Add the physical switch instance and port index a DSA port belongs to to
the dsa_port structure.

That can be used later to retrieve information about a physical port
when configuring a switch fabric, or lighten up struct dsa_slave_priv.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dsa_switch structure contains the number of ports. Use it where the
structure is valid instead of the DSA_MAX_PORTS value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.

This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
ravb: Support 1Gbps on R-Car H3 ES1.1+ and R-Car M3-W

this series adds support for gigabit communication to the Renesas
EthernetAVB controller when used in conjunction with R-Car Gen3 H3
ES1.1+ and M3-W SoCs.  Gigabit is already supported with R-Car Gen 2
SoCs.

The patch from Geert was previously posted for inclusion in v4.10 and
acked by Dave for that purpose. It was, however, not accepted by the
ARM SoC maintainers.

The path from Mizuguchi-san is to address timing problems observed
with gigabit transfers. I would like it considered although my own
testing on M3-W did not show any timing problems.

Changes since v1:
* Address various feedback for "APSR" patch as noted in its changelog
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The limitation to 10/100Mbit speeds on R-Car Gen3 is valid for R-Car H3
ES1.0 only. Check for the exact SoC model to allow 1Gbps on newer
revisions of R-Car H3, and on R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables tx and rx clock internal delay modes (TDM and RDM).

This is to address a failure in the case of 1Gbps communication using the
by salvator-x board with the KSZ9031RNX phy. This has been reported to
occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.

With this change APSR internal delay modes are enabled for
"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows:

phy mode   | ASPR delay mode
-----------+----------------
rgmii-id   | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The macro is returning ETIME which means various checks to see if
the returned err is less than zero never work. I believe a -ETIME
should be returned instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398318 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398321 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andreas Schultz says:

====================
gtp: simple gtp improvements

This is the part of the previous "simple gtp improvements" series
that Pablo indicated should go into net-next.

The rcu_lock removal is small correctness changes. Passing invalid
to user space allows for more standards compliant handling of invalid
tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

enable userspace to send error replies for invalid tunnels
Acked-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rcu read lock is hold by default in the ip input path. There
is no need to hold it twice in the socket recv decapsulate code path.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two trivial overlapping changes conflicts in MPLS and mlx5.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) GTP fixes from Andreas Schultz (missing genl module alias, clear IP
    DF on transmit).

 2) Netfilter needs to reflect the fwmark when sending resets, from Pau
    Espin Pedrol.

 3) nftable dump OOPS fix from Liping Zhang.

 4) Fix erroneous setting of VIRTIO_NET_HDR_F_DATA_VALID on transmit,
    from Rolf Neugebauer.

 5) Fix build error of ipt_CLUSTERIP when procfs is disabled, from Arnd
    Bergmann.

 6) Fix regression in handling of NETIF_F_SG in harmonize_features(),
    from Eric Dumazet.

 7) Fix RTNL deadlock wrt. lwtunnel module loading, from David Ahern.

 8) tcp_fastopen_create_child() needs to setup tp->max_window, from
    Alexey Kodanev.

 9) Missing kmemdup() failure check in ipv6 segment routing code, from
    Eric Dumazet.

10) Don't execute unix_bind() under the bindlock, otherwise we deadlock
    with splice. From WANG Cong.

11) ip6_tnl_parse_tlv_enc_lim() potentially reallocates the skb buffer,
    therefore callers must reload cached header pointers into that skb.
    Fix from Eric Dumazet.

12) Fix various bugs in legacy IRQ fallback handling in alx driver, from
    Tobias Regnery.

13) Do not allow lwtunnel drivers to be unloaded while they are
    referenced by active instances, from Robert Shearman.

14) Fix truncated PHY LED trigger names, from Geert Uytterhoeven.

