- 19 Sep, 2023 4 commits
-
-
Charles Keepax authored
For very slow removals the current bias sense timeout is sometimes too short and unclamps the mic bias before the jack removal is properly detected by the tip detect, causing a pop. As bias sense should be tuned to deliver very few false positives, increase the timeout fairly dramatically to cover all but the most exaggerated removals. Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20230919103116.580305-6-ckeepax@opensource.cirrus.comSigned-off-by:
Mark Brown <broonie@kernel.org>
-
Charles Keepax authored
Currently the bias sense is enabled along with the button detect, but this has two problems. Firstly, the detections themselves arn't covered by the bias sense, potentially resulting in pops and secondly, the sequence of enabling/disabling looks like: enable bias enable bias sense disable bias sense disable bias When the bias sense is disabled but the bias is still on the clamp is removed and a pop results. Fix both of these issues by moving the bias sense enable/disable to be along with the bias itself. With a resulting sequence of: enable bias sense enable bias disable bias disable bias sense Signed-off-by:
-
Charles Keepax authored
Improve the default pop performance on jack removal by enabling bias sense on the least sensitive level by default. Signed-off-by:
-
Charles Keepax authored
The current default is a little excessive, reduce the pop on insertion by reducing the time a little. The new value of 1000uS is still pretty conservative. Signed-off-by:
-
- 18 Sep, 2023 6 commits
-
-
Mark Brown authored
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>: da7213 is still using M/S instead of P/C for SND_SOC_DAIFMT_CBx_CFx. [PATCH 1/2] will update it. [PATCH 2/2] will enable DAI format automatic select.
-
Kuninori Morimoto authored
By this patch, DAI format might be automatically selected (Depends on paired DAI, and/or Sound Card). Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: Linh Phung <linh.phung.jy@renesas.com> Tested-by:
Khanh Le <khanh.le.xr@renesas.com> Link: https://lore.kernel.org/r/87y1hdh4f1.wl-kuninori.morimoto.gx@renesas.comSigned-off-by:
-
Kuninori Morimoto authored
We should use P/C instead of M/S for SND_SOC_DAIFMT_CBx_CFx. We should use SND_SOC_DAIFMT_xxx instead of SND_SOC_DAI_FORMAT_xxx This patch tidyup these. Signed-off-by:
-
John Watts authored
The WM8782 can safely support rates higher than 48kHz by changing the value of the FSAMPEN pin. Allow specifying the FSAMPEN pin value in the device tree. Signed-off-by:
John Watts <contact@jookia.org> Acked-by:
-
John Watts authored
The wm8782 supports rates 96kHz and 192kHz as long as the hardware is configured properly. Allow this to be specified in the device tree. Signed-off-by:
-
John Watts authored
The wm8782 supports up to 192kHz audio when pins are set correctly. Instead of hardcoding which rates are supported constrain them at runtime based on a max_rate variable. Signed-off-by:
-
- 15 Sep, 2023 30 commits
-
-
Colin Ian King authored
Don't populate the const array controls on the stack, instead make it static. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Acked-by:
-
Arun T authored
Initial support for ARL w/ RT711 Signed-off-by:
Arun T <arun.t@intel.com> Reviewed-by:
Kai Vehmanen <kai.vehmanen@linux.intel.com> Reviewed-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by:
Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20230915080635.1619942-1-yung-chuan.liao@linux.intel.comSigned-off-by:
-
Mark Brown authored
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>: If the copier supports a single format on the DAI side we should fixup the BE dailink to use this single format.
-
Mark Brown authored
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>: Rather than keeping a single array of CPU dai link components allocate a smaller one for each DAI link, this reduces the amount of state that needs to be passed back and forth in the driver.
-
Mark Brown authored
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>: This series implements support for split library loading to comply with the HDA DMA programming sequence recommendation, which is: 1. DSP side DMA programming and GEN bit set to 1 2. host side DMA programming and RUN bit set to 1 The SOF support for library loading is based on this sequence, backwards compatibility with older reference firmware is supported (where only the LOAD_LIBRARY message is supported).
-
Mark Brown authored
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>: These 3 patches update the pm_ops for I2C/SPI so that they are only built and exported if they are needed.
-
Mark Brown authored
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>: Some cleanups from Brent Lu for I2S platforms. And minor additions for RVPs and Chromebooks.
