Add code to support setting jack-detect parameters through quirks and
extend the existing DMI quirk table entries for the Asus T100TA and the
Dell Venue 8 Pro 5830 to enable jack detection.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This fixes the following 3 issues:

1) The sys_vendor match should be for "Dell Inc." not "DellInc.",
   without this fixed the quirk never gets applied
2) DMIC1 is used not DMIC2, this was not a problem sofar because for
   regular BYT boards (rather then BYTCR) we default to DMIC1 and because
   of 1. the quirk was not being applied
3) The Dell Venue 8 5830 Pro only has a single speaker
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use device-properties for setting up the dmic, based on the
BYT_RT5640_MAP() value, instead of using the codec specific
rt5640_dmic_enable() function for this.  This also removes the need
for the BYT_RT5640_DMIC_EN quirk, which was always set together with
a MAP() quirk of DMIC1_MAP or DMIC2_MAP.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: 9958e8afbcad ("ASoC: rt5663: Use the set_jack() instead of the export function")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The patch replaces the export function with the new API set_jack().
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The sdma-pcm does not need any information from omap-dma.h, it only needs
to include the omap-dmaengine.h - for the omap_dma_filter_fn, but that
might not be needed at all as OMAP1 was converted to dma_slave_map, but
I can not test OMAP1.

Add the linux/device.h include as well for devm_kzalloc()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

WARNING: modpost: missing MODULE_LICENSE() in sound/soc/omap/snd-soc-sdma.o
see include/linux/module.h for more information
WARNING: modpost: missing MODULE_LICENSE() in sound/soc/omap/snd-soc-sdma.o
see include/linux/module.h for more information

Add the missing MODULE_LICENSE.

This patch also going to solve:
snd_soc_sdma: Unknown symbol devm_kmalloc (err 0)
snd_soc_sdma: Unknown symbol omap_dma_filter_fn (err 0)
snd_soc_sdma: Unknown symbol snd_dmaengine_pcm_prepare_slave_config (err 0)
snd_soc_sdma: Unknown symbol devm_snd_dmaengine_pcm_register (err 0)
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix the compile error introduced by: "ASoC: Intel: bytcr_rt5640:
Configure PLL1 before using it".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Trivial fix to spelling mistake in dev_err message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

There are only one set of ops on the compressed stream so no need to
reassign the copy callback repeatedly, stop after copy is seen to be
necessary.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds some common helper functions like translating dsp error
to linux error codes and channel mappings etc.

These functions are used in all the following qdsp6 drivers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add DT bindings for ASM (Audio Stream Manager) DSP module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add DT bindings for ADM (Audio Device Manager) DSP module.
This module implements mixer controls to setup the connections between
AFE ports and ASM streams.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add DT bindings for AFE (Audio Frontend) DSP module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add DT bindings for Q6CORE DSP module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds support to APR bus (Asynchronous Packet Router) driver.
APR driver is made as a bus driver so that the apr devices can added removed
more dynamically depending on the state of the services on the dsp.
APR is used for communication between application processor and QDSP to
use services on QDSP like Audio and others.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add dt bindings for Qualcomm APR (Asynchronous Packet Router)
bus driver. This bus is used for communicating with DSP which provides
audio and various other services to cpu.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Removed separate byte count variables for playback and capture.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Added byte count register offset variables to audio_substream_data
structure. Modified dma pointer callback.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Added dma configuration parameters to rtd structure.
Moved dma configuration parameters initialization to
hw_params callback.
Removed hard coding in prepare and trigger callbacks.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

I2S controller on EP93xx seems to have undocumented HW issue. According to
"EP93xx User’s Guide", controller can handle underflow and either transmit
last sample or zeroes in such case until FIFO is filled again. In reality
undeflow conditions seem to confuse internal state machine from time to
time and the whole stream gets shifted by one byte (as captured by logic
analyser on the I2S outputs). One could only hear noise instead of original
stream and this continues until the FIFO is disabled and enabled again.

