- 05 Jan, 2018 19 commits
-
-
Arnd Bergmann authored
Merge tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt Pull "Amlogic 64-bit DT updates for v4.16, round 2" from Kevin Hilman: This adds a few more basics (clock, pinctrl, PWM, reset) for the new AXG family of Amlogic SoCs. * tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: arm64: dts: meson-axg: add new reset DT node ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC ARM64: dts: meson-axg: add pinctrl DT info for Meson-AXG SoC documentation: Add compatibles for Amlogic Meson AXG pin controllers arm64: dts: meson-axg: add clock DT info for Meson AXG SoC
-
Arnd Bergmann authored
Merge tag 'qcom-dts-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt Pull "Qualcomm Device Tree Changes for v4.16" from Andy Gross: * Add uSD slot nodes on msm8974-FP2 board * tag 'qcom-dts-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux: ARM: dts: msm8974-FP2: Add uSD slot nodes
-
Arnd Bergmann authored
Merge tag 'qcom-arm64-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt Pull "Qualcomm ARM64 Updates for v4.16" from Andy Gross: * Assorted cleanups for msm8916 * Fix IPC references for smsm * tag 'qcom-arm64-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux: arm64: dts: qcom: msm8916-pins: keep cdc_dmic pins in suspend mode arm64: dts: qcom: msm8916-pins: move sdhc2 cd node with its siblings arm64: dts: qcom: msm8916: normalize I2C and SPI nodes arm64: dts: qcom: msm8916: drop unused board-specific nodes arm64: dts: qcom: msm8916-pins: remove assignments to bias-disable arm64: dts: qcom: pm8916: fix wcd_codec indentation arm64: dts: msm8916: Correct ipc references for smsm arm64: dts: msm8916: Add missing #phy-cells
-
Linus Walleij authored
The EB MP board probably has a character LCD but the board manual does not really state which IRQ it has assigned to this device. The invalid assignment was a mistake by me during submission of the DTSI where I was looking for the reference, didn't find it and didn't fill it in. Delete this for now: it can probably be fixed but that requires access to the actual board for some trial-and-error experiments. Reported-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Olof Johansson <olof@lixom.net>
-
Olof Johansson authored
Merge tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt DT for 4.16 - New boards: - Axentia Nattis with Natte power - sama5d2 PTC ek - Document and use extended TCB bindings * tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits) ARM: dts: at91: sama5d2_ptc_ek: use TCB0 as timers ARM: dts: at91: sama5d27_som1_ek: use TCB0 as timers ARM: dts: at91: sama5d2 Xplained: use TCB0 as timers ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices ARM: dts: at91: vinco: use TCB2 as timers ARM: dts: at91: ma5d4: use TCB2 as timers ARM: dts: at91: sama5d4 Xplained: use TCB2 as timers ARM: dts: at91: sama5d4ek: use TCB2 as timers ARM: dts: at91: sama5d4: Add TCB2 ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices ARM: dts: at91: linea/tse850-3: use TCB0 as timers ARM: dts: at91: sama5d3xek_cmp: use TCB0 as timers ARM: dts: at91: kizbox2: use TCB0 as timers ARM: dts: at91: sama5d3 Xplained: use TCB0 as timers ARM: dts: at91: sama5d3xek: use TCB0 as timers ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices ARM: dts: at91: kizboxmini: use TCB0 as timers ARM: dts: at91: cosino: use TCB0 as timers ARM: dts: at91: acme/g25: use TCB0 as timers ARM: dts: at91: at91sam9x5cm: use TCB0 as timers ... Signed-off-by:
-
Olof Johansson authored
Merge tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt UniPhier ARM64 SoC DT updates for v4.16 - clean up gpios properties by macro - add GPIO hog for PXs3 reference node - add has-transaction-translator property to generic-ehci nodes - enable more serial ports for PXs3 reference node * tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier: arm64: dts: uniphier: enable more serial ports for PXs3 ref board arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11 arm64: dts: uniphier: add GPIO hog definition for PXs3 arm64: dts: uniphier: use macros in dt-bindings header Signed-off-by:
-
Olof Johansson authored
Merge tag 'uniphier-dt-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt UniPhier ARM SoC DT updates for v4.16 - clean up gpios properties by macro - add efuse nodes - add has-transaction-translator property to generic-ehci nodes * tag 'uniphier-dt-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier: ARM: dts: uniphier: add has-transaction-translator property to usb node for LD4, sLD8 and Pro4 ARM: dts: uniphier: add efuse node for UniPhier 32bit SoC ARM: dts: uniphier: use macros in dt-bindings header Signed-off-by:
-
Olof Johansson authored
Merge tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt Allwinner DT64 changes for 4.16 There are two important changes in this round. The first removes the redundant pinctrl setting for the MMC card detect GPIO. We are moving to strict pinctrl/GPIO exclusion, i.e. GPIO usage will block other pin muxing usage, and vice versa. The usage of pinmux for guarding GPIO pins in the device tree prevents us from doing so. This is part of an ongoing effort to clean up the existing device trees. The other important change enables the PMIC on the Orangepi Win. The PMIC provides power to most of the external onboard peripherals. Enabling it will allow us to enable Ethernet or WiFi support later on. The remaining changes in this round enable some peripheral, such as Ethernet, an external WiFi chip, or LEDs. * tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: arm64: dts: allwinner: a64: bananapi-m64: Add LED device node arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi arm64: dts: allwinner: h5: NanoPi NEO Plus2 : add EMAC support arm64: dts: allwinner: H5: remove redundant MMC0 card detect pin arm64: allwinner: a64: Enable AXP803 for Orangepi Win arm64: dts: orange-pi-zero-plus2: enable AP6212a WiFi/BT combo Signed-off-by:
-
Olof Johansson authored
Merge tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt Allwinner DT changes for 4.16 A random assortment of improvements. GPIO device nodes are added for the AXP813/AXP818 PMICs, meaning we can finally use the GPIO pins on the PMICs. The LDOs on the GPIO pins can also be properly muxed and guarded. EMAC Ethernet support is enabled for more H3 boards, and also for the A83T, following the return of the bindings in 4.15, after a last minute revert in 4.13. This will make the H3/A83T boards much more useful in headless applications. Two new boards are introduced. The Orange Pi R1 is a small board with two Ethernet interfaces (one EMAC-based and one USB-based) and a WiFi chip. This board is fully supported, with the exception of TV-out on the expansion header, which will not be enabled by default. The WiFi chip (RTL8189FTV) requires an out-of-tree driver. The Libre Computer Board ALL-H3-CC H3 version is a newcomer to the Allwinner SBC space, which was mostly represented by a bunch of fruit-Pis. It is mostly supported, with the exception of HDMI and camera sensor interface, which have not been implemented yet. Two minor patches enable the audio codec on the A13 Olinuxino, and HDMI output on the pcDuino3 Nano. * tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: ARM: dts: sun8i: h3: nanopi-m1-plus: fix missing ethernet 0 in aliases ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Nanopi M1 ARM: dts: sun7i: Enable HDMI on pcDuino3 Nano ARM: dts: sun8i: a83t: Add I2C device nodes and pinmux settings ARM: dts: sun8i: a83t: Add I2S controller device nodes ARM: dts: sun8i-h3: Remove allwinner,leds-active-low for non internal PHY ARM: dts: sun8i: a83t: Enable Ethernet on two boards ARM: dts: sun8i: a83t: add dwmac-sun8i device node ARM: dts: sun8i: h3: enable USB OTG for NanoPi Neo board ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver. ARM: dtsi: axp81x: set pinmux for GPIO0/1 when used as LDOs ARM: dtsi: axp81x: add GPIO DT node ARM: dts: sun8i: add support for Orange Pi R1 ARM: dts: sunxi: Add codec for A13 Olinuxino Signed-off-by:
-
Olof Johansson authored
