The pullup does not need to be enabled at below situations:
- For platforms which the hardware pullup starts after setting
register even they do not see the VBUS. If the pullup is always
enabled for these platforms, it will consume more power and
break the USB IF compliance tests [1].
- For platforms which need to do BC 1.2 charger detection after
seeing the VBUS. Pullup D+ will break the charger detection
flow.
- For platforms which the system suspend is allowed when the
connection with host is there but the bus is not at suspend.
For these platforms, it is better to disable pullup when
entering the system suspend otherwise the host may confuse
the device behavior after controller is in low power mode.
Disable pullup is considered as a disconnection event from
host side.

[1] USB-IF Full and Low Speed Compliance Test Procedure
F Back-voltage Testing
Section 7.2.1 of the USB specification requires that no device
shall supply (source) current on VBUS at its upstream facing
port at any time. From VBUS on its upstream facing port,
a device may only draw (sink) current. They may not provide power
to the pull-up resistor on D+/D- unless VBUS is present (see
Section 7.1.5).
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201230051114.21370-1-peter.chen@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a use-after-free issue, if access udc_name
in function gadget_dev_desc_UDC_store after another context
free udc_name in function unregister_gadget.

Context 1:
gadget_dev_desc_UDC_store()->unregister_gadget()->
free udc_name->set udc_name to NULL

Context 2:
gadget_dev_desc_UDC_show()-> access udc_name

Call trace:
dump_backtrace+0x0/0x340
show_stack+0x14/0x1c
dump_stack+0xe4/0x134
print_address_description+0x78/0x478
__kasan_report+0x270/0x2ec
kasan_report+0x10/0x18
__asan_report_load1_noabort+0x18/0x20
string+0xf4/0x138
vsnprintf+0x428/0x14d0
sprintf+0xe4/0x12c
gadget_dev_desc_UDC_show+0x54/0x64
configfs_read_file+0x210/0x3a0
__vfs_read+0xf0/0x49c
vfs_read+0x130/0x2b4
SyS_read+0x114/0x208
el0_svc_naked+0x34/0x38

Add mutex_lock to protect this kind of scenario.
Signed-off-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1609239215-21819-1-git-send-email-macpaul.lin@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_gadget_deactivate/usb_gadget_activate does not execute the UDC start
operation, which may leave EP0 disabled and event IRQs disabled when
re-activating the function. Move the enabling/disabling of USB EP0 and
device event IRQs to be performed in the pullup routine.

Fixes: ae7e8610 ("usb: dwc3: Stop active transfers before halting the controller")
Tested-by: Michael Tretter <m.tretter@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reported-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609282837-21666-1-git-send-email-wcheng@codeaurora.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix shift out-of-bounds in vhci_hcd.c:

  UBSAN: shift-out-of-bounds in ../drivers/usb/usbip/vhci_hcd.c:399:41
  shift exponent 768 is too large for 32-bit type 'int'

Fixes: 03cd00d5 ("usbip: vhci-hcd: Set the vhci structure up to work")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: syzbot+297d20e437b79283bf6d@syzkaller.appspotmail.com
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201229071309.18418-1-rdunlap@infradead.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Stack-allocated buffers cannot be used for DMA (on all architectures).

Replace the HP-channel macro with a helper function that allocates a
dedicated transfer buffer so that it can continue to be used with
arguments from the stack.

Note that the buffer is cleared on allocation as usblp_ctrl_msg()
returns success also on short transfers (the buffer is only used for
debugging).

Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210104145302.2087-1-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dummy-hcd driver was written under the assumption that all the
parameters in URBs sent to its root hub would be valid.  With URBs
sent from userspace via usbfs, that assumption can be violated.

In particular, the driver doesn't fully check the port-feature values
stored in the wValue entry of Clear-Port-Feature and Set-Port-Feature
requests.  Values that are too large can cause the driver to perform
an invalid left shift of more than 32 bits.  Ironically, two of those
left shifts are unnecessary, because they implement Set-Port-Feature
requests that hubs are not required to support, according to section
11.24.2.13 of the USB-2.0 spec.