15) Fix a few regressions from virtio_net XDP support, from John
    Fastabend and Jakub Kicinski.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (102 commits)
  ISDN: eicon: silence misleading array-bounds warning
  net: phy: micrel: add support for KSZ8795
  gtp: fix cross netns recv on gtp socket
  gtp: clear DF bit on GTP packet tx
  gtp: add genl family modules alias
  tcp: don't annotate mark on control socket from tcp_v6_send_response()
  ravb: unmap descriptors when freeing rings
  virtio_net: reject XDP programs using header adjustment
  virtio_net: use dev_kfree_skb for small buffer XDP receive
  r8152: check rx after napi is enabled
  r8152: re-schedule napi for tx
  r8152: avoid start_xmit to schedule napi when napi is disabled
  r8152: avoid start_xmit to call napi_schedule during autosuspend
  net: dsa: Bring back device detaching in dsa_slave_suspend()
  net: phy: leds: Fix truncated LED trigger names
  net: phy: leds: Break dependency of phy.h on phy_led_triggers.h
  net: phy: leds: Clear phy_num_led_triggers on failure to avoid crash
  net-next: ethernet: mediatek: change the compatible string
  Documentation: devicetree: change the mediatek ethernet compatible string
  bnxt_en: Fix RTNL lock usage on bnxt_get_port_module_status().
  ...

Pull xfs uodates from Darrick Wong:
 "I have some more fixes this week: better input validation, corruption
  avoidance, build fixes, memory leak fixes, and a couple from Christoph
  to avoid an ENOSPC failure.

  Summary:
   - Fix race conditions in the CoW code
   - Fix some incorrect input validation checks
   - Avoid crashing fs by running out of space when freeing inodes
   - Fix toctou race wrt whether or not an inode has an attr
   - Fix build error on arm
   - Fix page refcount corruption when readahead fails
   - Don't corrupt userspace in the bmap ioctl"

* tag 'xfs-for-linus-4.10-rc6-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: prevent quotacheck from overloading inode lru
  xfs: fix bmv_count confusion w/ shared extents
  xfs: clear _XBF_PAGES from buffers when readahead page
  xfs: extsize hints are not unlikely in xfs_bmap_btalloc
  xfs: remove racy hasattr check from attr ops
  xfs: use per-AG reservations for the finobt
  xfs: only update mount/resv fields on success in __xfs_ag_resv_init
  xfs: verify dirblocklog correctly
  xfs: fix COW writeback race

Pull btrfs updates from Chris Mason:
 "Some fixes that we've collected from the list.

  We still have one more pending to nail down a regression in lzo
  compression, but I wanted to get this batch out the door"

* 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: remove ->{get, set}_acl() from btrfs_dir_ro_inode_operations
  Btrfs: disable xattr operations on subvolume directories
  Btrfs: remove old tree_root case in btrfs_read_locked_inode()
  Btrfs: fix truncate down when no_holes feature is enabled
  Btrfs: Fix deadlock between direct IO and fast fsync
  btrfs: fix false enospc error when truncating heavily reflinked file

Pull block fixes from Jens Axboe:
 "A set of fixes for this series. This contains:

   - Set of fixes for the nvme target code

   - A revert of patch from this merge window, causing a regression with
     WRITE_SAME on iSCSI targets at least.

   - A fix for a use-after-free in the new O_DIRECT bdev code.

   - Two fixes for the xen-blkfront driver"

* 'for-linus' of git://git.kernel.dk/linux-block:
  Revert "sd: remove __data_len hack for WRITE SAME"
  nvme-fc: use blk_rq_nr_phys_segments
  nvmet-rdma: Fix missing dma sync to nvme data structures
  nvmet: Call fatal_error from keep-alive timout expiration
  nvmet: cancel fatal error and flush async work before free controller
  nvmet: delete controllers deletion upon subsystem release
  nvmet_fc: correct logic in disconnect queue LS handling
  block: fix use after free in __blkdev_direct_IO
  xen-blkfront: correct maximum segment accounting
  xen-blkfront: feature flags handling adjustments

Pull rdma fixes from Doug Ledford:
 "Second round of -rc fixes for 4.10.

  This -rc cycle has been slow for the rdma subsystem. I had already
  sent you the first batch before the Holiday break. After that, we kept
  only getting a few here or there. Up until this week, when I got a
  drop of 13 to one driver (qedr). So, here's the -rc patches I have. I
  currently have none held in reserve, so unless something new comes in,
  this is it until the next merge window opens.