Merge tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt ARM: Keystone DTS update for 4.16 - Enable GPIO bank2 for K2L - Enable QSPI for K2G & K2G-EVM - Enable UART1/2 for K2G & K2G-EVM - Enable peripherals for K2G-ICE - Fix C1 and C2 DTS warnings * tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: ARM: dts: keystone-k2l-clocks: Add missing unit name to clock nodes that have regs ARM: dts: keystone-k2e-clocks: Add missing unit name to clock nodes that have regs ARM: dts: keystone-hk-clocks: Add missing unit name to clock nodes that have regs ARM: dts: keystone-clocks: Add missing unit name to clock nodes that have regs ARM: dts: keystone: Add missing unit name to interrupt controller ARM: dts: keystone: Get rid of usage of skeleton.dtsi ARM: dts: keystone*: Use a single soc0 instance ARM: dts: keystone*: Standardize license with SPDX tag ARM: dts: k2g-evm: Enable UART 2 ARM: dts: k2g: Add UART 1 and 2 instances ARM: dts: keystone: Add generic compatible string for I2C EEPROM ARM: dts: keystone-k2g-ice: Add DT nodes for few peripherals ARM: dts: keystone-k2g-evm: Add QSPI DT node. ARM: dts: keystone-k2g: Move ti,non-removable property to board dts ARM: dts: keystone-k2g-evm: Fix botched up merge ARM: dts: keystone-k2g: Add QSPI DT entry ARM: dts: keystone-k2l: Add the second gpio bank node Signed-off-by:
-
Olof Johansson authored
Merge tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt Second set of device tree changes for omaps for v4.16 merge window This branch mostly configures more hardware support: - Clean-up dts files to remove leading 0x and 0s from binding notation to remove more dtc compiler warnings - A series of am437x updates for backlight, to fix inverted pad pull macro, and to configure power management related OPPs - Configure n950 and droid 4 command mode LCD panels - Updates to pandora and gta04 LCD panels - Add support for am574x-idk - A series of changes to configure more dra7 related PCIe features - A series of fixes for am335x-boneblue for WLAN, UARTs and CAN configuration - A series of changes to configure dra7 OPPs and VDD supplies * tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits) Revert "ARM: dts: dra7: Add properties to enable PCIe x2 lane mode" ARM: dts: am572x-idk: Add cpu0 vdd supply ARM: dts: am571x-idk: Add cpu0 vdd supply ARM: dts: dra72-evm-tps65917: Add cpu0 vdd supply ARM: dts: dra7-evm: Add cpu0 vdd supply ARM: dts: am57xx-beagle-x15-common: Add cpu0 vdd supply ARM: dts: dra7: Enable 1.5 GHz operation for the CPU ARM: dts: dra7: Add MPU OPP supply node ARM: dts: dra7: Add vbb-supply to cpu and additional voltages ARM: dts: am335x-boneblue: enable can ARM: dts: am335x-boneblue: enable usarts ARM: dts: am335x-boneblue: fix wl1835 IRQ pin ARM: dts: dra7: Remove deprecated PCI compatible string ARM: dts: dra76-evm: Enable x2 PCIe lanes ARM: dts: DRA72x: Use PCIe compatible specific to dra72 ARM: dts: DRA74x: Use PCIe compatible specific to dra74 ARM: dts: dra7: Add properties to enable PCIe x2 lane mode ARM: dts: am57xx: Add support for am574x-idk ARM: dts: am43x-epos-evm: Hook dcdc2 as the cpu0-supply ARM: dts: am437x-idk-evm: Disable OPP50 for MPU ... Signed-off-by:
-
git://git.infradead.org/linux-mvebuOlof Johansson authored
mvebu dt64 for 4.16 (part 1) Add the NAND support on the Marvell 8040-DB board Add the thermal support for Martvell A7K/A8K Socs Add nodes allowing cpufreq support on Aramda 3700 SoCs * tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu: ARM64: dts: marvell: Add thermal support for A7K/A8K arm64: dts: marvell: armada-37xx: add nodes allowing cpufreq support arm64: dts: marvell: add NAND support on the 8040-DB board Signed-off-by:
-
git://git.infradead.org/linux-mvebuOlof Johansson authored
mvebu dt for 4.16 (part 1) Fix potential dtc warnings on kirkwoods files Declare a new pin (RB) usbale for NAND controller on Armada 38x * tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu: arm: kirkwood: dts: Use lower case for bindings notation ARM: dts: armada-38x: Add NAND RB pinctrl information Signed-off-by:
-
Olof Johansson authored
Merge tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt Second Round of Renesas ARM Based SoC DT Updates for v4.16 * r8a7745 (RZ/G1E) SoC - Enable SMP Fabrizio Castro says "Add DT node for the Advanced Power Management Unit (APMU), add the second CPU core, and use "renesas,apmu" as "enable-method"." * r8a7743 (RZ/G1M) SoC - Add node for thermal sensor module with thermal-zone support * r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs - Add: + Renesas Core Match Timer (CMT) support + Renesas Timer Pulse Unit PWM Controller (TPU) support + Renesas PWM Timer Controller (PWM) support * r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms - Add sound support * r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs - Allow DTBs of boards of these SoCs to build without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05 + Move nodes which have no reg property out of bus, they don't belong there + Also sort sub-nodes of root node to allow for easier maintenance * r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs - Correct critical CPU temperature Chris Paterson says "The current R-Car Gen2 device trees define the CPU critical temperature as 115°C. The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal sensor has an accuracy of ±5°C and there can be a temperature difference of 1 or 2 degrees between Tjmax and the thermal sensor due to the location of the latter. This means that 95°C is a safer value to use. This value should also apply to r8a7792 but thermal sensor support has not been added yet." * r8a7740 (R-Mobile A1) SoC - Correct TPU register block size Geert Uytterhoven says "The Timer Pulse Unit has registers that lie outside the declared register block. Enlarge the register block size to fix this. This was probably based on the old platform code, which also assumed a register block size of 0x100." * tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (37 commits) ARM: dts: r8a7745: Add missing clock for secondary CA7 CPU core ARM: dts: iwg22d-sodimm: Sound DMA support via DVC on DTS ARM: dts: iwg22d-sodimm: Sound DMA support via SRC on DTS ARM: dts: iwg22d-sodimm: Sound DMA support via BUSIF on DTS ARM: dts: iwg22d-sodimm: Sound DMA support on DTS ARM: dts: iwg22d-sodimm: Sound PIO support ARM: dts: iwg22d-sodimm: Enable SGTL5000 audio codec ARM: dts: r8a7745: Add sound support ARM: dts: r8a7745: Add audio DMAC support ARM: dts: r8a7745: Add audio clocks ARM: dts: r8a7740: Correct TPU register block size ARM: dts: r8a7743: move timer and thermal-zones nodes out of bus ARM: dts: r8a7743: sort root sub-nodes alphabetically ARM: dts: iwg20d-q7-common: Sound DMA support via DVC on DTS ARM: dts: iwg20d-q7-common: Sound DMA support via SRC on DTS ARM: dts: iwg20d-q7-common: Sound DMA support via BUSIF on DTS ARM: dts: iwg20d-q7-common: Sound DMA support on DTS ARM: dts: iwg20d-q7-common: Sound PIO support ARM: dts: iwg20d-q7-common: Enable SGTL5000 audio codec ARM: dts: r8a7792: move timer node out of bus ... Signed-off-by:
-
Olof Johansson authored
Merge tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt Second Round of Renesas ARM64 Based SoC DT Updates for v4.16 * Add usb3_phy node to r8a7795 (R-Car H3) and r8a7796 (R-Car M3-W) SoCs, and enable usb3_peri0 on salvator boards * Allow DTBs of boards of r8a7795 (R-Car H3) and r8a7796 SoCs to build without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05 - Move nodes which have no reg property out of bus, they don't belong there - Add reg properties to dummy pciec[01] nodes - Also sort sub-nodes of root node to allow for easier maintenance * Add Add EthernetAVB PHY reset to r8a7795 (R-Car H3) and r8a7796 SoCs boards. Geert Uytterhoeven says "... add properties to describe the EthernetAVB PHY reset topology to the common Salvator-X/XS and ULCB DTS files, which solves two issues: 1. On Salvator-XS, the enable pin of the regulator providing PHY power is connected to PRESETn, and PSCI powers down the SoC during system suspend. Hence a PHY reset is needed to restore network functionality after system resume. 