Skip to content

L
linux
Switch branch/tag
  1. 09 Nov, 2010 1 commit
    • Anand Gadiyar's avatar
      usb: musb: fail unaligned DMA transfers on v1.8 and above · 6e16edfe
      Anand Gadiyar authored 
      The Inventra DMA engine in version 1.8 and later of the MUSB
controller cannot handle DMA addresses that are not aligned
to a 4 byte boundary. It ends up ignoring the last two bits
programmed in the DMA_ADDR register. This is a deliberate
design change in the controller and is documented in the
programming guide.

Earlier versions of the controller could handle these
accesses just fine.

Fail dma_channel_program if we see an unaligned address when
using the newer controllers, so that the caller can carry out
the transfer using PIO mode.
(Current callers already have this backup path in place).
Signed-off-by: default avatarAnand Gadiyar <gadiyar@ti.com>
Tested-by: default avatarMing Lei <tom.leiming@gmail.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      6e16edfe
  3. 08 Nov, 2010 1 commit
  5. 05 Nov, 2010 11 commits
    • Heikki Krogerus's avatar
      usb: musb: Fix handling of spurious SESSREQ · 19aab56c
      Heikki Krogerus authored 
      Rely on VBUS being valid on top off B device.
Signed-off-by: default avatarHeikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      19aab56c
    • Ming Lei's avatar
      usb: musb: fix kernel oops when loading musb_hdrc module for the 2nd time · b2120914
      Ming Lei authored 
      musb driver still may write MUSB_DEVCTL register after clock is disabled
in musb_platform_exit, which may cause the kernel oops[1] when musb_hdrc
module is loaded for the 2nd time.

The patch fixes the kernel oops in this case.