  Summary:

   - series of iw_cxgb4 fixes to make it work with the drain cq API

   - one or two patches each to: srp, iser, cxgb3, vmw_pvrdma, umem,
     rxe, and ipoib

   - one big series (13 patches) for the new qedr driver"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (27 commits)
  RDMA/cma: Fix unknown symbol when CONFIG_IPV6 is not enabled
  IB/rxe: Prevent from completer to operate on non valid QP
  IB/rxe: Fix rxe dev insertion to rxe_dev_list
  IB/umem: Release pid in error and ODP flow
  RDMA/qedr: Dispatch port active event from qedr_add
  RDMA/qedr: Fix and simplify memory leak in PD alloc
  RDMA/qedr: Fix RDMA CM loopback
  RDMA/qedr: Fix formatting
  RDMA/qedr: Mark three functions as static
  RDMA/qedr: Don't reset QP when queues aren't flushed
  RDMA/qedr: Don't spam dmesg if QP is in error state
  RDMA/qedr: Remove CQ spinlock from CM completion handlers
  RDMA/qedr: Return max inline data in QP query result
  RDMA/qedr: Return success when not changing QP state
  RDMA/qedr: Add uapi header qedr-abi.h
  RDMA/qedr: Fix MTU returned from QP query
  RDMA/core: Add the function ib_mtu_int_to_enum
  IB/vmw_pvrdma: Fix incorrect cleanup on pvrdma_pci_probe error path
  IB/vmw_pvrdma: Don't leak info from alloc_ucontext
  IB/cxgb3: fix misspelling in header guard
  ...

Pull s390 fixes from Martin Schwidefsky:
 "Another two bug fixes:

   - ptrace partial write information leak

   - a guest page hinting regression introduced with v4.6"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/mm: Fix cmma unused transfer from pgste into pte
  s390/ptrace: Preserve previous registers for short regset write

Merge branch 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb

Pull swiotlb fix from Konrad Rzeszutek Wilk:
 "An ARM fix in the Xen SWIOTLB - mainly the translation of physical to
  bus addresses was done just a tad too late"

* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb-xen: update dev_addr after swapping pages

Pull VFIO fix from Alex Williamson:
 "mdev IOMMU groups are not yet compatible with the powerpc SPAPR IOMMU
  backend, detect and fail group attach (Greg Kurz)"

* tag 'vfio-v4.10-rc6' of git://github.com/awilliam/linux-vfio:
  vfio/spapr: fail tce_iommu_attach_group() when iommu_data is null

If IPV6 has not been enabled in the underlying kernel, we must avoid
calling IPV6 procedures in rdma_cm.ko.

This requires using "IS_ENABLED(CONFIG_IPV6)" in "if" statements
surrounding any code which calls external IPV6 procedures.

In the instance fixed here, procedure cma_bind_addr() called
ipv6_addr_type() -- which resulted in calling external procedure
__ipv6_addr_type().

Fixes: 6c26a771 ("RDMA/cma: fix IPv6 address resolution")
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Merge branch 'stable/for-jens-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus

Konrad writes:

Please pull in your 'for-linus' branch two little fixes for Xen
block front:

One fix is for handling the XEN_PAGE_SIZE != PAGE_SIZE (4KB vs 64KB
on ARM for example) mishandling while the other is fixing
the accounting for the configuration changes.

Pull media fixes from Mauro Carvalho Chehab:

 - fix a regression on tvp5150 causing failures at input selection and
   image glitches

 - CEC was moved out of staging for v4.10. Fix some bugs on it while not
   too late

 - fix a regression on pctv452e caused by VM stack changes

 - fix suspend issued with smiapp

 - fix a regression on cobalt driver

 - fix some warnings and Kconfig issues with some random configs.

