- 19 Oct, 2022 1 commit
-
-
Christian König authored
Setting this flag on a scheduler fence prevents pipelining of jobs depending on this fence. In other words we always insert a full CPU round trip before dependent jobs are pushed to the pipeline. Signed-off-by:
Christian König <christian.koenig@amd.com> Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2113#note_1579296Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Acked-by:
Luben Tuikov <luben.tuikov@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221014081553.114899-1-christian.koenig@amd.com
-
- 13 Oct, 2022 3 commits
-
-
Maxime Ripard authored
If our HSM clock has not been properly initialized, any register access will silently lock up the system. Let's check that this can't happen by adding a check for the rate before any register access, and error out otherwise. Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/Reviewed-by:
Javier Martinez Canillas <javierm@redhat.com> Tested-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220929-rpi-pi3-unplugged-fixes-v1-2-cd22e962296c@cerno.tech
-
Maxime Ripard authored
This is a revert of commit fd5894fa ("drm/vc4: hdmi: Remove clock rate initialization"), with the code slightly moved around. It turns out that we can't downright remove that code from the driver, since the Pi0-3 and Pi4 are in different cases, and it only works for the Pi4. Indeed, the commit mentioned above was relying on the RaspberryPi firmware clocks driver to initialize the rate if it wasn't done by the firmware. However, the Pi0-3 are using the clk-bcm2835 clock driver that wasn't doing this initialization. We therefore end up with the clock not being assigned a rate, and the CPU stalling when trying to access a register. We can't move that initialization in the clk-bcm2835 driver, since the HSM clock we depend on is actually part of the HDMI power domain, so any rate setup is only valid when the power domain is enabled. Thus, we reinstated the minimum rate setup at runtime_suspend, which should address both issues. Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/ Fixes: fd5894fa ("drm/vc4: hdmi: Remove clock rate initialization") Reported-by:
Marc Kleine-Budde <mkl@pengutronix.de> Reviewed-by:
-
Maxime Ripard authored
The VC4 HDMI controller driver relies on the HDMI codec ASoC driver. In order to set it up properly, in vc4_hdmi_audio_init(), our HDMI driver will register a device matching the HDMI codec driver, and then register an ASoC card using that codec. However, if vc4 is compiled as a module, chances are that the hdmi-codec driver will be too. In such a case, the module loader will have a very narrow window to load the module between the device registration and the card registration. If it fails to load the module in time, the card registration will fail with EPROBE_DEFER, and we'll abort the audio initialisation, unregistering the HDMI codec device in the process. The next time the bind callback will be run, it's likely that we end up missing that window again, effectively preventing vc4 to probe entirely. In order to prevent this, we can create a soft dependency of the vc4 driver on the HDMI codec one so that we're sure the HDMI codec will be loaded before the VC4 module is, and thus we'll never end up in the previous situation. Fixes: 91e99e11 ("drm/vc4: hdmi: Register HDMI codec") Reviewed-by:
-
- 23 Sep, 2022 4 commits
-
-
Brian Norris authored
This reverts commit 211f276e. For quite some time, core DRM helpers already ensure that any relevant connectors/CRTCs/etc. are disabled, as well as their associated components (e.g., bridges) when suspending the system. Thus, analogix_dp_bridge_{enable,disable}() already get called, which in turn call drm_panel_{prepare,unprepare}(). This makes these drm_panel_*() calls redundant. Besides redundancy, there are a few problems with this handling: (1) drm_panel_{prepare,unprepare}() are *not* reference-counted APIs and are not in general designed to be handled by multiple callers -- although some panel drivers have a coarse 'prepared' flag that mitigates some damage, at least. So at a minimum this is redundant and confusing, but in some cases, this could be actively harmful. (2) The error-handling is a bit non-standard. We ignored errors in suspend(), but handled errors in resume(). And recently, people noticed that the clk handling is unbalanced in error