[1] kernel oops when loading musb_hdrc module for the 2nd time

[   93.380279] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=5
[   93.387847] bus: 'platform': add driver musb_hdrc
[   93.388153] bus: 'platform': driver_probe_device: matched device musb_hdrc with driver musb_hdrc
[   93.388183] bus: 'platform': really_probe: probing driver musb_hdrc with device musb_hdrc
[   93.405090] HS USB OTG: revision 0x33, sysconfig 0x2010, sysstatus 0x1, intrfsel 0x1, simenable  0x0
[   93.405364] musb_hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[   93.405395] musb_hdrc: MHDRC RTL version 1.400
[   93.405426] musb_hdrc: setup fifo_mode 3
[   93.405456] musb_hdrc: 7/31 max ep, 3648/16384 memory
[   93.405487] musb_core_init 1524: musb_hdrc: hw_ep 0shared, max 64
[   93.405487] musb_core_init 1524: musb_hdrc: hw_ep 1tx, doublebuffer, max 512
[   93.405517] musb_core_init 1533: musb_hdrc: hw_ep 1rx, doublebuffer, max 512
[   93.405548] musb_core_init 1524: musb_hdrc: hw_ep 2tx, max 512
[   93.405578] musb_core_init 1533: musb_hdrc: hw_ep 2rx, max 512
[   93.405578] musb_core_init 1524: musb_hdrc: hw_ep 3shared, max 256
[   93.405609] musb_core_init 1524: musb_hdrc: hw_ep 4shared, max 256
[   93.405853] musb_platform_try_idle 133: b_idle inactive, for idle timer for 7 ms
[   93.405944] device: 'gadget': device_add
[   93.406921] PM: Adding info for No Bus:gadget
[   93.406951] musb_init_controller 2136: OTG mode, status 0, dev80
[   93.407379] musb_do_idle 51: musb_do_idle: state=1
[   93.408233] musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[   93.416656] driver: 'musb_hdrc': driver_bound: bound to device 'musb_hdrc'
[   93.416687] bus: 'platform': really_probe: bound device musb_hdrc to driver musb_hdrc
[  124.486938] bus: 'platform': remove driver musb_hdrc
[  124.490509] twl4030_usb twl4030_usb: twl4030_phy_suspend
[  124.491424] device: 'gadget': device_unregister
[  124.491424] PM: Removing info for No Bus:gadget
[  124.495269]  gadget: musb_gadget_release
[  124.498992] driver: 'musb_hdrc': driver_release
[  129.569366] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=5
[  129.576934] bus: 'platform': add driver musb_hdrc
[  129.577209] bus: 'platform': driver_probe_device: matched device musb_hdrc with driver musb_hdrc
[  129.577239] bus: 'platform': really_probe: probing driver musb_hdrc with device musb_hdrc
[  129.592651] twl4030_usb twl4030_usb: twl4030_phy_resume
[  129.592681] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab404
[  129.600830] Internal error: : 1028 [#1]
[  129.604858] last sysfs file: /sys/devices/platform/i2c_omap.3/i2c-3/i2c-dev/i2c-3/dev
[  129.613067] Modules linked in: musb_hdrc(+) [last unloaded: musb_hdrc]
[  129.619964] CPU: 0    Not tainted  (2.6.36-next-20101021+ #372)
[  129.626281] PC is at musb_platform_init+0xb0/0x1c8 [musb_hdrc]
[  129.632415] LR is at mark_held_locks+0x64/0x94
[  129.637084] pc : [<bf032198>]    lr : [<c00ad7c4>]    psr: 20000013
[  129.637084] sp : c6d5fcb0  ip : c6d5fc38  fp : c6d5fcd4
[  129.649139] r10: c6e72180  r9 : fa0ab000  r8 : c05612e8
[  129.654602] r7 : 0000005c  r6 : c0559cc8  r5 : c6e72180  r4 : c0561548
[  129.661468] r3 : 04d60047  r2 : fa0ab000  r1 : c07169d8  r0 : 00000000
[  129.668304] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
[  129.675811] Control: 10c5387d  Table: 86e4c019  DAC: 00000015
[  129.681823] Process insmod (pid: 554, stack limit = 0xc6d5e2f0)
[  129.688049] Stack: (0xc6d5fcb0 to 0xc6d60000)
[  129.692626] fca0:                                     fa0ab000 c0555c54 c6d5fcd4 c0561548
[  129.701202] fcc0: 00000003 c05612e0 c6d5fe04 c6d5fcd8 bf03140c bf0320f4 c6d5fd9c c6d5fce8
[  129.709808] fce0: c015cb94 c041448c c06d9d10 ffffffff c6d5fd14 c6d5fd00 c00adbec c6d5fd40
[  129.718383] fd00: c015d478 c6d5fdb0 c6d5fd24 c00a9d18 c6d5e000 60000013 bf02a4ac c05612bc
[  129.726989] fd20: c0414fb4 c00a9cf0 c6d5fd54 c6d5fd38 c015bbdc c0244280 c6e8b7b0 c7929330
[  129.735565] fd40: c6d5fdb0 c6d5fdb0 c6d5fd7c c6e7227c c015c010 c015bb90 c015c2ac c6d5fdb0
