The vc4 HDMI driver has multiple path shared between the CEC, ALSA and
KMS frameworks, plus two interrupt handlers (CEC and hotplug) that will
read and modify a number of registers.

Even though not bug has been reported so far, it's definitely unsafe, so
let's just add a spinlock to protect the register access of the HDMI
controller.

Link: https://lore.kernel.org/r/20211025141113.702757-5-maxime@cerno.tech
Fixes: c8b75bca ("drm/vc4: Add KMS support for Raspberry Pi.")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.

In VC4, a number of users of that pointers have crept in over the years,
and the previous commits removed them all but the HVS channel a CRTC has
been assigned.

Let's move this channel in struct vc4_crtc at atomic_begin() time, drop
it from our private state structure, and remove our use of crtc->state
from our vblank handler entirely.

Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Link: https://lore.kernel.org/r/20211025141113.702757-4-maxime@cerno.tech
Fixes: 87ebcd42 ("drm/vc4: crtc: Assign output to channel automatically")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

In some situation, we can end up being stuck on a non-blocking that went
through properly.

The situation that seems to trigger it reliably is to first start a
non-blocking commit, and then right after, and before we had any vblank
interrupt), start a blocking commit.

This will lead to the first commit workqueue to be scheduled, setup the
display, while the second commit is waiting for the first one to be
completed.

The vblank interrupt will then be raised, vc4_crtc_handle_vblank() will
run and will compare the active dlist in the HVS channel to the one
associated with the crtc->state.

However, at that point, the second commit is waiting using
drm_atomic_helper_wait_for_dependencies that occurs after
drm_atomic_helper_swap_state has been called, so crtc->state points to
the second commit state. vc4_crtc_handle_vblank() will compare the two
dlist addresses and since they don't match will ignore the interrupt.

The vblank event will never be reported, and the first and second commit
will wait for the first commit completion until they timeout.

The underlying reason is that it was never safe to do so. Indeed,
accessing the ->state pointer access synchronization is based on
ownership guarantees that can only occur within the functions and hooks
defined as part of the KMS framework, and obviously the irq handler
isn't one of them. The rework to move to generic helpers only uncovered
the underlying issue.

However, since the code path between
drm_atomic_helper_wait_for_dependencies() and
drm_atomic_helper_wait_for_vblanks() is serialised and we can't get two
commits in that path at the same time, we can work around this issue by
setting a variable associated to struct drm_crtc to the dlist we expect,
and then using it from the vc4_crtc_handle_vblank() function.

Since that state is shared with the modesetting path, we also need to
introduce a spinlock to protect the code shared between the interrupt
handler and the modesetting path, protecting only our new variable for
now.

Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Link: https://lore.kernel.org/r/20211025141113.702757-3-maxime@cerno.tech
Fixes: 56d1fe09 ("drm/vc4: Make pageflip completion handling more robust.")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.

In VC4, a number of users of that pointers have crept in over the years,
the first one being whether or not the downstream controller of the
pixelvalve is our writeback controller.

Fortunately for us, Since commit 39fcb280 ("drm/vc4: txp: Turn the
TXP into a CRTC of its own") this is no longer something that can change
from one commit to the other and is hardcoded.

Let's set this flag in struct vc4_crtc if we happen to be the TXP, and
drop the flag from our private state structure.

Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Link: https://lore.kernel.org/r/20211025141113.702757-2-maxime@cerno.tech
Fixes: 008095e0 ("drm/vc4: Add support for the transposer block")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Prior to commit 6c836d96 ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
started using the blocking variant, for a variety of reasons -- quoting
Sean Paul's potentially-faulty memory:

"""
 - To avoid racing a subsequent PSR entry (if exit takes a long time)
 - To avoid racing disable/modeset
 - We're not displaying new content while exiting PSR anyways, so there
   is minimal utility in allowing frames to be submitted
 - We're lying to userspace telling them frames are on the screen when
   we're just dropping them on the floor
"""

However, I'm finding that this blocking transition is causing upwards of
60+ ms of unneeded latency on PSR-exit, to the point that initial cursor
movements when leaving PSR are unbearably jumpy.

