I2C is only required when using the config item BATTERY_BQ27XXX_I2C which
already depends on the I2C subsystem, remove the unneeded dependency from
BATTERY_BQ27XXX.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The IRQ handler is not used by the platform based
code resulting in a 'defined but not used' warning,
if CONFIG_BQ27XXX_I2C is not enabled.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>

Add missing initialization of register mapping table to
platform probe function.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>

This driver fails to link without CONFIG_IIO, since
there are no stubs for the iio_channels functions.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Marek Belisko <marek@goldelico.com>
Acked-by: Nikolaus Schaller <hns@goldelico.com>

for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):

// <smpl>
@@
expression root,e;
local idexpression child;
@@

 for_each_child_of_node(root, child) {
   ... when != of_node_put(child)
       when != e = child
(
   return child;
|
+  of_node_put(child);
?  return ...;
)
   ...
 }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Document the settings exported by bq24257 charger driver through sysfs
entries:
- ovp_voltage
- in_dpm_voltage
- high_impedance_enable
- sysoff_enable
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This patch adds support for enabling/disabling optional device specific
features through sysfs properties at runtime.

* High-impedance mode enable/disable
* Sysoff enable/disable

Refer to the respective device datasheets for more information:

http://www.ti.com/product/bq24250
http://www.ti.com/product/bq24251
http://www.ti.com/product/bq24257Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This patch allows reading and writing of the input current limit through
the power supply's input_current_limit sysfs property. This allows
userspace to see what charger was detected (if the D+/D- USB signal-
based charger type detection is enabled) and to re-configure the maximum
current drawn from the external supply at runtime based on system-level
knowledge or user input. Note that upon charger disconnection and
re-connection the limit configured through firmware becomes active again
(or the D+/D- USB signal-based charger detection will be run again).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

A new optional device property called "ti,in-dpm-voltage" is introduced
to allow configuring the input voltage threshold for the devices'
dynamic power path management (DPM) feature. In short, it can be used to
prevent the input voltage from dropping below a certain value as current
is drawn to charge the battery or supply the system.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

A new optional device property called "ti,ovp-voltage" is introduced to
allow configuring the input over voltage protection setting.

This commit also adds the basic sysfs support for custom properties
which is being used to allow userspace to read the current ovp-voltage
setting.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

A software-based approach for determining the charger's input voltage
"Power Good" state is introduced for devices like the bq24250 which
don't have a dedicated hardware pin for that purpose. This SW-based
approach is also used for other devices (with dedicated PG pin) as a
fall back solution if that pin is not configured to be used through
"pg-gpios".
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

A new optional device property called "ti,current-limit" is introduced
to allow disabling the D+/D- USB signal-based charger type auto-
detection algorithm used to set the input current limit and instead to
use a fixed input current limit.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Adding a missing bit definition for the sake of consistency device model
vs. bit field representation. No change in functionality.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This patch adds basic support for bq24250 and bq24251 which are very
similar to the bq24257 the driver was originally written for. Basic
support means the ability to select a device through Kconfig, DT and
ACPI, an instance variable allowing to check which chip is active, and
the reporting back of the selected device through the model_name power
supply sysfs property.

This patch by itself is not sufficient to actually use those two added
devices in a real-world setting due to some feature differences which
are addressed by other patches in this series.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Extend the bq24257 charger's device tree documentation to cover the
bq24250 and bq24251 devices as well feature additions.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Eliminate a few lines of code by using the PTR_ERR_OR_ZERO() macro.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Use the devm_* managed version of the function to register the power
supply and remove the associated unregister function. This will simplify
error handling moving forward as it allows the unregister to happen
automatically. It also saves a few lines of code.

