- 22 Sep, 2022 14 commits
-
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 6.1 - fixes - suspend/resume improvements - tx status reporting improvements
-
Ching-Te Ku authored
Since we maintain coexistence as shared code, so move coexistence version from chip specific attribute to a definition. Signed-off-by:
Ching-Te Ku <ku920601@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220920010939.12173-10-pkshih@realtek.com
-
Ching-Te Ku authored
Add control logic to operate Wi-Fi to BT scoreboard to control BT scan priority. And patch mechanism parameter to enhance Wi-Fi throughput while coexisting with BT profile & BT scan. Set PTA priority let Wi-Fi BT can RX at the same time. Signed-off-by:
-
Ching-Te Ku authored
If Wi-Fi driver send Wi-Fi status to BT via scoreboard too frequent in a short moment, BT will loss some of them because of hardware response time. To avoid this issue, change the code flow. Summarize the scoreboard changes and if the value have changed, send the scoreboard to BT only once in a coexistence processing cycle. It also can help to reduce driver I/O. Signed-off-by:
-
Ching-Te Ku authored
To prevent LNA2 change its gain during a Wi-Fi aggregation packet while GNT_BT pull high. Otherwise, changes of this gain will destroy the whole aggregation when Wi-Fi RX. Signed-off-by:
-
Ching-Te Ku authored
WiFi/BT combo module could only have two antenna, namely WL_S0 and WL_S1. WiFi can use two antenna to TX/RX 2SS data, and BT can share one of the antenna. This patch is to allow WiFi to TX/RX 1SS data like ACK/RTS/CTS to improve Wi-Fi performance while coexisting with Bluetooth. Signed-off-by:
-
Ching-Te Ku authored
This report is to record firmware call flow like notify events, and take actions. This can help to address if firmware flow is in expectation. Implement v1 parser to support 8852CE firmware report. Signed-off-by:
-
Ching-Te Ku authored
This debug entry is to summarize important messages to quickly address problem types, such as firmware hang, C2H/H2C stuck, or too much occupation of BT A2DP. If unexpected something is addressed, we can dig the problem via other debug messages that provide more detail information. Signed-off-by:
-
Ching-Te Ku authored
To analyze debug log quickly, use readable name in string format instead. Signed-off-by:
-
Ching-Te Ku authored
'cysta' is short for statistics for cycles. That is a circular buffer to record snapshot status including beacon count, RX count, TX count etc. Since 8852CE Wi-Fi firmware report this statistics in different format, add v1 parser by this patch. Signed-off-by:
-
Johannes Berg authored
There are two, just change them to have a "u8 data[]" type member, and add casts where needed. No binary changes. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Reviewed-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
-
Johannes Berg authored
Use "u8 bssid_data[]" with an appropriate cast. No binary changes. Signed-off-by:
-
Johannes Berg authored
There are a number of these here, fix them by using appropriate casts. No binary changes. Signed-off-by:
-
Duoming Zhou authored
There are sleep in atomic context bugs when uploading device dump data in mwifiex. The root cause is that dev_coredumpv could not be used in atomic contexts, because it calls dev_set_name which include operations that may sleep. The call tree shows execution paths that could lead to bugs: (Interrupt context) fw_dump_timer_fn mwifiex_upload_device_dump dev_coredumpv(..., GFP_KERNEL) dev_coredumpm() kzalloc(sizeof(*devcd), gfp); //may sleep dev_set_name kobject_set_name_vargs kvasprintf_const(GFP_KERNEL, ...); //may sleep kstrdup(s, GFP_KERNEL); //may sleep The corresponding fail log is shown below: [ 135.275938] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start [ 135.281029] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265 ... [ 135.293613] Call Trace: [ 135.293613] <IRQ> [ 135.293613] dump_stack_lvl+0x57/0x7d [ 135.293613] __might_resched.cold+0x138/0x173 [ 135.293613] ? dev_coredumpm+0xca/0x2e0 [ 135.293613] kmem_cache_alloc_trace+0x189/0x1f0 [ 135.293613] ? devcd_match_failing+0x30/0x30 [ 135.293613] dev_coredumpm+0xca/0x2e0 [ 135.293613] ? devcd_freev+0x10/0x10 [ 135.293613] dev_coredumpv+0x1c/0x20 [ 135.293613] ? devcd_match_failing+0x30/0x30 [ 135.293613] mwifiex_upload_device_dump+0x65/0xb0 [ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0 [ 135.293613] call_timer_fn+0x122/0x3d0 [ 135.293613] ? msleep_interruptible+0xb0/0xb0 [ 135.293613] ? lock_downgrade+0x3c0/0x3c0 [ 135.293613] ? __next_timer_interrupt+0x13c/0x160 [ 135.293613] ? lockdep_hardirqs_on_prepare+0xe/0x220 [ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0 [ 135.293613] __run_timers.part.0+0x3f8/0x540 [ 135.293613] ? call_timer_fn+0x3d0/0x3d0 [ 135.293613] ? arch_restore_msi_irqs+0x10/0x10 [ 135.293613] ? lapic_next_event+0x31/0x40 [ 135.293613] run_timer_softirq+0x4f/0xb0 [ 135.293613] __do_softirq+0x1c2/0x651 ... [ 135.293613] RIP: 0010:default_idle+0xb/0x10 [ 135.293613] RSP: 0018:ffff888006317e68 EFLAGS: 00000246 [ 135.293613] RAX: ffffffff82ad8d10 RBX: ffff888006301cc0 RCX: ffffffff82ac90e1 [ 135.293613] RDX: ffffed100d9ff1b4 RSI: ffffffff831ad140 RDI: ffffffff82ad8f20 [ 135.293613] RBP: 0000000000000003 R08: 0000000000000000 R09: ffff88806cff8d9b [ 135.293613] R10: ffffed100d9ff1b3 R11: 0000000000000001 R12: ffffffff84593410 [ 135.293613] R13: 0000000000000000 R14: 0000000000000000 R15: 1ffff11000c62fd2 ... [ 135.389205] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end This patch uses delayed work to replace timer and moves the operations that may sleep into a delayed work in order to mitigate bugs, it was tested on Marvell 88W8801 chip whose port is usb and the firmware is usb8801_uapsta.bin. The following is the result after using delayed work to replace timer. [ 134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start [ 135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end As we can see, there is no bug now. Fixes: f5ecd02a ("mwifiex: device dump support for usb interface") Signed-off-by:Duoming Zhou <duoming@zju.edu.cn> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
- 19 Sep, 2022 26 commits
-
-
Dan Carpenter authored
If request_partial_firmware_into_buf() fails then "firmware" is not initialized and the release_firmware(firmware) will crash. Fixes: deebea35 ("wifi: rtw89: early recognize FW feature to decide if chanctx") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
-
Hans de Goede authored
Even though ieee80211_hw.queues is set to 2, the ralink rt2x00 driver is seeing tx skbs submitted to it with the queue-id set to 2 / set to IEEE80211_AC_BE on a rt2500 card when associating with an access-point. This causes rt2x00queue_get_tx_queue() to return NULL and the following error to be logged: "ieee80211 phy0: rt2x00mac_tx: Error - Attempt to send packet over invalid queue 2", after which association with the AP fails. This patch works around this by mapping QID_AC_BE and QID_AC_BK to QID_AC_VI when there are only 2 tx_queues. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by:
-
Po-Hao Huang authored
Update tx descriptor settings so broadcast packets on other ports can be issued properly when DTIM count is 0. Before this, all broadcast packets are sent via port 0 and won't be transmitted correctly. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Po-Hao Huang authored
In monitor mode we should be able to received all packets even if it's not destined to us. But after scan, the configuration was wrongly set, so we fix it. Signed-off-by:
-
Po-Hao Huang authored
This avoid potential memory leak under power saving mode. Signed-off-by:
-
Ping-Ke Shih authored
Reset these registers to prevent firmware get false alarm after wifi CPU is running. Signed-off-by:
-
Ping-Ke Shih authored
Modify PCI LTR control flow and LTR idle latency to improve power save efficiency. Signed-off-by:
-
Ping-Ke Shih authored
NAV upper register is to limit the maximum NAV value to prevent unexpected NAV, but the old setting is too small to reflect NAV from AP transmiting big MPDU at once. Signed-off-by:
-
Ping-Ke Shih authored
8852C needs this to change CMAC dma to full mode to keep receiving packets after RX full event being resolved. Signed-off-by:
-
Zong-Zhe Yang authored