[  129.744171] fd60: c7929330 c6d5fdb0 c7929330 c6e8b7b0 c6d5fd9c 00000000 c7929330 c6e8b7b0
[  129.752746] fd80: c6d5fdb0 00000000 00000001 00000000 c6d5fde4 c6d5fda0 c015d478 c015cb74
[  129.761322] fda0: c056138c 00000000 c6d5fdcc c6d5fdb8 c7929330 00000000 c056138c c05612e8
[  129.769927] fdc0: 00000000 c05612f0 c0c5d62c c06f6e00 c73217c0 00000000 c6d5fdf4 c05612e8
[  129.778503] fde0: c05612e8 bf02a2e4 c0c5d62c c06f6e00 c73217c0 00000000 c6d5fe14 c6d5fe08
[  129.787109] fe00: c029a398 bf0311c8 c6d5fe4c c6d5fe18 c0299120 c029a384 c7919140 22222222
[  129.795684] fe20: c6d5fe4c c05612e8 c056131c bf02a2e4 c0299278 c06f6e00 c73217c0 00000000
[  129.804290] fe40: c6d5fe6c c6d5fe50 c0299314 c0299020 00000000 c6d5fe70 bf02a2e4 c0299278
[  129.812866] fe60: c6d5fe94 c6d5fe70 c02987d4 c0299284 c7825060 c78c6618 00000000 bf02a2e4
[  129.821441] fe80: c06e4c98 00000000 c6d5fea4 c6d5fe98 c0298ea4 c0298778 c6d5fedc c6d5fea8
[  129.830047] fea0: c0297f84 c0298e8c bf02716c 000b9008 bf02a2e4 bf02a2d0 000b9008 bf02a2e4
[  129.838623] fec0: 00000000 c06f6e00 bf031000 00000000 c6d5fefc c6d5fee0 c0299614 c0297ec0
[  129.847229] fee0: bf02a2d0 000b9008 bf02a388 00000000 c6d5ff0c c6d5ff00 c029a868 c02995a8
[  129.855804] ff00: c6d5ff24 c6d5ff10 c029a88c c029a818 0010281c 000b9008 c6d5ff34 c6d5ff28
[  129.864410] ff20: bf03104c c029a878 c6d5ff7c c6d5ff38 c00463dc bf03100c 00000000 00000000
[  129.872985] ff40: 00000000 0010281c 000b9008 bf02a388 00000000 0010281c 000b9008 bf02a388
[  129.881591] ff60: 00000000 c00521c8 c6d5e000 00000000 c6d5ffa4 c6d5ff80 c00bb9b8 c00463ac
[  129.890167] ff80: c00adc88 c00ada68 00097e8e bebbfcf4 0010281c 00000080 00000000 c6d5ffa8
[  129.898742] ffa0: c0052000 c00bb908 00097e8e bebbfcf4 402c9008 0010281c 000b9008 bebbfe5a
[  129.907348] ffc0: 00097e8e bebbfcf4 0010281c 00000080 00000014 bebbfcf4 bebbfe06 0000005b
[  129.915924] ffe0: bebbf9a0 bebbf990 0001a108 40263ec0 60000010 402c9008 011b0000 0000007c
[  129.924499] Backtrace:
[  129.927185] [<bf0320e8>] (musb_platform_init+0x0/0x1c8 [musb_hdrc]) from [<bf03140c>] (musb_probe+0x250/0xf2c [musb_hdrc])
[  129.938781]  r6:c05612e0 r5:00000003 r4:c0561548
[  129.943695] [<bf0311bc>] (musb_probe+0x0/0xf2c [musb_hdrc]) from [<c029a398>] (platform_drv_probe+0x20/0x24)
[  129.954040] [<c029a378>] (platform_drv_probe+0x0/0x24) from [<c0299120>] (driver_probe_device+0x10c/0x264)
[  129.964172] [<c0299014>] (driver_probe_device+0x0/0x264) from [<c0299314>] (__driver_attach+0x9c/0xa0)
[  129.973968] [<c0299278>] (__driver_attach+0x0/0xa0) from [<c02987d4>] (bus_for_each_dev+0x68/0x94)
[  129.983367]  r7:c0299278 r6:bf02a2e4 r5:c6d5fe70 r4:00000000
[  129.989349] [<c029876c>] (bus_for_each_dev+0x0/0x94) from [<c0298ea4>] (driver_attach+0x24/0x28)
[  129.998565]  r7:00000000 r6:c06e4c98 r5:bf02a2e4 r4:00000000
[  130.004547] [<c0298e80>] (driver_attach+0x0/0x28) from [<c0297f84>] (bus_add_driver+0xd0/0x274)
[  130.013671] [<c0297eb4>] (bus_add_driver+0x0/0x274) from [<c0299614>] (driver_register+0x78/0x158)
[  130.023101] [<c029959c>] (driver_register+0x0/0x158) from [<c029a868>] (platform_driver_register+0x5c/0x60)
[  130.033325]  r7:00000000 r6:bf02a388 r5:000b9008 r4:bf02a2d0
[  130.039276] [<c029a80c>] (platform_driver_register+0x0/0x60) from [<c029a88c>] (platform_driver_probe+0x20/0xa8)
[  130.050018] [<c029a86c>] (platform_driver_probe+0x0/0xa8) from [<bf03104c>] (musb_init+0x4c/0x54 [musb_hdrc])
[  130.060424]  r5:000b9008 r4:0010281c
[  130.064239] [<bf031000>] (musb_init+0x0/0x54 [musb_hdrc]) from [<c00463dc>] (do_one_initcall+0x3c/0x1c0)
[  130.074218] [<c00463a0>] (do_one_initcall+0x0/0x1c0) from [<c00bb9b8>] (sys_init_module+0xbc/0x1d0)
[  130.083709] [<c00bb8fc>] (sys_init_module+0x0/0x1d0) from [<c0052000>] (ret_fast_syscall+0x0/0x3c)
[  130.093109]  r7:00000080 r6:0010281c r5:bebbfcf4 r4:00097e8e
[  130.099090] Code: 0a000046 e3a01001 e12fff33 e59520e4 (e5923404)
[  130.105621] ---[ end trace 1d0bd69deb79164d ]---

Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: stable@kernel.org
Signed-off-by: default avatarMing Lei <tom.leiming@gmail.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      b2120914
    • Bob Liu's avatar
      USB: musb: blackfin: push clkin value to platform resources · 9c756462
      Bob Liu authored 
      In order to not touch the driver file for different xtal usage,
push the clkin value to board file and calculate the register
value instead of hardcoding it.
Signed-off-by: default avatarBob Liu <lliubbo@gmail.com>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      9c756462
    • Bob Liu's avatar
      USB: musb: blackfin: fix dynamic device<->host changing · 68f64714
      Bob Liu authored 
      We need to restart the timer in order to recognize USB devices in
host-only mode.
Signed-off-by: default avatarBob Liu <lliubbo@gmail.com>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      68f64714
    • Bob Liu's avatar
      USB: musb: blackfin: pm: make it work · 1e393c6e
      Bob Liu authored 
      Split the USB MMR init steps out into a helper func that both the platform
init and the resume code may call.

Then while suspending, the gpio_vrsel will change from high to low which
will generate a wakeup event and resume the system immediately, so we need
to manually drive it low before we sleep.
Signed-off-by: default avatarBob Liu <lliubbo@gmail.com>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      1e393c6e
    • Bob Liu's avatar
      USB: musb: pm: don't rely fully on clock support · 32d5dc95
      Bob Liu authored 
      Since clock support is optional across processors, don't make the whole
musb pm paths depend upon it.  Just conditionalize the clock accesses.
Signed-off-by: default avatarBob Liu <lliubbo@gmail.com>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      32d5dc95
    • Ian Jeffray's avatar
      USB: musb: blackfin: fix musb_read_txhubport() definition · 5d726f5a
      Ian Jeffray authored 
      The new MUSB power code needs musb_read_txhubport() to
return a value (so stub it as 0 like the other Blackfin
hub funcs).
Signed-off-by: default avatarIan Jeffray <ian@jeffray.co.uk>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      5d726f5a
    • Ming Lei's avatar
      USB: musb: gadget: fix MUSB_TXMAXP and MUSB_RXMAXP configuration · 31c9909b
      Ming Lei authored 
      Commit 9f445cb2[USB: musb: disable
double buffering for older RTL versions] tries to disable double
buffer mode by writing endpoint hw max packet size to TXMAP/RXMAP.

First the approach can break full speed and cause overflow problems.
We should always set those registers with the actual max packet size
from endpoint descriptor.

Second, the problem describe by commit 9f445cb2
was caused by musb gadget driver; nothing to do with RTL revision as
originaly suspected.

The real fix to the problem is to always use actual max packet
size from endpoint descriptor to config TXMAP/RXMAP registers.

Cc: Cliff Cai <cliff.cai@analog.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: default avatarMing Lei <tom.leiming@gmail.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      31c9909b
    • Grazvydas Ignotas's avatar
      usb: musb: don't leave PHY enabled on shutdown() · 120d074c
      Grazvydas Ignotas authored 
      Some actions like musb_platform_exit are only performed on module
removal and not on shutdown, which results in PHY being left enabled
on reboot at least. This is sometimes causing strange failures after
reboot (observed on OMAP3 pandora board), when DEVCTL does not report
VBUS state correctly due to unknown reasons (possibly because of
communication issues between musb IP and PHY). Running
musb_platform_exit before reset seems to resolve that issue.

Move some exit code from musb_remove() to musb_shutdown() so that it
is performed on both module removal and shutdown/reset. Also convert
the host check so that it doesn't need #ifdef.
Signed-off-by: default avatarGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      120d074c
    • Rahul Ruikar's avatar
      usb: musb: musb_gadget: fix resource leakage in error path · e2c34045
      Rahul Ruikar authored 
      In function musb_gadget_setup() call put_device()
when device_register() fails.
Signed-off-by: default avatarRahul Ruikar <rahul.ruikar@gmail.com>
Acked-by: default avatarMing Lei <tom.leiming@gmail.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      e2c34045
    • Ming Lei's avatar
      usb: musb: gadget: fix dma mode 0 in double buffer Rx case · 9001d80d
      Ming Lei authored 
      1, In Rx double buffer case, FIFO may have two packets, so
rxstate should be called to unload fifo if RXPKTRDY is set
even the current request has not been completed.

2, Commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85
introduces autoclear to support double buffer in dma mode 0,
so remove clearing RXPKTRDY manually for dma mode 0.

3, Commit c7af6b29ffeffbeb28caf39e5b2ce29b11807c7d may break
dma mode 1 for non-doublebuffer endpoint, fix it.

With this patch, either usbtest #5 or g_file_storage(writing
file to device in usb host) or g_ether have been tested OK in
double buffer case(using fifo mode 3). Also, this patch has
been verified that single buffer case can't be broken.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: default avatarMing Lei <tom.leiming@gmail.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      9001d80d
  7. 01 Nov, 2010 10 commits
  9. 31 Oct, 2010 14 commits
  11. 30 Oct, 2010 3 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7