* tag 'media/v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] s5k4ecgx: select CRC32 helper
  [media] dvb: avoid warning in dvb_net
  [media] v4l: tvp5150: Don't override output pinmuxing at stream on/off time
  [media] v4l: tvp5150: Fix comment regarding output pin muxing
  [media] v4l: tvp5150: Reset device at probe time, not in get/set format handlers
  [media] pctv452e: move buffer to heap, no mutex
  [media] media/cobalt: use pci_irq_allocate_vectors
  [media] cec: fix race between configuring and unconfiguring
  [media] cec: move cec_report_phys_addr into cec_config_thread_func
  [media] cec: replace cec_report_features by cec_fill_msg_report_features
  [media] cec: update log_addr[] before finishing configuration
  [media] cec: CEC_MSG_GIVE_FEATURES should abort for CEC version < 2
  [media] cec: when canceling a message, don't overwrite old status info
  [media] cec: fix report_current_latency
  [media] smiapp: Make suspend and resume functions __maybe_unused
  [media] smiapp: Implement power-on and power-off sequences without runtime PM

Pull MMC fix from Ulf Hansson:
 "MMC host: fix runtime PM resume path in dw_mmc"

* tag 'mmc-v4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: dw_mmc: force setup bus if active slots exist

Pull thermal management fix from Zhang Rui:
 "A single revert from a recently introduced problem.

  Specifics:

  Commit 7611fb68 ("thermal: thermal_hwmon: Convert to
  hwmon_device_register_with_info()"), which was introduced in 4.10-rc5,
  uses new hwmon API. But this breaks some soc thermal driver because
  the new hwmon API has a strict rule for the hwmon device name. Revert
  the offending commit as a quick solution for 4.10"

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  Revert "thermal: thermal_hwmon: Convert to hwmon_device_register_with_info()"

Quotacheck runs at mount time in situations where quota accounting must
be recalculated. In doing so, it uses bulkstat to visit every inode in
the filesystem. Historically, every inode processed during quotacheck
was released and immediately tagged for reclaim because quotacheck runs
before the superblock is marked active by the VFS. In other words,
the final iput() lead to an immediate ->destroy_inode() call, which
allowed the XFS background reclaim worker to start reclaiming inodes.

Commit 17c12bcd ("xfs: when replaying bmap operations, don't let
unlinked inodes get reaped") marks the XFS superblock active sooner as
part of the mount process to support caching inodes processed during log
recovery. This occurs before quotacheck and thus means all inodes
processed by quotacheck are inserted to the LRU on release.  The
s_umount lock is held until the mount has completed and thus prevents
the shrinkers from operating on the sb. This means that quotacheck can
excessively populate the inode LRU and lead to OOM conditions on systems
without sufficient RAM.

Update the quotacheck bulkstat handler to set XFS_IGET_DONTCACHE on
inodes processed by quotacheck. This causes ->drop_inode() to return 1
and in turn causes iput_final() to evict the inode. This preserves the
original quotacheck behavior and prevents it from overloading the LRU
and running out of memory.

CC: stable@vger.kernel.org # v4.9
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>

Slava Shwartsman reported a warning in skb_try_coalesce(), when we
detect skb->truesize is completely wrong.

In his case, issue came from IPv6 reassembly coping with malicious
datagrams, that forced various pskb_may_pull() to reallocate a bigger
skb->head than the one allocated by NIC driver before entering GRO
layer.

Current code does not change skb->truesize, leaving this burden to
callers if they care enough.

Blindly changing skb->truesize in pskb_expand_head() is not
easy, as some producers might track skb->truesize, for example
in xmit path for back pressure feedback (sk->sk_wmem_alloc)

We can detect the cases where it should be safe to change
skb->truesize :

1) skb is not attached to a socket.
2) If it is attached to a socket, destructor is sock_edemux()

My audit gave only two callers doing their own skb->truesize
manipulation.

