- 26 Jul, 2019 40 commits
-
-
Dundi Raviteja authored
[ Upstream commit c709df58 ] Currently the memory allocated for qmi handle is not being freed during de-init which leads to memory leak. Free the allocated qmi memory in qmi deinit to avoid memory leak. Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1 Fixes: fda6fee0001e ("ath10k: add QMI message handshake for wcn3990 client") Signed-off-by:
Dundi Raviteja <dundi@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Yunsheng Lin authored
[ Upstream commit 04f25edb ] When hdev->tx_sch_mode is HCLGE_FLAG_VNET_BASE_SCH_MODE, the hclge_tm_schd_mode_vnet_base_cfg calls hclge_tm_pri_schd_mode_cfg with vport->vport_id as pri_id, which is used as index for hdev->tm_info.tc_info, it will cause out of bound access issue if vport_id is equal to or larger than HNAE3_MAX_TC. Also hardware only support maximum speed of HCLGE_ETHER_MAX_RATE. So this patch adds two checks for above cases. Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Yonglong Liu authored
[ Upstream commit 18d219b7 ] When setting -Wformat=2, there is a compiler warning like this: hclge_main.c:xxx:x: warning: format not a string literal and no format arguments [-Wformat-nonliteral] strs[i].desc); ^~~~ This patch adds missing format parameter "%s" to snprintf() to fix it. Fixes: 46a3df9f ("Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
-
Coly Li authored
[ Upstream commit 7e865eba ] When enable lockdep and reboot system with a writeback mode bcache device, the following potential deadlock warning is reported by lockdep engine. [ 101.536569][ T401] kworker/2:2/401 is trying to acquire lock: [ 101.538575][ T401] 00000000bbf6e6c7 ((wq_completion)bcache_writeback_wq){+.+.}, at: flush_workqueue+0x87/0x4c0 [ 101.542054][ T401] [ 101.542054][ T401] but task is already holding lock: [ 101.544587][ T401] 00000000f5f305b3 ((work_completion)(&cl->work)#2){+.+.}, at: process_one_work+0x21e/0x640 [ 101.548386][ T401] [ 101.548386][ T401] which lock already depends on the new lock. [ 101.548386][ T401] [ 101.551874][ T401] [ 101.551874][ T401] the existing dependency chain (in reverse order) is: [ 101.555000][ T401] [ 101.555000][ T401] -> #1 ((work_completion)(&cl->work)#2){+.+.}: [ 101.557860][ T401] process_one_work+0x277/0x640 [ 101.559661][ T401] worker_thread+0x39/0x3f0 [ 101.561340][ T401] kthread+0x125/0x140 [ 101.562963][ T401] ret_from_fork+0x3a/0x50 [ 101.564718][ T401] [ 101.564718][ T401] -> #0 ((wq_completion)bcache_writeback_wq){+.+.}: [ 101.567701][ T401] lock_acquire+0xb4/0x1c0 [ 101.569651][ T401] flush_workqueue+0xae/0x4c0 [ 101.571494][ T401] drain_workqueue+0xa9/0x180 [ 101.573234][ T401] destroy_workqueue+0x17/0x250 [ 101.575109][ T401] cached_dev_free+0x44/0x120 [bcache] [ 101.577304][ T401] process_one_work+0x2a4/0x640 [ 101.579357][ T401] worker_thread+0x39/0x3f0 [ 101.581055][ T401] kthread+0x125/0x140 [ 101.582709][ T401] ret_from_fork+0x3a/0x50 [ 101.584592][ T401] [ 101.584592][ T401] other info that might help us debug this: [ 101.584592][ T401] [ 101.588355][ T401] Possible unsafe locking scenario: [ 101.588355][ T401] [ 101.590974][ T401] CPU0 CPU1 [ 101.592889][ T401] ---- ---- [ 101.594743][ T401] lock((work_completion)(&cl->work)#2); [ 101.596785][ T401] lock((wq_completion)bcache_writeback_wq); [ 101.600072][ T401] lock((work_completion)(&cl->work)#2); [ 101.602971][ T401] lock((wq_completion)bcache_writeback_wq); [ 101.605255][ T401] [ 101.605255][ T401] *** DEADLOCK *** [ 101.605255][ T401] [ 101.608310][ T401] 2 locks held by kworker/2:2/401: [ 101.610208][ T401] #0: 00000000cf2c7d17 ((wq_completion)events){+.+.}, at: process_one_work+0x21e/0x640 [ 101.613709][ T401] #1: 00000000f5f305b3 ((work_completion)(&cl->work)#2){+.+.}, at: process_one_work+0x21e/0x640 [ 101.617480][ T401] [ 101.617480][ T401] stack backtrace: [ 101.619539][ T401] CPU: 2 PID: 401 Comm: kworker/2:2 Tainted: G W 5.2.0-rc4-lp151.20-default+ #1 [ 101.623225][ T401] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/13/2018 [ 101.627210][ T401] Workqueue: events cached_dev_free [bcache] [ 101.629239][ T401] Call Trace: [ 101.630360][ T401] dump_stack+0x85/0xcb [ 101.631777][ T401] print_circular_bug+0x19a/0x1f0 [ 101.633485][ T401] __lock_acquire+0x16cd/0x1850 [ 101.635184][ T401] ? __lock_acquire+0x6a8/0x1850 [ 101.636863][ T401] ? lock_acquire+0xb4/0x1c0 [ 101.638421][ T401] ? find_held_lock+0x34/0xa0 [ 101.640015][ T401] lock_acquire+0xb4/0x1c0 [ 101.641513][ T401] ? flush_workqueue+0x87/0x4c0 [ 101.643248][ T401] flush_workqueue+0xae/0x4c0 [ 101.644832][ T401] ? flush_workqueue+0x87/0x4c0 [ 101.646476][ T401] ? drain_workqueue+0xa9/0x180 [ 101.648303][ T401] drain_workqueue+0xa9/0x180 [ 101.649867][ T401] destroy_workqueue+0x17/0x250 [ 101.651503][ T401] cached_dev_free+0x44/0x120 [bcache] [ 101.653328][ T401] process_one_work+0x2a4/0x640 [ 101.655029][ T401] worker_thread+0x39/0x3f0 [ 101.656693][ T401] ? process_one_work+0x640/0x640 [ 101.658501][ T401] kthread+0x125/0x140 [ 101.660012][ T401] ? kthread_create_worker_on_cpu+0x70/0x70 [ 101.661985][ T401] ret_from_fork+0x3a/0x50 [ 101.691318][ T401] bcache: bcache_device_free() bcache0 stopped Here is how the above potential deadlock may happen in reboot/shutdown code path, 1) bcache_reboot() is called firstly in the reboot/shutdown code path, then in bcache_reboot(), bcache_device_stop() is called. 2) bcache_device_stop() sets BCACHE_DEV_CLOSING on d->falgs, then call closure_queue(&d->cl) to invoke cached_dev_flush(). And in turn cached_dev_flush() calls cached_dev_free() via closure_at() 3) In cached_dev_free(), after stopped writebach kthread dc->writeback_thread, the kwork dc->writeback_write_wq is stopping by destroy_workqueue(). 4) Inside destroy_workqueue(), drain_workqueue() is called. Inside drain_workqueue(), flush_workqueue() is called. Then wq->lockdep_map is acquired by lock_map_acquire() in flush_workqueue(). After the lock acquired the rest part of flush_workqueue() just wait for the workqueue to complete. 5) Now we look back at writeback thread routine bch_writeback_thread(), in the main while-loop, write_dirty() is called via continue_at() in read_dirty_submit(), which is called via continue_at() in while-loop level called function read_dirty(). Inside write_dirty() it may be re-called on workqueeu dc->writeback_write_wq via continue_at(). It means when the writeback kthread is stopped in cached_dev_free() there might be still one kworker queued on dc->writeback_write_wq to execute write_dirty() again. 6) Now this kworker is scheduled on dc->writeback_write_wq to run by process_one_work() (which is called by worker_thread()). Before calling the kwork routine, wq->lockdep_map is acquired. 7) But wq->lockdep_map is acquired already in step 4), so a A-A lock (lockdep terminology) scenario happens. Indeed on multiple cores syatem, the above deadlock is very rare to happen, just as the code comments in process_one_work() says, 2263 * AFAICT there is no possible deadlock scenario between the 2264 * flush_work() and complete() primitives (except for single-threaded 2265 * workqueues), so hiding them isn't a problem. But it is still good to fix such lockdep warning, even no one running bcache on single core system. The fix is simple. This patch solves the above potential deadlock by, - Do not destroy workqueue dc->writeback_write_wq in cached_dev_free(). - Flush and destroy dc->writeback_write_wq in writebach kthread routine bch_writeback_thread(), where after quit the thread main while-loop and before cached_dev_put() is called. By this fix, dc->writeback_write_wq will be stopped and destroy before the writeback kthread stopped, so the chance for a A-A locking on wq->lockdep_map is disappeared, such A-A deadlock won't happen any more. Signed-off-by:
Coly Li <colyli@suse.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Coly Li authored
[ Upstream commit b387e9b5 ] When system memory is in heavy pressure, bch_gc_thread_start() from run_cache_set() may fail due to out of memory. In such condition, c->gc_thread is assigned to -ENOMEM, not NULL pointer. Then in following failure code path bch_cache_set_error(), when cache_set_flush() gets called, the code piece to stop c->gc_thread is broken, if (!IS_ERR_OR_NULL(c->gc_thread)) kthread_stop(c->gc_thread); And KASAN catches such NULL pointer deference problem, with the warning information: [ 561.207881] ================================================================== [ 561.207900] BUG: KASAN: null-ptr-deref in kthread_stop+0x3b/0x440 [ 561.207904] Write of size 4 at addr 000000000000001c by task kworker/15:1/313 [ 561.207913] CPU: 15 PID: 313 Comm: kworker/15:1 Tainted: G W 5.0.0-vanilla+ #3 [ 561.207916] Hardware name: Lenovo ThinkSystem SR650 -[7X05CTO1WW]-/-[7X05CTO1WW]-, BIOS -[IVE136T-2.10]- 03/22/2019 [ 561.207935] Workqueue: events cache_set_flush [bcache] [ 561.207940] Call Trace: [ 561.207948] dump_stack+0x9a/0xeb [ 561.207955] ? kthread_stop+0x3b/0x440 [ 561.207960] ? kthread_stop+0x3b/0x440 [ 561.207965] kasan_report+0x176/0x192 [ 561.207973] ? kthread_stop+0x3b/0x440 [ 561.207981] kthread_stop+0x3b/0x440 [ 561.207995] cache_set_flush+0xd4/0x6d0 [bcache] [ 561.208008] process_one_work+0x856/0x1620 [ 561.208015] ? find_held_lock+0x39/0x1d0 [ 561.208028] ? drain_workqueue+0x380/0x380 [ 561.208048] worker_thread+0x87/0xb80 [ 561.208058] ? __kthread_parkme+0xb6/0x180 [ 561.208067] ? process_one_work+0x1620/0x1620 [ 561.208072] kthread+0x326/0x3e0 [ 561.208079] ? kthread_create_worker_on_cpu+0xc0/0xc0 [ 561.208090] ret_from_fork+0x3a/0x50 [ 561.208110] ================================================================== [ 561.208113] Disabling lock debugging due to kernel taint [ 561.208115] irq event stamp: 11800231 [ 561.208126] hardirqs last enabled at (11800231): [<ffffffff83008538>] do_syscall_64+0x18/0x410 [ 561.208127] BUG: unable to handle kernel NULL pointer dereference at 000000000000001c [ 561.208129] #PF error: [WRITE] [ 561.312253] hardirqs last disabled at (11800230): [<ffffffff830052ff>] trace_hardirqs_off_thunk+0x1a/0x1c [ 561.312259] softirqs last enabled at (11799832): [<ffffffff850005c7>] __do_softirq+0x5c7/0x8c3 [ 561.405975] PGD 0 P4D 0 [ 561.442494] softirqs last disabled at (11799821): [<ffffffff831add2c>] irq_exit+0x1ac/0x1e0 [ 561.791359] Oops: 0002 [#1] SMP KASAN NOPTI [ 561.791362] CPU: 15 PID: 313 Comm: kworker/15:1 Tainted: G B W 5.0.0-vanilla+ #3 [ 561.791363] Hardware name: Lenovo ThinkSystem SR650 -[7X05CTO1WW]-/-[7X05CTO1WW]-, BIOS -[IVE136T-2.10]- 03/22/2019 [ 561.791371] Workqueue: events cache_set_flush [bcache] [ 561.791374] RIP: 0010:kthread_stop+0x3b/0x440 [ 561.791376] Code: 00 00 65 8b 05 26 d5 e0 7c 89 c0 48 0f a3 05 ec aa df 02 0f 82 dc 02 00 00 4c 8d 63 20 be 04 00 00 00 4c 89 e7 e8 65 c5 53 00 <f0> ff 43 20 48 8d 7b 24 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 [ 561.791377] RSP: 0018:ffff88872fc8fd10 EFLAGS: 00010286 [ 561.838895] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838916] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838934] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838948] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838966] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838979] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838996] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 563.067028] RAX: 0000000000000000 RBX: fffffffffffffffc RCX: ffffffff832dd314 [ 563.067030] RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000297 [ 563.067032] RBP: ffff88872fc8fe88 R08: fffffbfff0b8213d R09: fffffbfff0b8213d [ 563.067034] R10: 0000000000000001 R11: fffffbfff0b8213c R12: 000000000000001c [ 563.408618] R13: ffff88dc61cc0f68 R14: ffff888102b94900 R15: ffff88dc61cc0f68 [ 563.408620] FS: 0000000000000000(0000) GS:ffff888f7dc00000(0000) knlGS:0000000000000000 [ 563.408622] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 563.408623] CR2: 000000000000001c CR3: 0000000f48a1a004 CR4: 00000000007606e0 [ 563.408625] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 563.408627] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 563.904795] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 563.915796] PKRU: 55555554 [ 563.915797] Call Trace: [ 563.915807] cache_set_flush+0xd4/0x6d0 [bcache] [ 563.915812] process_one_work+0x856/0x1620 [ 564.001226] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 564.033563] ? find_held_lock+0x39/0x1d0 [ 564.033567] ? drain_workqueue+0x380/0x380 [ 564.033574] worker_thread+0x87/0xb80 [ 564.062823] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 564.118042] ? __kthread_parkme+0xb6/0x180 [ 564.118046] ? process_one_work+0x1620/0x1620 [ 564.118048] kthread+0x326/0x3e0 [ 564.118050] ? kthread_create_worker_on_cpu+0xc0/0xc0 [ 564.167066] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 564.252441] ret_from_fork+0x3a/0x50 [ 564.252447] Modules linked in: msr rpcrdma sunrpc rdma_ucm ib_iser ib_umad rdma_cm ib_ipoib i40iw configfs iw_cm ib_cm libiscsi scsi_transport_iscsi mlx4_ib ib_uverbs mlx4_en ib_core nls_iso8859_1 nls_cp437 vfat fat intel_rapl skx_edac x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel ses raid0 aesni_intel cdc_ether enclosure usbnet ipmi_ssif joydev aes_x86_64 i40e scsi_transport_sas mii bcache md_mod crypto_simd mei_me ioatdma crc64 ptp cryptd pcspkr i2c_i801 mlx4_core glue_helper pps_core mei lpc_ich dca wmi ipmi_si ipmi_devintf nd_pmem dax_pmem nd_btt ipmi_msghandler device_dax pcc_cpufreq button hid_generic usbhid mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect xhci_pci sysimgblt fb_sys_fops xhci_hcd ttm megaraid_sas drm usbcore nfit libnvdimm sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua efivarfs [ 564.299390] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 564.348360] CR2: 000000000000001c [ 564.348362] ---[ end trace b7f0e5cc7b2103b0 ]--- Therefore, it is not enough to only check whether c->gc_thread is NULL, we should use IS_ERR_OR_NULL() to check both NULL pointer and error value. This patch changes the above buggy code piece in this way, if (!IS_ERR_OR_NULL(c->gc_thread)) kthread_stop(c->gc_thread); Signed-off-by:
-
Coly Li authored
[ Upstream commit 80265d8d ] When enable lockdep engine, a lockdep warning can be observed when reboot or shutdown system, [ 3142.764557][ T1] bcache: bcache_reboot() Stopping all devices: [ 3142.776265][ T2649] [ 3142.777159][ T2649] ====================================================== [ 3142.780039][ T2649] WARNING: possible circular locking dependency detected [ 3142.782869][ T2649] 5.2.0-rc4-lp151.20-default+ #1 Tainted: G W [ 3142.785684][ T2649] ------------------------------------------------------ [ 3142.788479][ T2649] kworker/3:67/2649 is trying to acquire lock: [ 3142.790738][ T2649] 00000000aaf02291 ((wq_completion)bcache_writeback_wq){+.+.}, at: flush_workqueue+0x87/0x4c0 [ 3142.794678][ T2649] [ 3142.794678][ T2649] but task is already holding lock: [ 3142.797402][ T2649] 000000004fcf89c5 (&bch_register_lock){+.+.}, at: cached_dev_free+0x17/0x120 [bcache] [ 3142.801462][ T2649] [ 3142.801462][ T2649] which lock already depends on the new lock. [ 3142.801462][ T2649] [ 3142.805277][ T2649] [ 3142.805277][ T2649] the existing dependency chain (in reverse order) is: [ 3142.808902][ T2649] [ 3142.808902][ T2649] -> #2 (&bch_register_lock){+.+.}: [ 3142.812396][ T2649] __mutex_lock+0x7a/0x9d0 [ 3142.814184][ T2649] cached_dev_free+0x17/0x120 [bcache] [ 3142.816415][ T2649] process_one_work+0x2a4/0x640 [ 3142.818413][ T2649] worker_thread+0x39/0x3f0 [ 3142.820276][ T2649] kthread+0x125/0x140 [ 3142.822061][ T2649] ret_from_fork+0x3a/0x50 [ 3142.823965][ T2649] [ 3142.823965][ T2649] -> #1 ((work_completion)(&cl->work)#2){+.+.}: [ 3142.827244][ T2649] process_one_work+0x277/0x640 [ 3142.829160][ T2649] worker_thread+0x39/0x3f0 [ 3142.830958][ T2649] kthread+0x125/0x140 [ 3142.832674][ T2649] ret_from_fork+0x3a/0x50 [ 3142.834915][ T2649] [ 3142.834915][ T2649] -> #0 ((wq_completion)bcache_writeback_wq){+.+.}: [ 3142.838121][ T2649] lock_acquire+0xb4/0x1c0 [ 3142.840025][ T2649] flush_workqueue+0xae/0x4c0 [ 3142.842035][ T2649] drain_workqueue+0xa9/0x180 [ 3142.844042][ T2649] destroy_workqueue+0x17/0x250 [ 3142.846142][ T2649] cached_dev_free+0x52/0x120 [bcache] [ 3142.848530][ T2649] process_one_work+0x2a4/0x640 [ 3142.850663][ T2649] worker_thread+0x39/0x3f0 [ 3142.852464][ T2649] kthread+0x125/0x140 [ 3142.854106][ T2649] ret_from_fork+0x3a/0x50 [ 3142.855880][ T2649] [ 3142.855880][ T2649] other info that might help us debug this: [ 3142.855880][ T2649] [ 3142.859663][ T2649] Chain exists of: [ 3142.859663][ T2649] (wq_completion)bcache_writeback_wq --> (work_completion)(&cl->work)#2 --> &bch_register_lock [ 3142.859663][ T2649] [ 3142.865424][ T2649] Possible unsafe locking scenario: [ 3142.865424][ T2649] [ 3142.868022][ T2649] CPU0 CPU1 [ 3142.869885][ T2649] ---- ---- [ 3142.871751][ T2649] lock(&bch_register_lock); [ 3142.873379][ T2649] lock((work_completion)(&cl->work)#2); [ 3142.876399][ T2649] lock(&bch_register_lock); [ 3142.879727][ T2649] lock((wq_completion)bcache_writeback_wq); [ 3142.882064][ T2649] [ 3142.882064][ T2649] *** DEADLOCK *** [ 3142.882064][ T2649] [ 3142.885060][ T2649] 3 locks held by kworker/3:67/2649: [ 3142.887245][ T2649] #0: 00000000e774cdd0 ((wq_completion)events){+.+.}, at: process_one_work+0x21e/0x640 [ 3142.890815][ T2649] #1: 00000000f7df89da ((work_completion)(&cl->work)#2){+.+.}, at: process_one_work+0x21e/0x640 [ 3142.894884][ T2649] #2: 000000004fcf89c5 (&bch_register_lock){+.+.}, at: cached_dev_free+0x17/0x120 [bcache] [ 3142.898797][ T2649] [ 3142.898797][ T2649] stack backtrace: [ 3142.900961][ T2649] CPU: 3 PID: 2649 Comm: kworker/3:67 Tainted: G W 5.2.0-rc4-lp151.20-default+ #1 [ 3142.904789][ T2649] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/13/2018 [ 3142.909168][ T2649] Workqueue: events cached_dev_free [bcache] [ 3142.911422][ T2649] Call Trace: [ 3142.912656][ T2649] dump_stack+0x85/0xcb [ 3142.914181][ T2649] print_circular_bug+0x19a/0x1f0 [ 3142.916193][ T2649] __lock_acquire+0x16cd/0x1850 [ 3142.917936][ T2649] ? __lock_acquire+0x6a8/0x1850 [ 3142.919704][ T2649] ? lock_acquire+0xb4/0x1c0 [ 3142.921335][ T2649] ? find_held_lock+0x34/0xa0 [ 3142.923052][ T2649] lock_acquire+0xb4/0x1c0 [ 3142.924635][ T2649] ? flush_workqueue+0x87/0x4c0 [ 3142.926375][ T2649] flush_workqueue+0xae/0x4c0 [ 3142.928047][ T2649] ? flush_workqueue+0x87/0x4c0 [ 3142.929824][ T2649] ? drain_workqueue+0xa9/0x180 [ 3142.931686][ T2649] drain_workqueue+0xa9/0x180 [ 3142.933534][ T2649] destroy_workqueue+0x17/0x250 [ 3142.935787][ T2649] cached_dev_free+0x52/0x120 [bcache] [ 3142.937795][ T2649] process_one_work+0x2a4/0x640 [ 3142.939803][ T2649] worker_thread+0x39/0x3f0 [ 3142.941487][ T2649] ? process_one_work+0x640/0x640 [ 3142.943389][ T2649] kthread+0x125/0x140 [ 3142.944894][ T2649] ? kthread_create_worker_on_cpu+0x70/0x70 [ 3142.947744][ T2649] ret_from_fork+0x3a/0x50 [ 3142.970358][ T2649] bcache: bcache_device_free() bcache0 stopped Here is how the deadlock happens. 1) bcache_reboot() calls bcache_device_stop(), then inside bcache_device_stop() BCACHE_DEV_CLOSING bit is set on d->flags. Then closure_queue(&d->cl) is called to invoke cached_dev_flush(). 2) In cached_dev_flush(), cached_dev_free() is called by continu_at(). 3) In cached_dev_free(), when stopping the writeback kthread of the cached device by kthread_stop(), dc->writeback_thread will be waken up to quite the kthread while-loop, then cached_dev_put() is called in bch_writeback_thread(). 4) Calling cached_dev_put() in writeback kthread may drop dc->count to 0, then dc->detach kworker is scheduled, which is initialized as cached_dev_detach_finish(). 5) Inside cached_dev_detach_finish(), the last line of code is to call closure_put(&dc->disk.cl), which drops the last reference counter of closrure dc->disk.cl, then the callback cached_dev_flush() gets called. Now cached_dev_flush() is called for second time in the code path, the first time is in step 2). And again bch_register_lock will be acquired again, and a A-A lock (lockdep terminology) is happening. The root cause of the above A-A lock is in cached_dev_free(), mutex bch_register_lock is held before stopping writeback kthread and other kworkers. Fortunately now we have variable 'bcache_is_reboot', which may prevent device registration or unregistration during reboot/shutdown time, so it is unncessary to hold bch_register_lock such early now. This is how this patch fixes the reboot/shutdown time A-A lock issue: After moving mutex_lock(&bch_register_lock) to a later location where before atomic_read(&dc->running) in cached_dev_free(), such A-A lock problem can be solved without any reboot time registration race. Signed-off-by:
-
Coly Li authored
[ Upstream commit 383ff218 ] When too many I/O errors happen on cache set and CACHE_SET_IO_DISABLE bit is set, bch_journal() may continue to work because the journaling bkey might be still in write set yet. The caller of bch_journal() may believe the journal still work but the truth is in-memory journal write set won't be written into cache device any more. This behavior may introduce potential inconsistent metadata status. This patch checks CACHE_SET_IO_DISABLE bit at the head of bch_journal(), if the bit is set, bch_journal() returns NULL immediately to notice caller to know journal does not work. Signed-off-by:
-
Coly Li authored
[ Upstream commit e775339e ] If CACHE_SET_IO_DISABLE of a cache set flag is set by too many I/O errors, currently allocator routines can still continue allocate space which may introduce inconsistent metadata state. This patch checkes CACHE_SET_IO_DISABLE bit in following allocator routines, - bch_bucket_alloc() - __bch_bucket_alloc_set() Once CACHE_SET_IO_DISABLE is set on cache set, the allocator routines may reject allocation request earlier to avoid potential inconsistent metadata. Signed-off-by:
-
Eiichi Tsukata authored
[ Upstream commit d8655e76 ] Commit 9da21b15 ("EDAC: Poll timeout cannot be zero, p2") assumes edac_mc_poll_msec to be unsigned long, but the type of the variable still remained as int. Setting edac_mc_poll_msec can trigger out-of-bounds write. Reproducer: # echo 1001 > /sys/module/edac_core/parameters/edac_mc_poll_msec KASAN report: BUG: KASAN: global-out-of-bounds in edac_set_poll_msec+0x140/0x150 Write of size 8 at addr ffffffffb91b2d00 by task bash/1996 CPU: 1 PID: 1996 Comm: bash Not tainted 5.2.0-rc6+ #23 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014 Call Trace: dump_stack+0xca/0x13e print_address_description.cold+0x5/0x246 __kasan_report.cold+0x75/0x9a ? edac_set_poll_msec+0x140/0x150 kasan_report+0xe/0x20 edac_set_poll_msec+0x140/0x150 ? dimmdev_location_show+0x30/0x30 ? vfs_lock_file+0xe0/0xe0 ? _raw_spin_lock+0x87/0xe0 param_attr_store+0x1b5/0x310 ? param_array_set+0x4f0/0x4f0 module_attr_store+0x58/0x80 ? module_attr_show+0x80/0x80 sysfs_kf_write+0x13d/0x1a0 kernfs_fop_write+0x2bc/0x460 ? sysfs_kf_bin_read+0x270/0x270 ? kernfs_notify+0x1f0/0x1f0 __vfs_write+0x81/0x100 vfs_write+0x1e1/0x560 ksys_write+0x126/0x250 ? __ia32_sys_read+0xb0/0xb0 ? do_syscall_64+0x1f/0x390 do_syscall_64+0xc1/0x390 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7fa7caa5e970 Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 04 RSP: 002b:00007fff6acfdfe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fa7caa5e970 RDX: 0000000000000005 RSI: 0000000000e95c08 RDI: 0000000000000001 RBP: 0000000000e95c08 R08: 00007fa7cad1e760 R09: 00007fa7cb36a700 R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000005 R13: 0000000000000001 R14: 00007fa7cad1d600 R15: 0000000000000005 The buggy address belongs to the variable: edac_mc_poll_msec+0x0/0x40 Memory state around the buggy address: ffffffffb91b2c00: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa ffffffffb91b2c80: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa >ffffffffb91b2d00: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa ^ ffffffffb91b2d80: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00 ffffffffb91b2e00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Fix it by changing the type of edac_mc_poll_msec to unsigned int. The reason why this patch adopts unsigned int rather than unsigned long is msecs_to_jiffies() assumes arg to be unsigned int. We can avoid integer conversion bugs and unsigned int will be large enough for edac_mc_poll_msec. Reviewed-by:
James Morse <james.morse@arm.com> Fixes: 9da21b15 ("EDAC: Poll timeout cannot be zero, p2") Signed-off-by:
Eiichi Tsukata <devel@etsukata.com> Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
-
Ahmad Masri authored
[ Upstream commit 1a276003 ] This change fixes a rare race condition of handling WMI events after wmi_call expires. wmi_recv_cmd immediately handles an event when reply_buf is defined and a wmi_call is waiting for the event. However, in case the wmi_call has already timed-out, there will be no waiting/running wmi_call and the event will be queued in WMI queue and will be handled later in wmi_event_handle. Meanwhile, a new similar wmi_call for the same command and event may be issued. In this case, when handling the queued event we got WARN_ON printed. Fixing this case as a valid timeout and drop the unexpected event. Signed-off-by:
Ahmad Masri <amasri@codeaurora.org> Signed-off-by:
Maya Erez <merez@codeaurora.org> Signed-off-by:
-
Zefir Kurtisi authored
[ Upstream commit df5c4150 ] In commit 3c0efb74 ("ath9k: discard undersized packets") the lower bound of RX packets was set to 10 (min ACK size) to filter those that would otherwise be treated as invalid at mac80211. Alas, short radar pulses are reported as PHY_ERROR frames with length set to 3. Therefore their detection stopped working after that commit. NOTE: ath9k drivers built thereafter will not pass DFS certification. This extends the criteria for short packets to explicitly handle PHY_ERROR frames. Fixes: 3c0efb74 ("ath9k: discard undersized packets") Signed-off-by:
Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 90acc065 ] Build testing with some core crypto options disabled revealed a few modules that are missing CRYPTO_HASH: crypto/asymmetric_keys/x509_public_key.o: In function `x509_get_sig_params': x509_public_key.c:(.text+0x4c7): undefined reference to `crypto_alloc_shash' x509_public_key.c:(.text+0x5e5): undefined reference to `crypto_shash_digest' crypto/asymmetric_keys/pkcs7_verify.o: In function `pkcs7_digest.isra.0': pkcs7_verify.c:(.text+0xab): undefined reference to `crypto_alloc_shash' pkcs7_verify.c:(.text+0x1b2): undefined reference to `crypto_shash_digest' pkcs7_verify.c:(.text+0x3c1): undefined reference to `crypto_shash_update' pkcs7_verify.c:(.text+0x411): undefined reference to `crypto_shash_finup' This normally doesn't show up in randconfig tests because there is a large number of other options that select CRYPTO_HASH. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 47397118 ] The same bug that gcc hit in the past is apparently now showing up with clang, which decides to inline __serpent_setkey_sbox: crypto/serpent_generic.c:268:5: error: stack frame size of 2112 bytes in function '__serpent_setkey' [-Werror,-Wframe-larger-than=] Marking it 'noinline' reduces the stack usage from 2112 bytes to 192 and 96 bytes, respectively, and seems to generate more useful object code. Fixes: c871c10e ("crypto: serpent - improve __serpent_setkey with UBSAN") Signed-off-by:
Eric Biggers <ebiggers@kernel.org> Signed-off-by:
-
Mauro S. M. Rodrigues authored
[ Upstream commit 655c9141 ] Some transceivers may comply with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM) interface described in it. The existence of such area is specified by bit 6 of byte 92, set to 1 if implemented. Currently, due to not checking this bit ixgbe fails trying to read SFP module's eeprom with the follow message: ethtool -m enP51p1s0f0 Cannot get Module EEPROM data: Input/output error Because it fails to read the additional 256 bytes in which it was assumed to exist the DDM data. This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom data was confirmed by Mellanox as correct and present in other Passive DACs in from other manufacturers. Signed-off-by:
"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com> Reviewed-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Jianbo Liu authored
[ Upstream commit f53297d6 ] The ingress and egress ACL root namespaces are created per vport and stored into arrays. However, the vport number is not the same as the index. Passing the array index, instead of vport number, to get the correct ingress and egress acl namespace. Fixes: 9b93ab98 ("net/mlx5: Separate ingress/egress namespaces for each vport") Signed-off-by:
Jianbo Liu <jianbol@mellanox.com> Reviewed-by:
Oz Shlomo <ozsh@mellanox.com> Reviewed-by:
Eli Britstein <elibr@mellanox.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Reviewed-by:
Mark Bloch <markb@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Waibel Georg authored
[ Upstream commit 025bf377 ] In case the requested gpio property is not found in the device tree, some callers of gpiod_get_from_of_node() expect a return value of NULL, others expect -ENOENT. In particular devm_fwnode_get_index_gpiod_from_child() expects -ENOENT. Currently it gets a NULL, which breaks the loop that tries all gpio_suffixes. The result is that a gpio property is not found, even though it is there. This patch changes gpiod_get_from_of_node() to return -ENOENT instead of NULL when the requested gpio property is not found in the device tree. Additionally it modifies all calling functions to properly evaluate the return value. Another approach would be to leave the return value of gpiod_get_from_of_node() as is and fix the bug in devm_fwnode_get_index_gpiod_from_child(). Other callers would still need to be reworked. The effort would be the same as with the chosen solution. Signed-off-by:
Georg Waibel <georg.waibel@sensor-technik.de> Reviewed-by:
Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Ferdinand Blomqvist authored
[ Upstream commit ef4d6a85 ] Check if the syndrome provided by the caller is zero, and act accordingly. Signed-off-by:
Ferdinand Blomqvist <ferdinand.blomqvist@gmail.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190620141039.9874-6-ferdinand.blomqvist@gmail.comSigned-off-by:
-
Jiong Wang authored
[ Upstream commit 75672dda ] Yauheni reported the following code do not work correctly on BE arches: ALU_ARSH_X: DST = (u64) (u32) ((*(s32 *) &DST) >> SRC); CONT; ALU_ARSH_K: DST = (u64) (u32) ((*(s32 *) &DST) >> IMM); CONT; and are causing failure of test_verifier test 'arsh32 on imm 2' on BE arches. The code is taking address and interpreting memory directly, so is not endianness neutral. We should instead perform standard C type casting on the variable. A u64 to s32 conversion will drop the high 32-bit and reserve the low 32-bit as signed integer, this is all we want. Fixes: 2dc6b100 ("bpf: interpreter support BPF_ALU | BPF_ARSH") Reported-by:
Yauheni Kaliuta <yauheni.kaliuta@redhat.com> Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by:
Jiong Wang <jiong.wang@netronome.com> Acked-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Ferdinand Blomqvist authored
[ Upstream commit 2034a42d ] The decoding of shortenend codes is broken. It only works as expected if there are no erasures. When decoding with erasures, Lambda (the error and erasure locator polynomial) is initialized from the given erasure positions. The pad parameter is not accounted for by the initialisation code, and hence Lambda is initialized from incorrect erasure positions. The fix is to adjust the erasure positions by the supplied pad. Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit f7019b7b ] Clang warns: In file included from net/xdp/xsk_queue.c:10: net/xdp/xsk_queue.h:292:2: warning: expression result unused [-Wunused-value] WRITE_ONCE(q->ring->producer, q->prod_tail); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ include/linux/compiler.h:284:6: note: expanded from macro 'WRITE_ONCE' __u.__val; \ ~~~ ^~~~~ 1 warning generated. The q->prod_tail assignment has a comma at the end, not a semi-colon. Fix that so clang no longer warns and everything works as expected. Fixes: c497176c ("xsk: add Rx receive functions and poll support") Link: https://github.com/ClangBuiltLinux/linux/issues/544Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Acked-by:
Nick Desaulniers <ndesaulniers@google.com> Acked-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by:
Björn Töpel <bjorn.topel@intel.com> Acked-by:
-
Felix Kaechele authored
[ Upstream commit e7600865 ] Commit f8e60898 ("netfilter: ctnetlink: Resolve conntrack L3-protocol flush regression") introduced a regression in which deletion of conntrack entries would fail because the L3 protocol information is replaced by AF_UNSPEC. As a result the search for the entry to be deleted would turn up empty due to the tuple used to perform the search is now different from the tuple used to initially set up the entry. For flushing the conntrack table we do however want to keep the option for nfgenmsg->version to have a non-zero value to allow for newer user-space tools to request treatment under the new behavior. With that it is possible to independently flush tables for a defined L3 protocol. This was introduced with the enhancements in in commit 59c08c69 ("netfilter: ctnetlink: Support L3 protocol-filter on flush"). Older user-space tools will retain the behavior of flushing all tables regardless of defined L3 protocol. Fixes: f8e60898 ("netfilter: ctnetlink: Resolve conntrack L3-protocol flush regression") Suggested-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
Felix Kaechele <felix@kaechele.ca> Signed-off-by:
-
Marek Szyprowski authored
