- 21 Oct, 2017 15 commits
-
-
Brian Masney authored
The functions tsl2x7x_invoke_change() and tsl2x7x_prox_calculate() are short enough that the return value and static declaration can be moved onto the same line with the function name. This patch makes that change to increase code readability. Signed-off-by:
Brian Masney <masneyb@onstation.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Brian Masney authored
Correct the alignment of the break statements to match the alignment of the rest of the code within the case statements. Signed-off-by:
-
Brian Masney authored
The LED power defines are named like TSL2X7X_mAXXX. Rename these values to TSL2X7X_XXX_mA to improve code readability. Signed-off-by:
-
Brian Masney authored
Correct error from checkpatch.pl to improve code readibility: Alignment should match open parenthesis. An unnecessary cast to 'struct tsl2x7x_lux *' was removed and the return value of static definition of in_illuminance0_calibscale_available_show() was put on its own line due to the length of that sysfs attribute. Signed-off-by:
-
Brian Masney authored
Correct error from checkpatch.pl to improve code readibility: Alignment should match open parenthesis. This involved shortening the name of tsl2x7x_als_gainadj and tsl2x7x_prx_gainadj to tsl2x7x_als_gain and tsl2x7x_prx_gain respectively. This also required removing the ch0lux and ch1lux local variables in order to get the line short enough. Signed-off-by:
-
Brian Masney authored
This patch fixes the error 'Unnecessary parentheses around 'XXX' from checkpatch.pl. It also fixes several other places with unnecessary parentheses that checkpatch.pl did not detect. Signed-off-by:
-
Brian Masney authored
The sysfs attribute in_proximity0_calibscale_available is currently created by using DEVICE_ATTR_RO(). Convert this over to use IIO_CONST_ATTR(). Signed-off-by:
-
Brian Masney authored
Some of the existing #defines have tabs between the name, and the value, while others have spaces. The alignment of the values mostly has a consistent layout, but there are some that don't. Change all of the defines so that the name and value is separated by tabs and all of the values start on the same column to increase code readability. This patch also removes the unnecessary parentheses around the value of TSL2X7X_MAX_TIMER_CNT. Signed-off-by:
-
Brian Masney authored
tsl2x7x.h has a blank definition for 'struct iio_dev' that is not needed. This patch removes that definition. Signed-off-by:
-
Brian Masney authored
Sort the #include statements for increased code readability. Signed-off-by:
-
Brian Masney authored
The structure tsl2x7x_parse_result is not used so this patch removes its definition. Signed-off-by:
-
Brian Masney authored
The sysfs attributes in_intensity0_thresh_period and in_proximity0_thresh_period are currently directly created by the driver. This patch migrates the creation of these sysfs attributes from the driver to using the IIO core via iio_event_spec. Signed-off-by:
-
Colin Ian King authored
Don't populate const array ch_to_mux on the stack, instead make it static. Makes the object code smaller by over 200 bytes: Before: text data bss dec hex filename 12663 1648 128 14439 3867 drivers/iio/adc/ti-adc12138.o After text data bss dec hex filename 12353 1744 128 14225 3791 drivers/iio/adc/ti-adc12138.o (gcc version 7.2.0 x86_64) Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Fabrice Gasnier authored
Add check on STM32 ADC clock rate to report an explicit error. This may avoid division by 0 later in stm32-adc driver. Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
-
Fabrice Gasnier authored
Add TIM15_TRGO trigger that is now supported on STM32H7. Signed-off-by:
-
- 14 Oct, 2017 7 commits
-
-
Gwendal Grignou authored
Add driver to support older EC firmware that only support deprecated ec command. Rely on ACPI memory map register to access sensor information. Present same interface as the regular cros_ec sensor stack: - one iio device per accelerometer - use HTML5 axis definition - use iio abi units - accept calibration calls, but do nothing Chrome can use the same code than regular cros_ec sensor stack to calculate orientation and lid angle. Signed-off-by:
Gwendal Grignou <gwendal@chromium.org> Signed-off-by:
Thierry Escande <thierry.escande@collabora.com> Signed-off-by:
-
Srinivas Pandruvada authored