paths, and getting *that* right is not actually trivial, given the current way errors are mostly ignored. (3) In the particular way analogix_dp_{suspend,resume}() get used (e.g., in rockchip_dp_*(), as a late/early callback), we don't necessarily have a proper PM relationship between the DP/bridge device and the panel device. So while the DP bridge gets resumed, the panel's parent device (e.g., platform_device) may still be suspended, and so any prepare() calls may fail. So remove the superfluous, possibly-harmful suspend()/resume() handling of panel state. Fixes: 211f276e ("drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time") Link: https://lore.kernel.org/all/Yv2CPBD3Picg%2FgVe@google.com/Signed-off-by:
Brian Norris <briannorris@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
Francesco Dolcini authored
Correct I2C address for the register list in lt8912_write_lvds_config(), these registers are on the first I2C address (0x48), the current function is just writing garbage to the wrong registers and this creates multiple issues (artifacts and output completely corrupted) on some HDMI displays. Correct I2C address comes from Lontium documentation and it is the one used on other out-of-tree LT8912B drivers [1]. [1] https://github.com/boundarydevices/linux/blob/boundary-imx_5.10.x_2.0.0/drivers/video/lt8912.c#L296 Fixes: 30e2ae94 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge") Signed-off-by:
Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by:
Philippe Schenker <philippe.schenker@toradex.com> Acked-by:
Adrien Grassein <adrien.grassein@gmail.com> Signed-off-by:
Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220922124306.34729-4-dev@pschenker.ch
-
Philippe Schenker authored
The Lontium LT8912 does have a setting for DVI or HDMI. This patch reads from EDID what the display needs and sets it accordingly. Fixes: 30e2ae94 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge") Signed-off-by:
-
Philippe Schenker authored
Currently the bridge driver does not take care whether or not the display needs positive/negative vertical/horizontal syncs. Pass these two flags to the bridge from the EDID that was read out from the display. Fixes: 30e2ae94 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge") Signed-off-by:
-
- 20 Sep, 2022 2 commits
-
-
Randy Dunlap authored
The Kconfig symbol depended on MMU but was dropped by the commit acad3fe6 ("drm/hisilicon: Removed the dependency on the mmu") because it already had as a dependency ARM64 that already selects MMU. But later, commit a0f25a6b ("drm/hisilicon/hibmc: Allow to be built if COMPILE_TEST is enabled") allowed the driver to be built for non-ARM64 when COMPILE_TEST is set but that could lead to unmet direct dependencies and linking errors. Prevent a kconfig warning when MMU is not enabled by making DRM_HISI_HIBMC depend on MMU. WARNING: unmet direct dependencies detected for DRM_TTM Depends on [n]: HAS_IOMEM [=y] && DRM [=m] && MMU [=n] Selected by [m]: - DRM_TTM_HELPER [=m] && HAS_IOMEM [=y] && DRM [=m] - DRM_HISI_HIBMC [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && (ARM64 || COMPILE_TEST [=y]) Fixes: acad3fe6 ("drm/hisilicon: Removed the dependency on the mmu") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Gerd Hoffmann <kraxel@redhat.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Xinliang Liu <xinliang.liu@linaro.org> Cc: Tian Tao <tiantao6@hisilicon.com> Cc: John Stultz <jstultz@google.com> Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com> Cc: Chen Feng <puck.chen@hisilicon.com> Cc: Christian Koenig <christian.koenig@amd.com> Cc: Huang Rui <ray.huang@amd.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Reviewed-by:
-
Thomas Zimmermann authored
G200ER does not seem to support 24 bpp, so force the console to use 32 bpp. The problem got introduced when commit 73f54d5d ("drm/mgag200: Remove special case for G200SE with <2 MiB") changed the preferred color depth from 32 bit to 24 bit. A setting of 24 is the correct color depth, but G200ER doesn't seem to be able to use the respective RGB888 color format. Using 24-bit color with forced 32 bpp works around the problem. Reported-by:
Wang Yugui <wangyugui@e16-tech.com> Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Tested-by:
Jocelyn Falempe <jfalempe@redhat.com> Fixes: 73f54d5d ("drm/mgag200: Remove special case for G200SE with <2 MiB") Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Jocelyn Falempe <jfalempe@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Cc: dri-devel@lists.freedesktop.org Link: https://patchwork.freedesktop.org/patch/msgid/20220915150348.31504-1-tzimmermann@suse.de
-
- 19 Sep, 2022 1 commit
-
-
Heiko Schocher authored
innolux_g121i1_l01 sets bpc to 6, so use the corresponding bus format: MEDIA_BUS_FMT_RGB666_1X7X3_SPWG. Fixes: 4ae13e48 ("drm/panel: simple: Add more properties to Innolux G121I1-L01") Signed-off-by:
Heiko Schocher <hs@denx.de> Signed-off-by:
Fabio Estevam <festevam@denx.de> Signed-off-by:
Marek Vasut <marex@denx.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220826165021.1592532-1-festevam@denx.de
-
- 14 Sep, 2022 1 commit
-
-
Nathan Huckleberry authored
The mode_valid field in drm_connector_helper_funcs is expected to be of type: enum drm_mode_status (* mode_valid) (struct drm_connector *connector, struct drm_display_mode *mode); The mismatched return type breaks forward edge kCFI since the underlying function definition does not match the function hook definition. The return type of cdn_dp_connector_mode_valid should be changed from int to enum drm_mode_status. Reported-by:
Dan Carpenter <error27@gmail.com> Link: https://github.com/ClangBuiltLinux/linux/issues/1703 Cc: llvm@lists.linux.dev Signed-off-by:
Nathan Huckleberry <nhuck@google.com> Reviewed-by:
Nathan Chancellor <nathan@kernel.org> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220913205555.155149-1-nhuck@google.com
-
- 09 Sep, 2022 6 commits
-
-
Sascha Hauer authored
The hsync/vsync polarities were not honoured for the eDP and HDMI ports. Add the register settings to configure the polarities as requested by the DRM_MODE_FLAG_PHSYNC/DRM_MODE_FLAG_PVSYNC flags. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Fixes: 604be855 ("drm/rockchip: Add VOP2 driver") Tested-by:
Michael Riesch <michael.riesch@wolfvision.net> Signed-off-by:
-
Hans de Goede authored
Fix gnome-shell (and other page-flip users) hanging after suspend/resume because of the gma500's IRQs not working. This fixes 2 problems with the IRQ handling: 1. gma_power_off() calls gma_irq_uninstall() which does a free_irq(), but gma_power_on() called gma_irq_preinstall() + gma_irq_postinstall() which do not call request_irq. Replace the pre- + post-install calls with gma_irq_install() which does prep + request + post. 2. After fixing 1. IRQs still do not work on a Packard Bell Dot SC (Intel Atom N2600, cedarview) netbook. Cederview uses MSI interrupts and it seems that the BIOS re-configures things back to normal APIC based interrupts during S3 suspend. There is some MSI PCI-config registers save/restore code which tries to deal with this, but on the Packard Bell Dot SC this is not sufficient to restore MSI IRQ functionality after a suspend/resume. Replace the PCI-config registers save/restore with pci_disable_msi() on suspend + pci_enable_msi() on resume. Fixing e.g. gnome-shell hanging. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220906203852.527663-4-hdegoede@redhat.com
-
Hans de Goede authored
psb_gem_unpin() calls dma_resv_lock() but the underlying ww_mutex gets destroyed by drm_gem_object_release() move the drm_gem_object_release() call in psb_gem_free_object() to after the unpin to fix the below warning: [ 79.693962] ------------[ cut here ]------------ [ 79.693992] DEBUG_LOCKS_WARN_ON(lock->magic != lock) [ 79.694015] WARNING: CPU: 0 PID: 240 at kernel/locking/mutex.c:582 __ww_mutex_lock.constprop.0+0x569/0xfb0 [ 79.694052] Modules linked in: rfcomm snd_seq_dummy snd_hrtimer qrtr bnep ath9k ath9k_common ath9k_hw snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_codec_hdmi snd_hda_intel ath3k snd_intel_dspcfg mac80211 snd_intel_sdw_acpi btusb snd_hda_codec btrtl btbcm btintel btmtk bluetooth at24 snd_hda_core snd_hwdep uvcvideo snd_seq libarc4 videobuf2_vmalloc ath videobuf2_memops videobuf2_v4l2 videobuf2_common snd_seq_device videodev acer_wmi intel_powerclamp coretemp mc snd_pcm joydev sparse_keymap ecdh_generic pcspkr wmi_bmof cfg80211 i2c_i801 i2c_smbus snd_timer snd r8169 rfkill lpc_ich soundcore acpi_cpufreq zram rtsx_pci_sdmmc mmc_core serio_raw rtsx_pci gma500_gfx(E) video wmi ip6_tables ip_tables i2c_dev fuse [ 79.694436] CPU: 0 PID: 240 Comm: plymouthd Tainted: G W E 6.0.0-rc3+ #490 [ 79.694457] Hardware name: Packard Bell dot