[ Upstream commit 6282edb7 ] Exynos SoCs based on CA7/CA15 have 2 timer interfaces: custom Exynos MCT (Multi Core Timer) and standard ARM Architected Timers. There are use cases, where both timer interfaces are used simultanously. One of such examples is using Exynos MCT for the main system timer and ARM Architected Timers for the KVM and virtualized guests (KVM requires arch timers). Exynos Multi-Core Timer driver (exynos_mct) must be however started before ARM Architected Timers (arch_timer), because they both share some common hardware blocks (global system counter) and turning on MCT is needed to get ARM Architected Timer working properly. To ensure selecting Exynos MCT as the main system timer, increase MCT timer rating. To ensure proper starting order of both timers during suspend/resume cycle, increase MCT hotplug priority over ARM Archictected Timers. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Dmitry Osipenko authored
[ Upstream commit fc9babc2 ] We're adjusting the timer's base for each per-CPU timer to point to the actual start of the timer since device-tree defines a compound registers range that includes all of the timers. In this case the original base need to be restore before calling iounmap to unmap the proper address. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Acked-by:
Jon Hunter <jonathanh@nvidia.com> Acked-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Tejun Heo authored
[ Upstream commit ca156e00 ] ZAC support added sense data requesting on error for both ZAC and ATA devices. This seems to cause erratic error handling behaviors on some SSDs where the device reports sense data availability and then delivers the wrong content making EH take the wrong actions. The failure mode was sporadic on a LITE-ON ssd and couldn't be reliably reproduced. There is no value in requesting sense data from non-ZAC ATA devices while there's a significant risk of introducing EH misbehaviors which are difficult to reproduce and fix. Let's do the sense data dancing only for ZAC devices. Reviewed-by:
Hannes Reinecke <hare@suse.com> Tested-by:
Masato Suzuki <masato.suzuki@wdc.com> Reviewed-by:
Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Dmitry Osipenko authored
[ Upstream commit 7a391670 ] Release all requested IRQ's on the request error to properly clean up allocated resources. Signed-off-by:
Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by:
-
Amadeusz Sławiński authored
[ Upstream commit 0f6ff785 ] When we unload Skylake driver we may end up calling hdac_component_master_unbind(), it uses acomp->audio_ops, which we set in hdmi_codec_probe(), so we need to set it to NULL in hdmi_codec_remove(), otherwise we will dereference no longer existing pointer. Signed-off-by:
Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
-
Kyle Meyer authored
[ Upstream commit 9f94c7f9 ] Attempting to profile 1024 or more CPUs with perf causes two errors: perf record -a [ perf record: Woken up X times to write data ] way too many cpu caches.. [ perf record: Captured and wrote X MB perf.data (X samples) ] perf report -C 1024 Error: failed to set cpu bitmap Requested CPU 1024 too large. Consider raising MAX_NR_CPUS Increasing MAX_NR_CPUS from 1024 to 2048 and redefining MAX_CACHES as MAX_NR_CPUS * 4 returns normal functionality to perf: perf record -a [ perf record: Woken up X times to write data ] [ perf record: Captured and wrote X MB perf.data (X samples) ] perf report -C 1024 ... Signed-off-by:
Kyle Meyer <kyle.meyer@hpe.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20190620193630.154025-1-meyerk@stormcage.eag.rdlabs.hpecorp.netSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Miaoqing Pan authored
[ Upstream commit 011d4111 ] Observed PCIE device wake up failed after ~120 iterations of soft-reboot test. The error message is "ath10k_pci 0000:01:00.0: failed to wake up device : -110" The call trace as below: ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait -> ath10k_pci_is_awake Once trigger the device to wake up, we will continuously check the RTC state until it returns RTC_STATE_V_ON or timeout. But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON. Occasionally, we get 0x7 on the fist read, we thought as a failure case, but actually is the right value, also verified with the spec. So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed ~2000 iterations. Tested HW: QCA9984 Signed-off-by:
Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by:
-
Miaoqing Pan authored
[ Upstream commit 08d80e4c ] On SMP platform, when continuously running wifi up/down, the napi poll can be scheduled during chip reset, which will call ath10k_pci_has_fw_crashed() to check the fw status. But in the reset period, the value from FW_INDICATOR_ADDRESS register will return 0xdeadbeef, which also be treated as fw crash. Fix the issue by moving chip reset after napi disabled. ath10k_pci 0000:01:00.0: firmware crashed! (guid 73b30611-5b1e-4bdd-90b4-64c81eb947b6) ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1 ath10k_pci 0000:01:00.0: failed to get memcpy hi address for firmware address 4: -16 ath10k_pci 0000:01:00.0: failed to read firmware dump area: -16 ath10k_pci 0000:01:00.0: Copy Engine register dump: ath10k_pci 0000:01:00.0: [00]: 0x0004a000 0 0 0 0 ath10k_pci 0000:01:00.0: [01]: 0x0004a400 0 0 0 0 ath10k_pci 0000:01:00.0: [02]: 0x0004a800 0 0 0 0 ath10k_pci 0000:01:00.0: [03]: 0x0004ac00 0 0 0 0 ath10k_pci 0000:01:00.0: [04]: 0x0004b000 0 0 0 0 ath10k_pci 0000:01:00.0: [05]: 0x0004b400 0 0 0 0 ath10k_pci 0000:01:00.0: [06]: 0x0004b800 0 0 0 0 ath10k_pci 0000:01:00.0: [07]: 0x0004bc00 1 0 1 0 ath10k_pci 0000:01:00.0: [08]: 0x0004c000 0 0 0 0 ath10k_pci 0000:01:00.0: [09]: 0x0004c400 0 0 0 0 ath10k_pci 0000:01:00.0: [10]: 0x0004c800 0 0 0 0 ath10k_pci 0000:01:00.0: [11]: 0x0004cc00 0 0 0 0 Tested HW: QCA9984,QCA9887,WCN3990 Signed-off-by:
-
Claire Chang authored
[ Upstream commit 4b553f3c ] In function ath10k_sdio_mbox_rx_alloc() [sdio.c], ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases. This will make the driver think the allocation for skb is successful and try to access the skb. If we enable failslab, system will easily crash with NULL pointer dereferencing. Call trace of CONFIG_FAILSLAB: ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio] process_sdio_pending_irqs+0x4c/0x174 sdio_run_irqs+0x3c/0x64 sdio_irq_work+0x1c/0x28 Fixes: d96db25d ("ath10k: add initial SDIO support") Signed-off-by:
Claire Chang <tientzu@chromium.org> Reviewed-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
-
Julian Anastasov authored
