This loop will try to unmap enetc_unmap_tx_buff[-1] and crash.

Fixes: 9d2b68cc ("net: enetc: add support for XDP_REDIRECT")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YHBHfCY/yv3EnM9z@mwandaSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Eliminate the following coccicheck warning:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_u32.c:529:3-9: WARNING:
 NULL check before some freeing functions is not needed.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_u32.c:533:2-8: WARNING:
 NULL check before some freeing functions is not needed.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_cudbg.c:161:2-7: WARNING:
 NULL check before some freeing functions is not needed.
drivers/net/ethernet/chelsio/cxgb4/clip_tbl.c:327:3-9: WARNING:
 NULL check before some freeing functions is not needed.
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Link: https://lore.kernel.org/r/20210409115339.4598-1-linqiheng@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Heiner Kallweit says:

====================
net: make PHY PM ops a no-op if MAC driver manages PHY PM

Resume callback of the PHY driver is called after the one for the MAC
driver. The PHY driver resume callback calls phy_init_hw(), and this is
potentially problematic if the MAC driver calls phy_start() in its resume
callback. One issue was reported with the fec driver and a KSZ8081 PHY
which seems to become unstable if a soft reset is triggered during aneg.

The new flag allows MAC drivers to indicate that they take care of
suspending/resuming the PHY. Then the MAC PM callbacks can handle
any dependency between MAC and PHY PM.
====================

Link: https://lore.kernel.org/r/9e695411-ab1d-34fe-8b90-3e8192ab84f6@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use the new mac_managed_pm flag to indicate that the driver takes care
of PHY power management.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use the new mac_managed_pm flag to work around an issue with KSZ8081 PHY
that becomes unstable when a soft reset is triggered during aneg.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Resume callback of the PHY driver is called after the one for the MAC
driver. The PHY driver resume callback calls phy_init_hw(), and this is
potentially problematic if the MAC driver calls phy_start() in its resume
callback. One issue was reported with the fec driver and a KSZ8081 PHY
which seems to become unstable if a soft reset is triggered during aneg.

The new flag allows MAC drivers to indicate that they take care of
suspending/resuming the PHY. Then the MAC PM callbacks can handle
any dependency between MAC and PHY PM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit e880f8b3.

1) Patch has not been properly tested, and is wrong [1]
2) Patch submission did not include TCP maintainer (this is me)

[1]
divide error: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 8426 Comm: syz-executor478 Not tainted 5.12.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__tcp_select_window+0x56d/0xad0 net/ipv4/tcp_output.c:3015
Code: 44 89 ff e8 d5 cd f0 f9 45 39 e7 0f 8d 20 ff ff ff e8 f7 c7 f0 f9 44 89 e3 e9 13 ff ff ff e8 ea c7 f0 f9 44 89 e0 44 89 e3 99 <f7> 7c 24 04 29 d3 e9 fc fe ff ff e8 d3 c7 f0 f9 41 f7 dc bf 1f 00
RSP: 0018:ffffc9000184fac0 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff87832e76 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff87832e14 R11: 0000000000000000 R12: 0000000000000000
R13: 1ffff92000309f5c R14: 0000000000000000 R15: 0000000000000000
FS:  00000000023eb300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fc2b5f426c0 CR3: 000000001c5cf000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 tcp_select_window net/ipv4/tcp_output.c:264 [inline]
 __tcp_transmit_skb+0xa82/0x38f0 net/ipv4/tcp_output.c:1351
 tcp_transmit_skb net/ipv4/tcp_output.c:1423 [inline]
 tcp_send_active_reset+0x475/0x8e0 net/ipv4/tcp_output.c:3449
 tcp_disconnect+0x15a9/0x1e60 net/ipv4/tcp.c:2955
 inet_shutdown+0x260/0x430 net/ipv4/af_inet.c:905
 __sys_shutdown_sock net/socket.c:2189 [inline]
 __sys_shutdown_sock net/socket.c:2183 [inline]
 __sys_shutdown+0xf1/0x1b0 net/socket.c:2201
 __do_sys_shutdown net/socket.c:2209 [inline]
 __se_sys_shutdown net/socket.c:2207 [inline]
 __x64_sys_shutdown+0x50/0x70 net/socket.c:2207
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Fixes: e880f8b3 ("tcp: Reset tcp connections in SYN-SENT state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Manoj Basapathi <manojbm@codeaurora.org>
Cc: Sauvik Saha <ssaha@codeaurora.org>
Link: https://lore.kernel.org/r/20210409170237.274904-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

DCCP is virtually never used, so no need to use space in struct net for it.

Put the pernet ipv4/v6 socket in the dccp ipv4/ipv6 modules instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20210408174502.1625-1-fw@strlen.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'for-net-next-2021-04-08' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Luiz Augusto von Dentz says:

====================
bluetooth-next pull request for net-next:

 - Proper support for BCM4330 and BMC4334
 - Various improvements for firmware download of Intel controllers
 - Update management interface revision to 20
 - Support for AOSP HCI vendor commands
 - Initial Virtio support
====================
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-04-08

This series contains updates to ice driver only.

Chinh adds retrying of sending some AQ commands when receiving EBUSY
error.

Victor modifies how nodes are added to reduce stack usage.

Ani renames some variables to either follow spec naming or to be inline
with naming in the rest of the driver. Ignores EMODE error as there are
cases where this error is expected. Performs some cleanup such as
removing unnecessary checks, doing variable assignments over copies, and
removing unneeded variables. Revises some error codes returned in link
settings to be more appropriate. He also implements support for new
firmware option to get default link configuration which accounts for
any needed NVM based overrides for PHY configuration. He also removes
the rx_gro_dropped stat as the value no longer changes.

Jeb removes setting specific link modes on firmwares that no longer
require it.

Brett removes unnecessary checks when adding and removing VLANs.

Tony fixes a checkpatch warning for unnecessary blank line.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This cleanup patchset includes the following patches:

 - for kerneldoc in batadv_priv, by Linus Luessing

 - drop unused header preempt.h, by Sven Eckelmann

 - Fix misspelled "wont", by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Buslov says:

====================
Additional tests for action API

Add two new tests for action create/change code.
====================
Acked-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify cleanup of failed actions batch change where second action in batch
fails after successful init of first action.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify cleanup of failed actions batch add where second action in batch
fails after successful init of first action.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: add support for pm_ops

This series adds support for pm_ops in the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To implement the system suspend/resume functions, the NIC driver needs
to support:
1. When the system enters the suspend mode, the driver needs to
implement the suspend callback function of the NIC device. The driver
needs to mute the device, stop all RX/TX activities of the device, and
unmap the interrupt.
2. When the system enters the resume mode, the driver needs to
implement the resume callback function of the NIC device and restore
the device to the state before suspension.

When the system enters the suspend and resume mode, the NIC driver
actually executes the PF function reset process.

When the PFs are suspending/resuming, VFs also enter the suspend/resume
state because the PFs trigger the VFs to reset, therefore no operation
is required when the VF pci_driver is suspending or resuming.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flr_prepare/flr_done functions are not only used in the FLR scenario,
but also used in the suspend/resume.

Change the function names to prepare_for_reset/rebuild_for_reset, change
the flr_prepare/flr_done to reset_prepare/reset_done in hnae3_ae_ops.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: hwstamp tweaks

A few little changes after review comments and
additional internal testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the configuration is locked before
operating on it for the replay.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split the call into ionic_lif_hwstamp_set() to have two
separate interfaces, one from the ioctl() for changing the
configuration and one for replaying the current configuration
after a FW RESET.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

When starting the queues in the link-check, don't go into
the BROKEN state if the return was EBUSY.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

When returning after a firmware reset, re-start the
PTP after we've restarted the general queues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set the SKBTX_IN_PROGRESS when offloading the Tx timestamp.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the device is in a Tx offload mode before calling the
hwstamp offload xmit.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't need to look for HAVE_HWSTAMP_TX_ONESTEP_P2P in the
upstream kernel.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up variable declarations.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek Behún says:

====================
net: phy: marvell10g updates

Here are some updates for marvell10g PHY driver.

I am still working on some more changes for this driver, but I would
like to have at least something reviewed / applied.

Changes since v3:
- added Andrew's Reviewed-by tags
- removed patches adding variadic-macro library and bitmap
  initialization macro - it causes warning that we are not currently
  able to fix easily. Instead the supported_interfaces bitmap is now
  initialized via a chip specific method
- added explanation of mactype initialization to commit message of patch
  07/16
- fixed repeated word in commit message of second to last patch

Changes since v2:
- code refactored to use an additional structure mv3310_chip describing
  mv3310 specific properties / operations for PHYs supported by this
  driver
- added separate phy_driver structures for 88X3340 and 88E2111
- removed 88E2180 specific code (dual-port and quad-port SXGMII modes
  are ignored for now)

Changes since v1:
- added various MACTYPEs support also for 88E21XX
- differentiate between specific models with same PHY_ID
- better check for compatible interface
- print exact model
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add myself as maintainer of the marvell10g ethernet PHY driver, in
addition to Russell King.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This module supports not only Alaska X, but also Alaska M.

Change module description appropriately.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

88E2111 is a variant of 88E2110 which does not support 5 gigabit speeds.

Differentiate these variants via the match_phy_device() method, since
they have the same PHY ID.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add constants for 2.5G and 5G speed in PCS speed register into mdio.h.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver name "mv88x2110" should be instead "mv88e2110".
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 88X3340 contains 4 cores similar to 88X3310, but there is a
difference: it does not support xaui host mode. Instead the
corresponding MACTYPE means
  rxaui / 5gbase-r / 2500base-x / sgmii without AN
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the only "changing" MACTYPE we support is when the PHY changes
between
  10gbase-r / 5gbase-r / 2500base-x / sgmii

Add support for
  usxgmii
  xaui / 5gbase-r / 2500base-x / sgmii
  rxaui / 5gbase-r / 2500base-x / sgmii
and also
  5gbase-r / 2500base-x / sgmii
for 88E2110.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have a chip structure, we can store the temperature reading
method in this structure (OOP style).
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 88E2110 does not support xaui nor rxaui modes. Check for correct
interface mode for different chips.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for all rate matching modes for 88X3310 (currently only
10gbase-r is supported, but xaui and rxaui can also be used).

Add support for rate matching for 88E2110 (on 88E2110 the MACTYPE
register is at a different place).

Currently rate matching mode is selected by strapping pins (by setting
the MACTYPE register). There is work in progress to enable this driver
to deduce the best MACTYPE from the knowledge of which interface modes
are supported by the host, but this work is not finished yet.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add all MACTYPE definitions for 88E2110, 88E2180, 88E2111 and 88E2181.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add all MACTYPE definitions for 88X3310, 88X3310P, 88X3340 and 88X3340P.

In order to have consistent naming, rename
MV_V2_33X0_PORT_CTRL_MACTYPE_RATE_MATCH to
MV_V2_33X0_PORT_CTRL_MACTYPE_10GBASER_RATE_MATCH.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>