2. Linux should not rely on the boot loader having reset the PHY, but should reset the PHY during driver probe." * tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: arm64: dts: renesas: salvator-common: enable usb3_peri0 arm64: dts: renesas: salvator-common: enable usb3_phy0 node arm64: dts: renesas: r8a7796: add usb3_phy node arm64: dts: renesas: r8a7795: add usb3_phy node arm64: dts: renesas: r8a7796: add reg properties to pciec[01] nodes arm64: dts: renesas: r8a7796: move nodes which have no reg property out of bus arm64: dts: renesas: r8a7796: sort subnodes of root node alphabetically arm64: dts: renesas: r8a7795: sort subnodes of root node alphabetically arm64: dts: renesas: ulcb: Add EthernetAVB PHY reset arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset arm64: dts: renesas: r8a7795: Move nodes which have no reg property out of bus Signed-off-by:
-
Olof Johansson authored
Merge tag 'actions-arm64-dt-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt Actions Semi arm64 based SoC DT for v4.16 This adds S700 SoC and CubieBoard7. * tag 'actions-arm64-dt-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions: arm64: dts: actions: Add S700 and CubieBoard7 dt-bindings: power: Add Actions Semi S700 SPS dt-bindings: arm: actions: Add S700 and CubieBoard7 Signed-off-by:
-
Olof Johansson authored
Merge tag 'actions-arm-dt-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt Actions Semi arm based SoC DT for v4.16 This adds a DT for the Allo.com Sparky SBC. * tag 'actions-arm-dt-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions: arm: dts: owl-s500: Add Sparky dt-bindings: arm: actions: Add Sparky dt-bindings: Add vendor prefix for Allo.com Signed-off-by:
-
git://github.com/hisilicon/linux-hisiOlof Johansson authored
ARM64: DT: Hisilicon SoC DT updates for 4.16 - Add SD card support for the hi3798cv200-poplar board - Replace the PMU node with exact match for the hi3660 SoC - Add cpu capacity-dmips-mhz information for the hi3660 SoC * tag 'hisi-arm64-dt-for-4.16-v2' of git://github.com/hisilicon/linux-hisi: arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information arm64: dts: hi3660: improve pmu description arm64: dts: hi3798cv200: add SD card support Signed-off-by:
-
http://github.com/Broadcom/stblinuxOlof Johansson authored
This pull request contains Broadcom ARM-based SoCs Device Tree changes for 4.16, please pull the following: - Stefan updates the BCM283x DTS to make consistent use of the existing GPIO defines for the polarity specifier * tag 'arm-soc/for-4.16/devicetree' of http://github.com/Broadcom/stblinux: ARM: dts: bcm283x: Use GPIO polarity defines consistently Signed-off-by:
-
- 04 Jan, 2018 4 commits
-
-
Arnd Bergmann authored
The added header inclusion broke the 'allmodconfig' build in arm-soc, presumably since the file is added in a different tree: In file included from arch/arm64/boot/dts/sprd/sp9860g-1h10.dts:11:0: arch/arm64/boot/dts/sprd/sc9860.dtsi:10:10: fatal error: dt-bindings/clock/sprd,sc9860-clk.h: No such file or directory It turns out we don't actually need to include it at all, so I'm removing the line again to fix the build. Fixes: 22f37a24 ("arm64: dts: add clocks for SC9860") Signed-off-by:
-
Arnd Bergmann authored
Merge tag 'gemini-dts-update-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt Pull "A second set of Gemini DTS updates for v4.16" from Linus Walleij: - Use Open Drain flags properly for emulated I2C - Add the PCI bus to WBD111 and WBD222 - Enable the TVE and panel on DIR-685; the panel driver and bindings have been merged into the DRI subsystem. * tag 'gemini-dts-update-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: ARM: dts: Add TVE/TVC and ILI9322 panel to DIR-685 ARM: dts: Add PCI to WBD111 and WBD222 ARM: dts: Flags D-Link DIR-685 I2C bus gpios
-
Chunyan Zhang authored
Some clocks on SC9860 are in the same address area with syscon devices, those are what have a property of 'sprd,syscon' which would refer to syscon devices, others would have a reg property indicated their address ranges. Signed-off-by:
Chunyan Zhang <chunyan.zhang@spreadtrum.com> Signed-off-by:
-
Chunyan Zhang authored
Some clocks on SC9860 are in the same address area with syscon devices, the proper syscon node will be quoted under the definitions of those clocks in DT. Signed-off-by:
-
- 01 Jan, 2018 8 commits
-
-
Damien Riegel authored
This node was the only one that didn't have the same set of pins in active and suspend mode. Signed-off-by:
Damien Riegel <damien.riegel@savoirfairelinux.com> Signed-off-by:
Andy Gross <andy.gross@linaro.org>
-
Damien Riegel authored
Nodes relative to the first sdhc node were interlaced with node of the second sdhc. Move sdhc2_cd_pin with its siblings to prevent that. Also rename the grouping node from sdhc2_cd_pin to pmx_sdc2_cd_pin, as "pmx_sdc" is the prefix used by other nodes. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Damien Riegel authored
The QUP core can be used either for I2C or SPI, so the same IP is mapped by a driver or the other. SPI bindings use a leading 0 for the start address and a size of 0x600, I2C bindings don't have the leading 0 and have a size 0x1000. To make them more similar, add the leading 0 to I2C bindings and changes the size to 0x500 for all of them, as this is the actual size of these blocks. Also align the second entry of the clocks array. Signed-off-by:
-
Damien Riegel authored
These nodes reserve and configure some pins as GPIOs. They are not generic pinctrls, they actually belong to board files but they are not used by any other node, so just drop them altogether. Signed-off-by:
-
Damien Riegel authored
Drop assignments to bias-disable as the documentation [1] states that this property doesn't take a value. Other occurrences of this property respect that. [1] Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt Signed-off-by:
-
Damien Riegel authored
Indentation did not respect kernel standards, so fix that for the usual indent with tabs, align with spaces. While at it, remove some empty lines before and after the closing parenthesis of this block. Signed-off-by:
-
Bjorn Andersson authored
SMSM is not symmetrical, the incoming bits from WCNSS are available at index 6, but the outgoing host id for WCNSS is 3. Further more, upstream references the base of APCS (in contrast to downstream), so the register offset of 8 must be included. Fixes: 1fb47e0a ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes") Cc: stable@vger.kernel.org Reported-by:
Ramon Fried <rfried@codeaurora.org> Signed-off-by:
-
Bjorn Andersson authored
Add a missing #phy-cells to the dsi-phy, to silence dtc warning. Cc: Archit Taneja <architt@codeaurora.org> Fixes: 305410ff ("arm64: dts: msm8916: Add display support") Signed-off-by:
Archit Taneja <architt@codeaurora.org> Signed-off-by:
-
- 31 Dec, 2017 9 commits
-
-
Nicolas Ferre authored
Use tcb0 for timers as selected in sama5_defconfig. Signed-off-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com>
-
Alexandre Belloni authored
Use tcb0 for timers as selected in sama5_defconfig. Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Alexandre Belloni authored
Use tcb0 for timers as selected in sama5_defconfig. Tested-by:
-
Alexandre Belloni authored
Add simple-mfd and syscon to the TC blocks to allow to register one of the channels as clocksource properly at boot time and free up the remaining channels for other use. Acked-by:
-
Alexandre Belloni authored
As TCB2 doesn't have any output pins, use it for timers Acked-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by:
-
Alexandre Belloni authored
As TCB2 doesn't have any output pins, use it for timers Cc: Marek Vasut <marex@denx.de> Acked-by:
-
Alexandre Belloni authored
As TCB2 doesn't have any output pins, use for timers. Tested-by:
-
Alexandre Belloni authored
As TCB2 doesn't have any output pins, use it for timers. Acked-by:
-
Alexandre Belloni authored
The third TC block is missing from the dtsi. It has no output pins but can still be used for timers as the IRQ is wired. Acked-by:
-
