- 30 Jul, 2022 14 commits
-
-
Edward Cree authored
It's not truly a ring, but the maximum length of the list of queued RX SKBs is analogous to an RX ring size, so use that API to configure it. Signed-off-by:
Edward Cree <ecree.xilinx@gmail.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Edward Cree authored
Representors do not want to be subject to the PF's Ethernet address filters, since traffic from VFs will typically have a destination either elsewhere on the link segment or on an overlay network. So, create a dynamic m-port with promiscuous and all-multicast filters, and set it as the egress port of representor default rules. Since the m-port is an alias of the calling PF's own m-port, traffic will still be delivered to the PF's RXQs, but it will be subject to the VNRX filter rules installed on the dynamic m-port (specified by the v-port ID field of the filter spec). Signed-off-by:
-
Edward Cree authored
We need to be able to drop the efx->filter_sem in ef100_filter_table_up() so that we can call functions that insert filters (and thus take that rwsem for read), which means the efx->type->filter_table_probe method needs to be responsible for taking the lock in the first place. Signed-off-by:
-
Edward Cree authored
Default rules are low-priority switching rules which the hardware uses in the absence of higher-priority rules. Each representor requires a corresponding rule matching traffic from its representee VF and delivering to the PF (where a check on INGRESS_MPORT in __ef100_rx_packet() will direct it to the representor). No rule is required in the reverse direction, because representor TX uses a TX override descriptor to bypass the MAE and deliver directly to the VF. Since inserting any rule into the MAE disables the firmware's own default rules, also insert a pair of rules to connect the PF to the physical network port and vice-versa. Signed-off-by:
-
Edward Cree authored
If the source m-port of a packet in __ef100_rx_packet() is a VF, hand off the packet to the corresponding representor with efx_ef100_rep_rx_packet(). Signed-off-by:
-
Edward Cree authored
If not, for now drop them and warn. A subsequent patch will look up the source m-port to try and find a representor to deliver them to. Signed-off-by:
-
Edward Cree authored
Traffic delivered to the (MAE admin) PF could be from either the wire or a VF. The INGRESS_MPORT field of the RX prefix distinguishes these; base_mport is the value this field will have for traffic from the wire (which should be delivered to the PF's netdevice, not a representor). Signed-off-by:
-
Edward Cree authored
Representor RX uses a NAPI context driven by a 'fake interrupt': when the parent PF receives a packet destined for the representor, it adds it to an SKB list (efv->rx_list), and schedules NAPI if the 'fake interrupt' is primed. The NAPI poll then pulls packets off this list and feeds them to the stack with netif_receive_skb_list(). This scheme allows us to decouple representor RX from the parent PF's RX fast-path. This patch implements the 'top half', which builds an SKB, copies data into it from the RX buffer (which can then be released), adds it to the queue and fires the 'fake interrupt' if necessary. Signed-off-by:
-
Edward Cree authored
This patch adds the 'bottom half' napi->poll routine for representor RX. See the next patch (with the top half) for an explanation of the 'fake interrupt' scheme used to drive this NAPI context. Signed-off-by:
-
Edward Cree authored
Implement .ndo_get_stats64() method to read values out of struct efx_rep_sw_stats. Signed-off-by:
-
Dan Carpenter authored
The "ret" variable needs to be initialized at the start. Fixes: 52323ef7 ("net: marvell: prestera: add phylink support") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/YuKeBBuGtsmd7QdT@kiliSigned-off-by:
-
Yu Zhe authored
Use "jiffies != now" to replace "jiffies - now > 0" to make code more readable. We want to put a limit on how long the loop can run for before rescheduling. Signed-off-by:
Yu Zhe <yuzhe@nfschina.com> Link: https://lore.kernel.org/r/20220729061712.22666-1-yuzhe@nfschina.comSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'wireless-next-2022-07-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v5.20 Fourth set of patches for v5.20, last few patches before the merge window. Only driver changes this time, mostly just fixes and cleanup. Major changes: brcmfmac - support brcm,ccode-map-trivial DT property wcn36xx - add debugfs file to show firmware feature strings * tag 'wireless-next-2022-07-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (36 commits) wifi: rtw88: check the return value of alloc_workqueue() wifi: rtw89: 8852a: adjust IMR for SER L1 wifi: rtw89: 8852a: update RF radio A/B R56 wifi: wcn36xx: Add debugfs entry to read firmware feature strings wifi: wcn36xx: Move capability bitmap to string translation function to firmware.c wifi: wcn36xx: Move firmware feature bit storage to dedicated firmware.c file wifi: wcn36xx: Rename clunky firmware feature bit enum wifi: brcmfmac: prevent double-free on hardware-reset wifi: brcmfmac: support brcm,ccode-map-trivial DT property dt-bindings: bcm4329-fmac: add optional brcm,ccode-map-trivial wifi: brcmfmac: Replace default (not configured) MAC with a random MAC wifi: brcmfmac: Add brcmf_c_set_cur_etheraddr() helper wifi: brcmfmac: Remove #ifdef guards for PM related functions wifi: brcmfmac: use strreplace() in brcmf_of_probe() wifi: plfxlc: Use eth_zero_addr() to assign zero address wifi: wilc1000: use existing iftype variable to store the interface type wifi: wilc1000: add 'isinit' flag for SDIO bus similar to SPI wifi: wilc1000: cancel the connect operation during interface down wifi: wilc1000: get correct length of string WID from received config packet wifi: wilc1000: set station_info flag only when signal value is valid ... ==================== Link: https://lore.kernel.org/r/20220729192832.A5011C433D6@smtp.kernel.orgSigned-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski authored
Andrii Nakryiko says: ==================== bpf-next 2022-07-29 We've added 22 non-merge commits during the last 4 day(s) which contain a total of 27 files changed, 763 insertions(+), 120 deletions(-). The main changes are: 1) Fixes to allow setting any source IP with bpf_skb_set_tunnel_key() helper, from Paul Chaignon. 2) Fix for bpf_xdp_pointer() helper when doing sanity checking, from Joanne Koong. 3) Fix for XDP frame length calculation, from Lorenzo Bianconi. 4) Libbpf BPF_KSYSCALL docs improvements and fixes to selftests to accommodate s390x quirks with socketcall(), from Ilya Leoshkevich. 5) Allow/denylist and CI configs additions to selftests/bpf to improve BPF CI, from Daniel Müller. 6) BPF trampoline + ftrace follow up fixes, from Song Liu and Xu Kuohai. 7) Fix allocation warnings in netdevsim, from Jakub Kicinski. 8) bpf_obj_get_opts() libbpf API allowing to provide file flags, from Joe Burton. 9) vsnprintf usage fix in bpf_snprintf_btf(), from Fedor Tokarev. 10) Various small fixes and clean ups, from Daniel Müller, Rongguang Wei, Jörn-Thorben Hinz, Yang Li. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (22 commits) bpf: Remove unneeded semicolon libbpf: Add bpf_obj_get_opts() netdevsim: Avoid allocation warnings triggered from user space bpf: Fix NULL pointer dereference when registering bpf trampoline bpf: Fix test_progs -j error with fentry/fexit tests selftests/bpf: Bump internal send_signal/send_signal_tracepoint timeout bpftool: Don't try to return value from void function in skeleton bpftool: Replace sizeof(arr)/sizeof(arr[0]) with ARRAY_SIZE macro bpf: btf: Fix vsnprintf return value check libbpf: Support PPC in arch_specific_syscall_pfx selftests/bpf: Adjust vmtest.sh to use local kernel configuration selftests/bpf: Copy over libbpf configs selftests/bpf: Sort configuration selftests/bpf: Attach to socketcall() in test_probe_user libbpf: Extend BPF_KSYSCALL documentation bpf, devmap: Compute proper xdp_frame len redirecting frames bpf: Fix bpf_xdp_pointer return pointer selftests/bpf: Don't assign outer source IP to host bpf: Set flow flag to allow any source IP in bpf_tunnel_key geneve: Use ip_tunnel_key flow flags in route lookups ... ==================== Link: https://lore.kernel.org/r/20220729230948.1313527-1-andrii@kernel.orgSigned-off-by:
-
- 29 Jul, 2022 26 commits
-
-
Yang Li authored
Eliminate the following coccicheck warning: /kernel/bpf/trampoline.c:101:2-3: Unneeded semicolon Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Signed-off-by:
Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20220725222733.55613-1-yang.lee@linux.alibaba.com
-
Joe Burton authored
Add an extensible variant of bpf_obj_get() capable of setting the `file_flags` parameter. This parameter is needed to enable unprivileged access to BPF maps. Without a method like this, users must manually make the syscall. Signed-off-by:
Joe Burton <jevburton@google.com> Signed-off-by:
-
Jakub Kicinski authored
We need to suppress warnings from sily map sizes. Also switch from GFP_USER to GFP_KERNEL_ACCOUNT, I'm pretty sure I misunderstood the flags when writing this code. Fixes: 395cacb5 ("netdevsim: bpf: support fake map offload") Reported-by: syzbot+ad24705d3fd6463b18c6@syzkaller.appspotmail.com Signed-off-by:
-
Xu Kuohai authored
A panic was reported on arm64: [ 44.517109] audit: type=1334 audit(1658859870.268:59): prog-id=19 op=LOAD [ 44.622031] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010 [ 44.624321] Mem abort info: [ 44.625049] ESR = 0x0000000096000004 [ 44.625935] EC = 0x25: DABT (current EL), IL = 32 bits [ 44.627182] SET = 0, FnV = 0 [ 44.627930] EA = 0, S1PTW = 0 [ 44.628684] FSC = 0x04: level 0 translation fault [ 44.629788] Data abort info: [ 44.630474] ISV = 0, ISS = 0x00000004 [ 44.631362] CM = 0, WnR = 0 [ 44.632041] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000100ab5000 [ 44.633494] [0000000000000010] pgd=0000000000000000, p4d=0000000000000000 [ 44.635202] Internal error: Oops: 96000004 [#1] SMP [ 44.636452] Modules linked in: xfs crct10dif_ce ghash_ce virtio_blk virtio_console virtio_mmio qemu_fw_cfg [ 44.638713] CPU: 2 PID: 1 Comm: systemd Not tainted 5.19.0-rc7 #1 [ 44.640164] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 [ 44.641799] pstate: 00400005 (nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 44.643404] pc : ftrace_set_filter_ip+0x24/0xa0 [ 44.644659] lr : bpf_trampoline_update.constprop.0+0x428/0x4a0 [ 44.646118] sp : ffff80000803b9f0 [ 44.646950] x29: ffff80000803b9f0 x28: ffff0b5d80364400 x27: ffff80000803bb48 [ 44.648721] x26: ffff8000085ad000 x25: ffff0b5d809d2400 x24: 0000000000000000 [ 44.650493] x23: 00000000ffffffed x22: ffff0b5dd7ea0900 x21: 0000000000000000 [ 44.652279] x20: 0000000000000000 x19: 0000000000000000 x18: ffffffffffffffff [ 44.654067] x17: 0000000000000000 x16: 0000000000000000 x15: ffffffffffffffff [ 44.655787] x14: ffff0b5d809d2498 x13: ffff0b5d809d2432 x12: 0000000005f5e100 [ 44.657535] x11: abcc77118461cefd x10: 000000000000005f x9 : ffffa7219cb5b190 [ 44.659254] x8 : ffffa7219c8e0000 x7 : 0000000000000000 x6 : ffffa7219db075e0 [ 44.661066] x5 : ffffa7219d3130e0 x4 : ffffa7219cab9da0 x3 : 0000000000000000 [ 44.662837] x2 : 0000000000000000 x1 : ffffa7219cb7a5c0 x0 : 0000000000000000 [ 44.664675] Call trace: [ 44.665274] ftrace_set_filter_ip+0x24/0xa0 [ 44.666327] bpf_trampoline_update.constprop.0+0x428/0x4a0 [ 44.667696] __bpf_trampoline_link_prog+0xcc/0x1c0 [ 44.668834] bpf_trampoline_link_prog+0x40/0x64 [ 44.669919] bpf_tracing_prog_attach+0x120/0x490 [ 44.671011] link_create+0xe0/0x2b0 [ 44.671869] __sys_bpf+0x484/0xd30 [ 44.672706] __arm64_sys_bpf+0x30/0x40 [ 44.673678] invoke_syscall+0x78/0x100 [ 44.674623] el0_svc_common.constprop.0+0x4c/0xf4 [ 44.675783] do_el0_svc+0x38/0x4c [ 44.676624] el0_svc+0x34/0x100 [ 44.677429] el0t_64_sync_handler+0x11c/0x150 [ 44.678532] el0t_64_sync+0x190/0x194 [ 44.679439] Code: 2a0203f4 f90013f5 2a0303f5 f9001fe1 (f9400800) [ 44.680959] ---[ end trace 0000000000000000 ]--- [ 44.682111] Kernel panic - not syncing: Oops: Fatal exception [ 44.683488] SMP: stopping secondary CPUs [ 44.684551] Kernel Offset: 0x2721948e0000 from 0xffff800008000000 [ 44.686095] PHYS_OFFSET: 0xfffff4a380000000 [ 44.687144] CPU features: 0x010,00022811,19001080 [ 44.688308] Memory Limit: none [ 44.689082] ---[ end Kernel panic - not syncing: Oops: Fatal exception ]--- It's caused by a NULL tr->fops passed to ftrace_set_filter_ip(). tr->fops is initialized to NULL and is assigned to an allocated memory address if CONFIG_DYNAMIC_FTRACE_WITH_DIRECT_CALLS is enabled. Since there is no direct call on arm64 yet, the config can't be enabled. To fix it, call ftrace_set_filter_ip() only if tr->fops is not NULL. Fixes: 00963a2e ("bpf: Support bpf_trampoline on functions with IPMODIFY (e.g. livepatch)") Reported-by:
Bruno Goncalves <bgoncalv@redhat.com> Signed-off-by:
Xu Kuohai <xukuohai@huawei.com> Signed-off-by:
Song Liu <songliubraving@fb.com> Acked-by:
Jiri Olsa <jolsa@kernel.org> Link: https://lore.kernel.org/bpf/20220728114048.3540461-1-xukuohai@huaweicloud.com
-
Song Liu authored
When multiple threads are attaching/detaching fentry/fexit programs to the same trampoline, we may call register_fentry on the same trampoline twice: register_fentry(), unregister_fentry(), then register_fentry again. This causes ftrace_set_filter_ip() for the same ip on tr->fops twice, which leaves duplicated ip in tr->fops. The extra ip is not cleaned up properly on unregister and thus causes failures with further register in register_ftrace_direct_multi(): register_ftrace_direct_multi() { ... for (i = 0; i < size; i++) { hlist_for_each_entry(entry, &hash->buckets[i], hlist) { if (ftrace_find_rec_direct(entry->ip)) goto out_unlock; } } ... } This can be triggered with parallel fentry/fexit tests with test_progs: ./test_progs -t fentry,fexit -j Fix this by resetting tr->fops in ftrace_set_filter_ip(), so that there will never be duplicated entries in tr->fops. Fixes: 00963a2e ("bpf: Support bpf_trampoline on functions with IPMODIFY (e.g. livepatch)") Reported-by:Song Liu <song@kernel.org> Signed-off-by:
-
Daniel Müller authored
The send_signal/send_signal_tracepoint is pretty flaky, with at least one failure in every ten runs on a few attempts I've tried it: > test_send_signal_common:PASS:pipe_c2p 0 nsec > test_send_signal_common:PASS:pipe_p2c 0 nsec > test_send_signal_common:PASS:fork 0 nsec > test_send_signal_common:PASS:skel_open_and_load 0 nsec > test_send_signal_common:PASS:skel_attach 0 nsec > test_send_signal_common:PASS:pipe_read 0 nsec > test_send_signal_common:PASS:pipe_write 0 nsec > test_send_signal_common:PASS:reading pipe 0 nsec > test_send_signal_common:PASS:reading pipe error: size 0 0 nsec > test_send_signal_common:FAIL:incorrect result unexpected incorrect result: actual 48 != expected 50 > test_send_signal_common:PASS:pipe_write 0 nsec > #139/1 send_signal/send_signal_tracepoint:FAIL The reason does not appear to be a correctness issue in the strict sense. Rather, we merely do not receive the signal we are waiting for within the provided timeout. Let's bump the timeout by a factor of ten. With that change I have not been able to reproduce the failure in 150+ iterations. I am also sneaking in a small simplification to the test_progs test selection logic. Signed-off-by:
Daniel Müller <deso@posteo.net> Signed-off-by:
Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20220727182955.4044988-1-deso@posteo.net
-
Jörn-Thorben Hinz authored
A skeleton generated by bpftool previously contained a return followed by an expression in OBJ_NAME__detach(), which has return type void. This did not hurt, the bpf_object__detach_skeleton() called there returns void itself anyway, but led to a warning when compiling with e.g. -pedantic. Signed-off-by:
Jörn-Thorben Hinz <jthinz@mailbox.tu-berlin.de> Signed-off-by:
Quentin Monnet <quentin@isovalent.com> Link: https://lore.kernel.org/bpf/20220726133203.514087-1-jthinz@mailbox.tu-berlin.de
-
Rongguang Wei authored
Use the ARRAY_SIZE macro and make the code more compact. Signed-off-by:
Rongguang Wei <weirongguang@kylinos.cn> Signed-off-by:
-
