- 04 May, 2016 34 commits
-
-
Fabio Estevam authored
commit 33b96d2c upstream. Currently we have an incorrect behaviour when multiple devices are present under the weim node. For example: &weim { ... status = "okay"; sram@0,0 { ... status = "okay"; }; mram@0,0 { ... status = "disabled"; }; }; In this case only the 'sram' device should be probed and not 'mram'. However what happens currently is that the status variable is ignored, causing the 'sram' device to be disabled and 'mram' to be enabled. Change the weim_parse_dt() function to use for_each_available_child_of_node()so that the devices marked with 'status = disabled' are not probed. Suggested-by:
Wolfgang Netbal <wolfgang.netbal@sigmatek.at> Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by:
Sascha Hauer <s.hauer@pengutronix.de> Acked-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pali Rohár authored
commit 98f42221 upstream. Based on CPU type choose generic omap3 or omap3430 specific cpuidle parameters. Parameters for omap3430 were measured on Nokia N900 device and added by commit 5a1b1d3a ("OMAP3: RX-51: Pass cpu idle parameters") which were later removed by commit 231900af ("ARM: OMAP3: cpuidle - remove rx51 cpuidle parameters table") due to huge code complexity. This patch brings cpuidle parameters for omap3430 devices again, but uses simple condition based on CPU type. Fixes: 231900af ("ARM: OMAP3: cpuidle - remove rx51 cpuidle parameters table") Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Borislav Petkov authored
commit f594bae0 upstream. I'm surprised this remained undocumented since at least 2011. And it is actually a very useful switch, as Steve and I came to realize recently. Add the text from 2cba3ffb ("perf stat: Add -d -d and -d -d -d options to show more CPU events") which added the incrementing aspect to -d. Tested-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Vitaly Kuznetsov authored
commit e513229b upstream. When an SMP Hyper-V guest is running on top of 2012R2 Server and secondary cpus are sent offline (with echo 0 > /sys/devices/system/cpu/cpu$cpu/online) the system freeze is observed. This happens due to the fact that on newer hypervisors (Win8, WS2012R2, ...) vmbus channel handlers are distributed across all cpus (see init_vp_index() function in drivers/hv/channel_mgmt.c) and on cpu offlining nobody reassigns them to CPU0. Prevent cpu offlining when vmbus is loaded until the issue is fixed host-side. This patch also disables hibernation but it is OK as it is also broken (MCE error is hit on resume). Suspend still works. Tested with WS2008R2 and WS2012R2. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> [ 3chas3@gmail.com: rebase to 3.14-stable ] Signed-off-by:
Chas Williams <3chas3@gmail.com> Signed-off-by:
-
Vasily Kulikov authored
commit 8a5e5e02 upstream. Poison pointer values should be small enough to find a room in non-mmap'able/hardly-mmap'able space. E.g. on x86 "poison pointer space" is located starting from 0x0. Given unprivileged users cannot mmap anything below mmap_min_addr, it should be safe to use poison pointers lower than mmap_min_addr. The current poison pointer values of LIST_POISON{1,2} might be too big for mmap_min_addr values equal or less than 1 MB (common case, e.g. Ubuntu uses only 0x10000). There is little point to use such a big value given the "poison pointer space" below 1 MB is not yet exhausted. Changing it to a smaller value solves the problem for small mmap_min_addr setups. The values are suggested by Solar Designer: http://www.openwall.com/lists/oss-security/2015/05/02/6Signed-off-by:
Vasily Kulikov <segoon@openwall.com> Cc: Solar Designer <solar@openwall.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Geert Uytterhoeven authored
commit ff1cab37 upstream. The BSP team noticed that there is spin/mutex lock issue on sh-sci when CPUFREQ is used. The issue is that the notifier function may call mutex_lock() while the spinlock is held, which can lead to a BUG(). This may happen if CPUFREQ is changed while another CPU calls clk_get_rate(). Taking the spinlock was added to the notifier function in commit e552de24 ("sh-sci: add platform device private data"), to protect the list of serial ports against modification during traversal. At that time the Common Clock Framework didn't exist yet, and clk_get_rate() just returned clk->rate without taking a mutex. Note that since commit d535a230 ("serial: sh-sci: Require a device per port mapping."), there's no longer a list of serial ports to traverse, and taking the spinlock became superfluous. To fix the issue, just remove the cpufreq notifier: 1. The notifier doesn't work correctly: all it does is update stored clock rates; it does not update the divider in the hardware. The divider will only be updated when calling sci_set_termios(). I believe this was broken back in 2004, when the old drivers/char/sh-sci.c driver (where the notifier did update the divider) was replaced by drivers/serial/sh-sci.c (where the notifier just updated port->uartclk). Cfr. full-history-linux commits 6f8deaef2e9675d9 ("[PATCH] sh: port sh-sci driver to the new API") and 3f73fe878dc9210a ("[PATCH] Remove old sh-sci driver"). 2. On modern SoCs, the sh-sci parent clock rate is no longer related to the CPU clock rate anyway, so using a cpufreq notifier is futile. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Eryu Guan authored
commit 5e1021f2 upstream. ext4_reserve_inode_write() in ext4_mark_inode_dirty() could fail on error (e.g. EIO) and iloc.bh can be NULL in this case. But the error is ignored in the following "if" condition and ext4_expand_extra_isize() might be called with NULL iloc.bh set, which triggers NULL pointer dereference. This is uncovered by commit 8b4953e1 ("ext4: reserve code points for the project quota feature"), which enlarges the ext4_inode size, and run the following script on new kernel but with old mke2fs: #/bin/bash mnt=/mnt/ext4 devname=ext4-error dev=/dev/mapper/$devname fsimg=/home/fs.img trap cleanup 0 1 2 3 9 15 cleanup() { umount $mnt >/dev/null 2>&1 dmsetup remove $devname losetup -d $backend_dev rm -f $fsimg exit 0 } rm -f $fsimg fallocate -l 1g $fsimg backend_dev=`losetup -f --show $fsimg` devsize=`blockdev --getsz $backend_dev` good_tab="0 $devsize linear $backend_dev 0" error_tab="0 $devsize error $backend_dev 0" dmsetup create $devname --table "$good_tab" mkfs -t ext4 $dev mount -t ext4 -o errors=continue,strictatime $dev $mnt dmsetup load $devname --table "$error_tab" && dmsetup resume $devname echo 3 > /proc/sys/vm/drop_caches ls -l $mnt exit 0 [ Patch changed to simplify the function a tiny bit. -- Ted ] Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Cc: Jan Kara <jack@suse.cz> Signed-off-by:
-
Michael Hennerich authored
commit f3df53e4 upstream. Fix RDAC read back errors caused by a typo. Value must shift by 2. Fixes: a4bd3949 ("drivers/misc/ad525x_dpot.c: new features") Signed-off-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit a25f4a95 upstream. drivers/rtc/rtc-vr41xx.c:229: warning: ‘vr41xx_rtc_alarm_irq_enable’ defined but not used Apparently the conversion to alarm_irq_enable forgot to wire up the callback. Fixes: 16380c15 ("RTC: Convert rtc drivers to use the alarm_irq_enable method") Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Alexander Kochetkov authored
commit d5861262 upstream. Year field must be in BCD format, according to hym8563 datasheet. Due to the bug year 2016 became 2010. Fixes: dcaf0384 ("rtc: add hym8563 rtc-driver") Signed-off-by:
Alexander Kochetkov <al.kochet@gmail.com> Signed-off-by:
-
Ben Hutchings authored
commit 50e6315d upstream. Commit 985087db 'misc: add support for bmp18x chips to the bmp085 driver' changed the BMP085 config symbol to a boolean. I see no reason why the shared code cannot be built as a module, so change it back to tristate. Fixes: 985087db ("misc: add support for bmp18x chips to the bmp085 driver") Cc: Eric Andersson <eric.andersson@unixphere.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Sushaanth Srirangapathi authored
commit 713fced8 upstream. Commit 028cd86b ("video: da8xx-fb: fix the polarities of the hsync/vsync pulse") fixes polarities of HSYNC/VSYNC pulse but forgot to update known_lcd_panels[] which had sync values according to old logic. This breaks LCD at least on DA850 EVM. This patch fixes this issue and I have tested this for panel "Sharp_LK043T1DG01" using DA850 EVM board. Fixes: 028cd86b ("video: da8xx-fb: fix the polarities of the hsync/vsync pulse") Signed-off-by:
Sushaanth Srirangapathi <sushaanth.s@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Arnd Bergmann authored
commit dec63a4d upstream. gcc-6.0 found an ancient bug in the paride driver, which had a "module_param(verbose, bool, 0);" since before 2.6.12, but actually uses it to accept '0', '1' or '2' as arguments: drivers/block/paride/pd.c: In function 'pd_init_dev_parms': drivers/block/paride/pd.c:298:29: warning: comparison of constant '1' with boolean expression is always false [-Wbool-compare] #define DBMSG(msg) ((verbose>1)?(msg):NULL) In 2012, Rusty did a cleanup patch that also changed the type of the variable to 'bool', which introduced what is now a gcc warning. This changes the type back to 'int' and adapts the module_param() line instead, so it should work as documented in case anyone ever cares about running the ancient driver with debugging. Fixes: 90ab5ee9 ("module_param: make bool parameters really bool (drivers & misc)") Signed-off-by:
-
Ignat Korchagin authored
commit b348d7dd upstream. Fix potential out-of-bounds write to urb->transfer_buffer usbip handles network communication directly in the kernel. When receiving a packet from its peer, usbip code parses headers according to protocol. As part of this parsing urb->actual_length is filled. Since the input for urb->actual_length comes from the network, it should be treated as untrusted. Any entity controlling the network may put any value in the input and the preallocated urb->transfer_buffer may not be large enough to hold the data. Thus, the malicious entity is able to write arbitrary data to kernel memory. Signed-off-by:
Ignat Korchagin <ignat.korchagin@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
-
Roman Pen authored
commit 346c09f8 upstream. The bug in a workqueue leads to a stalled IO request in MQ ctx->rq_list with the following backtrace: [ 601.347452] INFO: task kworker/u129:5:1636 blocked for more than 120 seconds. [ 601.347574] Tainted: G O 4.4.5-1-storage+ #6 [ 601.347651] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 601.348142] kworker/u129:5 D ffff880803077988 0 1636 2 0x00000000 [ 601.348519] Workqueue: ibnbd_server_fileio_wq ibnbd_dev_file_submit_io_worker [ibnbd_server] [ 601.348999] ffff880803077988 ffff88080466b900 ffff8808033f9c80 ffff880803078000 [ 601.349662] ffff880807c95000 7fffffffffffffff ffffffff815b0920 ffff880803077ad0 [ 601.350333] ffff8808030779a0 ffffffff815b01d5 0000000000000000 ffff880803077a38 [ 601.350965] Call Trace: [ 601.351203] [<ffffffff815b0920>] ? bit_wait+0x60/0x60 [ 601.351444] [<ffffffff815b01d5>] schedule+0x35/0x80 [ 601.351709] [<ffffffff815b2dd2>] schedule_timeout+0x192/0x230 [ 601.351958] [<ffffffff812d43f7>] ? blk_flush_plug_list+0xc7/0x220 [ 601.352208] [<ffffffff810bd737>] ? ktime_get+0x37/0xa0 [ 601.352446] [<ffffffff815b0920>] ? bit_wait+0x60/0x60 [ 601.352688] [<ffffffff815af784>] io_schedule_timeout+0xa4/0x110 [ 601.352951] [<ffffffff815b3a4e>] ? _raw_spin_unlock_irqrestore+0xe/0x10 [ 601.353196] [<ffffffff815b093b>] bit_wait_io+0x1b/0x70 [ 601.353440] [<ffffffff815b056d>] __wait_on_bit+0x5d/0x90 [ 601.353689] [<ffffffff81127bd0>] wait_on_page_bit+0xc0/0xd0 [ 601.353958] [<ffffffff81096db0>] ? autoremove_wake_function+0x40/0x40 [ 601.354200] [<ffffffff81127cc4>] __filemap_fdatawait_range+0xe4/0x140 [ 601.354441] [<ffffffff81127d34>] filemap_fdatawait_range+0x14/0x30 [ 601.354688] [<ffffffff81129a9f>] filemap_write_and_wait_range+0x3f/0x70 [ 601.354932] [<ffffffff811ced3b>] blkdev_fsync+0x1b/0x50 [ 601.355193] [<ffffffff811c82d9>] vfs_fsync_range+0x49/0xa0 [ 601.355432] [<ffffffff811cf45a>] blkdev_write_iter+0xca/0x100 [ 601.355679] [<ffffffff81197b1a>] __vfs_write+0xaa/0xe0 [ 601.355925] [<ffffffff81198379>] vfs_write+0xa9/0x1a0 [ 601.356164] [<ffffffff811c59d8>] kernel_write+0x38/0x50 The underlying device is a null_blk, with default parameters: queue_mode = MQ submit_queues = 1 Verification that nullb0 has something inflight: root@pserver8:~# cat /sys/block/nullb0/inflight 0 1 root@pserver8:~# find /sys/block/nullb0/mq/0/cpu* -name rq_list -print -exec cat {} \; ... /sys/block/nullb0/mq/0/cpu2/rq_list CTX pending: ffff8838038e2400 ... During debug it became clear that stalled request is always inserted in the rq_list from the following path: save_stack_trace_tsk + 34 blk_mq_insert_requests + 231 blk_mq_flush_plug_list + 281 blk_flush_plug_list + 199 wait_on_page_bit + 192 __filemap_fdatawait_range + 228 filemap_fdatawait_range + 20 filemap_write_and_wait_range + 63 blkdev_fsync + 27 vfs_fsync_range + 73 blkdev_write_iter + 202 __vfs_write + 170 vfs_write + 169 kernel_write + 56 So blk_flush_plug_list() was called with from_schedule == true. If from_schedule is true, that means that finally blk_mq_insert_requests() offloads execution of __blk_mq_run_hw_queue() and uses kblockd workqueue, i.e. it calls kblockd_schedule_delayed_work_on(). That means, that we race with another CPU, which is about to execute __blk_mq_run_hw_queue() work. Further debugging shows the following traces from different CPUs: CPU#0 CPU#1 ---------------------------------- ------------------------------- reqeust A inserted STORE hctx->ctx_map[0] bit marked kblockd_schedule...() returns 1 <schedule to kblockd workqueue> request B inserted STORE hctx->ctx_map[1] bit marked kblockd_schedule...() returns 0 *** WORK PENDING bit is cleared *** flush_busy_ctxs() is executed, but bit 1, set by CPU#1, is not observed As a result request B pended forever. This behaviour can be explained by speculative LOAD of hctx->ctx_map on CPU#0, which is reordered with clear of PENDING bit and executed _before_ actual STORE of bit 1 on CPU#1. The proper fix is an explicit full barrier <mfence>, which guarantees that clear of PENDING bit is to be executed before all possible speculative LOADS or STORES inside actual work function. Signed-off-by:
Roman Pen <roman.penyaev@profitbricks.com> Cc: Gioh Kim <gi-oh.kim@profitbricks.com> Cc: Michael Wang <yun.wang@profitbricks.com> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: linux-block@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Laszlo Ersek authored
commit 630ba0cc upstream. The variable_matches() function can currently read "var_name[len]", for example when: - var_name[0] == 'a', - len == 1 - match_name points to the NUL-terminated string "ab". This function is supposed to accept "var_name" inputs that are not NUL-terminated (hence the "len" parameter"). Document the function, and access "var_name[*match]" only if "*match" is smaller than "len". Reported-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Laszlo Ersek <lersek@redhat.com> Cc: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@coreos.com> Cc: Jason Andryuk <jandryuk@gmail.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Link: http://thread.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/86906Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
-
Sugar Zhang authored
commit 653aa464 upstream. this patch corrects the interface adc/dac control register definition according to datasheet. Signed-off-by:
Sugar Zhang <sugar.zhang@rock-chips.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Arnd Bergmann authored
commit ba4bc32e upstream. An older patch to convert the API in the s3c i2s driver ended up passing a const pointer into a function that takes a non-const pointer, so we now get a warning: sound/soc/samsung/s3c2412-i2s.c: In function 's3c2412_iis_dev_probe': sound/soc/samsung/s3c2412-i2s.c:172:9: error: passing argument 3 of 's3c_i2sv2_register_component' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers] However, the s3c_i2sv2_register_component() function again passes the pointer into another function taking a const, so we just need to change its prototype. Fixes: eca3b01d ("ASoC: switch over to use snd_soc_register_component() on s3c i2s") Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Tony Luck authored
commit c4fc1956 upstream. Both of these drivers can return NOTIFY_BAD, but this terminates processing other callbacks that were registered later on the chain. Since the driver did nothing to log the error it seems wrong to prevent other interested parties from seeing it. E.g. neither of them had even bothered to check the type of the error to see if it was a memory error before the return NOTIFY_BAD. Signed-off-by:
Tony Luck <tony.luck@intel.com> Acked-by:
Aristeu Rozanski <aris@redhat.com> Acked-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/72937355dd92318d2630979666063f8a2853495b.1461864507.git.tony.luck@intel.comSigned-off-by:
-
Javier Martinez Canillas authored
commit 10ff4c52 upstream. The exynos5 I2C controller driver always prepares and enables a clock before using it and then disables unprepares it when the clock is not used anymore. But this can cause a possible ABBA deadlock in some scenarios since a driver that uses regmap to access its I2C registers, will first grab the regmap lock and then the I2C xfer function will grab the prepare lock when preparing the I2C clock. But since the clock driver also uses regmap for I2C accesses, preparing a clock will first grab the prepare lock and then the regmap lock when using the regmap API. An example of this happens on the Exynos5422 Odroid XU4 board where a s2mps11 PMIC is used and both the s2mps11 regulators and clk drivers share the same I2C regmap. The possible deadlock is reported by the kernel lockdep: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(sec_core:428:(regmap)->lock); lock(prepare_lock); lock(sec_core:428:(regmap)->lock); lock(prepare_lock); *** DEADLOCK *** Fix it by leaving the code prepared on probe and use {en,dis}able in the I2C transfer function. This patch is similar to commit 34e81ad5 ("i2c: s3c2410: fix ABBA deadlock by keeping clock prepared") that fixes the same bug in other driver for an I2C controller found in Samsung SoCs. Reported-by:
Anand Moon <linux.amoon@gmail.com> Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Michael Ellerman authored
commit 609d5a1b upstream. Since commit ea8daa7b ("kbuild: Add option to turn incompatible pointer check into error"), assignments from an incompatible pointer types have become a hard error, eg: drivers/i2c/busses/i2c-cpm.c:545:91: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type Fix the build break by converting txdma & rxdma to dma_addr_t. Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Keerthy authored
commit 56b367c0 upstream. pcs_parse_bits_in_pinctrl_entry uses ffs which gives bit indices ranging from 1 to MAX. This leads to a corner case where we try to request the pin number = MAX and fails. bit_pos value is being calculted using ffs. pin_num_from_lsb uses bit_pos value. pins array is populated with: pin + pin_num_from_lsb. The above is 1 more than usual bit indices as bit_pos uses ffs to compute first set bit. Hence the last of the pins array is populated with the MAX value and not MAX - 1 which causes error when we call pin_request. mask_pos is rightly calculated as ((pcs->fmask) << (bit_pos - 1)) Consequently val_pos and submask are correct. Hence use __ffs which gives (ffs(x) - 1) as the first bit set. fixes: 4e7e8017 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules") Signed-off-by:
Keerthy <j-keerthy@ti.com> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Vladis Dronov authored
commit 162f98de upstream. The gtco driver expects at least one valid endpoint. If given malicious descriptors that specify 0 for the number of endpoints, it will crash in the probe function. Ensure there is at least one endpoint on the interface before using it. Also let's fix a minor coding style issue. The full correct report of this issue can be found in the public Red Hat Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1283385Reported-by:
Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Dmitry Ivanov authored
commit 8f815cdd upstream. A non-privileged user can create a netlink socket with the same port_id as used by an existing open nl80211 netlink socket (e.g. as used by a hostapd process) with a different protocol number. Closing this socket will then lead to the notification going to nl80211's socket release notification handler, and possibly cause an action such as removing a virtual interface. Fix this issue by checking that the netlink protocol is NETLINK_GENERIC. Since generic netlink has no notifier chain of its own, we can't fix the problem more generically. Fixes: 026331c4 ("cfg80211/mac80211: allow registering for and sending action frames") Signed-off-by:
Dmitry Ivanov <dima@ubnt.com> [rewrite commit message] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Herbert Xu authored
This bug has already bee fixed upstream since 4.2. However, it was fixed during the AEAD conversion so no fix was backported to the older kernels. When we do an RFC 4543 decryption, we will end up writing the ICV beyond the end of the dst buffer. This should lead to a crash but for some reason it was never noticed. This patch fixes it by only writing back the ICV for encryption. Fixes: d733ac90 ("crypto: gcm - fix rfc4543 to handle async...") Reported-by:
Patrick Meyer <patrick.meyer@vasgard.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Tom Lendacky authored
commit f709b45e upstream. Prevent information from leaking to userspace by doing a memset to 0 of the export state structure before setting the structure values and copying it. This prevents un-initialized padding areas from being copied into the export area. Reported-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
John Keeping authored
commit d59a1f71 upstream. The SPICE protocol considers the position of a cursor to be the location of its active pixel on the display, so the cursor is drawn with its top-left corner at "(x - hot_spot_x, y - hot_spot_y)" but the DRM cursor position gives the location where the top-left corner should be drawn, with the hotspot being a hint for drivers that need it. This fixes the location of the window resize cursors when using Fluxbox with the QXL DRM driver and both the QXL and modesetting X drivers. Signed-off-by:
John Keeping <john@metanate.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1447845445-2116-1-git-send-email-john@metanate.comSigned-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Davidlohr Bueso authored
commit fe1bce9e upstream. Otherwise an incoming waker on the dest hash bucket can miss the waiter adding itself to the plist during the lockless check optimization (small window but still the correct way of doing this); similarly to the decrement counterpart. Suggested-by:
Peter Zijlstra <peterz@infradead.org> Signed-off-by:
Davidlohr Bueso <dbueso@suse.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: bigeasy@linutronix.de Cc: dvhart@infradead.org Link: http://lkml.kernel.org/r/1461208164-29150-1-git-send-email-dave@stgolabs.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Andy Lutomirski authored
commit b7a58459 upstream. On Xen PV, regs->flags doesn't reliably reflect IOPL and the exit-to-userspace code doesn't change IOPL. We need to context switch it manually. I'm doing this without going through paravirt because this is specific to Xen PV. After the dust settles, we can merge this with the 32-bit code, tidy up the iopl syscall implementation, and remove the set_iopl pvop entirely. Fixes XSA-171. Reviewewd-by:
Jan Beulich <JBeulich@suse.com> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <JBeulich@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/693c3bd7aeb4d3c27c92c622b7d0f554a458173c.1458162709.git.luto@kernel.orgSigned-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
Rui Salvaterra authored
commit 3e26a691 upstream. Based on Sergey's test patch [1], this fixes zram with lz4 compression on big endian cpus. Note that the 64-bit preprocessor test is not a cleanup, it's part of the fix, since those identifiers are bogus (for example, __ppc64__ isn't defined anywhere else in the kernel, which means we'd fall into the 32-bit definitions on ppc64). Tested on ppc64 with no regression on x86_64. [1] http://marc.info/?l=linux-kernel&m=145994470805853&w=4Suggested-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by:
Rui Salvaterra <rsalvaterra@gmail.com> Reviewed-by:
-
Robert Dobrowolski authored
commit e86103a7 upstream. On BXT platform Host Controller and Device Controller figure as same PCI device but with different device function. HCD should not pass data to Device Controller but only to Host Controllers. Checking if companion device is Host Controller, otherwise skip. Signed-off-by:
Robert Dobrowolski <robert.dobrowolski@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Lu Baolu authored
commit 71504062 upstream. This patch fixes some wild pointers produced by xhci_mem_cleanup. These wild pointers will cause system crash if xhci_mem_cleanup() is called twice. Reported-and-tested-by:
Pengcheng Li <lpc.li@hisilicon.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Jerome Marchand authored
commit 8d4a2ec1 upstream. Changes since V1: fixed the description and added KASan warning. In assoc_array_insert_into_terminal_node(), we call the compare_object() method on all non-empty slots, even when they're not leaves, passing a pointer to an unexpected structure to compare_object(). Currently it causes an out-of-bound read access in keyring_compare_object detected by KASan (see below). The issue is easily reproduced with keyutils testsuite. Only call compare_object() when the slot is a leave. KASan warning: ================================================================== BUG: KASAN: slab-out-of-bounds in keyring_compare_object+0x213/0x240 at addr ffff880060a6f838 Read of size 8 by task keyctl/1655 ============================================================================= BUG kmalloc-192 (Not tainted): kasan: bad access detected ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in assoc_array_insert+0xfd0/0x3a60 age=69 cpu=1 pid=1647 ___slab_alloc+0x563/0x5c0 __slab_alloc+0x51/0x90 kmem_cache_alloc_trace+0x263/0x300 assoc_array_insert+0xfd0/0x3a60 __key_link_begin+0xfc/0x270 key_create_or_update+0x459/0xaf0 SyS_add_key+0x1ba/0x350 entry_SYSCALL_64_fastpath+0x12/0x76 INFO: Slab 0xffffea0001829b80 objects=16 used=8 fp=0xffff880060a6f550 flags=0x3fff8000004080 INFO: Object 0xffff880060a6f740 @offset=5952 fp=0xffff880060a6e5d1 Bytes b4 ffff880060a6f730: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f740: d1 e5 a6 60 00 88 ff ff 0e 00 00 00 00 00 00 00 ...`............ Object ffff880060a6f750: 02 cf 8e 60 00 88 ff ff 02 c0 8e 60 00 88 ff ff ...`.......`.... Object ffff880060a6f760: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f770: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f780: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f790: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7d0: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ CPU: 0 PID: 1655 Comm: keyctl Tainted: G B 4.5.0-rc4-kasan+ #291 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 0000000000000000 000000001b2800b4 ffff880060a179e0 ffffffff81b60491 ffff88006c802900 ffff880060a6f740 ffff880060a17a10 ffffffff815e2969 ffff88006c802900 ffffea0001829b80 ffff880060a6f740 ffff880060a6e650 Call Trace: [<ffffffff81b60491>] dump_stack+0x85/0xc4 [<ffffffff815e2969>] print_trailer+0xf9/0x150 [<ffffffff815e9454>] object_err+0x34/0x40 [<ffffffff815ebe50>] kasan_report_error+0x230/0x550 [<ffffffff819949be>] ? keyring_get_key_chunk+0x13e/0x210 [<ffffffff815ec62d>] __asan_report_load_n_noabort+0x5d/0x70 [<ffffffff81994cc3>] ? keyring_compare_object+0x213/0x240 [<ffffffff81994cc3>] keyring_compare_object+0x213/0x240 [<ffffffff81bc238c>] assoc_array_insert+0x86c/0x3a60 [<ffffffff81bc1b20>] ? assoc_array_cancel_edit+0x70/0x70 [<ffffffff8199797d>] ? __key_link_begin+0x20d/0x270 [<ffffffff8199786c>] __key_link_begin+0xfc/0x270 [<ffffffff81993389>] key_create_or_update+0x459/0xaf0 [<ffffffff8128ce0d>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff81992f30>] ? key_type_lookup+0xc0/0xc0 [<ffffffff8199e19d>] ? lookup_user_key+0x13d/0xcd0 [<ffffffff81534763>] ? memdup_user+0x53/0x80 [<ffffffff819983ea>] SyS_add_key+0x1ba/0x350 [<ffffffff81998230>] ? key_get_type_from_user.constprop.6+0xa0/0xa0 [<ffffffff828bcf4e>] ? retint_user+0x18/0x23 [<ffffffff8128cc7e>] ? trace_hardirqs_on_caller+0x3fe/0x580 [<ffffffff81004017>] ? trace_hardirqs_on_thunk+0x17/0x19 [<ffffffff828bc432>] entry_SYSCALL_64_fastpath+0x12/0x76 Memory state around the buggy address: ffff880060a6f700: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00 ffff880060a6f780: 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc >ffff880060a6f800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff880060a6f880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff880060a6f900: fc fc fc fc fc fc 00 00 00 00 00 00 00 00 00 00 ================================================================== Signed-off-by:
Jerome Marchand <jmarchan@redhat.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Lokesh Vutla authored
commit 3ca4a238 upstream. Commit 127500cc ("ARM: OMAP2+: Only write the sysconfig on idle when necessary") talks about verification of sysconfig cache value before updating it, only during idle path. But the patch is adding the verification in the enable path. So, adding the check in a proper place as per the commit description. Not keeping this check during enable path as there is a chance of losing context and it is safe to do on idle as the context of the register will never be lost while the device is active. Signed-off-by:
Lokesh Vutla <lokeshvutla@ti.com> Acked-by:
Tero Kristo <t-kristo@ti.com> Cc: Jon Hunter <jonathanh@nvidia.com> Fixes: commit 127500cc "ARM: OMAP2+: Only write the sysconfig on idle when necessary" [paul@pwsan.com: appears to have been caused by my own mismerge of the originally posted patch] Signed-off-by:
Paul Walmsley <paul@pwsan.com> Signed-off-by:
-
- 20 Apr, 2016 6 commits
-
-
Greg Kroah-Hartman authored
-
Greg Kroah-Hartman authored
commit e5bdfd50 upstream. This reverts commit d8f00cd6. Tony writes: This upstream commit is causing an oops: d8f00cd6 ("usb: hub: do not clear BOS field during reset device") This patch has already been included in several -stable kernels. Here are the affected kernels: 4.5.0-rc4 (current git) 4.4.2 4.3.6 (currently in review) 4.1.18 3.18.27 3.14.61 How to reproduce the problem: Boot kernel with slub debugging enabled (otherwise memory corruption will cause random oopses later instead of immediately) Plug in USB 3.0 disk to xhci USB 3.0 port dd if=/dev/sdc of=/dev/null bs=65536 (where /dev/sdc is the USB 3.0 disk) Unplug USB cable while dd is still going Oops is immediate: Reported-by:
Tony Battersby <tonyb@cybernetics.com> Cc: Du, Changbin <changbin.du@intel.com> Cc: Roger Quadros <rogerq@ti.com> Signed-off-by:
-
Vladis Dronov authored
commit fa52bd50 upstream. The usbvision driver crashes when a specially crafted usb device with invalid number of interfaces or endpoints is detected. This fix adds checks that the device has proper configuration expected by the driver. Reported-by:
-
Alexey Khoroshilov authored
commit afd270d1 upstream. There is no usb_put_dev() on failure paths in usbvision_probe(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Nicolai Hähnle authored
[Backport of upstream commit f6ff4f67, with an additional NULL pointer guard that is required for kernels 3.17 and older. To be precise, any kernel that does *not* have commit 954605ca "drm/radeon: use common fence implementation for fences, v4" requires this additional NULL pointer guard.] An arbitrary amount of time can pass between spin_unlock and radeon_fence_wait_any, so we need to ensure that nobody frees the fences from under us. Based on the analogous fix for amdgpu. Signed-off-by:
Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> (v1 + fix) Tested-by:
Lutz Euler <lutz.euler@freenet.de> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit 50353e6f, which is commit f6ff4f67 upstream, as it was backported to the 3.14-stable tree incorrectly. A correct fix will happen next. Reported-by:
-
