Merge "mvebu-fixes-6" from Andrew Lunn:

The previous fix for Armada XP, disabling I/O coherency, broke Armada
375/38x.  Only switch the PL310 to I/O coherent mode if I/O coherency
is enabled.

* tag 'mvebu-fixes-3.19-6' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: don't set the PL310 in I/O coherency mode when I/O coherency is disabled
Signed-off-by: Olof Johansson <olof@lixom.net>

Since commit f2c3c67f (merge commit that adds commit "ARM: mvebu:
completely disable hardware I/O coherency"), we disable I/O coherency
on Armada EBU platforms.

However, we continue to initialize the coherency fabric, because this
coherency fabric is needed on Armada XP for inter-CPU
coherency. Unfortunately, due to this, we also continued to execute
the coherency fabric initialization code for Armada 375/38x, which
switched the PL310 into I/O coherent mode. This has the effect of
disabling the outer cache sync operation: this is needed when I/O
coherency is enabled to work around a PCIe/L2 deadlock. But obviously,
when I/O coherency is disabled, having the outer cache sync operation
is crucial.

Therefore, this commit fixes the armada_375_380_coherency_init() so
that the PL310 is switched to I/O coherent mode only if I/O coherency
is enabled.

Without this fix, all devices using DMA are broken on Armada 375/38x.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.8+

Merge tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes

Merge "Allwinner fixes for 3.19" from Maxime Ripard:

Allwinner fixes for 3.19

A few minor fixes for the 3.19 kernel:
  - The 8250 uart driver now respects the aliases, which pointed out that we
    were using them wrong. Fixed them.
  - The simplefb pipeline that was used on the A10 caused flickering and
    tearing, and rendered it pretty much useless. Added a new simplefb node
    with another pipeline that removes this issue. Note that we need to keep
    the old node because u-boot 2015.01 uses it.
  - Added a fix for the USB phy node on sun4i/sun5i

* tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: sunxi: dt: Fix aliases
  ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
  ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
  ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
Signed-off-by: Olof Johansson <olof@lixom.net>

Commit f77d55a3 ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.

Remove them from the DTSI and add custom ones in the relevant boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Merge tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 3.19, 2nd round" from Shawn Guo:

The i.MX fixes for 3.19, 2nd round:
 - Correct pwm clock assignment in i.MX25 device tree to fix the broken
   pwm support on i.MX25

* tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx25: Fix PWM "per" clocks
Signed-off-by: Olof Johansson <olof@lixom.net>

Without explicit command-line parameters, the Juno UART ends up running
at 57600 baud in the kernel, which is at odds with the 115200 baud used
by the rest of the firmware. Since commit 7914a7c5 now lets us
fix this by specifying default options in stdout-path, do so.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "mvebu/fixes #3" from Andrew Lunn:

mvebu fixes for 3.19. (Part 4)

bus: mvebu-mbus: fix support of MBus window 13

* tag 'mvebu-fixes-3.19-4' of git://git.infradead.org/linux-mvebu:
  bus: mvebu-mbus: fix support of MBus window 13
  ARM: mvebu: completely disable hardware I/O coherency
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Merge "Second Round of Renesas ARM Based SoC Fixes for v3.19" from Simon
Horman:

* Instantiate GIC from C board code in legacy builds on r8a7778 and r8a7779

* tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
  ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
Signed-off-by: Olof Johansson <olof@lixom.net>

Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.

Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Currently PWM functionality is broken on mx25 due to the wrong assignment of the
PWM "per" clock.

According to Documentation/devicetree/bindings/clock/imx25-clock.txt:
	pwm_ipg_per		52

,so update the pwm "per" to use 'pwm_ipg_per' instead of 'per10' clock.

With this change PWM can work fine on mx25.

Cc: <stable@vger.kernel.org>
Reported-by: Carlos Soto <csotoalonso@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Merge tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge "Urgent omap4 legacy interrupt regression fix for v3.19-rc series" from
Tony Lindgren:

A rather urgent pull request to fix omap4 legacy interrupts.