It turns out that we need to meet in the middle somewhere: Sean is right
that we were "lying to userspace" with a non-blocking PSR-exit, but the
new blocking behavior is also waiting too long:

According to the eDP specification, the sink device must support PSR
entry transitions from both state 4 (ACTIVE_RESYNC) and state 0
(INACTIVE). It also states that in ACTIVE_RESYNC, "the Sink device must
display the incoming active frames from the Source device with no
visible glitches and/or artifacts."

Thus, for our purposes, we only need to wait for ACTIVE_RESYNC before
moving on; we are ready to display video, and subsequent PSR-entry is
safe.

Tested on a Samsung Chromebook Plus (i.e., Rockchip RK3399 Gru Kevin),
where this saves about 60ms of latency, for PSR-exit that used to
take about 80ms.

Fixes: 6c836d96 ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103135112.v3.1.I67612ea073c3306c71b46a87be894f79707082df@changeid

Add audio HDMI codec function support, enable it through device true
flag "analogix,audio-enable".
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211104033857.2634562-1-xji@analogixsemi.com

The basic anx7625 driver only support MIPI DSI rx signal input.
This patch add MIPI DPI rx input configuration support, after apply
this patch, the driver can support DSI rx or DPI rx by adding
'bus-type' in DT.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211104033639.2634502-1-xji@analogixsemi.com

At some time, the original code may return non zero value, force return 0
if operation finished.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211104033609.2634452-1-xji@analogixsemi.com

Add 'bus-type' and 'data-lanes' define for port0. Add DP tx lane0,
lane1 swing register setting array, and audio enable flag.

The device which cannot pass DP tx PHY CTS caused by long PCB trace or
embedded MUX, adjusting ANX7625 PHY parameters can pass the CTS test. The
adjusting type include Pre-emphasis, Vp-p, Rterm(Resistor Termination)
and Rsel(Driven Strength). Each lane has maximum 20 registers for
these settings.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211104033444.2634397-1-xji@analogixsemi.com

Depending on a given HVS output (HVS to PixelValves) and input (planes
attached to a channel) load, the HVS needs for the core clock to be
raised above its boot time default.

Failing to do so will result in a vblank timeout and a stalled display
pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-11-maxime@cerno.tech

If we have a state already and disconnect/reconnect the display, the
SCDC messages won't be sent again since we didn't go through a disable /
enable cycle.

In order to fix this, let's call the vc4_hdmi_enable_scrambling function
in the detect callback if there is a mode and it needs the scrambler to
be enabled.

Fixes: c85695a2 ("drm/vc4: hdmi: Enable the scrambler")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-10-maxime@cerno.tech

Now that we have the infrastructure in place, we can raise the maximum
pixel rate we can reach for HDMI0 on the BCM2711.

HDMI1 is left untouched since its pixelvalve has a smaller FIFO and
would need a clock faster than what we can provide to support the same
modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211025152903.1088803-9-maxime@cerno.tech

The load tracker was initially designed to report and warn about a load
too high for the HVS. To do so, it computes for each plane the impact
it's going to have on the HVS, and will warn (if it's enabled) if we go
over what the hardware can process.

While the limits being used are a bit irrelevant to the BCM2711, the
algorithm to compute the HVS load will be one component used in order to
compute the core clock rate on the BCM2711.

Let's remove the hooks to prevent the load tracker to do its
computation, but since we don't have the same limits, don't check them
against them, and prevent the debugfs file to enable it from being
created.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-8-maxime@cerno.tech

The encoder retrieval code has been a source of bugs and glitches in the
past and the crtc <-> encoder association been wrong in a number of
different ways.

Add some logging to quickly spot issues if they occur.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-7-maxime@cerno.tech

It turns out the encoder retrieval code, in addition to being
unnecessarily complicated, has a bug when only the planes and crtcs are
affected by a given atomic commit.

Indeed, in such a case, either drm_atomic_get_old_connector_state or
drm_atomic_get_new_connector_state will return NULL and thus our encoder
retrieval code will not match on anything.

We can however simplify the code by using drm_for_each_encoder_mask, the
drm_crtc_state storing the encoders a given CRTC is connected to
directly and without relying on any other state.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-6-maxime@cerno.tech

vc4_crtc_config_pv() retrieves the encoder again, even though its only
caller, vc4_crtc_atomic_enable(), already did.

Pass the encoder pointer as an argument instead of going through all the
connectors to retrieve it again.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-5-maxime@cerno.tech

We'll need that function in vc4_kms to compute the core clock rate
requirements.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-4-maxime@cerno.tech

Prior to commit 6800234c ("drm/vc4: hdmi: Convert to gpiod"), in the
detect hook, if we had an HPD GPIO we would only rely on it and return
whatever state it was in.

However, that commit changed that by mistake to only consider the case
where we have a GPIO and it returns a logical high, and would fall back
to the other methods otherwise.

Since we can read the EDIDs when the HPD signal is low on some displays,
we changed the detection status from disconnected to connected, and we
would ignore an HPD pulse.

Fixes: 6800234c ("drm/vc4: hdmi: Convert to gpiod")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-3-maxime@cerno.tech

Commit 9d44abbb ("drm/vc4: Fall back to using an EDID probe in the
absence of a GPIO.") added some code to read the EDID through DDC in the
HDMI driver detect hook since the Pi3 had no HPD GPIO back then.
However, commit b1b8f45b ("ARM: dts: bcm2837: Add missing GPIOs of
Expander") changed that a couple of years later.

This causes an issue though since some TV (like the LG 55C8) when it
comes out of standy will deassert the HPD line, but the EDID will
remain readable.

It causes an issues nn platforms without an HPD GPIO, like the Pi4,
where the DDC probing will be our primary mean to detect a display, and
thus we will never detect the HPD pulse. This was fine before since the
pulse was small enough that we would never detect it, and we also didn't
have anything (like the scrambler) that needed to be set up in the
display.

However, now that we have both, the display during the HPD pulse will
clear its scrambler status, and since we won't detect the
disconnect/reconnect cycle we will never enable the scrambler back.

As our main reason for that DDC probing is gone, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-2-maxime@cerno.tech

Don't touch the exclusive fence manually here, but rather use the
general dma_resv function. We did that for better hw reset handling but
this doesn't necessary work correctly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deuche <alexander.deucher@amd.com>
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028132630.2330-6-christian.koenig@amd.com

Just grab all fences in one go.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028132630.2330-3-christian.koenig@amd.com

When link-status changes, send a hotplug uevent which contains the
connector ID. That way, user-space can more easily figure out that
only this connector has been updated.

Changes in v4: avoid sending two uevents (Ville)
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018084707.32253-7-contact@emersion.fr

If an hotplug event only updates a single connector, use
drm_kms_helper_connector_hotplug_event instead of
drm_kms_helper_hotplug_event.

Changes in v4:
- Simplify loop logic (Ville, Sam)
- Update drm_connector_helper_hpd_irq_event (Maxime)
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018084707.32253-6-contact@emersion.fr

When updating a single connector, use
drm_kms_helper_connector_hotplug_event instead of
drm_kms_helper_hotplug_event.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018084707.32253-5-contact@emersion.fr

In drm_connector_register, use drm_sysfs_connector_hotplug_event
instead of drm_sysfs_hotplug_event, because the hotplug event
only updates a single connector.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018084707.32253-4-contact@emersion.fr

This function is the same as drm_kms_helper_hotplug_event, but takes
a connector instead of a device.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018084707.32253-3-contact@emersion.fr

This function sends a hotplug uevent with a CONNECTOR property.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018084707.32253-2-contact@emersion.fr

Probelm:
Singlaning one sched fence from within another's sched
fence singal callback generates lockdep splat because
the both have same lockdep class of their fence->lock

Fix:
Fix bellow stack by rescheduling to irq work of
signaling and killing of jobs that left when entity is killed.

[11176.741181]  dump_stack+0x10/0x12
[11176.741186] __lock_acquire.cold+0x208/0x2df
[11176.741197]  lock_acquire+0xc6/0x2d0
[11176.741204]  ? dma_fence_signal+0x28/0x80
[11176.741212] _raw_spin_lock_irqsave+0x4d/0x70
[11176.741219]  ? dma_fence_signal+0x28/0x80
[11176.741225]  dma_fence_signal+0x28/0x80
[11176.741230] drm_sched_fence_finished+0x12/0x20 [gpu_sched]
[11176.741240] drm_sched_entity_kill_jobs_cb+0x1c/0x50 [gpu_sched]
[11176.741248] dma_fence_signal_timestamp_locked+0xac/0x1a0
[11176.741254]  dma_fence_signal+0x3b/0x80
[11176.741260] drm_sched_fence_finished+0x12/0x20 [gpu_sched]
[11176.741268] drm_sched_job_done.isra.0+0x7f/0x1a0 [gpu_sched]
[11176.741277] drm_sched_job_done_cb+0x12/0x20 [gpu_sched]
[11176.741284] dma_fence_signal_timestamp_locked+0xac/0x1a0
[11176.741290]  dma_fence_signal+0x3b/0x80
[11176.741296] amdgpu_fence_process+0xd1/0x140 [amdgpu]
[11176.741504] sdma_v4_0_process_trap_irq+0x8c/0xb0 [amdgpu]
[11176.741731]  amdgpu_irq_dispatch+0xce/0x250 [amdgpu]
[11176.741954]  amdgpu_ih_process+0x81/0x100 [amdgpu]
[11176.742174]  amdgpu_irq_handler+0x26/0xa0 [amdgpu]
[11176.742393] __handle_irq_event_percpu+0x4f/0x2c0
[11176.742402] handle_irq_event_percpu+0x33/0x80
[11176.742408]  handle_irq_event+0x39/0x60
[11176.742414]  handle_edge_irq+0x93/0x1d0
[11176.742419]  __common_interrupt+0x50/0xe0
[11176.742426]  common_interrupt+0x80/0x90
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Suggested-by: Daniel Vetter  <daniel.vetter@ffwll.ch>
Suggested-by: Christian König <christian.koenig@amd.com>
Tested-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://www.spinics.net/lists/dri-devel/msg321250.html

Commit 1bdb542d ("drm/ingenic: Simplify code by using hwdescs
array") caused the dma_hwdesc_phys_f{0,1} variables to be used while
uninitialized in a mmio register write, which most certainly broke the
ingenic-drm driver.

However, the very same patchset also submitted commit 60554662
("drm/ingenic: Upload palette before frame"), which restored a correct
behaviour by doing the register writes in a different place in the code.

What's left of this, is just to remove the bogus register writes in the
probe function.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211030100032.42066-1-paul@crapouillou.netAcked-by: Sam Ravnborg <sam@ravnborg.org>

Attach a top-level bridge to each encoder, which will be used for
negociating the bus format and flags.

All the bridges are now attached with DRM_BRIDGE_ATTACH_NO_CONNECTOR.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026181240.213806-7-paul@crapouillou.netTested-by: Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Christophe Branchereau <cbranchereau@gmail.com>

When using C8 color mode, make sure that the palette is always uploaded
before a frame; otherwise the very first frame will have wrong colors.

Do that by changing the link order of the DMA descriptors.

v3: Fix ingenic_drm_get_new_priv_state() called instead of
    ingenic_drm_get_priv_state()
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026181240.213806-6-paul@crapouillou.netTested-by: Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Christophe Branchereau <cbranchereau@gmail.com>

Setting the DMA descriptor chain register in the probe function has been
fine until now, because we only ever had one descriptor per foreground.

As the driver will soon have real descriptor chains, and the DMA
descriptor chain register updates itself to point to the current
descriptor being processed, this register needs to be reset after a full
modeset to point to the first descriptor of the chain.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026181240.213806-5-paul@crapouillou.netTested-by: Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Christophe Branchereau <cbranchereau@gmail.com>

The IPU scaling information is computed in the plane's ".atomic_check"
callback, and used in the ".atomic_update" callback. As such, it is
state-specific, and should be moved to a private state structure.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026181240.213806-4-paul@crapouillou.netTested-by: Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Christophe Branchereau <cbranchereau@gmail.com>

Until now, the ingenic-drm as well as the ingenic-ipu drivers used to
put state-specific information in their respective private structure.

Add boilerplate code to support private objects in the two drivers, so
that state-specific information can be put in the state-specific private
structure.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026181240.213806-3-paul@crapouillou.netTested-by: Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Christophe Branchereau <cbranchereau@gmail.com>

Instead of having one 'hwdesc' variable for the plane #0, one for the
plane #1 and one for the palette, use a 'hwdesc[3]' array, where the
DMA hardware descriptors are indexed by the plane's number.

v2: dma_hwdesc_addr() extended to support palette hwdesc. The palette
    hwdesc is now hwdesc[3] to simplify things. Add
    ingenic_drm_configure_hwdesc*() functions to factorize code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026181240.213806-2-paul@crapouillou.netTested-by: Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Christophe Branchereau <cbranchereau@gmail.com>

Today's -next fails building arm64 defconfig as follows:

ERROR: modpost: module drm_cma_helper uses symbol dma_buf_vunmap from
 namespace DMA_BUF, but does not import it.
ERROR: modpost: module drm_cma_helper uses symbol dma_buf_vmap from
 namespace DMA_BUF, but does not import it.

Fix this by importing DMA_BUF namespace into drm_cma_helper.ko. Also
fix the problem with drm_shmem_helper.ko.
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Fixes: 4b2b5e14 ("drm: Move GEM memory managers into modules")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211027212506.3418521-1-marcel@ziswiler.com

Makes the handling a bit more complex, but avoids the use of
dma_resv_get_excl_unlocked().
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005113742.1101-27-christian.koenig@amd.com

The left shift of unsigned int 32 bit integer constant 1 is evaluated
using 32 bit arithmetic and then assigned to a signed 64 bit integer.
In the case where value is 32 or more this can lead to an overflow
(value can be in range 0..MAX_CAPSET_ID (63). Fix this by shifting
the value 1ULL instead.

Addresses-Coverity: ("Uninitentional integer overflow")
Fixes: 4fb530e5 ("drm/virtio: implement context init: support init ioctl")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210930102748.16922-1-colin.king@canonical.comSigned-off-by: Gerd Hoffmann <kraxel@redhat.com>

The left shift of unsigned int 32 bit integer constant 1 is evaluated
using 32 bit arithmetic and then assigned to a signed 64 bit integer.
In the case where i is 32 or more this can lead to an overflow. Fix
this by shifting the value 1ULL instead.

Addresses-Coverity: ("Uninitentional integer overflow")
Fixes: 8d6b006e ("drm/virtio: implement context init: handle VIRTGPU_CONTEXT_PARAM_POLL_RINGS_MASK")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210930101941.16546-1-colin.king@canonical.comSigned-off-by: Gerd Hoffmann <kraxel@redhat.com>

Add Gurchetan Singh and me as reviewers for virtio-gpu.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Acked-by: Gurchetan Singh <gurchetansingh@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20211028213446.955338-1-olvaffe@gmail.comSigned-off-by: Gerd Hoffmann <kraxel@redhat.com>