This patch adds the appropriate checks for the port feature selector
values and removes the unnecessary feature settings.  It also rejects
requests to set the TEST feature or to set or clear the INDICATOR and
C_OVERCURRENT features, as none of these are relevant to dummy-hcd's
root-hub emulation.

CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+5925509f78293baa7331@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201230162044.GA727759@rowland.harvard.eduSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With commit 913e4a90 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
wMaxPacketSize is computed dynamically but the value is never reset.

Because of this, the actual maximum packet size can only decrease each time
the audio gadget is instantiated.

Reset the endpoint maximum packet size and mark wMaxPacketSize as dynamic
to solve the problem.

Fixes: 913e4a90 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201221173531.215169-2-jbrunet@baylibre.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

First of all the commit e0082698 ("usb: dwc3: ulpi: conditionally
resume ULPI PHY") introduced the Suspend USB2.0 HS/FS/LS PHY regression,
as by design of the fix any attempt to read/write from/to the PHY control
registers will completely disable the PHY suspension, which consequently
will increase the USB bus power consumption. Secondly the fix won't work
well for the very first attempt of the ULPI PHY control registers IO,
because after disabling the USB2.0 PHY suspension functionality it will
still take some time for the bus to resume from the sleep state if one has
been reached before it. So the very first PHY register read/write
operation will take more time than the busy-loop provides and the IO
timeout error might be returned anyway.

Here we suggest to fix the denoted problems in the following way. First of
all let's not disable the Suspend USB2.0 HS/FS/LS PHY functionality so to
make the controller and the USB2.0 bus more power efficient. Secondly
instead of that we'll extend the PHY IO op wait procedure with 1 - 1.2 ms
sleep if the PHY suspension is enabled (1ms should be enough as by LPM
specification it is at most how long it takes for the USB2.0 bus to resume
from L1 (Sleep) state). Finally in case if the USB2.0 PHY suspension
functionality has been disabled on the DWC USB3 controller setup procedure
we'll compensate the USB bus resume process latency by extending the
busy-loop attempts counter.

Fixes: e0082698 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-4-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Originally the procedure of the ULPI transaction finish detection has been
developed as a simple busy-loop with just decrementing counter and no
delays. It's wrong since on different systems the loop will take a
different time to complete. So if the system bus and CPU are fast enough
to overtake the ULPI bus and the companion PHY reaction, then we'll get to
take a false timeout error. Fix this by converting the busy-loop procedure
to take the standard bus speed, address value and the registers access
mode into account for the busy-loop delay calculation.

Here is the way the fix works. It's known that the ULPI bus is clocked
with 60MHz signal. In accordance with [1] the ULPI bus protocol is created
so to spend 5 and 6 clock periods for immediate register write and read
operations respectively, and 6 and 7 clock periods - for the extended
register writes and reads. Based on that we can easily pre-calculate the
time which will be needed for the controller to perform a requested IO
operation. Note we'll still preserve the attempts counter in case if the
DWC USB3 controller has got some internals delays.

[1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1,
    October 20, 2004, pp. 30 - 36.

Fixes: 88bc9d19 ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone
bit when the PHY vendor control access is done and clears it when the
application initiates a new transaction. The doc doesn't say anything
about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover
we've discovered that the VStsBsy flag can be cleared before the VStsDone
bit. So using the former as a signal of the PHY control registers
completion might be dangerous. Let's have the VStsDone flag utilized
instead then.

[1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller
    Databook, 2.70a, December 2013, p.388

Fixes: 88bc9d19 ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to always cancel the control URB in write() so that it can be
reused after a timeout or spurious CMD_ACK.

Currently any further write requests after a timeout would fail after
triggering a WARN() in usb_submit_urb() when attempting to submit the
already active URB.