[ Upstream commit 5db7c8b9 ] syzkaller reports for memory leak in start_sync_thread [1] As Eric points out, kthread may start and stop before the threadfn function is called, so there is no chance the data (tinfo in our case) to be released in thread. Fix this by releasing tinfo in the controlling code instead. [1] BUG: memory leak unreferenced object 0xffff8881206bf700 (size 32): comm "syz-executor761", pid 7268, jiffies 4294943441 (age 20.470s) hex dump (first 32 bytes): 00 40 7c 09 81 88 ff ff 80 45 b8 21 81 88 ff ff .@|......E.!.... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<0000000057619e23>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline] [<0000000057619e23>] slab_post_alloc_hook mm/slab.h:439 [inline] [<0000000057619e23>] slab_alloc mm/slab.c:3326 [inline] [<0000000057619e23>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553 [<0000000086ce5479>] kmalloc include/linux/slab.h:547 [inline] [<0000000086ce5479>] start_sync_thread+0x5d2/0xe10 net/netfilter/ipvs/ip_vs_sync.c:1862 [<000000001a9229cc>] do_ip_vs_set_ctl+0x4c5/0x780 net/netfilter/ipvs/ip_vs_ctl.c:2402 [<00000000ece457c8>] nf_sockopt net/netfilter/nf_sockopt.c:106 [inline] [<00000000ece457c8>] nf_setsockopt+0x4c/0x80 net/netfilter/nf_sockopt.c:115 [<00000000942f62d4>] ip_setsockopt net/ipv4/ip_sockglue.c:1258 [inline] [<00000000942f62d4>] ip_setsockopt+0x9b/0xb0 net/ipv4/ip_sockglue.c:1238 [<00000000a56a8ffd>] udp_setsockopt+0x4e/0x90 net/ipv4/udp.c:2616 [<00000000fa895401>] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3130 [<0000000095eef4cf>] __sys_setsockopt+0x98/0x120 net/socket.c:2078 [<000000009747cf88>] __do_sys_setsockopt net/socket.c:2089 [inline] [<000000009747cf88>] __se_sys_setsockopt net/socket.c:2086 [inline] [<000000009747cf88>] __x64_sys_setsockopt+0x26/0x30 net/socket.c:2086 [<00000000ded8ba80>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301 [<00000000893b4ac8>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported-by: syzbot+7e2e50c8adfccd2e5041@syzkaller.appspotmail.com Suggested-by:
Julian Anastasov <ja@ssi.bg> Acked-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Lorenzo Bianconi authored
[ Upstream commit 23377c20 ] When the device is disconnected while passing traffic it is possible to receive out of order urbs causing a memory leak since the skb linked to the current tx urb is not removed. Fix the issue deallocating the skb cleaning up the tx ring. Moreover this patch fixes the following kernel warning [ 57.480771] usb 1-1: USB disconnect, device number 2 [ 57.483451] ------------[ cut here ]------------ [ 57.483462] TX urb mismatch [ 57.483481] WARNING: CPU: 1 PID: 32 at drivers/net/wireless/mediatek/mt7601u/dma.c:245 mt7601u_complete_tx+0x165/00 [ 57.483483] Modules linked in: [ 57.483496] CPU: 1 PID: 32 Comm: kworker/1:1 Not tainted 5.2.0-rc1+ #72 [ 57.483498] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-2.fc30 04/01/2014 [ 57.483502] Workqueue: usb_hub_wq hub_event [ 57.483507] RIP: 0010:mt7601u_complete_tx+0x165/0x1e0 [ 57.483510] Code: 8b b5 10 04 00 00 8b 8d 14 04 00 00 eb 8b 80 3d b1 cb e1 00 00 75 9e 48 c7 c7 a4 ea 05 82 c6 05 f [ 57.483513] RSP: 0000:ffffc900000a0d28 EFLAGS: 00010092 [ 57.483516] RAX: 000000000000000f RBX: ffff88802c0a62c0 RCX: ffffc900000a0c2c [ 57.483518] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff810a8371 [ 57.483520] RBP: ffff88803ced6858 R08: 0000000000000000 R09: 0000000000000001 [ 57.483540] R10: 0000000000000002 R11: 0000000000000000 R12: 0000000000000046 [ 57.483542] R13: ffff88802c0a6c88 R14: ffff88803baab540 R15: ffff88803a0cc078 [ 57.483548] FS: 0000000000000000(0000) GS:ffff88803eb00000(0000) knlGS:0000000000000000 [ 57.483550] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 57.483552] CR2: 000055e7f6780100 CR3: 0000000028c86000 CR4: 00000000000006a0 [ 57.483554] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 57.483556] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 57.483559] Call Trace: [ 57.483561] <IRQ> [ 57.483565] __usb_hcd_giveback_urb+0x77/0xe0 [ 57.483570] xhci_giveback_urb_in_irq.isra.0+0x8b/0x140 [ 57.483574] handle_cmd_completion+0xf5b/0x12c0 [ 57.483577] xhci_irq+0x1f6/0x1810 [ 57.483581] ? lockdep_hardirqs_on+0x9e/0x180 [ 57.483584] ? _raw_spin_unlock_irq+0x24/0x30 [ 57.483588] __handle_irq_event_percpu+0x3a/0x260 [ 57.483592] handle_irq_event_percpu+0x1c/0x60 [ 57.483595] handle_irq_event+0x2f/0x4c [ 57.483599] handle_edge_irq+0x7e/0x1a0 [ 57.483603] handle_irq+0x17/0x20 [ 57.483607] do_IRQ+0x54/0x110 [ 57.483610] common_interrupt+0xf/0xf [ 57.483612] </IRQ> Acked-by:
Jakub Kicinski <kubakici@wp.pl> Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Masahiro Yamada authored
[ Upstream commit bc53d3d7 ] Without 'set -e', shell scripts continue running even after any error occurs. The missed 'set -e' is a typical bug in shell scripting. For example, when a disk space shortage occurs while this script is running, it actually ends up with generating a truncated capflags.c. Yet, mkcapflags.sh continues running and exits with 0. So, the build system assumes it has succeeded. It will not be re-generated in the next invocation of Make since its timestamp is newer than that of any of the source files. Add 'set -e' so that any error in this script is caught and propagated to the build system. Since 9c2af1c7 ("kbuild: add .DELETE_ON_ERROR special target"), make automatically deletes the target on any failure. So, the broken capflags.c will be deleted automatically. Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Lorenzo Bianconi authored
[ Upstream commit 4079e8cc ] Do not schedule rx_tasklet when the usb dongle is disconnected. Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb can run concurrently with urb completion and we can unlink urbs from rx ring in any order. This patch fixes the common kernel warning reported when the device is removed. [ 24.921354] usb 3-14: USB disconnect, device number 7 [ 24.921593] ------------[ cut here ]------------ [ 24.921594] RX urb mismatch [ 24.921675] WARNING: CPU: 4 PID: 163 at drivers/net/wireless/mediatek/mt7601u/dma.c:200 mt7601u_complete_rx+0xcb/0xd0 [mt7601u] [ 24.921769] CPU: 4 PID: 163 Comm: kworker/4:2 Tainted: G OE 4.19.31-041931-generic #201903231635 [ 24.921770] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P1.30 05/23/2014 [ 24.921782] Workqueue: usb_hub_wq hub_event [ 24.921797] RIP: 0010:mt7601u_complete_rx+0xcb/0xd0 [mt7601u] [ 24.921800] RSP: 0018:ffff9bd9cfd03d08 EFLAGS: 00010086 [ 24.921802] RAX: 0000000000000000 RBX: ffff9bd9bf043540 RCX: 0000000000000006 [ 24.921803] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9bd9cfd16420 [ 24.921804] RBP: ffff9bd9cfd03d28 R08: 0000000000000002 R09: 00000000000003a8 [ 24.921805] R10: 0000002f485fca34 R11: 0000000000000000 R12: ffff9bd9bf043c1c [ 24.921806] R13: ffff9bd9c62fa3c0 R14: 0000000000000082 R15: 0000000000000000 [ 24.921807] FS: 0000000000000000(0000) GS:ffff9bd9cfd00000(0000) knlGS:0000000000000000 [ 24.921808] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 24.921808] CR2: 00007fb2648b0000 CR3: 0000000142c0a004 CR4: 00000000001606e0 [ 24.921809] Call Trace: [ 24.921812] <IRQ> [ 24.921819] __usb_hcd_giveback_urb+0x8b/0x140 [ 24.921821] usb_hcd_giveback_urb+0xca/0xe0 [ 24.921828] xhci_giveback_urb_in_irq.isra.42+0x82/0xf0 [ 24.921834] handle_cmd_completion+0xe02/0x10d0 [ 24.921837] xhci_irq+0x274/0x4a0 [ 24.921838] xhci_msi_irq+0x11/0x20 [ 24.921851] __handle_irq_event_percpu+0x44/0x190 [ 24.921856] handle_irq_event_percpu+0x32/0x80 [ 24.921861] handle_irq_event+0x3b/0x5a [ 24.921867] handle_edge_irq+0x80/0x190 [ 24.921874] handle_irq+0x20/0x30 [ 24.921889] do_IRQ+0x4e/0xe0 [ 24.921891] common_interrupt+0xf/0xf [ 24.921892] </IRQ> [ 24.921900] RIP: 0010:usb_hcd_flush_endpoint+0x78/0x180 [ 24.921354] usb 3-14: USB disconnect, device number 7 Signed-off-by:
-
Ping-Ke Shih authored
[ Upstream commit 6c0ed66f ] rtl_usb_probe() must do error handle rtl_deinit_core() only if rtl_init_core() is done, otherwise goto error_out2. | usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 | rtl_usb: reg 0xf0, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x0 | rtl8192cu: Chip version 0x10 | rtl_usb: reg 0xa, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x0 | rtl_usb: Too few input end points found | INFO: trying to register non-static key. | the code is fine but needs lockdep annotation. | turning off the locking correctness validator. | CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3 | Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS | Google 01/01/2011 | Workqueue: usb_hub_wq hub_event | Call Trace: | __dump_stack lib/dump_stack.c:77 [inline] | dump_stack+0xe8/0x16e lib/dump_stack.c:113 | assign_lock_key kernel/locking/lockdep.c:786 [inline] | register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095 | __lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582 | lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211 | __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] | _raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152 | rtl_c2hcmd_launcher+0xd1/0x390 | drivers/net/wireless/realtek/rtlwifi/base.c:2344 | rtl_deinit_core+0x25/0x2d0 drivers/net/wireless/realtek/rtlwifi/base.c:574 | rtl_usb_probe.cold+0x861/0xa70 | drivers/net/wireless/realtek/rtlwifi/usb.c:1093 | usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361 | really_probe+0x2da/0xb10 drivers/base/dd.c:509 | driver_probe_device+0x21d/0x350 drivers/base/dd.c:671 | __device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778 | bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454 | __device_attach+0x223/0x3a0 drivers/base/dd.c:844 | bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514 | device_add+0xad2/0x16e0 drivers/base/core.c:2106 | usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021 | generic_probe+0xa2/0xda drivers/usb/core/generic.c:210 | usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266 | really_probe+0x2da/0xb10 drivers/base/dd.c:509 | driver_probe_device+0x21d/0x350 drivers/base/dd.c:671 | __device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778 | bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454 | __device_attach+0x223/0x3a0 drivers/base/dd.c:844 | bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514 | device_add+0xad2/0x16e0 drivers/base/core.c:2106 | usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534 | hub_port_connect drivers/usb/core/hub.c:5089 [inline] | hub_port_connect_change drivers/usb/core/hub.c:5204 [inline] | port_event drivers/usb/core/hub.c:5350 [inline] | hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432 | process_one_work+0x90f/0x1580 kernel/workqueue.c:2269 | worker_thread+0x9b/0xe20 kernel/workqueue.c:2415 | kthread+0x313/0x420 kernel/kthread.c:253 | ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352 Reported-by: syzbot+1fcc5ef45175fc774231@syzkaller.appspotmail.com Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Icenowy Zheng authored
[ Upstream commit 0fec7e72 ] The PHY selection bit also exists on SoCs without an internal PHY; if it's set to 1 (internal PHY, default value) then the MAC will not make use of any PHY on such SoCs. This problem appears when adapting for H6, which has no real internal PHY (the "internal PHY" on H6 is not on-die, but on a co-packaged AC200 chip, connected via RMII interface at GPIO bank A). Force the PHY selection bit to 0 when the SOC doesn't have an internal PHY, to address the problem of a wrong default value. Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Signed-off-by:
Ondrej Jirman <megous@megous.com> Signed-off-by:
-
Hans Verkuil authored
[ Upstream commit 6bc5a4a1 ] This driver has three locking issues: - The wait_event_interruptible() condition calls hdpvr_get_next_buffer(dev) which uses a mutex, which is not allowed. Rewrite with list_empty_careful() that doesn't need locking. - In hdpvr_read() the call to hdpvr_stop_streaming() didn't lock io_mutex, but it should have since stop_streaming expects that. - In hdpvr_device_release() io_mutex was locked when calling flush_work(), but there it shouldn't take that mutex since the work done by flush_work() also wants to lock that mutex. There are also two other changes (suggested by Keith): - msecs_to_jiffies(4000); (a NOP) should have been msleep(4000). - Change v4l2_dbg to v4l2_info to always log if streaming had to be restarted. Reported-by:
Keith Pyle <kpyle@austin.rr.com> Suggested-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
André Almeida authored
[ Upstream commit 77ae46e1 ] v4l2_fill_pixfmt() returns -EINVAL if the pixelformat used as parameter is invalid or if the user is trying to use a multiplanar format with the singleplanar API. Currently, the vimc_cap_try_fmt_vid_cap() returns such value, but vimc_cap_s_fmt_vid_cap() is ignoring it. Fix that and returns an error value if vimc_cap_try_fmt_vid_cap() has failed. Signed-off-by:
André Almeida <andrealmeid@collabora.com> Suggested-by:
Helen Koike <helen.koike@collabora.com> Signed-off-by:
-
Philipp Zabel authored
[ Upstream commit b3b7d968 ] If no more frames are decoded in bitstream end mode, and a previously decoded frame has been returned, the firmware still increments the frame number. To avoid a sequence number mismatch after decoder restart, increment the sequence_offset correction parameter. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Marco Felsch authored
[ Upstream commit f3775f89 ] coda_encoder_cmd() is racy, as the last scheduled picture run worker can still be in-flight while the ENC_CMD_STOP command is issued. Depending on the exact timing the sequence numbers might already be changed, but the last buffer might not have been put on the destination queue yet. In this case the current implementation would prematurely wake the destination queue with last_buffer_dequeued=true, causing userspace to call streamoff before the last buffer is handled. Close this race window by synchronizing with the pic_run_worker before doing the sequence check. Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> [l.stach@pengutronix.de: switch to flush_work, reword commit message] Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