As this changes the order of putting the bq24257 into reset vs.
unregistering the power-supply during driver remove re-tested various
driver unload scenario to make sure that this doesn't cause any
unintended side effects such as erroneous interrupts.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The maximum amount of input current the charger should draw is dependent
on the power supply and should only be (re-)configured when the power
supply gets connected and disconnected. However the driver was also
lowering the bq24257's input current limit setting to 500mA when the
battery was removed and restored the previous setting according to the
power supply capabilities when the battery was reconnected although
these events are not impacting the amount of power that can be drawn
from the supply. Furthermore, a re-configuration of the input current
limit to 500mA when the battery gets disconnected is actually dangerous
if the limit was set higher previously and the system draws more than
500mA in which case the system voltage would be reduced in order to
maintain 500mA which could result in the system getting too low of a
supply to maintain operation. Last but not least the mechanism itself
used for battery re-connection detection did not work in corner cases
such as when the device's input current loop becomes active and the
bq24257 device clears its battery fault error resulting in incorrectly
reporting that the battery got reconnected.

This patches removes the impact the battery removal/insertion has on the
input current limit configured for the bq24257 and simplifies the
associated handler routine.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

At the time the driver was written GpioInt resources in ACPI were not
passed to the driver in client->irq, as opposed to DT enumeration. To
accommodate this use case, a "stat-gpios" property was introduced to
allow configuring the IRQ.

However this issue with ACPI was fixed in commit "845c8770 i2c / ACPI:
Assign IRQ for devices that have GpioInt automatically" and makes this
workaround no longer necessary, hence we can remove the support for the
"stat-gpios" property and the associated code from the bq24257 driver.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

We need flags to be signed for the error handling to work.

The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576

Fixes: 74aab849 ('power: bq27xxx_battery: Cleanup health checking')
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

If either twl4030_charger or twl4030_madc is configured as MODULE,
we get build (link) errors.

To solve, the direct call of twl4030_get_madc_conversion() is replaced
by a call to iio_read_channel_processed().
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Added new iio properties which are required for twl4030-charger driver and
allow to use twl4030-madc indirectly.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.

scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.

Fixes: b5874f33 ("wm831x_power: Use genirq")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This patch adds support for the tps65217 charger driver. This driver is
responsible for controlling the charger aspect of the tps65217 mfd.
Currently, this mainly consists of turning on and off the charger, but
some other features of the charger can be supported through this driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The TPS65217 charger is a subnode of the TPS65217 MFD.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

"state" is a bool so it's never less than zero.  The intent was to test
"ret" instead.

Fixes: 56d7df87 ('power: Add Qualcomm SMBB driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Commit b68c3161 (bq2415x_charger: Allow to load and use driver even if
notify device is not registered yet) introduced null pointer dereference in
case bq is NULL. This patch fixes it.

Fixes: b68c3161 ("bq2415x_charger: Allow to load and use driver even if notify device is not registered yet")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Some devices have a pin that can generate an interrupt when
the battery's status changes. Add an interrupt handler to
read the new battery status.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Reorganize the logic checking battery health and add under temperature
condition checking.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Add support for additional devices and register equivalent family devices
including the bq27010, bq27210, bq27500, bq27510, bq27520, bq27530,
bq27531, bq27541, bq27542, bq27546, bq27545, bq27441, bq27421, and the
bq27641.

To facilitate this process the register mapings have been moved to tables
and other small cleanups have been made.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Fix typos and change "relative state of charge" to "state of charge" as not
all supported devices use relative state of charge.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

When initialized as a platform device the initializer must now specify
a device. An empty device name is no longer valid.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The MODULE_DEVICE_TABLE macro automatically adds all needed
i2c MODULE_ALIASes so remove the extra MODULE_ALIAS.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Use managed resource function devm_power_supply_register instead
of power_supply_register to simplify the error path by allowing
unregister to happen automatically on error. To be compatible with
the change, replace various gotos by direct returns and remove
unneeded label err.

Also, remove max8998_battery_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

By accident I stumbled over a few misspelled words in the
charger-manager header file which this patch fixes. Namely:
- Extcon rather than Exton
- constraint rather than constratint
- existence rather than existance
- difference rather than diffential

While at it also add a missing space before a closing comment star
forward-slash.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Use managed resource functions devm_request_threaded_irq and
devm_power_supply_register to simplify error handling.

To be compatible with the change, various gotos are replaced
with direct returns and unneeded labels are dropped. Also,
remove max8903_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Use managed resource functions devm_request_threaded_irq and
devm_power_supply_register to simplify error handling.

Also, remove max17042_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This diver doesn't applies only on SAM9 SoC families but on SAMA5 families
as well.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>