SER (system error recovery) can deal with different crash types by different levels of processes. Previous FW crash simulation triggers a CPU exception which is one kind of SER L2 type. It can verify SER L2 flow which includes HW/FW restart. Now, we want to increase crash simulation types. A debug function is added to trigger control error in purpose for SER L1 simulation/verification. And, debugfs fw_crash is extended to accept different parameters. echo 1 > fw_crash: simulate CPU exception as before (keep 1 for compatibility with previous) It will be catched and handled by SER L2. (this requires HW/FW restart) echo 2 > fw_crash: simulate control error It will be catched and handled by SER L1. (driver and FW cooperate to recover this) Besides, in order to apply to the above two cases, rename RTW89_FLAG_RESTART_TRIGGER to RTW89_FLAG_CRASH_SIMULATING and adjust where SER flow clears this bit for both L1 and L2. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Zong-Zhe Yang authored
With FW >= v0.27.40.0, 8852C FW has feature to handle crash simulation. Besides, use RTW89_WCPU_BASE_MASK to replace use of RTW89_WCPU_BASE_ADDR and work for both 8852A and 8852C. Signed-off-by:
-
Zong-Zhe Yang authored
Introudce a H2C feature to drop packets according to given parameters. And, we implement instances to drop packets from BE, BK, VI, VO queues by vif or sta. Then, we refine our callback of ieee80211_ops::flush to deal with the case of drop=true via this feature. Signed-off-by:
-
Ping-Ke Shih authored
Seaprate calling of rtw89_h2c_tx() out of if-expression, and bypass the return value to upper caller. Signed-off-by:
-
Chin-Yen Lee authored
Different chips use different register and mask for tx dma channels, so concentrate them. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
-
Chin-Yen Lee authored
Some PCI and MAC registers are changed for different chips and correct them accordingly. And HCI MAD functions belongs to MAC core, so move it to mac.h/.c. Signed-off-by:
-
Zong-Zhe Yang authored
For 8852C, rtw89_pci_lv1rst_stop_dma() and rtw89_pci_lv1rst_start_dma() are offloaded to FW L1 reset flow. So, driver no longer needs to do them. Signed-off-by:
-
Kuan-Chung Chen authored
Add ops set_tid_config to support TID specific configuration. We currently only support ampdu setting. The command example is: iw wlan0 set tidconf tids 0x3 ampdu off iw wlan0 set tidconf peer xx:xx:xx:xx:xx:xx tids 0x2 ampdu on Signed-off-by:
Kuan-Chung Chen <damon.chen@realtek.com> Signed-off-by:
-
Kuan-Chung Chen authored
Support setting HE GI and LTF values to the kernel via nl80211. We currently only support some GI and LTF values settings. The command example is: iw wlan0 set bitrates he-gi-2.4 0.8 he-ltf-2.4 2 Signed-off-by:
-
Ping-Ke Shih authored
The variable cnt_connecting is to indicate if we are connecting to an AP. This is an important clue for coexistence to assign more time slot to WiFi side in this situation to ensure WiFi can establish connection. Without this patch, compiler warns: drivers/net/wireless/realtek/rtw89/coex.c:3244:25: warning: variable 'cnt_connecting' set but not used [-Wunused-but-set-variable] Reported-by:kernel test robot <lkp@intel.com> Signed-off-by:
-
Ching-Te Ku authored
To reduce register IO, combine set_gnt_wl/set_gnt_bt to set the same register one time. Because RTL8852C use different register to control antenna path, so make correction of path control related debug logs. Signed-off-by:
-
Ching-Te Ku authored
RTL8852C don't need to send the data trace_step which used to tell firmware how many TDMA steps should record. Remove the member. Signed-off-by:
-
Ching-Te Ku authored
Show TDMA information containing TDMA policy and time slot of Wi-Fi/BT in debug message to check things are in expected. The v1 format contains additional header, and remaining part is the same as original. So 8852CE selects v1 version, and then everything like original. Signed-off-by:
-
Ching-Te Ku authored
Parsing firmware error message from original version and v1 reports to show up exception counter of commands from firmware in debug message. Then, we can make sure exchange commands are correct totally. In the later version Wi-Fi firmware(v1), the report format was changed. With this update, we can yield correct report from proper struct. Signed-off-by:
-
Ching-Te Ku authored
Because RTL8852A/RTL8852C use different firmware buffer size to send C2H packet, it's necessary to use different size to parse C2H report. Signed-off-by:
-
Ching-Te Ku authored
The later version Wi-Fi firmware will report null data TX times, so the structure is different from before. Signed-off-by:
-
Ping-Ke Shih authored
With void pointer, we don't need to cast to 'u8 *' by one by. Signed-off-by:
-