-
Brent Lu authored
Use ssp-common module to detect codec and amplifier type in driver probe function and remove all quirks about amplifier type. Signed-off-by:
Brent Lu <brent.lu@intel.com> Reviewed-by:
-
Brent Lu authored
This configuration supports ADL boards which implement DA7219 on SSP0 and MAX98360A on SSP1. DA7219 uses PLL bypass mode to avoid WCLK locking problem. To use this mode, MCLK frequency must be 12.288 or 24.576MHz. Signed-off-by:
-
Brent Lu authored
Use maxim-common module to handle speaker amp DAI link registration. No functional change in this commit. Signed-off-by:
-
Brent Lu authored
Rename the driver file and kernel option to be consistent with other SOF machine drivers. Signed-off-by:
-
Brent Lu authored
Use realtek-common module to support rt1019p speaker amplifier. Signed-off-by:
-
Brent Lu authored
Use nuvoton-common module to support nau8318 speaker amplifier. Signed-off-by:
-
Brent Lu authored
Implement nau8318 support code in this common module so it could be shared between multiple SOF machine drivers. Signed-off-by:
-
Brent Lu authored
A BE DAI link for speaker amplifier is always created even a board quirk specifies there is no amplifier. Modify the driver to check amplifier type before creating corresponding DAI link. The topology (sof-tgl-rt1308-hdmi-ssp.m4) which supports HDMI-IN is using fixed BE ID for each DAI link. Therefore we also uses fixed ID in machine driver side. Signed-off-by:
Balamurugan C <balamurugan.c@intel.com> Signed-off-by:
-
Balamurugan C authored
Added HDMI-in capture support for RPL boards. previously it used adl machines and now its moved into separate match entry. Signed-off-by:
-
Brent Lu authored
This configuration supports ADL boards which implement ALC5650 dual I2S interface codec. Two DAI links are added: AIF1 (on codec side) for headphone and AIF2 for speakers. Signed-off-by:
-
Uday M Bhat authored
For all MTL/Rex devices, number of HDMI supported is 3. Signed-off-by:
Yong Zhi <yong.zhi@intel.com> Signed-off-by:
Uday M Bhat <uday.m.bhat@intel.com> Reviewed-by:
-
Uday M Bhat authored
System firmware has included additional audio DMI string MAX98360_ALC5682I_DISCRETE_I2S_BT for discrete BT offload supporting devices. Same DMI string match is introduced in sof_rt5682_quirk_table. Signed-off-by:
-
Brent Lu authored
Use ssp-common module to detect codec and amplifier type in driver probe function and remove all quirks about codec and amplifier type. Signed-off-by:
Rander Wang <rander.wang@intel.com> Reviewed-by:
-
Brent Lu authored
Use ssp-common module to detect codec and amplifier type in driver probe function and remove all quirks about codec and amplifier type. Signed-off-by:
-
Brent Lu authored
Use ssp-common module to detect codec and amplifier type in driver probe function and remove all quirks about codec and amplifier type. Signed-off-by:
-
Brent Lu authored
Use ssp-common module to detect codec and amplifier type in driver probe function and remove all quirks about codec and amplifier type. Due to codec detection feature, we could remove HP Dooly's DMI quirk safely. Signed-off-by:
-
Brent Lu authored
Use ACPI HID definition in ssp-common header for device name macros. No functional change here. Signed-off-by:
-
Brent Lu authored
Create a new common module to host functions which could be shared among SSP machine drivers. Add functions to detect headphone codec and speaker amplifier via ACPI system at runtime in order to remove codec type quirks in machine drivers. Signed-off-by:
-
Brent Lu authored
Remove SOF_RT5682_MCLK_24MHZ flag from JSL and CML/WHL board configs since the information could be retrieved from SOF API. The macro itself is removed as well. Signed-off-by:
-
Charles Keepax authored
Rather than incrementing the ID for the dai_links in many places throughout the code, just increment it each time we initialise a new DAI link. Signed-off-by:
-
Charles Keepax authored
Now only the SoundWire part of the code uses the global cpus array, remove it and have create_sdw_dailink allocate its own link components. This removes a lot of state being passed around in the driver, which simplifies things a fair bit. Signed-off-by:
-
Charles Keepax authored
The code contains a fair amount of state tracking and one part of that is keeping track of which entry in the large global cpus snd_soc_dai_link_component array is currently in use. Add a helper function to allocate a simple DAI link, this simplifies the code slightly and moves us in the direction of eliminating the need for the large global cpus array. This does slightly increase the number of allocations done, but this is probe time and the code already does a large number of allocations so this increase is small over all. Signed-off-by:
-
Charles Keepax authored
Whilst it should not cause any issues as only a single instance of the machine will be instantiated, it is still slightly better practice to keep working data in the private data structure, rather than a global variable. Move sdw_pin_index into the mc_private structure. Signed-off-by:
-