One of the user complained that on his system Thinkpad Yoga S1, with commit f1664eaa ("iio: hid-sensor-trigger: Fix the race with user space powering up sensors") causes the system to resume immediately on suspend (S3 operation). On this system the sensor hub is on USB and is a wake up device from S3. So if any sensor sends data on motion, the system will wake up. This can be a legitimate use case to wake up device motion, but that needs proper user space support to set right thresholds. In fact the above commit didn't cause this regression, but any operation which cause sensors to wake up would have caused the same issue. So if user reads the raw sensor data, same issue occurs, with or without this commit. Only difference is that the above commit by default will trigger a power up and power down of sensors as part of runtime pm enable (runtime enable will cause a runtime resume callback followed by runtime_suspend callback). Previously user has to do some action on sensors. On investigation it was observed that the current driver correctly changing the state of all sensors to power off but then also some sensor will still send some data. Only option is to never power up any sensor. Only good option is to: - Using sysfs interface disable USB as a wakeup device (This will not need any driver change) Since some user don't care about sensors. So for those users this change brings back old functionality. As long as they don't cause any operation to power up sensors (like raw read or start iio-sensor-proxy service), the sensors will not be to touched. This is done by delaying run time enable till user space does some operation with sensors. Link: https://bugzilla.kernel.org/show_bug.cgi?id=196853Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
Peter Meerwald-Stadler <pmeerw@pmeerw.net> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Peter Meerwald-Stadler authored
Should be in hex, not decimal or even octal Signed-off-by:
-
Lukas Wunner authored
Commit 5f420b42 ("staging:iio: Add extended IIO channel info") added a forward declaration for struct iio_dev to <linux/iio/iio.h> but forgot to remove an existing forward declaration further down originating from commit 7ae8cf62 ("staging: iio: chrdev.h rationalization"). Cc: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Lukas Wunner <lukas@wunner.de> Signed-off-by:
-
Peter Meerwald-Stadler authored
Driver for RF Digital RFD77402 VCSEL (vertical-cavity surface-emitting laser) Time-of-Flight (ToF) sensor to measure distance up to 2 m with millimeter precision Signed-off-by:
-
Peter Meerwald-Stadler authored
IIO_DISTANCE is used for two purposes: for pedometers to record the distance covered by a walker, and to measure the distance to an object IIO_DISTANCE is in meters while IIO_PROXIMITY is a unitless measure indirectly proportional to distance (higher value relates to a closer object) Signed-off-by:
-
- 10 Oct, 2017 7 commits
-
-
Lorenzo Bianconi authored
Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@st.com> Acked-by:
-
Lorenzo Bianconi authored
add support to STMicroelectronics LIS3DHH accel sensor http://www.st.com/resource/en/datasheet/lis3dhh.pdfSigned-off-by:
-
Lorenzo Bianconi authored
Do not try to configure sample frequency if the sensor do not export odr register address in register map. That change will be used to properly support LIS3DHH accel sensor. Signed-off-by:
-
Lorenzo Bianconi authored
Define st_sensor_int_drdy structure in st_sensor_data_ready_irq in order to contain irq line parameters of the device. Moreover separate data-ready open-drain configuration parameters for INT1 and INT2 pins in st_sensor_data_ready_irq data structure. That change will be used to properly support LIS3DHH accel sensor. Signed-off-by:
-
Lorenzo Bianconi authored
Add SPI Serial Interface Mode (SIM) register information to STM pressure framework Signed-off-by:
-
Lorenzo Bianconi authored
Add SPI Serial Interface Mode (SIM) register information to LIS3MDL magn sensor Signed-off-by:
-
Lorenzo Bianconi authored
Add SPI Serial Interface Mode (SIM) register information to STM gyroscope framework Signed-off-by:
-
- 09 Oct, 2017 11 commits
-
-
Lorenzo Bianconi authored
Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Lorenzo Bianconi authored
add support to STMicroelectronics LIS2DW12 accelerometer in st_accel framework http://www.st.com/resource/en/datasheet/lis2dw12.pdfSigned-off-by:
-
Lorenzo Bianconi authored
New devices (e.g. LIS2DW12) enable all axis by default and do not export that capability in register map. Check if the enable_axis register address has been declared in st_sensor_settings map in order to verify if the driver needs to enable all sensor axis Signed-off-by:
-
Lorenzo Bianconi authored
Separate data-ready configuration parameters for INT1 and INT2 pins in st_sensor_data_ready_irq data structure. That change will be use to properly support LIS2DW12 accel sensor. Signed-off-by:
-
Lorenzo Bianconi authored
Introduce register mask for data-ready status register since pressure sensors (e.g. LPS22HB) export just two channels (BIT(0) and BIT(1)) and BIT(2) is marked reserved while in st_sensors_new_samples_available() value read from status register is masked using 0x7. Moreover do not mask status register using active_scan_mask since now status value is properly masked and if the result is not zero the interrupt has to be consumed by the driver. This fix an issue on LPS25H and LPS331AP where channel definition is swapped respect to status register. Furthermore that change allows to properly support new devices (e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register to figure out if the interrupt has been generated by the device. Fixes: 97865fe4 (iio: st_sensors: verify interrupt event to status) Signed-off-by:
-
Lukas Wunner authored
These ADCs are marketed as single-channel 22 bit delta-sigma ADCs, but in reality their resolution is 21 bit with an overrange or underrange of 12% beyond Vref. In other words, "full scale" means +/- 2^20. This driver does not explicitly signal back to the user when an overrange or underrange occurs, but the user can detect it by comparing the raw value to +/- 2^20 (or the scaled value to Vref). The chips feature an extended temperature range and high accuracy, low noise characteristics, but their conversion times are slow with up to 80 ms +/- 2% (on the MCP3550-50). Hence, unlike the other ADCs supported by the driver, conversion does not take place in realtime upon lowering CS. Instead, CS is asserted for 8 usec to start the conversion. After waiting for the duration of the conversion, the result can be fetched. While waiting, control of the bus is ceased so it may be used by a different device. After the result has been fetched and 10 us have passed, the chip goes into shutdown and an additional power-up delay of 144 clock periods is then required to wake the analog circuitry upon the next conversion (footnote below table 4-1, page 16 in the spec). Optionally, the chips can be used in so-called "continuous conversion mode": Conversions then take place continuously and the last result may be fetched at any time without observing a delay. The mode is enabled by permanently driving CS low, e.g. by wiring it to ground. The driver only supports "single conversion mode" for now but should be adaptable to "continuous conversion mode" with moderate effort. The chips clock out a 3 byte word, unlike the other ADCs supported by the driver which all have a lower resolution than 16 bit and thus make do with 2 bytes. Calculate the word length on probe by rounding up the resolution to full bytes. Crucially, if the clock idles low, the transfer is preceded by a useless Data Ready bit which increases its length from 24 bit to 25 bit = 4 bytes (section 5.5 in the spec). Autosense this based on the SPI slave's configuration. Cc: Mathias Duckeck <m.duckeck@kunbus.de> Signed-off-by:
-
Aastha Gupta authored
The IIO subsystem is redefining iio_dev->mlock to be used by the IIO core only for protecting device operating mode changes. ie. Changes between INDIO_DIRECT_MODE, INDIO_BUFFER_* modes. In this driver, mlock was being used to protect hardware state changes. Replace it with a driver private lock. Also, as there are state changes in the ad7192_ write_raw function, a lock is added to prevent the concurrent state changes. Signed-off-by:
Aastha Gupta <aastha.gupta4104@gmail.com> Signed-off-by:
-
Stefan Brüns authored
According to the ABI documentation, the shunt resistor value should be specificied in Ohm. As this is also used/documented for the MAX9611, use the same for the INA2xx driver. This poses an ABI break for anyone actually altering the shunt value through the sysfs interface, it does not alter the default value nor a value set from the devicetree. Minor change: Fix comment, 1mA is 10^-3A. Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
-
Lorenzo Bianconi authored
Introduce FIFO ops data structure to contain FIFO related parameters in order to properly support more devices in st_lsm6dsx driver Signed-off-by:
-
Lorenzo Bianconi authored
Move FIFO decimator info in st_lsm6dsx_sensor_settings list since decimator registers are exported in register map just in lsm6ds3/lsm6ds3h/lsm6dsl/lsm6dsm sensors and not in other compliant devices Signed-off-by:
-
Lorenzo Bianconi authored
Separate fifo mode and max fifo sample rate configuration. That change will be necessary to reuse st_lsm6dsx_set_fifo_mode() routine and to support more devices in st_lsm6dsx driver Signed-off-by:
-