s/SJE01_CT, BIOS V1.10 07/23/2013 [ 79.694469] RIP: 0010:__ww_mutex_lock.constprop.0+0x569/0xfb0 [ 79.694496] Code: ff 85 c0 0f 84 15 fb ff ff 8b 05 ca 3c 11 01 85 c0 0f 85 07 fb ff ff 48 c7 c6 30 cb 84 aa 48 c7 c7 a3 e1 82 aa e8 ac 29 f8 ff <0f> 0b e9 ed fa ff ff e8 5b 83 8a ff 85 c0 74 10 44 8b 0d 98 3c 11 [ 79.694513] RSP: 0018:ffffad1dc048bbe0 EFLAGS: 00010282 [ 79.694623] RAX: 0000000000000028 RBX: 0000000000000000 RCX: 0000000000000000 [ 79.694636] RDX: 0000000000000001 RSI: ffffffffaa8b0ffc RDI: 00000000ffffffff [ 79.694650] RBP: ffffad1dc048bc80 R08: 0000000000000000 R09: ffffad1dc048ba90 [ 79.694662] R10: 0000000000000003 R11: ffffffffaad62fe8 R12: ffff9ff302103138 [ 79.694675] R13: ffff9ff306ec8000 R14: ffff9ff307779078 R15: ffff9ff3014c0270 [ 79.694690] FS: 00007ff1cccf1740(0000) GS:ffff9ff3bc200000(0000) knlGS:0000000000000000 [ 79.694705] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 79.694719] CR2: 0000559ecbcb4420 CR3: 0000000013210000 CR4: 00000000000006f0 [ 79.694734] Call Trace: [ 79.694749] <TASK> [ 79.694761] ? __schedule+0x47f/0x1670 [ 79.694796] ? psb_gem_unpin+0x27/0x1a0 [gma500_gfx] [ 79.694830] ? lock_is_held_type+0xe3/0x140 [ 79.694864] ? ww_mutex_lock+0x38/0xa0 [ 79.694885] ? __cond_resched+0x1c/0x30 [ 79.694902] ww_mutex_lock+0x38/0xa0 [ 79.694925] psb_gem_unpin+0x27/0x1a0 [gma500_gfx] [ 79.694964] psb_gem_unpin+0x199/0x1a0 [gma500_gfx] [ 79.694996] drm_gem_object_release_handle+0x50/0x60 [ 79.695020] ? drm_gem_object_handle_put_unlocked+0xf0/0xf0 [ 79.695042] idr_for_each+0x4b/0xb0 [ 79.695066] ? _raw_spin_unlock_irqrestore+0x30/0x60 [ 79.695095] drm_gem_release+0x1c/0x30 [ 79.695118] drm_file_free.part.0+0x1ea/0x260 [ 79.695150] drm_release+0x6a/0x120 [ 79.695175] __fput+0x9f/0x260 [ 79.695203] task_work_run+0x59/0xa0 [ 79.695227] do_exit+0x387/0xbe0 [ 79.695250] ? seqcount_lockdep_reader_access.constprop.0+0x82/0x90 [ 79.695275] ? lockdep_hardirqs_on+0x7d/0x100 [ 79.695304] do_group_exit+0x33/0xb0 [ 79.695331] __x64_sys_exit_group+0x14/0x20 [ 79.695353] do_syscall_64+0x58/0x80 [ 79.695376] ? up_read+0x17/0x20 [ 79.695401] ? lock_is_held_type+0xe3/0x140 [ 79.695429] ? asm_exc_page_fault+0x22/0x30 [ 79.695450] ? lockdep_hardirqs_on+0x7d/0x100 [ 79.695473] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 79.695493] RIP: 0033:0x7ff1ccefe3f1 [ 79.695516] Code: Unable to access opcode bytes at RIP 0x7ff1ccefe3c7. [ 79.695607] RSP: 002b:00007ffed4413378 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 [ 79.695629] RAX: ffffffffffffffda RBX: 00007ff1cd0159e0 RCX: 00007ff1ccefe3f1 [ 79.695644] RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000000 [ 79.695656] RBP: 0000000000000000 R08: ffffffffffffff80 R09: 00007ff1cd020b20 [ 79.695671] R10: 0000000000000000 R11: 0000000000000246 R12: 00007ff1cd0159e0 [ 79.695684] R13: 0000000000000000 R14: 00007ff1cd01aee8 R15: 00007ff1cd01af00 [ 79.695733] </TASK> [ 79.695746] irq event stamp: 725979 [ 79.695757] hardirqs last enabled at (725979): [<ffffffffa9132d54>] finish_task_switch.isra.0+0xe4/0x3f0 [ 79.695780] hardirqs last disabled at (725978): [<ffffffffa9eb4113>] __schedule+0xdd3/0x1670 [ 79.695803] softirqs last enabled at (725974): [<ffffffffa90fbc9d>] __irq_exit_rcu+0xed/0x160 [ 79.695825] softirqs last disabled at (725969): [<ffffffffa90fbc9d>] __irq_exit_rcu+0xed/0x160 [ 79.695845] ---[ end trace 0000000000000000 ]--- Signed-off-by:
-
Hans de Goede authored
gma_crtc_page_flip() was holding the event_lock spinlock while calling crtc_funcs->mode_set_base() which takes ww_mutex. The only reason to hold event_lock is to clear gma_crtc->page_flip_event on mode_set_base() errors. Instead unlock it after setting gma_crtc->page_flip_event and on errors re-take the lock and clear gma_crtc->page_flip_event it it is still set. This fixes the following WARN/stacktrace: [ 512.122953] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:870 [ 512.123004] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 1253, name: gnome-shell [ 512.123031] preempt_count: 1, expected: 0 [ 512.123048] RCU nest depth: 0, expected: 0 [ 512.123066] INFO: lockdep is turned off. [ 512.123080] irq event stamp: 0 [ 512.123094] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [ 512.123134] hardirqs last disabled at (0): [<ffffffff8d0ec28c>] copy_process+0x9fc/0x1de0 [ 512.123176] softirqs last enabled at (0): [<ffffffff8d0ec28c>] copy_process+0x9fc/0x1de0 [ 512.123207] softirqs last disabled at (0): [<0000000000000000>] 0x0 [ 512.123233] Preemption disabled at: [ 512.123241] [<0000000000000000>] 0x0 [ 512.123275] CPU: 3 PID: 1253 Comm: gnome-shell Tainted: G W 5.19.0+ #1 [ 512.123304] Hardware name: Packard Bell dot s/SJE01_CT, BIOS V1.10 07/23/2013 [ 512.123323] Call Trace: [ 512.123346] <TASK> [ 512.123370] dump_stack_lvl+0x5b/0x77 [ 512.123412] __might_resched.cold+0xff/0x13a [ 512.123458] ww_mutex_lock+0x1e/0xa0 [ 512.123495] psb_gem_pin+0x2c/0x150 [gma500_gfx] [ 512.123601] gma_pipe_set_base+0x76/0x240 [gma500_gfx] [ 512.123708] gma_crtc_page_flip+0x95/0x130 [gma500_gfx] [ 512.123808] drm_mode_page_flip_ioctl+0x57d/0x5d0 [ 512.123897] ? drm_mode_cursor2_ioctl+0x10/0x10 [ 512.123936] drm_ioctl_kernel+0xa1/0x150 [ 512.123984] drm_ioctl+0x21f/0x420 [ 512.124025] ? drm_mode_cursor2_ioctl+0x10/0x10 [ 512.124070] ? rcu_read_lock_bh_held+0xb/0x60 [ 512.124104] ? lock_release+0x1ef/0x2d0 [ 512.124161] __x64_sys_ioctl+0x8d/0xd0 [ 512.124203] do_syscall_64+0x58/0x80 [ 512.124239] ? do_syscall_64+0x67/0x80 [ 512.124267] ? trace_hardirqs_on_prepare+0x55/0xe0 [ 512.124300] ? do_syscall_64+0x67/0x80 [ 512.124340] ? rcu_read_lock_sched_held+0x10/0x80 [ 512.124377] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 512.124411] RIP: 0033:0x7fcc4a70740f [ 512.124442] Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <89> c2 3d 00 f0 ff ff 77 18 48 8b 44 24 18 64 48 2b 04 25 28 00 00 [ 512.124470] RSP: 002b:00007ffda73f5390 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 512.124503] RAX: ffffffffffffffda RBX: 000055cc9e474500 RCX: 00007fcc4a70740f [ 512.124524] RDX: 00007ffda73f5420 RSI: 00000000c01864b0 RDI: 0000000000000009 [ 512.124544] RBP: 00007ffda73f5420 R08: 000055cc9c0b0cb0 R09: 0000000000000034 [ 512.124564] R10: 0000000000000000 R11: 0000000000000246 R12: 00000000c01864b0 [ 512.124584] R13: 0000000000000009 R14: 000055cc9df484d0 R15: 000055cc9af5d0c0 [ 512.124647] </TASK> Signed-off-by:
-
Stuart Menefy authored
VPP_WRAP_OSD1_MATRIX_COEF22.Coeff22 is documented as being bits 0-12, not 16-28. Without this the output tends to have a pink hue, changing it results in better color accuracy. The vendor kernel doesn't use this register. However the code which sets VIU2_OSD1_MATRIX_COEF22 also uses bits 0-12. There is a slightly different style of registers for configuring some of the other matrices, which do use bits 16-28 for this coefficient, but those have names ending in MATRIX_COEF22_30, and this is not one of those. Signed-off-by:
Stuart Menefy <stuart.menefy@mathembedded.com> Fixes: 72888394 ("drm/meson: Add G12A Support for VIU setup") Reviewed-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
Stuart Menefy authored
VIU_OSD1_CTRL_STAT.GLOBAL_ALPHA is a 9 bit field, so the maximum value is 0x100 not 0xff. This matches the vendor kernel. Signed-off-by:
-
- 08 Sep, 2022 3 commits
-
-
Chen-Yu Tsai authored
Commit 52824ca4 ("drm/panel-edp: Better describe eDP panel delays") clarified the various delays used for eDP panels, tying them to the eDP panel timing diagram. For Innolux N116BCA-EA1, .prepare_to_enable would be: t4_min + t5_min + t6_min + max(t7_max, t8_min) Since t4_min and t5_min are both 0, the panel can use either .enable or .prepare_to_enable. As .enable is better defined, switch to using .enable for this panel. Also add .disable = 50, based on the datasheet's t9_min value. This effectively makes the delays the same as delay_200_500_e80_d50. Cc: Douglas Anderson <dianders@chromium.org> Fixes: 51d35631 ("drm/panel-simple: Add N116BCA-EA1") Signed-off-by:
Chen-Yu Tsai <wenst@chromium.org> Reviewed-by:
-
Clément Péron authored
Enabling panfrost GPU OPP with dynamic regulator will make OPP responsible to enable and configure it. Unfortunately OPP configure and enable the regulator when an OPP is asked to be set, which is not the case during panfrost_devfreq_init(). This leave the regulator unconfigured and if no GPU load is triggered, no OPP is asked to be set which make the regulator framework switching it off during regulator_late_cleanup() without noticing and therefore make the board hang as any access to GPU memory space make bus locks up. Call dev_pm_opp_set_opp() with the recommend OPP in panfrost_devfreq_init() to enable the regulator, this will properly configure and enable the regulator and will avoid any switch off by regulator_late_cleanup(). Suggested-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Clément Péron <peron.clem@gmail.com> Reviewed-by:
Steven Price <steven.price@arm.com> Signed-off-by:
-
Christian König authored
Otherwise lockdep will complain about cleaning up the bulk_move. Signed-off-by:
Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220907100051.570641-1-christian.koenig@amd.com Fixes: d91c411c ("drm/ttm: update bulk move object of ghost BO")
-
- 06 Sep, 2022 1 commit
-
-
ZhenGuo Yin authored
[Why] Ghost BO is released with non-empty bulk move object. There is a warning trace: WARNING: CPU: 19 PID: 1582 at ttm/ttm_bo.c:366 ttm_bo_release+0x2e1/0x2f0 [amdttm] Call Trace: amddma_resv_reserve_fences+0x10d/0x1f0 [amdkcl] amdttm_bo_put+0x28/0x30 [amdttm] amdttm_bo_move_accel_cleanup+0x126/0x200 [amdttm] amdgpu_bo_move+0x1a8/0x770 [amdgpu] ttm_bo_handle_move_mem+0xb0/0x140 [amdttm] amdttm_bo_validate+0xbf/0x100 [amdttm] [How] The resource of ghost BO should be moved to LRU directly, instead of using bulk move. The bulk move object of ghost BO should set to NULL before function ttm_bo_move_to_lru_tail_unlocked. v2: set bulk move to NULL manually if no resource associated with ghost BO Fixed: 5b951e487fd6bf5f ("drm/ttm: fix bulk move handling v2") Signed-off-by:ZhenGuo Yin <zhenguo.yin@amd.com> Reviewed-by:
-
- 02 Sep, 2022 1 commit
-
-
Ville Syrjälä authored
EDID 1.4 introduced some extra flags in the range descriptor to support min/max h/vfreq >= 255. Consult them to correctly parse the vfreq limits. Note that some combinations of the flags are documented as "reserved" (as are some other values in the descriptor) but explicitly checking for those doesn't seem particularly worthwile since we end up with bogus results whether we decode them or not. v2: Increase the storage to u16 to make it work (Jani) Note the "reserved" values situation (Jani) v3: Document the EDID version number in the defines Drop some bogus (u8) casts Cc: stable@vger.kernel.org Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6519 References: https://gitlab.freedesktop.org/drm/intel/-/issues/6484Reviewed-by:Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220826213501.31490-2-ville.syrjala@linux.intel.comReviewed-by:
Manasi Navare <manasi.d.navare@intel.com>
-
- 25 Aug, 2022 1 commit
-
-
Christian König authored
Previously when we added a fence to a dma_resv object we always assumed the the newer than all the existing fences. With Jason's work to add an UAPI to explicit export/import that's not necessary the case any more. So without this check we would allow userspace to force the kernel into an use after free error. Since the change is very small and defensive it's probably a good idea to backport this to stable kernels as well just in case others are using the dma_resv object in the same way. Signed-off-by:
Jason Ekstrand <jason.ekstrand@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220810172617.140047-1-christian.koenig@amd.com Cc: stable@vger.kernel.org # v5.19+
-
- 23 Aug, 2022 1 commit
-
-
Karol Herbst authored
It is a bit unlcear to us why that's helping, but it does and unbreaks suspend/resume on a lot of GPUs without any known drawbacks. Cc: stable@vger.kernel.org # v5.15+ Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/156Signed-off-by:
Karol Herbst <kherbst@redhat.com> Reviewed-by:
Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220819200928.401416-1-kherbst@redhat.com
-
- 19 Aug, 2022 1 commit
-
-
Jeffy Chen authored
Currently we are assuming a one to one mapping between dmabuf and GEM handle when releasing GEM handles. But that is not always true, since we would create extra handles for the GEM obj in cases like gem_open() and getfb{,2}(). A similar issue was reported at: https://lore.kernel.org/all/20211105083308.392156-1-jay.xu@rock-chips.com/ Another problem is that the imported dmabuf might not always have gem_obj->dma_buf set, which would cause leaks in drm_gem_remove_prime_handles(). Let's fix these for now by using handle to find the exact map to remove. Signed-off-by:Jeffy Chen <jeffy.chen@rock-chips.com> Reviewed-by:
-
- 18 Aug, 2022 2 commits
-
-
Maxime Ripard authored