Work this around by watching underflow interrupt and resetting I2S TX
channel + fill FIFO with zero samples until DMA catches up again. This is
a nasty workaround, but it works. Hence, Kconfig option to disable it in
case of problems.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to "EP93xx User’s Guide" it's called I2SINTR and has number 60.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The driver never supported more than 2 channels because of
ep93xx_i2s_dma_data[] supporting only 1 DMA channel in each
direction.
Stop enabling two unused I2S controller FIFOs, this will simplify
future interrupt support.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Lenovo Ideapad Mixx 320 has a digital mic connected to DMIC2
add a DMI based quirk pointing to the intel_braswell_platform_data
for devices with a mic on DMIC2.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Lenovo Ideapad Mixx 310 has a differential internal analog mic,
add platform-data for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

All DAI drivers are now using the new sdma-pcm platform driver. The
omap-pcm can be removed from the tree, but we need to keep the SND_OMAP_SOC
Kconfig option until the relevant defconfigs are updated to avoid
regression due to missing audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the new platform driver in case of sDMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Set the "realtek,in1-differential" or "realtek,in3-differential"
device-property when the BYT_RT5640_DIFF_MIC quirk is set instead of
directly poking the codec registers.

This also fixes the BYT_RT5640_DIFF_MIC quirk not working when
combined with BYT_RT5640_IN3_MAP.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When platform_clock_control() first selects PLL1 as sysclk the PLL_CTRL
registers have not been setup yet and we effectively have an invalid clock
configuration until byt_rt5640_aif1_hw_params() gets called.

Add a new byt_rt5640_prepare_and_enable_pll1() helper and use that from
both platform_clock_control() and byt_rt5640_aif1_hw_params() to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Enable button press detection for headsets by using the ovcd IRQ to get
notified of button presses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add jack-detect support, loosely based on earlier work on this by:

Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Francisco mendez <francisco.mendez@intel.com>

Note getting the OVCD to work reliable was sort of finicky, so there are
quite a few comments on this to hopefully avoid people breaking it in the
future.

This (and the follow-up button press support) has been tested on the
following devices:

Acer Iconia Tab 8 W1-810
Asus T100CHI
Asus T100TA
Asus T200TA
Axxo WT1011
Chuwi Vi8
Dell Venue 8 Pro 5830
HP Pavilion X2 10-n000nd
HP Stream 7
I.T. Works TW891
Lamina I8270
MSI S100
Peaq C1010
Pipo W4
PoV MobiiTAB-P800W (v2.0)
Toshiba Click Mini L9W-B

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196377Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Allow specifying dmic data pins through device-properties / dt. This will
allow us to stop exporting rt5640_dmic_enable() once all callers of it have
been converted to setting device-properties for this instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

On some platforms the platform code may need to add device-properties,
rather then relying only on properties set by the firmware.

This commit moves the parsing of the device-properties from the i2c-driver
probe() function, which may be called at any time, to the component-driver
probe() function, which gets called after the platform code calls
snd_soc_register_card().

This allows the platform code to attach extra device-properties before
the device-properties are parsed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There are no in tree users of platform-data for the rt5640 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add devicetree-bindings for the dmic, jack-detect source and overcurrent-
detect threshold settings.

The dmic bindings mirror the existing bindings for the rt5645.
The jd-src and ovcd bindings mirror the existing bindings for the rt5651.

Cc devicetree@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5640_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.

RT5640_GBL_CLK is changed by rt5640_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.

This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.

This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5640_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Trivial fix to spelling mistake in dev_err message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds controllers for digital volume of PCM output. Volume
effects simply linear, not dB scale as follows:
  Gained PCM = Original * 0x4000 / Volume

The value range of volume is from 0x0001 to 0xffff. 0x0000 works as
mute. Initial value is 0x4000 (+0dB).
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We can get legacy dai name flag from component driver.
Thus, there is no need to have its parameter on snd_soc_register_dais().
Let's remove unneeded parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>