.
Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <Anirban.Chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use flash layout table to get flash fw starting address and its size.
If that fails, use legacy method.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleaned up unused codes for interrupt coalescence settings
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Made changes to VLAN code comply with new VLAN infrastructure in kernel
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Optimized code resulted in achieving lower CPU utilization on transmit path
and higher throughput for small packet sizes (64 bytes).
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>