Critical bugfixes for the VMI-Timer code.

1) Do not setup a one shot alarm if we are keeping the periodic alarm
   armed.  Additionally, since the periodic alarm can be run at a lower rate
   than HZ, let's fixup the guard to the no-idle-hz mode appropriately.  This
   fixes the bug where the no-idle-hz mode might have a higher interrupt rate
   than the non-idle case.

2) The interrupt handler can no longer adjust xtime due to nested lock
   acquisition.  Drop this.  We don't need to check for wallclock time at
   every tick, it can be done in userspace instead.

3) Add a bypass to disable noidle operation.  This is useful as a last
   minute workaround, or testing measure.

4) The code to skip the IO_APIC timer testing (no_timer_check) should be
   conditional on IO_APIC, not SMP, since UP kernels can have this configured
   in as well.
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently we do not check for vma flags if sys_move_pages is called to move
individual pages.  If sys_migrate_pages is called to move pages then we
check for vm_flags that indicate a non migratable vma but that still
includes VM_LOCKED and we can migrate mlocked pages.

Extract the vma_migratable check from mm/mempolicy.c, fix it and put it
into migrate.h so that is can be used from both locations.

Problem was spotted by Lee Schermerhorn
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently sm501fb_crtsrc_store() won't allow the routing to be changed via
echos from userspace in to the sysfs file.  The reason for this is that the
strnicmp() for both heads uses a sizeof() for the string length, which ends
up being strlen() + 1 (\0 in the normal case, but the echo gives a newline,
which is where the issue occurs), this then causes a mismatch and
subsequently bails with the -EINVAL.

In addition to this, the hardcoded lengths were then used for the store
length that was returned, which ended up being erroneous and resulting in a
write error.  There's also no point in returning anything but the full
length since it will -EINVAL out on a mismatch well before then anyways.

sizeof("string") is great for making sure you have space in your buffer,
but rather less so for string comparisons :-)
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove the SMT-nice feature which idles sibling cpus on SMT cpus to
facilitiate nice working properly where cpu power is shared.  The idling of
cpus in the presence of runnable tasks is considered too fragile, easy to
break with outside code, and the complexity of managing this system if an
architecture comes along with many logical cores sharing cpu power will be
unworkable.

Remove the associated per_cpu_gain variable in sched_domains used only by
this code.

Also:

  The reason is that with dynticks enabled, this code breaks without yet
  further tweaks so dynticks brought on the rapid demise of this code.  So
  either we tweak this code or kill it off entirely.  It was Ingo's preference
  to kill it off.  Either way this needs to happen for 2.6.21 since dynticks
  has gone in.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

shmem's super_operations were missed from the recent const-ification;
and simple_fill_super()'s, which can share with get_sb_pseudo()'s.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since wext is being replaced as fast as we can (it'll probably stick around
for legacy drivers though) and the wext/netlink stuff was never really
used, this schedules it for removal.

The removal schedule is tight but there are no users of the code, the main
user of the wext user interface are the wireless-tools, they only have an
alpha version using the netlink interface and even that is incomplete.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove remaining references to saved registers now that
uart_handle_sysrq_char() does not want them.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The gpio_keys driver is wrongly ARM-specific; it can't build on
other platforms with GPIO suport.  This fixes that problem.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Nizette <ben.nizette@iinet.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.

So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing.  Currently that's a bunch of
ARMs, and AVR32; more are on the way.

It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix soft lockup with iSeries viocd driver, caused by eventually calling
end_that_request_first() with nr_bytes 0.

Some versions of hald do an SG_IO ioctl on the viocd device which becomes a
request with hard_nr_sectors and hard_cur_sectors set to zero.  Passing zero
as the number of sectors to end_request() (which calls
end_that_request_first()) causes an infinite loop when the bio is being freed.

This patch makes sure that the zero is never passed.  It only requires some
number larger the the request size the terminate the loop.

The lockup is triggered by hald, interrogating the device.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The writing on the wall seem to be that the parport stack is orphaned,
rather than maintained by four folk ...  and having a webpage that says the
latest patches are based on a 2.5 kernel.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

  - ecryptfs_write_inode_size_to_metadata() error code was ignored.
  - i_op->setxattr() must be supported by lower fs because used below.
Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For devices that do not support msi-x we only support 1 interrupt.  Therefore
we can disable that one interrupt by disabling the msi capability itself.  If
we leave the intx interrupts disabled while we have the msi capability
disabled no interrupts should be delivered from that device.

Devices with just the minimal msi support (and thus hitting this code path)
include things like the intel e1000 nic, so it looks like is going to be a
fairly common case and thus important to get right.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

enable/disable_msi_mode have several side effects which keeps them from being
generally useful.  So this patch replaces them with with two much more
targeted functions: msi_set_enable and msix_set_enable.

This patch makes pci_dev->msi_enabled and pci_dev->msix_enabled the definitive
way to test if linux has enabled the msi capability, and has the appropriate
msi data structures set up.

This patch ensures that while writing the msi messages in save/restore and
during device initialization we have the msi capability disabled so we don't
get into races.  The pci spec requires that we do not have the msi capability
enabled and the msi messages unmasked while we write the messages.  Completely
disabling the capability is overkill but it is easy :)

Care has been taken so we never have both a msi capability and intx enabled
simultaneously.  We haven't run into a problem yet but better safe then sorry.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled.  Currently the code has been
calling disable_msi_mode to try and achieve that.  However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.

Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.

pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit.  A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering.  So the call
in pci_disable_device to disable msi capabilities was redundant.

quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A -mm patch caused:

In file included from drivers/pci/quirks.c:532:
include/asm/io_apic.h:61: error: "MAX_IO_APICS" undeclared here (not in a function)

So let's include the needed header.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In http://bugzilla.kernel.org/show_bug.cgi?id=8065, Shen points out that the
cyclades driver forget to return closing_wait to userspace.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Shen <shanlu@cs.uiuc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: make legacy IDE VLB modules check for the "probe" kernel params (v2)
  ide: remove some obsoleted kernel params (v2)
  ide/pci/delkin_cb.c: pci_module_init to pci_register_driver
  scc_pata: bugfix for checking DMA IRQ status
  ide: remove a ton of pointless #undef REALLY_SLOW_IO
  siimage: DRAC4 note
  adjust legacy IDE resource setting (v2)
  ide: fix pmac breakage
  ide-cs: Update device table
  ide: ide_get_best_pio_mode() returns incorrect IORDY setting (take 2)
  piix/slc90e66: more tuneproc() fixing (take 2)
  ide: fix drive side 80c cable check, take 2
  cmd64x: fix PIO mode setup (take 3)
  alim15x3: fix PIO mode setup

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] pata_jmicron: build fix

* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (5260): Cx88-blackbird: allow usage of both 376836 and 262144 sized firmware images
  V4L/DVB (5366): Pvrusb2: Fix compilation warning for amd64 builds (use %zu instead of %u)

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [VLAN]: Avoid a 4-order allocation.
  [HDLC] Fix dev->header_cache_update having a random value.
  [NetLabel]: Verify sensitivity level has a valid CIPSO mapping
  [PPPOE]: Key connections properly on local device.
  [AF_UNIX]: Test against sk_max_ack_backlog properly.
  [NET]: Fix bugs in "Whether sock accept queue is full" checking

* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
  [ARM] Acorn: move the i2c bus driver into drivers/i2c
  [ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
  [ARM] ARM FAS216: don't modify scsi_cmnd request_bufflen
  [ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
  [ARM] rtc-pcf8583: correct month and year offsets
  [ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
  [ARM] EBSA110: Work around build errors
  [ARM] 4241/1: Define mb() as compiler barrier on a uniprocessor system
  [ARM] 4239/1: S3C24XX: Update kconfig entries for PM
  [ARM] 4238/1: S3C24XX: docs: update suspend and resume
  [ARM] 4237/2: oprofile: Always allow backtraces on ARM
  [ARM] Yet more asm/apm-emulation.h stuff
  ARM: OMAP: Add missing get_irqnr_preamble and arch_ret_to_user for omap2
  ARM: OMAP: Use linux/delay.h not asm/delay.h
  ARM: OMAP: Remove obsolete alsa typedefs
  ARM: OMAP: omap1510->15xx conversions needed for sx1
  ARM: OMAP: Add missing includes to board-nokia770
  ARM: OMAP: Workqueue changes for board-h4.c
  ARM: OMAP: dmtimer.c omap1 register fix
  ARM: OMAP: board-nokia770: correct lcd name
  ...

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] MTX1: clear PCI errors
  [MIPS] MTX1: add idsel cardbus ressources
  [MIPS] MTX1: remove unneeded settings
  [MIPS] dma_sync_sg_for_cpu is a no-op except for non-coherent R10000s.
  [MIPS] Cobalt: update reserved resources
  [MIPS] SN: PCI fixup needs to include <irq.h>.
  [MIPS] DMA: Fix a bunch of warnings due to missing inline keywords.
  [MIPS] RM: It should be #ifdef CONFIG_FOO not #if CONFIG_FOO ...
  [MIPS] Fix and cleanup the mess that a dozen prom_printf variants are.
  [MIPS] DEC: Remove redeclarations of mips_machgroup and mips_machtype.
  [MIPS] No need to write c0_compare in plat_timer_setup
  [MIPS] Convert to RTC-class ds1742 driver
  [MIPS] Oprofile: Add missing break statements.
  [MIPS] jmr3927: build fix
  [MIPS] SNI: Fix mc146818_decode_year
  [MIPS] Replace sys32_timer_create with the generic compat_sys_timer_create.
  [MIPS] Replace sys32_socketcall with the generic compat_sys_socketcall.
  [MIPS] N32 waitid is the same as o32.

Move the Acorn IOC/IOMD I2C bus driver from drivers/i2c, strip
out the reminants of the platform specific parts of the old
PCF8583 RTC code, and remove the old obsolete PCF8583 driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

An off-by-one bug meant we were always trying to map one too many
scatterlist entries.  This was mostly harmless prior to the checks
going in to consistent_sync(), but now causes the kernel to BUG.

Also, powertec.c was missing an assignment to info->ec.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

SCSI doesn't want drivers to modify request_bufflen, so keep a
driver-private copy of this in the scsi_pointer structure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Replace the I2C bus address, as per drivers/acorn/char/pcf8583.c.

Also, since this driver also contains Acorn RiscPC specific code
for obtaining the current year from the SRAM (and updating the
platform specific checksum when writing new data back) this is
NOT a platform independent driver.

Document it as such, and update the dependencies to reflect this
fact.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

No, today is not 4th April 3907, it's 4th March 2007.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Both BCD_TO_BIN(x) and BIN_TO_BCD(x) have an unexpected side-effect -
not only do they return the value as expected, they _modify_ their
argument in the process.

Let's play it safe and avoid these macros.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch clears PCI errors after showing more debug informations.
Signed-off-by: Florian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Adds cardbus ressources for MTX1 boards which have a PCMCIA controller.
Signed-off-by: Florian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch removes unnecessary settings at setup time.
Signed-off-by: Florian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch has removed unused timer resource.
Moreover, the name of reserved resources ware changed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

early_printk is a so much saner thing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

If R4k counter was used for hpt_timer and interrupt source,
c0_hpt_timer_init() initializes the c0_compare register.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>