I had to remove skb parameter in sock_edemux macro when
CONFIG_INET is not set to avoid a compile error.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: encapsulated filters

This series adds support for setting up filters for encapsulated traffic on
SFC 8000-series adapters, which recognise VXLAN, GENEVE and NVGRE packets by
parsing packet headers.  (VXLAN and GENEVE will only be recognised if the
driver on the primary PF has notified the firmware of relevant UDP ports,
which this driver does not yet do.)
While the driver currently has no way of using these filters for flow
steering, it is nonetheless necessary to insert catch-all (aka 'default')
filters to direct this traffic, similar to the existing unencapsulated uni-
and multi-cast catch-all filters, as otherwise the traffic will be dropped
by the NIC - implementation details of the hardware filtering mean that the
traffic will not get matched on outer MAC address to unencapsulated catch-
all filters.  (Yes, this is a mess.)
Although this is, therefore, fixing a bug in the existing driver, it's a bug
which has existed since 8000 series support was added, and the fix involves
quite a big patch with an 'adding features' flavour to it, hence why this is
for net-next rather than net and stable.

v2: move netif_cond_dbg into netdevice.h and its own patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

8000 series adapters support filtering VXLAN, NVGRE and GENEVE traffic
 based on inner fields, and when the NIC recognises such traffic, it
 does not match unencapsulated traffic filters any more.  So add catch-
 all filters for encapsulated traffic on supporting platforms.
Although recognition of VXLAN and GENEVE is based on UDP ports, and thus
 will not occur until the driver (on the primary PF) notifies the
 firmware of UDP ports to use, NVGRE will always be recognised, hence
 without this patch 8000 series adapters will drop all NVGRE traffic.

Partly based on patches by Jon Cooper <jcooper@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rationalise several debug-or-warnings printks using netif_cond_dbg
 to make output more consistent.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For reporting things that may or may not be serious, depending on some
 condition, netif_cond_dbg will check the condition and print the report
 at either dbg (if the condition is true) or the specified level.
Suggested-by: Jon Cooper <jcooper@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the NIC is switched from full-featured to low-latency, encapsulated
 filters are no longer available, and this causes errors. This patch
 removes those filters from the filter table on restore.
Also, if filters which are removed by the above, or which we fail to
 insert when restoring filters, were UC, MC or broadcast default
 filters, invalidate the corresponding vlan->default_filters entry.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The stats member of struct frad_locl is used neither by the dlci nor the
sdla driver, so it might as well be removed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling delay skew and GTXCLK
bits.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

With some gcc versions, we get a warning about the eicon driver,
and that currently shows up as the only remaining warning in one
of the build bots:

In file included from ../drivers/isdn/hardware/eicon/message.c:30:0:
eicon/message.c: In function 'mixer_notify_update':
eicon/platform.h:333:18: warning: array subscript is above array bounds [-Warray-bounds]

The code is easily changed to open-code the unusual PUT_WORD() line
causing this to avoid the warning.

Cc: stable@vger.kernel.org
Link: http://arm-soc.lixom.net/buildlogs/stable-rc/v4.4.45/Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-4.11-20170124' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2017-01-24

this is a pull request of 4 patches for net-next/master.

The first patch by Oliver Hartkopp adds a netlink API to configure the
interface termination of a CAN card. The next two patches are by me and
add a netlink API to query and configure CAN interfaces that only
support fixed bitrates. The last patch by Colin Ian King simplifies the
return path in the softing_cs driver's softingcs_probe() function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is adds support for the PHYs in the KSZ8795 5port managed switch.

It will allow to detect the link between the switch and the soc
and uses the same read_status functions as the KSZ8873MLL switch.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andreas Schultz says:

====================
various gtp fixes

I'm sorry for the compile error mess up in the last version.
It's no excuse for not test compiling, but the hunks got lost in
a rebase.

This is the part of the previous "simple gtp improvements" series
that Pablo indicated should go into net.

The addition of the module alias fixes genl family autoloading,
clearing the DF bit fixes a protocol violation in regard to the
specification and the netns comparison fixes a corner case of
cross netns recv.

v2->v3: fix compiler error introduced in rebase
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The use of the passed through netlink src_net to check for a
cross netns operation was wrong. Using the GTP socket and the
GTP netdevice is always correct (even if the netdev has been
moved to new netns after link creation).

Remove the now obsolete net field from gtp_dev.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>