UMR MTTs used in striding RQ have certain alignment requirements. While
it's guaranteed to work when UMR pages are aligned to the UMR page size,
in practice it works then UMR pages are aligned to 8 bytes. However,
it's still not enough flexibility for the unaligned mode of XSK. This
patch leverages KSM to map UMR pages without alignment requirements,
when unaligned XSK is active. The downside is that KSM entries are twice
as big as MTTs, which limits the maximum WQE size, so regular RQs and
aligned XSK continue using MTTs.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some commands use a flexible array after a common header. Add a macro to
safely calculate the total input length of the command, detecting
overflows and printing errors with specific values when such overflows
happen.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, rq->mkey_be keeps a big-endian value of either the PA MKey
(for legacy RQ, no address translation) or MTT MKey (for striding RQ,
direct address translation). Striding RQ stores the same value in
rq->umr_mkey in the native endianness.

The next commit will make striding RQ use KSM MKey (indirect address
translation) for the unaligned mode of XSK, which will require storing
both KSM MKey and PA MKey in the RQ struct. This commit optimizes fields
of mlx5e_rq: umr_mkey is removed (it's redundant), mkey_be always points
to the PA MKey, and mpwqe.umr_mkey_be points to the MTT MKey (or to the
KSM MKey, starting from the next commit).
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

XSK RQs support striding RQ linear mode, but the stride size is always
set to PAGE_SIZE. It may be larger than the XSK frame size,
unnecessarily reducing the useful space in a WQE, but more importantly
causing UMEM data corruption in certain cases.

Normally, stride size bigger than XSK frame size is not a problem if the
hardware enforces the MTU. However, traffic between vports skips the
hardware MTU check, and oversized packets may be received.

If an oversized packet is bigger than the XSK frame but not bigger than
the stride, it will cause overwriting of the adjacent UMEM region. If
the packet takes more than one stride, they can be recycled for reuse
so it's not a problem when the XSK frame size matches the stride size.

To reduce the impact of the above issue, attempt to use the MTT page
size for striding RQ that matches the XSK frame size, allowing to safely
use 2048-byte frames on an up-to-date firmware.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This commit allows striding RQ to determine MTT page size at runtime,
instead of sticking to the compile-time PAGE_SIZE. This functionality
will be used by a following commit that adjusts the MTT page size to the
XSK frame size.

Stick with PAGE_SIZE for XSK on legacy RQ, as frag_stride is not used in
data path, it only helps calculate how pages are partitioned into
fragments, and PAGE_SIZE will ensure each fragment starts at the
beginning of a new allocation unit (XSK frame).
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Drivers should be aware of the range of valid UMEM chunk sizes to be
able to allocate their internal structures of an appropriate size. It
will be used by mlx5e in the following patches.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
CC: "Björn Töpel" <bjorn@kernel.org>
CC: Magnus Karlsson <magnus.karlsson@intel.com>
CC: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There should be no space before the comma
Signed-off-by: Hongbin Wang <wh_bin@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jianguo Zhang says:

====================
Mediatek ethernet patches for mt8188

Changes in v7:

v7:
1) Add 'Reviewed-by: AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com>' info in commit message of
patch 'dt-bindings: net: snps,dwmac: add new property snps,clk-csr',
'arm64: dts: mediatek: mt2712e: Update the name of property 'clk_csr''
and 'net: stmmac: add a parse for new property 'snps,clk-csr''.

v6:
1) Update commit message of patch 'dt-bindings: net: snps,dwmac: add new property snps,clk-csr'
2) Add a parse for new property 'snps,clk-csr' in patch
'net: stmmac: add a parse for new property 'snps,clk-csr''

v5:
1) Rename the property 'clk_csr' as 'snps,clk-csr' in binding
file as Krzysztof Kozlowski'comment.
2) Add DTS patch 'arm64: dts: mediatek: mt2712e: Update the name of property 'clk_csr''
as Krzysztof Kozlowski'comment.
3) Add driver patch 'net: stmmac: Update the name of property 'clk_csr''
as Krzysztof Kozlowski'comment.

v4:
1) Update the commit message of patch 'dt-bindings: net: snps,dwmac: add clk_csr property'
as Krzysztof Kozlowski'comment.

v3:
1) List the names of SoCs mt8188 and mt8195 in correct order as
AngeloGioacchino Del Regno's comment.
2) Add patch version info as Krzysztof Kozlowski'comment.

v2:
1) Delete patch 'stmmac: dwmac-mediatek: add support for mt8188' as
Krzysztof Kozlowski's comment.
2) Update patch 'dt-bindings: net: mediatek-dwmac: add support for
mt8188' as Krzysztof Kozlowski's comment.
3) Add clk_csr property to fix warning ('clk_csr' was unexpected) when
runnig 'make dtbs_check'.

v1:
1) Add ethernet driver entry for mt8188.
2) Add binding document for ethernet on mt8188.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Parse new property 'snps,clk-csr' firstly because the new property
is documented in binding file, if failed, fall back to old property
'clk_csr' for legacy case
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the name of property 'clk_csr' as 'snps,clk-csr' to align with
the property name in the binding file.
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add description for new property snps,clk-csr in binding file
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add binding document for the ethernet on mt8188
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a devlink_health_report message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a literal string in the array
bnad_net_stats_strings. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement channel management functions to allow dynamic addition and
removal of transmit queues. The `ethtool --show-channels` and
`ethtool --set-channels` commands can be used to get and set the
number of queues, respectively. Allow the ability to add as many
transmit queues as available processors but never allow more than the
hard maximum of 16. The number of receive queues is one and cannot be
modified.