Fedor Tokarev authored
vsnprintf returns the number of characters which would have been written if enough space had been available, excluding the terminating null byte. Thus, the return value of 'len_left' means that the last character has been dropped. Signed-off-by:
Fedor Tokarev <ftokarev@gmail.com> Signed-off-by:
Alan Maguire <alan.maguire@oracle.com> Link: https://lore.kernel.org/bpf/20220711211317.GA1143610@laptop
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.20. Major changes: ath11k: * fix WCN9074 to work again * revert rfkill support as it was causing problems
-
William Dean authored
The function alloc_workqueue() in rtw_core_init() can fail, but there is no check of its return value. To fix this bug, its return value should be checked with new error handling code. Fixes: fe101716 ("rtw88: replace tx tasklet with work queue") Reported-by:
Hacash Robot <hacashRobot@santino.com> Signed-off-by:
William Dean <williamsukatube@gmail.com> Reviewed-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220723063756.2956189-1-williamsukatube@163.com
-
Zong-Zhe Yang authored
SER (system error recovery) L1 (level 1) has a step-by-step handshake process with FW. These handshakes still rely on B_AX_HS0ISR_IND_INT_EN. So, even already during recovery, we enable this bit in IMR. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
Update to internal tag HALRF_027_00_060. Signed-off-by:
-
Bryan O'Donoghue authored
Add in the ability to easily find the firmware feature bits reported in the get feature exchange without having to compile-in debug prints. root@linaro-alip:~# cat /sys/kernel/debug/ieee80211/phy0/wcn36xx/firmware_feat_caps MCC P2P DOT11AC SLM_SESSIONIZATION DOT11AC_OPMODE SAP32STA TDLS P2P_GO_NOA_DECOUPLE_INIT_SCAN WLANACTIVE_OFFLOAD BEACON_OFFLOAD SCAN_OFFLOAD BCN_MISS_OFFLOAD STA_POWERSAVE STA_ADVANCED_PWRSAVE BCN_FILTER RTT RATECTRL WOW WLAN_ROAM_SCAN_OFFLOAD SPECULATIVE_PS_POLL IBSS_HEARTBEAT_OFFLOAD WLAN_SCAN_OFFLOAD WLAN_PERIODIC_TX_PTRN ADVANCE_TDLS BATCH_SCAN FW_IN_TX_PATH EXTENDED_NSOFFLOAD_SLOT CH_SWITCH_V1 HT40_OBSS_SCAN UPDATE_CHANNEL_LIST WLAN_MCADDR_FLT WLAN_CH144 TDLS_SCAN_COEXISTENCE LINK_LAYER_STATS_MEAS MU_MIMO EXTENDED_SCAN DYNAMIC_WMM_PS MAC_SPOOFED_SCAN FW_STATS WPS_PRBRSP_TMPL BCN_IE_FLT_DELTA Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220727161655.2286867-5-bryan.odonoghue@linaro.org
-
Bryan O'Donoghue authored
Move wcn36xx_get_cap_name() function in main.c into firmware.c as wcn36xx_firmware_get_cap_name(). Reviewed-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Bryan O'Donoghue authored
The naming of the get/set/clear firmware feature capability bits doesn't really follow the established namespace pattern of wcn36xx_logicalblock_do_something(); The feature bits are accessed by smd.c and main.c. It would be nice to display the found feature bits in debugfs. To do so though we should tidy up the namespace a bit. Move the firmware feature exchange API to its own file - firmware.c giving us the opportunity to functionally decompose other firmware related accessors as appropriate in future. Reviewed-by:
-
Bryan O'Donoghue authored
The enum name "place_holder_in_cap_bitmap" is self descriptively asking to be changed to something else. Rename place_holder_in_cap_bitmap to wcn36xx_firmware_feat_caps so that the contents and intent of the enum is obvious. Reviewed-by:
-
David S. Miller authored
Lorenzo Bianconi says: ==================== mtk_eth_soc: introduce xdp multi-frag support Convert mtk_eth_soc driver to xdp_return_frame_bulk APIs. =================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Lorenzo Bianconi authored
Convert mtk_eth_soc driver to xdp_return_frame_bulk APIs. Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Add the capability to map non-linear xdp frames in XDP_TX and ndo_xdp_xmit callback. Signed-off-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to add xdp multi-frag support to mtk_eth_soc driver Signed-off-by:
-
David S. Miller authored