Reported-by: syzbot+e87ebe0f7913f71f2ea5@syzkaller.appspotmail.com
Fixes: 6bc235a2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Cc: stable <stable@vger.kernel.org>     # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

if of_find_device_by_node() succeed, usbmisc_get_init_data() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.

Fixes: ef12da91 ("usb: chipidea: imx: properly check for usbmisc")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201117011430.642589-1-yukuai3@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the MTU size issue with RX packet size as the host sends the packet
with extra bytes containing ethernet header. This causes failure when
user sets the MTU size to the maximum i.e. 15412. In this case the
ethernet packet received will be of length 15412 plus the ethernet header
length. This patch fixes the issue where there is a check that RX packet
length must not be more than max packet length.

Fixes: bba787a8 ("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1605597215-122027-1-git-send-email-manish.narani@xilinx.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If usb_otg_descriptor_alloc() failed, it need return ENOMEM.

Fixes: 578aa8a2 ("usb: gadget: acm_ms: allocate and init otg descriptor by otg capabilities")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201117092955.4102785-1-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a spinlock lockup as part of composite_disconnect
when it tries to acquire cdev->lock as part of usb_gadget_deactivate.
This is because the usb_gadget_deactivate is called from
usb_function_deactivate with the same spinlock held.

This would result in the below call stack and leads to stall.

rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu:     3-...0: (1 GPs behind) idle=162/1/0x4000000000000000
softirq=10819/10819 fqs=2356
 (detected by 2, t=5252 jiffies, g=20129, q=3770)
 Task dump for CPU 3:
 task:uvc-gadget_wlhe state:R  running task     stack:    0 pid:  674 ppid:
 636 flags:0x00000202
 Call trace:
  __switch_to+0xc0/0x170
  _raw_spin_lock_irqsave+0x84/0xb0
  composite_disconnect+0x28/0x78
  configfs_composite_disconnect+0x68/0x70
  usb_gadget_disconnect+0x10c/0x128
  usb_gadget_deactivate+0xd4/0x108
  usb_function_deactivate+0x6c/0x80
  uvc_function_disconnect+0x20/0x58
  uvc_v4l2_release+0x30/0x88
  v4l2_release+0xbc/0xf0
  __fput+0x7c/0x230
  ____fput+0x14/0x20
  task_work_run+0x88/0x140
  do_notify_resume+0x240/0x6f0
  work_pending+0x8/0x200

Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate
call from usb_function_deactivate.

The same lockup can happen in the usb_gadget_activate path. Fix that path
as well.
Reported-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When printer driver is loaded, the printer_func_bind function is called, in
this function, the interface descriptor be allocated memory, if after that,
the error occurred, the interface descriptor memory need to be free.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Link: https://lore.kernel.org/r/20201210020148.6691-1-qiang.zhang@windriver.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dwc3_meson_g12a_probe() does not invoke clk_bulk_disable_unprepare()
on one error handling path. This patch fixes that.

Fixes: 347052e3 ("usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20201215025459.91794-1-zhengzengkai@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The commit 0472bf06 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.

It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:

usb 1-2: can't set config #1, error -28

This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.

Fixes: 0472bf06 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Warm reboot scenarios some times type C Mux driver gets Mux configuration
request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure
Mux as follows as per IOM requirement:
 (1). Confgiure Mux HPD = 1, IRQ = 0
 (2). Configure Mux with HPD = 1, IRQ = 1

IOM expects TypeC Mux configuration as follows:
 (1). HPD=1, IRQ=0
 (2). HPD=1, IRQ=1
if IOM gets mux config request (2) without configuring (1), it will ignore
the request. The impact of this is there is no DP_alt mode display.

Fixes: 43d596e3 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

syzbot is reporting UAF at usb_submit_urb() [1], for
service_outstanding_interrupt() is not checking WDM_DISCONNECTING
before calling usb_submit_urb(). Close the race by doing same checks
wdm_read() does upon retry.

Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held,
service_interrupt_work() does not hold desc->rlock. Thus, it is possible
that usb_submit_urb() is called from service_outstanding_interrupt() from
service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs()
 from wdm_disconnect() completed. Thus, move kill_urbs() in
wdm_disconnect() to after cancel_work_sync() (which makes sure that
service_interrupt_work() is no longer running) completed.

Although it seems to be safe to dereference desc->intf->dev in
service_outstanding_interrupt() even if WDM_DISCONNECTING was already set
because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from
reaching list_del() before service_outstanding_interrupt() completes,
let's not emit error message if WDM_DISCONNECTING is set by
wdm_disconnect() while usb_submit_urb() is in progress.

[1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661dafReported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jpSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since 5.10-rc1 i.MX is a devicetree-only platform, and this driver
was only used by the old non-DT i.MX devices.

Remove the driver as it has no users left.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201210210413.15262-1-festevam@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add compatible string in j721e-usb binding file as the same USB subsystem
is present in AM64.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20201215042549.7956-1-a-govindraju@ti.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Updates my email address for Cadence USB3 driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20201218105736.17667-1-rogerq@ti.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This device is supported by the IR Toy driver.
Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201227134502.4548-2-sean@mess.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 36e2c742 ("fs: don't allow splice read/write without
explicit ops") we've required that file operation structures explicitly
enable splice support, rather than falling back to the default handlers.

Most /proc files use the indirect 'struct proc_ops' to describe their
file operations, and were fixed up to support splice earlier in commits
40be821d..b24c30c6, but the mountinfo files interact with the
VFS directly using their own 'struct file_operations' and got missed as
a result.

This adds the necessary support for splice to work for /proc/*/mountinfo
and friends.
Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NTB fixes from Jon Mason:
 "Bug fix for IDT NTB and Intel NTB LTR management support"

* tag 'ntb-5.11' of git://github.com/jonmason/ntb:
  ntb: intel: add Intel NTB LTR vendor support for gen4 NTB
  ntb: idt: fix error check in ntb_hw_idt.c

Pull crypto fixes from Herbert Xu:
 "Fix a number of autobuild failures due to missing Kconfig
  dependencies"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: qat - add CRYPTO_AES to Kconfig dependencies
  crypto: keembay - Add dependency on HAS_IOMEM
  crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY

Pull objtool fix from Ingo Molnar:
 "Fix a segfault that occurs when built with Clang"

* tag 'objtool-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix seg fault with Clang non-section symbols

Pull locking fixes from Ingo Molnar:
 "Misc fixes/updates:

   - Fix static keys usage in module __init sections

   - Add separate MAINTAINERS entry for static branches/calls

   - Fix lockdep splat with CONFIG_PREEMPTIRQ_EVENTS=y tracing"

* tag 'locking-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  softirq: Avoid bad tracing / lockdep interaction
  jump_label/static_call: Add MAINTAINERS
  jump_label: Fix usage in module __init

Pull timer fixes from Ingo Molnar:
 "Update/fix two CPU sanity checks in the hotplug and the boot code, and
  fix a typo in the Kconfig help text.

  [ Context: the first two commits are the result of an ongoing
    annotation+review work of (intentional) tick_do_timer_cpu() data
    races reported by KCSAN, but the annotations aren't fully cooked
    yet ]"

* tag 'timers-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix spelling mistake in Kconfig "fullfill" -> "fulfill"
  tick/sched: Remove bogus boot "safety" check
  tick: Remove pointless cpu valid check in hotplug code

Pull scheduler fix from Ingo Molnar:
 "Fix a context switch performance regression"

* tag 'sched-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Optimize finish_lock_switch()

Commit c9a3c4e6 ("mfd: ab8500-debugfs: Remove extraneous curly
brace") removed a left-over curly brace that caused build failures, but
Joe Perches points out that the subsequent 'seq_putc()' should also be
removed, because the commit that caused all these problems already added
the final '\n' to the seq_printf() above it.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 886c8121 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull PCI fixes from Bjorn Helgaas:

 - Fix a tegra enumeration regression (Rob Herring)

 - Fix a designware-host check that warned on *success*, not failure
   (Alexander Lobakin)

* tag 'pci-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: dwc: Fix inverted condition of DMA mask setup warning
  PCI: tegra: Fix host link initialization

Clang errors:

  drivers/mfd/ab8500-debugfs.c:1526:2: error: non-void function does not return a value [-Werror,-Wreturn-type]
          }
          ^
  drivers/mfd/ab8500-debugfs.c:1528:2: error: expected identifier or '('
  return 0;
          ^
  drivers/mfd/ab8500-debugfs.c:1529:1: error: extraneous closing brace ('}')
  }
  ^
  3 errors generated.

The cleanup in ab8500_interrupts_show left a curly brace around, remove
it to fix the error.

Fixes: 886c8121 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 660c4865 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.

Fix this by inverting the condition.

[bhelgaas: join string to make it greppable]
Fixes: 660c4865 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.meSigned-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Commit b9ac0f9d ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:

In non-working case (next-20201211):

  0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
  0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
  0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)

In working case (v5.10-rc7):

  0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
  0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
  0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
  0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
  0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
  0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)

The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.

Fixes: b9ac0f9d ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.orgReported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>

clang (quite rightly) complains fairly loudly about the newly added
mpc1_get_mpc_out_mux() function returning an uninitialized value if the
'opp_id' checks don't pass.

This may not happen in practice, but the code really shouldn't return
garbage if the sanity checks don't pass.

So just initialize 'val' to zero to avoid the issue.

Fixes: 110b055b ("drm/amd/display: add getter routine to retrieve mpcc mux")
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: Bindu Ramamurthy <bindu.r@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more perf tools updates from Arnaldo Carvalho de Melo:

 - Refactor 'perf stat' per CPU/socket/die/thread aggregation fixing use
   cases in ARM machines.

 - Fix memory leak when synthesizing SDT probes in 'perf probe'.

 - Update kernel header copies related to KVM, epol_pwait. msr-index and
   powerpc and s390 syscall tables.

* tag 'perf-tools-2020-12-24' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (24 commits)
  perf probe: Fix memory leak when synthesizing SDT probes
  perf stat aggregation: Add separate thread member
  perf stat aggregation: Add separate core member
  perf stat aggregation: Add separate die member
  perf stat aggregation: Add separate socket member
  perf stat aggregation: Add separate node member
  perf stat aggregation: Start using cpu_aggr_id in map
  perf cpumap: Drop in cpu_aggr_map struct
  perf cpumap: Add new map type for aggregation
  perf stat: Replace aggregation ID with a struct
  perf cpumap: Add new struct for cpu aggregation
  perf cpumap: Use existing allocator to avoid using malloc
  perf tests: Improve topology test to check all aggregation types
  perf tools: Update s390's syscall.tbl copy from the kernel sources
  perf tools: Update powerpc's syscall.tbl copy from the kernel sources
  perf s390: Move syscall.tbl check into check-headers.sh
  perf powerpc: Move syscall.tbl check to check-headers.sh
  tools headers UAPI: Synch KVM's svm.h header with the kernel
  tools kvm headers: Update KVM headers from the kernel sources
  tools headers UAPI: Sync KVM's vmx.h header with the kernel sources
  ...

Pull coccinelle updates from Julia Lawall.

* 'for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  scripts: coccicheck: Correct usage of make coccicheck
  coccinelle: update expiring email addresses
  coccinnelle: Remove ptr_ret script
  kbuild: do not use scripts/ld-version.sh for checking spatch version
  remove boolinit.cocci