The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.

Also include is a regression fix for the dra7 dwc3 suspend.

* tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP: Work around hardcoded interrupts
  arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Signed-off-by: Olof Johansson <olof@lixom.net>

On Armada XP, 375 and 38x the MBus window 13 has the remap capability,
like windows 0 to 7. However, the mvebu-mbus driver isn't currently
taking into account this special case, which means that when window 13
is actually used, the remap registers are left to 0, making the device
using this MBus window unavailable.

As a minimal fix for stable, don't use window 13. A full fix will
follow later.

Fixes: fddddb52 ("bus: introduce an Marvell EBU MBus driver")
Cc: <stable@vger.kernel.org> # v3.10+
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Merge " mvebu fixes for 3.19-rc (part #3)" from Andrew Lunn:

mvebu: completely disable hardware I/O coherency

* tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: completely disable hardware I/O coherency
Signed-off-by: Olof Johansson <olof@lixom.net>

The current hardware I/O coherency is known to cause problems with DMA
coherent buffers, as it still requires explicit I/O synchronization
barriers, which is not compatible with the semantics expected by the
Linux DMA coherent buffers API.

So, in order to have enough time to validate a new solution based on
automatic I/O synchronization barriers, this commit disables hardware
I/O coherency entirely. Future patches will re-enable it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Commit 9a1091ef ("irqchip: gic: Support hierarchy irq domain")
changed the GIC driver to use a non-legacy IRQ domain on DT
platforms. This patch assumes that DT-driven systems are getting
all of their interrupts from device tree.

Turns out that OMAP has quite a few hidden gems, and still uses
hardcoded interrupts despite having fairly complete DTs.

This patch attempts to work around these by offering a translation
method that can be called directly from the hwmod code, if present.
The same hack is sprinkled over PRCM and TWL.

It isn't pretty, but it seems to do the job without having to add
more hacks to the interrupt controller code.

Tested on OMAP4 (Panda-ES) and OMAP5 (UEVM5432).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated to fix make randconfig issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'samsung-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung fixes for v3.19" from Kukjin Kim:

Samsung fixes for v3.19
- exynos_defconfig: enable LM90 driver and display panel support
   - HWMON
   - SENSORS_LM90
   - Direct Rendering Manager (DRM)
   - DRM bridge registration and lookup framework
   - Parade ps8622/ps8625 eDP/LVDS bridge
   - NXP ptn3460 eDP/LVDS bridge
   - Exynos Fully Interactive Mobile Display controller (FIMD)
   - Panel registration and lookup framework
   - Simple panels
   - Backlight & LCD device support

- use pmu_system_controller phandle for dp phy
  : DP PHY requires pmu_system_controller to handle PMU reg. now

* tag 'samsung-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: exynos_defconfig: Enable LM90 driver
  ARM: exynos_defconfig: Enable options for display panel support
  arm: dts: Use pmu_system_controller phandle for dp phy
Signed-off-by: Olof Johansson <olof@lixom.net>

Call spin_lock_init() before the spinlocks are used, both in early init
and probe functions preventing a lockdep splat.

I have been observing lockdep complaining [1] during boot on my a80 optimus [2]
when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat,
and has been tested on a few other sunxi platforms without issue.

[1] http://storage.kernelci.org/next/next-20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html
[2] http://kernelci.org/boot/?a80-optimusSigned-off-by: Tyler Baker <tyler.baker@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Merge "Renesas ARM Based SoC Fixes for v3.19" from Simon Horman:

Renesas ARM Based SoC Fixes for v3.19

This pull request is based on the last round of SoC updates for v3.19,
Fourth Round of Renesas ARM Based SoC Updates for v3.19, tagged as
renesas-soc3-for-v3.19, merged into your next/soc branch and included in
v3.19-rc1.

- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

  Set .control_parent for all irqpin instances for sh73a0 SoC when booting
  using legacy C.

- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

  This fixes a long standing problem which has been present since
  the sh73a0 SoC started using the INTC External IRQ pin driver.