The current code tries to handle the case where CONFIG_PM isn't selected by first calling our runtime_resume implementation and then properly report the power state to the runtime_pm core. This allows to have a functionning device even if pm_runtime_get_* functions are nops. However, the device power state if CONFIG_PM is enabled is RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls in the runtime_pm hooks will now report a warning since the device might not be properly powered. Even more so, we need CONFIG_PM enabled since the previous RaspberryPi have a power domain that needs to be powered up for the HDMI controller to be usable. The previous patch has created a dependency on CONFIG_PM, now we can just assume it's there and only call pm_runtime_resume_and_get() to make sure our device is powered in bind. Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.techAcked-by:
-
Maxime Ripard authored
We already depend on runtime PM to get the power domains and clocks for most of the devices supported by the vc4 driver, so let's just select it to make sure it's there. Link: https://lore.kernel.org/r/20220629123510.1915022-38-maxime@cerno.techAcked-by:
-
- 17 Aug, 2022 1 commit
-
-
Thomas Zimmermann authored
Backmerging for v6.0-rc1. Signed-off-by:
-
- 15 Aug, 2022 2 commits
-
-
Samuel Holland authored
Currently, the packet overhead is subtracted using unsigned arithmetic. With a short sync pulse, this could underflow and wrap around to near the maximal u16 value. Fix this by using signed subtraction. The call to max() will correctly handle any negative numbers that are produced. Apply the same fix to the other timings, even though those subtractions are less likely to underflow. Fixes: 133add5b ("drm/sun4i: Add Allwinner A31 MIPI-DSI controller support") Signed-off-by:
Samuel Holland <samuel@sholland.org> Reviewed-by:
Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by:
-
Samuel Holland authored
When adding the D1 TCON bindings, I missed the conditional blocks that restrict the binding for TCON LCD vs TCON TV hardware. Add the D1 TCON variants to the appropriate blocks for DE2 TCON LCDs and TCON TVs. Fixes: ae5a5d26 ("dt-bindings: display: Add D1 display engine compatibles") Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
- 14 Aug, 2022 9 commits
-
-
Linus Torvalds authored
-
Yury Norov authored
Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we have gfp_types.h for this. Fixes powerpc allmodconfig build: In file included from include/linux/nodemask.h:97, from include/linux/mmzone.h:17, from include/linux/gfp.h:7, from include/linux/radix-tree.h:12, from include/linux/idr.h:15, from include/linux/kernfs.h:12, from include/linux/sysfs.h:16, from include/linux/kobject.h:20, from include/linux/pci.h:35, from arch/powerpc/kernel/prom_init.c:24: include/linux/random.h: In function 'add_latent_entropy': >> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'? 25 | add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy)); | ^~~~~~~~~~~~~~ | add_latent_entropy include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in Reported-by:kernel test robot <lkp@intel.com> CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com> CC: Andrew Morton <akpm@linux-foundation.org> CC: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by:
Yury Norov <yury.norov@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull vfs lseek fix from Al Viro: "Fix proc_reg_llseek() breakage. Always had been possible if somebody left NULL ->proc_lseek, became a practical issue now" * tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: take care to handle NULL ->proc_lseek()
-
Al Viro authored
Easily done now, just by clearing FMODE_LSEEK in ->f_mode during proc_reg_open() for such entries. Fixes: 868941b1 "fs: remove no_llseek" Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk>
-
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tipLinus Torvalds authored
Pull more xen updates from Juergen Gross: - fix the handling of the "persistent grants" feature negotiation between Xen blkfront and Xen blkback drivers - a cleanup of xen.config and adding xen.config to Xen section in MAINTAINERS - support HVMOP_set_evtchn_upcall_vector, which is more compliant to "normal" interrupt handling than the global callback used up to now - further small cleanups * tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections xen: remove XEN_SCRUB_PAGES in xen.config xen/pciback: Fix comment typo xen/xenbus: fix return type in xenbus_file_read() xen-blkfront: Apply 'feature_persistent' parameter when connect xen-blkback: Apply 'feature_persistent' parameter when connect xen-blkback: fix persistent grants negotiation x86/xen: Add support for HVMOP_set_evtchn_upcall_vector
-
Linus Torvalds authored
Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull more perf tool updates from Arnaldo Carvalho de Melo: - 'perf c2c' now supports ARM64, adjust its output to cope with differences with what is in x86_64. Now go find false sharing on ARM64 (at least Neoverse) as well! - Refactor the JSON processing, making the output more compact and thus reducing the size of the resulting perf binary - Improvements for 'perf offcpu' profiling, including tracking child processes - Update Intel JSON metrics and events files for broadwellde, broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown, knightslanding, sapphirerapids, skylakex and snowridgex - Add 'perf stat' JSON output and a 'perf test' entry for it - Ignore memfd and anonymous mmap events if jitdump present - Refactor 'perf test' shell tests allowing subdirs - Fix an error handling path in 'parse_perf_probe_command()' - Fixes for the guest Intel PT tracing patchkit in the 1st batch of this merge window - Print debuginfod queries if -v option is used, to explain delays in processing when debuginfo servers are enabled to fetch DSOs with richer symbol tables - Improve error message for 'perf record -p not_existing_pid' - Fix openssl and libbpf feature detection - Add PMU pai_crypto event description for IBM z16 on 'perf list' - Fix typos and duplicated words on comments in various places * tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits) perf test: Refactor shell tests allowing subdirs perf vendor events: Update events for snowridgex perf vendor events: Update events and metrics for skylakex perf vendor events: Update metrics for sapphirerapids perf vendor events: Update events for knightslanding perf vendor events: Update metrics for jaketown perf vendor events: Update metrics for ivytown perf vendor events: Update events and metrics for icelakex perf vendor events: Update events and metrics for haswellx perf vendor events: Update events and metrics for cascadelakex perf vendor events: Update events and metrics for broadwellx perf vendor events: Update metrics for broadwellde perf jevents: Fold strings optimization perf jevents: Compress the pmu_events_table perf metrics: Copy entire pmu_event in find metric perf pmu-events: Hide the pmu_events perf pmu-events: Don't assume pmu_event is an array perf pmu-events: Move test events/metrics to JSON perf test: Use full metric resolution perf pmu-events: Hide pmu_events_map ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit CPUs trap on it rather than ignoring it as they should. - Fix ftrace when building with clang, which was broken by some refactoring. - A couple of other minor fixes. Thanks to Christophe Leroy, Naveen N. Rao, Nick Desaulniers, Ondrej Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool. * tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/kexec: Fix build failure from uninitialised variable powerpc/ppc-opcode: Fix PPC_RAW_TW() powerpc64/ftrace: Fix ftrace for clang builds powerpc: Make eh value more explicit when using lwarx powerpc: Don't hide eh field of lwarx behind a macro powerpc: Fix eh field when calling lwarx on PPC32
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull /proc/mounts fix from Al Viro: "Fix for /proc/mounts escaping - escape the '#' character too" * tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: vfs: escape hash as well
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull more cifs updates from Steve French: - two fixes for stable, one for a lock length miscalculation, and another fixes a lease break timeout bug - improvement to handle leases, allows the close timeout to be configured more safely - five restructuring/cleanup patches * tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: cifs: Do not access tcon->cfids->cfid directly from is_path_accessible cifs: Add constructor/destructors for tcon->cfid SMB3: fix lease break timeout when multiple deferred close handles for the same file. smb3: allow deferred close timeout to be configurable cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir cifs: Move cached-dir functions into a separate file cifs: Remove {cifs,nfs}_fscache_release_page() cifs: fix lock length calculation
-
