USB 3.0 hubs can be put into a mode where the hub can automatically
request that the link go into a deeper link power state after the link
has been idle for a specified amount of time.  Each of the new USB 3.0
link states (U1 and U2) have their own timeout that can be programmed
per port.

Change the xHCI roothub emulation code to handle the request to set the
U1 and U2 timeouts.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero.  Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.

This patch should be backported to kernels as old as 2.6.32,
that contain the commit 913a8a34
"USB: xhci: Change how xHCI commands are handled."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Some more data structures must be freed and counters
reset if an XHCI controller has lost power. The failure
to do so renders some chips inoperative after a certain number
of S4 cycles.

This patch should be backported to kernels as old as 3.2,
that contain the commits c29eea62
"xhci: Implement HS/FS/LS bandwidth checking." and
commit 839c817c
"xhci: Implement HS/FS/LS bandwidth checking."
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

USB2 LPM is disabled when device begin to suspend and enabled after device
is resumed. That's because USB spec does not define the transition from
U1/U2 state to U3 state.

If usb_port_suspend() fails, usb_port_resume() is never called, and USB2 LPM
is disabled in this situation. Enable USB2 LPM if port suspend fails.

This patch should be backported to kernels as old as 3.2, that contain
the commit 65580b43 "xHCI: set USB2
hardware LPM".
Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic".  When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine.  The device is:

Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset

The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.

The successful completion code and non-zero untransferred length is a
contradiction.  The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred.  Otherwise, the transfer
should be marked with a short packet completion code.  Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length.  With it, we know to trust
the untransferred length.

Add a new xHCI quirk for the Fresco Logic host controller.  If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning.  For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.

This should be backported to stable kernels that contain the commit
f5182b41 "xhci: Disable MSI for some
Fresco Logic hosts."  That commit was marked for stable kernels as old
as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sergio Correia <lists@uece.net>
Tested-by: Sergio Correia <lists@uece.net>
Cc: stable@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

Fixed keyword related space issues found by
checkpatch.pl tool in drivers/usb/storage/usb.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed several trailing white spaces issues found
by checkpatch.pl tool in drivers/usb/storage/usb.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed C99 comment issue in drivers/usb/storage/usb.c
found using checkpatch.pl tool.
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge branch 'v3.5-for-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into usb-next

This reverts commit 6971113e.

As Alan pointed out, this really isn't needed as it doesn't handle this
properly.  Ideally this should be handled by the usb-serial core one
day.  So revert it.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the usb-serial driver doesn't have a reset_resume callback, then we
need to tell the USB core that it doesn't, and it needs to rebind the
device.

Thanks to Alan for pointing out my mistake, and providing the fix.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I hooked up the wrong callback in my previous patch, this should fix it.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds platform data for using S3C-HSOTG driver at
Universal_C210 target.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds hsotg device to the NURI board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[Rebased on the newest git/kgene/linux-samsung #for-next]
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds hsotg device to the GONI board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch supports to control usb otg phy of EXYNOS4210.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[Rebased on the newest git/kgene/linux-samsung #for-next]
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
[kgene.kim@samsung.com: squashed 2 patches together]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add FunctionFS support.
It allows certain USB functions to be provided from userspace, e.g. MTP,
PTP, adb.

The functions provided by the gadget itself are enumerated in
/sys/class/ccg0/functions. The functions which can be supplied
from userspace must be enumerated in /sys/class/ccg0/f_fs/user_functions.
No other userspace functions can be used than specified in the above mentioned
file, but just specifying them there is not enough to activate them.
The userspace functions in order to be activated need also be enumerated
in /sys/class/ccg0/functions.

An example sequence of operations can be as follows:

$ echo 0 > /sys/class/ccg_usb/ccg0/enable

$ echo -n 0x2d01 > /sys/module/g_ccg/parameters/idProduct
$ echo -n MyDevice > /sys/module/g_ccg/parameters/iSerialNumber
$ echo -n 0x1d6b > /sys/module/g_ccg/parameters/idVendor
$ echo -n Manufacturer > /sys/module/g_ccg/parameters/iManufacturer
$ echo -n Product > /sys/module/g_ccg/parameters/iProduct
$ echo -n bcdDevice > /sys/module/g_ccg/parameters/bcdDevice

$ echo adb,mtp,ptp > /sys/class/ccg_usb/ccg0/f_fs/user_functions
$ echo mass_storage,ptp > /sys/class/ccg_usb/ccg0/functions
$ echo /file.img > /sys/class/ccg_usb/ccg0/f_mass_storage/lun/file