  The patch that introduced the problem is 341eb546 ("ARM:
  shmobile: INTC External IRQ pin driver on sh73a0") which was included
  in v3.10.

* tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
  ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The arm-cci driver completes the probe sequence even if the cci node is
marked as disabled. Add a check in the driver to honour the cci status
in the device tree.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes

Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:

First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4

* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
  ARM: at91/dt: sam9263: Add missing clocks to lcdc node
  ARM: at91: sama5d3: dt: correct the sound route
  ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>

rk3288 SoCs have a function to automatically switch between jtag/sdmmc pinmux
settings depending on the card state. This collides with a lot of assumptions.

It only works when using the internal card-detect mechanism and breaks
horribly when using either the normal card-detect via the slot-gpio function
or via any other pin. Also there is of course no link between the mmc and jtag
on the software-side, so the jtag clocks may very well be disabled when the
card is ejected and the soc switches back to the jtag pinmux.

Leaving the switching function enabled did result in mmc timeouts and rcu
stalls thus hanging the system on 3.19-rc1. Therefore disable it in all cases,
as we expect the devicetree to explicitly select either mmc or jtag pinmuxes
anyway.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin into fixes

Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:

Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation

* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
  ARM: dts: berlin: correct BG2Q's SM GPIO location.
  ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
  ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
Signed-off-by: Olof Johansson <olof@lixom.net>

We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge "omap fixes against v3.19-rc1" from Tony Lindgren:

Fixes for omaps mostly to deal with dra7 timer issues
and hypervisor mode. The other fixes are minor fixes for
various boards. The summary of the fixes is:

- Fix real-time counter rate typos for some frequencies
- Fix counter frequency drift for am572x
- Fix booting of secondary CPU in HYP mode
- Fix n900 board name for legacy user space
- Fix cpufreq in omap2plus_defconfig after Kconfig change
- Fix dra7 qspi partitions

And also, let's re-enable smc91x on some n900 boards that
we have sitting in a few test boot systems after the boot
loader dependencies got fixed.

* tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: Revert disabling of smc91x for n900
  ARM: dts: dra7-evm: fix qspi device tree partition size
  ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
  ARM: OMAP2+: Fix n900 board name for legacy user space
  ARM: omap5/dra7xx: Enable booting secondary CPU in HYP mode
  ARM: dra7xx: Fix counter frequency drift for AM572x errata i856
  ARM: omap5/dra7xx: Fix frequency typos
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 3.19" from Shawn Guo:

The i.MX fixes for 3.19:
 - One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
   which causes system hang when accessing SPI1.
 - Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
 - Fix ULPI PHY reset modelling on imx51-babbage board to remove the
   dependency on bootloader for USB3317 ULPI PHY reset.
 - Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
   that HDMI is not working at high resolution on T0 1.0.
 - One incremental fix for CODA960 VPU enabling in device tree to
   correct interrupt order.
 - LS1021A SCFG block works in BE mode, add device tree property
   big-endian to make it right.

* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
  ARM: imx6sx: Set PLL2 as parent of QSPI clocks
  ARM: dts: imx25: Fix the SPI1 clocks
  ARM: clk-imx6q: fix video divider for rev T0 1.0
  ARM: dts: imx6qdl: Fix CODA960 interrupt order
  ARM: ls1021a: dtsi: add 'big-endian' property for scfg node
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Merge "ARM: rockchip: dts fix for 3.19" from Heiko Stübner:

Increase drive-strength to sdmmc pins on rk3288-evb to fix
an issue with the fixed highspeed card detection.

* tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: bump sd card pin drive strength up on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>

As of commit 9a1091ef ("irqchip: gic: Support hierarchy irq
domain."), Marzen legacy hangs during boot with:

   Image Name:   'Linux-3.19.0-rc4'
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3445880 Bytes = 3.3 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Enabling DEBUG_LL does not seem to change the situation, however this
patch by itself fixes this issue and re-enables normal boot.

This issue happens because the IRQ numbers of the GIC are now virtual,
and no longer match the hardcoded hardware IRQ numbers in the platform
board code.

