Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Li Yi <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Li Yi <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Valentin Yakovenkov <yakovenkov@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This is useful for quick tests where networks are faster than compression,
and/or the compression code is broken.
Reported-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

User reports rarely include full information, so include this important
tidbit up front.  It's also good to know at a glance in general.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Every Blackfin variant has the same DMA bit masks, so avoid duplicating
them over and over in each mach header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The driver changed from "isp1760-hcd" to "isp1760", so update resources
to match.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No need to set MSTR in .ctl_reg as the Blackfin SPI bus driver does this
already for all parts.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

There's no point in having mask defines when the entire MMR value is a
count or address.  i.e. applying a mask of -1 is pointless.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

There are no MXVR device drivers, and if someday there is, we can put
these in a dedicated header rather than polluting the global namespace.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

People should not be accessing OTP MMRs directly.  They should instead go
through the Blackfin ROM helper functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The watchdog code doesn't need these, and the other parts had these
punted, so keep the global namespace clean.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The RTC driver code doesn't need these, and the other parts had these
punted, so keep the global namespace clean.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No point in duplicating entire lists when we can simply tail into other
parts for most of the MMRs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

All the other BF54x parts had these defines renamed to avoid collision,
but it looks the BF542 was missed somehow.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The cache lock code was unused and punted, so punt the documentation too.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

We don't need the BKL and now people will stop looking at this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The DMA channel status field was encoding redundant info wrt the DMA MMR
config register, and it was doing an incomplete job of checking all DMA
channels (some drivers write directly to the config register).  So drop
the tristate field in favor of a binary atomic field.  This simplifies
the code in general, removes the implicit need for sleeping, and forces
the suspend code to handle all channels properly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The driver was moved during the merge process, so update the defines to
match the new location.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Avoid including unnecessary headers all the time as well as circular
includes with core requirements.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

All the arches define a helper macro to make things easy for driver code.
Reported-by: Frank Van Hooft <frank@frankvh.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The GPIOs on ports C/D/E on the BF538/BF539 do not behave the same way as
the other ports on the part and the same way as all other Blackfin parts.
The MMRs are programmed slightly different and they cannot be used to
generate interrupts or wakeup a sleeping system.  Since these guys don't
fit into the existing code, create a simple gpiolib driver for them.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Have the C API trace funcs match the assembly API trace funcs.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

PLL_LOCKCNT applies only to the PLL programming sequence which does not
apply to core and system clock dividers.  Writes to PLL_DIV to change the
CSEL/SSEL dividers take effect immediately.

There is still overhead in software in writing the new dividers, so just
use a value of 50us as this should be good enough.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Drop the CONFIG_USB_ISP1362_BFIN_GPIO_IRQ Kconfig as it never made it into
mainline and it was a bad interface into the board resources.  For boards
that actually used this, replace it with an actual IRQ define.  For boards
that didn't, simply drop the resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the link sizes never change at runtime, push the calculation out to
the linker script to save some useless calculation costs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The access_ok() function did not accept ranges within the async banks
which made it impossible to do XIP in flash.  Fixing that also showed
that the current bfin_mem_access_type() code did not work with accesses
that spanned async banks (like a file system).  So split out and fix the
async bank checks so that all these scenarios work as expected.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Rather than using our own data structures that basically boil down to a
bitmap, use the standard bitmap functions.
Reported-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Now that the driver has been updated, convert the board resources to the
new i2c framework for managing slaves.

For boards that don't actually hook up to this hardware, simply drop the
resources altogether.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The requested peripheral is turned into an index into some state arrays,
so make sure the calculated index doesn't exceed the index.  This occurs
when using bogus pin values or the define headers are screwed up.  Now
we'll notice right away that something needs fixing instead of trying to
track down random memory corruption.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No point in redefining things that common code already does for us.  Also
use CYC2NS_SCALE_FACTOR to better reflect reality and for better precision.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Currently sched_clock() is only defined when using CYCLES as a clock
source.  Declare sched_clock() in common code and mark it with notrace to
prevent invoking sched_clock() recursively (because ftrace uses
sched_clock() to record time).
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>