$ mkdir -p /dev/usbgadget/ptp
$ mount -t functionfs ptp /dev/usbgadget/ptp
$ ./ptp &

$ echo 1 > /sys/class/ccg_usb/ccg0/enable

The above example declares that adb, mtp and ptp functions can be supplied
from userspace through FunctionFS. But of them all only ptp is actually
activated, together with mass_storage, the latter being implemented in
the gadget itself (in kernel, not in userspace). The list of functions
can be modified at runtime while the gadget is not enabled, that is,
after

$ echo 0 > /sys/class/ccg_usb/ccg0/enable

The FunctionFS function is implicitly handled by the gadget, that is,
if a userspace function name is provided in
/sys/class/ccg_usb/ccg0/functions, then the FunctionFS function
is activated.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Configurable Gadget driver is a composite driver that allows
userspace to change at runtime the list of functions enabled in
its configuration and to configure these functions. It supports
multiple functions: acm, rndis, and mass storage.

It is usually controlled by a daemon that changes the configuration
based on user settings. For example, rndis is enabled when the user
enables sharing the phone data connection.

As an example on how to use it, the following shell commands will
make the gadget disconnect from the host and make it be re-enumerated
as a composite with 1 rndis and 2 acm interfaces, and a different
product id:

echo 0       > /sys/class/ccg_usb/ccg0/enable
echo rndis,acm > /sys/class/ccg_usb/ccg0/functions
echo 2       > /sys/class/ccg_usb/ccg0/f_acm/instances
echo -n 0x2d01 > /sys/module/g_ccg/parameters/idProduct
echo 1       > /sys/class/ccg_usb/ccg0/enable

The driver requires a gadget controller that supports software
control of the D+ pullup and the controller driver must support
disabling the pullup during composite_bind.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Signed-off-by: Benoit Goby <benoit@android.com>
	[import from android.c, implement review comments, remove adb,mtp,ptp,accessory]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make some noise during probe to make sure the users
are aware of the intended purpose of this driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The patch 5a6506f0 (Update at91_udc to use usb_endpoint_descriptor inside the
struct usb_ep) removes the desc field of struct at91_ep. This convertion had
not been completed which leads to a compilation error.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit da0af6e7 ("usb: Bind devices to ACPI devices when possible") really
tries to force-bind devices even when impossible, unlike what it says in
the subject.

CONFIG_ACPI is not an indication that ACPI tables are actually present, nor
is an indication that any USB relevant information is present in them. There
is no reason to fail the creation of a USB bus if it can't bind it to
ACPI device during initialization.

On systems with CONFIG_ACPI set but without ACPI tables it would cause a
boot panic.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the symbolserial.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the spcp8x5.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the qcserial.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Thomas Tuttle <ttuttle@chromium.org>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the navman.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the ir-usb.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the ipaq.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the generic.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the f81232.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the belkin_sa.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the ark3116.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dbg() is a usb-serial specific macro.  This patch converts
the aircable.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.

CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A few patches ago, I removed the reset_resume callback in this driver.
Now that the usb-serial core supports reset_resume, put this driver
callback back as well, so it should work identically to how it was
originally.

Now if this function really is doing what it should be doing, well,
that's a different story, but we are at least doing the identical thing
that we were before...

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A few patches ago, I removed the reset_resume callback, changing it to
resume instead.  Now that the usb-serial core supports reset_resume, put
this driver callback back as well, so it should work identically to how
it was originally.

Now if this function really is doing what it should be doing, well,
that's a different story, but we are at least doing the identical thing
that we were before...

Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The callback is now hooked up for any USB to serial driver that wants
it.  We only register the callback if any of the usb-serial structures
want it, this keeps the USB core happy.

Thanks to Alan Stern for the ideas on how to do this.

Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's 0 for host only device.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use usb_put_hcd() call instead of usb_remove_hcd() as that's the appropriate
call to drop hcd which failed registration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The CI13xxx usb host needs the root TT support to work properly.
Allow selecting this for the CI13xxx too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As real device-nodes managed by udev whose nodes lived in /dev/bus/usb
are mostly used today, let testusb tool use that directory as one default
path make tool be more convenient to use.
Signed-off-by: Du Changbin <changbinx.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1556) works around a bug in the Philips ISP1562 EHCI
controller.  Although the controller claims to support frame-list
lengths smaller than the default of 1024 for its periodic schedule, in
fact smaller values don't work.  A new quirk flag is added to indicate
when the bug is present, and if it is then the schedule size is left
at the default value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>