Andrea Mayer says: ==================== seg6: add support for SRv6 Headend Reduced This patchset adds support for SRv6 Headend behavior with Reduced Encapsulation. It introduces the H.Encaps.Red and H.L2Encaps.Red versions of the SRv6 H.Encaps and H.L2Encaps behaviors, according to RFC 8986 [1]. In details, the patchset is made of: - patch 1/4: add support for SRv6 H.Encaps.Red behavior; - Patch 2/4: add support for SRv6 H.L2Encaps.Red behavior; - patch 2/4: add selftest for SRv6 H.Encaps.Red behavior; - patch 3/4: add selftest for SRv6 H.L2Encaps.Red behavior. The corresponding iproute2 patch for supporting SRv6 H.Encaps.Red and H.L2Encaps.Red behaviors is provided in a separated patchset. [1] - https://datatracker.ietf.org/doc/html/rfc8986 V4 -> v5: - Fix skb checksum for SRH Reduced encapsulation/insertion; - Improve selftests by: i) adding a random suffix to network namespaces; ii) creating net devices directly into network namespaces; iii) using trap EXIT command to properly clean up selftest networks. Thanks to Paolo Abeni. v3 -> v4: - Add selftests to the Makefile, thanks to Jakub Kicinski. v2 -> v3: - Keep SRH when HMAC TLV is present; - Split the support for H.Encaps.Red and H.L2Encaps.Red behaviors in two patches (respectively, patch 1/4 and patch 2/4); - Add selftests for SRv6 H.Encaps.Red and H.L2Encaps.Red. v1 -> v2: - Fixed sparse warnings; - memset now uses sizeof() instead of hardcoded value; - Removed EXPORT_SYMBOL_GPL. ==================== Signed-off-by:
-
Andrea Mayer authored
This selftest is designed for testing the H.L2Encaps.Red behavior. It instantiates a virtual network composed of several nodes: hosts and SRv6 routers. Each node is realized using a network namespace that is properly interconnected to others through veth pairs. The test considers SRv6 routers implementing a L2 VPN leveraged by hosts for communicating with each other. Such routers make use of the SRv6 H.L2Encaps.Red behavior for applying SRv6 policies to L2 traffic coming from hosts. The correct execution of the behavior is verified through reachability tests carried out between hosts belonging to the same VPN. Signed-off-by:
Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by:
-
Andrea Mayer authored
This selftest is designed for testing the H.Encaps.Red behavior. It instantiates a virtual network composed of several nodes: hosts and SRv6 routers. Each node is realized using a network namespace that is properly interconnected to others through veth pairs. The test considers SRv6 routers implementing L3 VPNs leveraged by hosts for communicating with each other. Such routers make use of the SRv6 H.Encaps.Red behavior for applying SRv6 policies to L3 traffic coming from hosts. The correct execution of the behavior is verified through reachability tests carried out between hosts belonging to the same VPN. Signed-off-by:
-
Andrea Mayer authored
The SRv6 H.L2Encaps.Red behavior described in [1] is an optimization of the SRv6 H.L2Encaps behavior [2]. H.L2Encaps.Red reduces the length of the SRH by excluding the first segment (SID) in the SRH of the pushed IPv6 header. The first SID is only placed in the IPv6 Destination Address field of the pushed IPv6 header. When the SRv6 Policy only contains one SID the SRH is omitted, unless there is an HMAC TLV to be carried. [1] - https://datatracker.ietf.org/doc/html/rfc8986#section-5.4 [2] - https://datatracker.ietf.org/doc/html/rfc8986#section-5.3Signed-off-by:
Anton Makarov <anton.makarov11235@gmail.com> Signed-off-by:
-
Andrea Mayer authored
The SRv6 H.Encaps.Red behavior described in [1] is an optimization of the SRv6 H.Encaps behavior [2]. H.Encaps.Red reduces the length of the SRH by excluding the first segment (SID) in the SRH of the pushed IPv6 header. The first SID is only placed in the IPv6 Destination Address field of the pushed IPv6 header. When the SRv6 Policy only contains one SID the SRH is omitted, unless there is an HMAC TLV to be carried. [1] - https://datatracker.ietf.org/doc/html/rfc8986#section-5.2 [2] - https://datatracker.ietf.org/doc/html/rfc8986#section-5.1Signed-off-by:
-