Depending on whether the requested number of queues is larger or
smaller than the current value, either allocate or free long term
buffers. Since long term buffer construction and destruction can
occur in two different areas, from either channel set requests or
device open/close, define functions for performing this work. If
allocation of a new buffer fails, then attempt to revert back to the
previous number of queues.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The `ndo_start_xmit` function is protected by a spinlock on the tx queue
being used to transmit the skb. Allow concurrent calls to
`ndo_start_xmit` by using more than one tx queue. This allows for
greater throughput when several jobs are trying to transmit data.

Introduce 16 tx queues (leave single rx queue as is) which each
correspond to one DMA mapped long term buffer.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than DMA mapping and unmapping every outgoing skb, copy the skb
into a buffer that was mapped during the drivers open function. Copying
the skb and its frags have proven to be more time efficient than
mapping and unmapping. As an effect, performance increases by 3-5
Gbits/s.

Allocate and DMA map one continuous 64KB buffer at `ndo_open`. This
buffer is maintained until `ibmveth_close` is called. This buffer is
large enough to hold the largest possible linnear skb. During
`ndo_start_xmit`, copy the skb and all of it's frags into the continuous
buffer. By manually linnearizing all the socket buffers, time is saved
during memcpy as well as more efficient handling in FW.
As a result, we no longer need to worry about the firmware limitation
of handling a max of 6 frags. So, we only need to maintain 1 descriptor
instead of 6 and can hardcode 0 for the other 5 descriptors during
h_send_logical_lan.

Since, DMA allocation/mapping issues can no longer arise in xmit
functions, we can further reduce code size by removing the need for a
bounce buffer on DMA errors.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are spelling mistakes in two literal strings. Fix these.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As 2.5G, 5G ethernet ports are more common and affordable,
these ports are being used in LAN bridge devices.
STP port_cost() is missing path_cost assignment for these link speeds,
causes highest cost 100 being used.
This result in lower speed port being picked
when there is loop between 5G and 1G ports.

Original path_cost: 10G=2, 1G=4, 100m=19, 10m=100
Adjusted path_cost: 10G=2, 5G=3, 2.5G=4, 1G=5, 100m=19, 10m=100
                    speed greater than 10G = 1
Signed-off-by: Steven Hsieh <steven.hsieh@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a netdev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pskb_may_pull already contains all of the checks performed by
pskb_pull.
Use pskb_may_pull for validation in pskb_pull, eliminating the
duplication and making __pskb_pull obsolete.
Replace __pskb_pull with pskb_pull where applicable.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the value
to be returned to user space.
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the value
to be returned to user space.
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the value
to be returned to user space.
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gerhard Engleder says:

====================
tsnep: multi queue support and some other improvements

Add support for additional TX/RX queues along with RX flow classification
support.

Binding is extended to allow additional interrupts for additional TX/RX
queues. Also dma-coherent is allowed as minor improvement.

RX path optimisation is done by using page pool as preparations for future
XDP support.

v4:
- rework dma-coherent commit message (Krzysztof Kozlowski)
- fixed order of interrupt-names in binding (Krzysztof Kozlowski)
- add line break between examples in binding (Krzysztof Kozlowski)
- add RX_CLS_LOC_ANY support to RX flow classification

v3:
- now with changes in cover letter

v2:
- use netdev_name() (Jakub Kicinski)
- use ENOENT if RX flow rule is not found (Jakub Kicinski)
- eliminate return code of tsnep_add_rule() (Jakub Kicinski)
- remove commit with lazy refill due to depletion problem (Jakub Kicinski)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use page pool for RX buffer handling. Makes RX path more efficient and
is required prework for future XDP support.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Received Ethernet frames are assigned to first RX queue per default.
Based on EtherType Ethernet frames can be assigned to other RX queues.
This enables processing of real-time Ethernet protocols on dedicated
RX queues.

Add RX flow classification interface for EtherType based RX queue
assignment.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support additional TX/RX queue pairs if dedicated interrupt is
available. Interrupts are detected by name in device tree.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For multiple queues multiple interrupts shall be used. Therefore, rework
global interrupt to per queue interrupt.

Every interrupt name shall contain interface name and queue information.
To get a valid interface name, the interrupt request needs to by done
during open like in other drivers. Additionally, this allows the removal
of some initialisation checks in the interrupt handler.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Additional TX/RX queue pairs require dedicated interrupts. Extend
binding with additional interrupts.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Within SoCs like ZynqMP, FPGA logic can be connected to different kinds
of AXI master ports. Also cache coherent AXI master ports are available.
The property "dma-coherent" is used to signal that DMA is cache
coherent.

Add "dma-coherent" property to allow the configuration of cache coherent
DMA.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-09-28 (ice)

Arkadiusz implements a single pin initialization function, checking feature
bits, instead of having separate device functions and updates sub-device
IDs for recognizing E810T devices.

Martyna adds support for switchdev filters on VLAN priority field.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ice: Add support for VLAN priority filters in switchdev
  ice: support features on new E810T variants
  ice: Merge pin initialization of E810 and E810T adapters
====================

Link: https://lore.kernel.org/r/20220928203217.411078-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the value
to be returned to user space.
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1664364860-29153-1-git-send-email-wangyufen@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
Add tc-taprio support for queueMaxSDU

The tc-taprio offload mode supported by the Felix DSA driver has
limitations surrounding its guard bands.

The initial discussion was at:
https://lore.kernel.org/netdev/c7618025da6723418c56a54fe4683bd7@walle.cc/

with the latest status being that we now have a vsc9959_tas_guard_bands_update()
method which makes a best-guess attempt at how much useful space to
reserve for packet scheduling in a taprio interval, and how much to
reserve for guard bands.

IEEE 802.1Q actually does offer a tunable variable (queueMaxSDU) which
can determine the max MTU supported per traffic class. In turn we can
determine the size we need for the guard bands, depending on the
queueMaxSDU. This way we can make the guard band of small taprio
intervals smaller than one full MTU worth of transmission time, if we
know that said traffic class will transport only smaller packets.

As discussed with Gerhard Engleder, the queueMaxSDU may also be useful
in limiting the latency on an endpoint, if some of the TX queues are
outside of the control of the Linux driver.
https://patchwork.kernel.org/project/netdevbpf/patch/20220914153303.1792444-11-vladimir.oltean@nxp.com/

Allow input of queueMaxSDU through netlink into tc-taprio, offload it to
the hardware I have access to (LS1028A), and (implicitly) deny
non-default values to everyone else. Kurt Kanzenbach has also kindly
tested and shared a patch to offload this to hellcreek.

v3 at:
https://patchwork.kernel.org/project/netdevbpf/cover/20220927234746.1823648-1-vladimir.oltean@nxp.com/
v2 at:
https://patchwork.kernel.org/project/netdevbpf/list/?series=679954&state=*
v1 at:
https://patchwork.kernel.org/project/netdevbpf/cover/20220914153303.1792444-1-vladimir.oltean@nxp.com/
====================

Link: https://lore.kernel.org/r/20220928095204.2093716-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The driver currently sets the PTCMSDUR register statically to the max
MTU supported by the interface. Keep this logic if tc-taprio is absent
or if the max_sdu for a traffic class is 0, and follow the requested max
SDU size otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The Port Time Gating Control Register (PTGCR) and Port Time Gating
Capability Register (PTGCAPR) have definitions in the driver which
aren't in line with the other registers. Rename these.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The &priv->si->hw construct dereferences 2 pointers and makes lines
longer than they need to be, in turn making the code harder to read.

Replace &priv->si->hw accesses with a "hw" variable when there are 2 or
more accesses within a function that dereference this. This includes
loops, since &priv->si->hw is a loop invariant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for configuring the max SDU per priority and per port. If not
specified, keep the default.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The following patch will need to make this function also respond to
TC_QUERY_BASE, so make the processing more structured around the
tc_setup_type.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Our current vsc9959_tas_guard_bands_update() algorithm has a limitation
imposed by the hardware design. To avoid packet overruns between one
gate interval and the next (which would add jitter for scheduled traffic
in the next gate), we configure the switch to use guard bands. These are
as large as the largest packet which is possible to be transmitted.

The problem is that at tc-taprio intervals of sizes comparable to a
guard band, there isn't an obvious place in which to split the interval
between the useful portion (for scheduling) and the guard band portion
(where scheduling is blocked).

For example, a 10 us interval at 1Gbps allows 1225 octets to be
transmitted. We currently split the interval between the bare minimum of
33 ns useful time (required to schedule a single packet) and the rest as
guard band.

But 33 ns of useful scheduling time will only allow a single packet to
be sent, be that packet 1200 octets in size, or 60 octets in size. It is
impossible to send 2 60 octets frames in the 10 us window. Except that
if we reduced the guard band (and therefore the maximum allowable SDU
size) to 5 us, the useful time for scheduling is now also 5 us, so more
packets could be scheduled.

The hardware inflexibility of not scheduling according to individual
packet lengths must unfortunately propagate to the user, who needs to
tune the queueMaxSDU values if he wants to fit more small packets into a
10 us interval, rather than one large packet.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>