To fix this, instantiate the GIC from platform board code when compiling
a legacy kernel, like is done for the sh73a0, r8a7740 and r8a7778 legacy code.

Follows same style as the r8a7740 legacy GIC fix by Geert Uytterhoeven,
thanks to him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As of commit 9a1091ef ("irqchip: gic: Support hierarchy irq
domain."), Bock-W legacy hangs during boot with:

Unable to handle kernel paging request at virtual address cf86a128
pgd = c0004000
[cf86a128] *pgd=6f80041e(bad)
Internal error: Oops: 8000000d [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc4 #1
Hardware name: bockw
task: cf823b40 ti: cf824000 task.ti: cf824000
PC is at 0xcf86a128
LR is at request_threaded_irq+0xbc/0x124

This happens because the IRQ numbers of the GIC are now virtual, and no
longer match the hardcoded hardware IRQ numbers in the platform board
code.

To fix this, instantiate the GIC from platform board code when compiling
a legacy kernel, like is done for the sh73a0 and r8a7740 legacy code.

Follows same style as the r8a7740 legacy GIC fix by Geert Uytterhoeven,
thanks to him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Whenever Suspend PHY bit is set on DRA7x devices,
USB will not work due to Set EP Configuration command
always failing.

This was only found after a recent commit 2164a476 (usb:
dwc3: set SUSPHY bit for all cores, which will be merged
for v3.19) added a missing *required* step to dwc3
initialization. Synopsys Databook requires that we enable
Suspend PHY bit after initialization but that, unfortunately,
breaks DRA7x.

Note that the same regression was already patched for AM437x.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Appearance: On some SAMA5D4EK boards, after power up, the Eth1 doesn't work.

Reason: The PIOE2 pin is connected to the NAND_Tree# of KSZ8081,
But it outputs LOW during the reset period, which cause the NAND_Tree# enabled.

Add phy_fixup() to disable NAND_Tree by overriding the Operation
Mode Strap Override register(i.e. Register 16h) to clear the NAND_Tree bit.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

atmel_lcdfb needs also uses hclk clock, but AT91SAM9263 doesn't have that
specific clock, so use lcd_clk twice. The same was done in
arch/arm/mach-at91/at91sam9263.c
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The MICBIAS is a supply, should route to MIC while not IN1L.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The second property of reg is the length, so correct it for timer.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

multi_v7_defconfig has it as Y already, so build it in here, too, for
consistency, and therefore build in HWMON as well.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

Many Exynos devices have a display panel. Most of them just have
a simple panel while others have more complex configurations that
requires an embedded DisplayPort (eDP) to LVDS bridges.

This patch enables the following features to be built in the kernel
image to support both setups:

- Direct Rendering Manager (DRM)
- DRM bridge registration and lookup framework
- Parade ps8622/ps8625 eDP/LVDS bridge
- NXP ptn3460 eDP/LVDS bridge
- Exynos Fully Interactive Mobile Display controller (FIMD)
- Panel registration and lookup framework
- Simple panels
- Backlight & LCD device support
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

Pull ARM fixes from Russell King:
 "Three small fixes from over the Christmas period, and wiring up the
  new execveat syscall for ARM"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error
  ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region
  ARM: 8249/1: mm: dump: don't skip regions
  ARM: wire up execveat syscall

Pull x86 fixes from Ingo Molnar:
 "Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix
  with certain odd memory mappings"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, vdso: Use asm volatile in __getcpu
  x86/build: Clean auto-generated processor feature files
  x86: Fix mkcapflags.sh bash-ism
  x86: Fix step size adjustment during initial memory mapping
  x86_64, vdso: Fix the vdso address randomization algorithm

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: group scheduling corner case fix, two deadline scheduler
  fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs
  system fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
  sched/deadline: Avoid double-accounting in case of missed deadlines
  sched/deadline: Fix migration of SCHED_DEADLINE tasks
  sched: Fix odd values in effective_load() calculations
  sched, fanotify: Deal with nested sleeps
  sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation