IMX93 do not contain a GPR to config the stop mode, it will set
the flexcan into stop mode automatically once the ARM core go
into low power mode (WFI instruct) and gate off the flexcan
related clock automatically. But to let these logic work as
expect, before ARM core go into low power mode, need to make
sure the flexcan related clock keep on.

To support stop mode and wakeup feature on imx93, this patch
add a new fsl_imx93_devtype_data to separate from imx8mp.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/1669116752-4260-1-git-send-email-haibo.chen@nxp.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Follow the best practices, reorder the includes.

While doing so, bump up copyright year of each modified files.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221126160525.87036-1-mailhol.vincent@wanadoo.frSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit 0166dc11 ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.

It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: Ondrej Ille <ondrej.ille@gmail.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Link: https://lore.kernel.org/all/20221124141604.4265225f@endymion.delvareSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Biju Das <biju.das.jz@bp.renesas.com> says:

The CAN FD IP found on RZ/G2L SoC has some HW features different to
that of R-Car. For example, it has multiple resets, dedicated channel
tx and error interrupts, separate global rx and error interrupts
compared to shared irq for R-Car. it does not s ECC error flag
registers and clk post divider present on R-Car.

Similarly, R-Car V3U has 8 channels whereas other SoCs has only 2
channels. Currently all the HW differences are handled by comparing
with chip_id enum.

This patch series aims to replace chip_id with struct
rcar_canfd_hw_info to handle the HW feature differences and driver
data present on both IPs.

The changes are trivial and tested on RZ/G2L SMARC EVK.

This patch series depend upon [1].

[1] https://lore.kernel.org/all/20221025155657.1426948-1-biju.das.jz@bp.renesas.com

changes since v2: https://lore.kernel.org/all/20221026131732.1843105-1-biju.das.jz@bp.renesas.com
 * Replaced data type of max_channels from unsigned int->u8 to save memory.
 * Replaced data type of postdiv from unsigned int->u8 to save memory.

changes since v1: https://lore.kernel.org/all/20221022104357.1276740-1-biju.das.jz@bp.renesas.com
 * Updated commit description for R-Car V3U SoC detection using
   driver data.
 * Replaced data type of max_channels from u32->unsigned int.
 * Replaced multi_global_irqs->shared_global_irqs to make it
   positive checks.
 * Replaced clk_postdiv->postdiv driver data variable.
 * Simplified the calcualtion for fcan_freq.
 * Replaced info->has_gerfl to gpriv->info->has_gerfl and wrapped
   the ECC error flag checks inside a single if statement.
 * Added Rb tag from Geert patch#1,#2,#3 and #5

Link: https://lore.kernel.org/all/20221027082158.95895-1-biju.das.jz@bp.renesas.com
[mkl: only take patches 1...5 to avoid merge conflict]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

RZ/G2L has separate IRQ lines for tx and error interrupt for each
channel whereas R-Car has a combined IRQ line for all the channel
specific tx and error interrupts.

Add multi_channel_irqs to struct rcar_canfd_hw_info to select the
driver to choose between combined and separate irq registration for
channel interrupts. This patch also removes enum rcanfd_chip_id and
chip_id from both struct rcar_canfd_hw_info, as it is unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221027082158.95895-6-biju.das.jz@bp.renesas.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

R-Car has a clock divider for CAN FD clock within the IP, whereas
it is not available on RZ/G2L.

Add postdiv variable to struct rcar_canfd_hw_info to take care of this
difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221027082158.95895-5-biju.das.jz@bp.renesas.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

RZ/G2L has separate IRQ lines for receive FIFO and global error interrupt
whereas R-Car has shared IRQ line.

Add shared_global_irqs to struct rcar_canfd_hw_info to select the driver to
choose between shared and separate irq registration for global
interrupts.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221027082158.95895-4-biju.das.jz@bp.renesas.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

R-Car V3U supports a maximum of 8 channels whereas rest of the SoCs
support 2 channels.

Add max_channels variable to struct rcar_canfd_hw_info to handle this
difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221027082158.95895-3-biju.das.jz@bp.renesas.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Sort header inclusion alphabetically.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Vivek Yadav <vivek.2311@samsung.com>
Link: https://lore.kernel.org/all/20221104051617.21173-1-vivek.2311@samsung.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The CAN FD IP found on RZ/G2L SoC has some HW features different to that
of R-Car. For example, it has multiple resets and multiple IRQs for global
and channel interrupts. Also, it does not have ECC error flag registers
and clk post divider present on R-Car. Similarly, R-Car V3U has 8 channels
whereas other SoCs has only 2 channels.

This patch adds the struct rcar_canfd_hw_info to take care of the
HW feature differences and driver data present on both IPs. It also
replaces the driver data chip type with struct rcar_canfd_hw_info by
moving chip type to it.

Whilst started using driver data instead of chip_id for detecting
R-Car V3U SoCs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221027082158.95895-2-biju.das.jz@bp.renesas.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Fix coding style by removing empty lines in variable declaration.

Fixes: 39d3df6b ("can: kvaser_usb: Compare requested bittiming parameters with actual parameters in do_set_{,data}_bittiming")
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/all/20221031114513.81214-2-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The variable err is initialized, but the initialized value is
Overwritten before it is read. Fix the warning by not initializing the
variable err at all.

Fixes: 39d3df6b ("can: kvaser_usb: Compare requested bittiming parameters with actual parameters in do_set_{,data}_bittiming")
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/all/20221031114513.81214-1-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Merge tag 'ipsec-next-2022-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next

Steffen Klassert says:

====================
ipsec-next 2022-12-09

1) Add xfrm packet offload core API.
   From Leon Romanovsky.

2) Add xfrm packet offload support for mlx5.
   From Leon Romanovsky and Raed Salem.

3) Fix a typto in a error message.
   From Colin Ian King.

* tag 'ipsec-next-2022-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next: (38 commits)
  xfrm: Fix spelling mistake "oflload" -> "offload"
  net/mlx5e: Open mlx5 driver to accept IPsec packet offload
  net/mlx5e: Handle ESN update events
  net/mlx5e: Handle hardware IPsec limits events
  net/mlx5e: Update IPsec soft and hard limits
  net/mlx5e: Store all XFRM SAs in Xarray
  net/mlx5e: Provide intermediate pointer to access IPsec struct
  net/mlx5e: Skip IPsec encryption for TX path without matching policy
  net/mlx5e: Add statistics for Rx/Tx IPsec offloaded flows
  net/mlx5e: Improve IPsec flow steering autogroup
  net/mlx5e: Configure IPsec packet offload flow steering
  net/mlx5e: Use same coding pattern for Rx and Tx flows
  net/mlx5e: Add XFRM policy offload logic
  net/mlx5e: Create IPsec policy offload tables
  net/mlx5e: Generalize creation of default IPsec miss group and rule
  net/mlx5e: Group IPsec miss handles into separate struct
  net/mlx5e: Make clear what IPsec rx_err does
  net/mlx5e: Flatten the IPsec RX add rule path
  net/mlx5e: Refactor FTE setup code to be more clear
  net/mlx5e: Move IPsec flow table creation to separate function
  ...
====================

Link: https://lore.kernel.org/r/20221209093310.4018731-1-steffen.klassert@secunet.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When the resource size changes, the return value of the
'nla_put_u64_64bit' function is not checked. That has been fixed to avoid
rechecking at the next step.

Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.

Note that this is harmless, we'd error out at the next put().
Signed-off-by: Ilia.Gavrilov <Ilia.Gavrilov@infotecs.ru>
Link: https://lore.kernel.org/r/20221208082821.3927937-1-Ilia.Gavrilov@infotecs.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzkaller reported:

  BUG: KASAN: slab-out-of-bounds in __build_skb_around+0x235/0x340 net/core/skbuff.c:294
  Write of size 32 at addr ffff88802aa172c0 by task syz-executor413/5295

For bpf_prog_test_run_skb(), which uses a kmalloc()ed buffer passed to
build_skb().

When build_skb() is passed a frag_size of 0, it means the buffer came
from kmalloc. In these cases, ksize() is used to find its actual size,
but since the allocation may not have been made to that size, actually
perform the krealloc() call so that all the associated buffer size
checking will be correctly notified (and use the "new" pointer so that
compiler hinting works correctly). Split this logic out into a new
interface, slab_build_skb(), but leave the original 0 checking for now
to catch any stragglers.

Reported-by: syzbot+fda18eaa8c12534ccb3b@syzkaller.appspotmail.com
Link: https://groups.google.com/g/syzkaller-bugs/c/UnIKxTtU5-0/m/-wbXinkgAQAJ
Fixes: 38931d89 ("mm: Make ksize() a reporting-only function")
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: pepsipu <soopthegoop@gmail.com>
Cc: syzbot+fda18eaa8c12534ccb3b@syzkaller.appspotmail.com
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: kasan-dev <kasan-dev@googlegroups.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: ast@kernel.org
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Hao Luo <haoluo@google.com>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: jolsa@kernel.org
Cc: KP Singh <kpsingh@kernel.org>
Cc: martin.lau@linux.dev
Cc: Stanislav Fomichev <sdf@google.com>
Cc: song@kernel.org
Cc: Yonghong Song <yhs@fb.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221208060256.give.994-kees@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The function dmadesc_get_addr() is defined in the bcmgenet.c file, but
not called elsewhere, so remove this unused function.

drivers/net/ethernet/broadcom/genet/bcmgenet.c:120:26: warning: unused function 'dmadesc_get_addr'.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3401Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221209033723.32452-1-jiapeng.chong@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Mat Martineau says:

====================
mptcp: Miscellaneous cleanup

Two code cleanup patches for the 6.2 merge window that don't change
behavior:

Patch 1 makes proper use of nlmsg_free(), as suggested by Jakub while
reviewing f8c9dfbd ("mptcp: add pm listener events").

Patch 2 clarifies success status in a few mptcp functions, which
prevents some smatch false positives.
====================

Link: https://lore.kernel.org/r/20221209004431.143701-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When 'err' is 0, it looks clearer to return '0' instead of the variable
called 'err'.

The behaviour is then not modified, just a clearer code.

By doing this, we can also avoid false positive smatch warnings like
this one:

  net/mptcp/pm_netlink.c:1169 mptcp_pm_parse_pm_addr_attr() warn: missing error code? 'err'
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use nlmsg_free() instead of kfree_skb() in pm_netlink.c.

The SKB's have been created by nlmsg_new(). The proper cleaning way
should then be done with nlmsg_free().

For the moment, nlmsg_free() is simply calling kfree_skb() so we don't
change the behaviour here.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5-updates-2022-12-08

1) Support range match action in SW steering

Yevgeny Kliteynik says:
=======================

The following patch series adds support for a range match action in
SW Steering.

SW steering is able to match only on the exact values of the packet fields,
as requested by the user: the user provides mask for the fields that are of
interest, and the exact values to be matched on when the traffic is handled.

The following patch series add new type of action - Range Match, where the
user provides a field to be matched on and a range of values (min to max)
that will be considered as hit.

There are several new notions that were implemented in order to support
Range Match:
 - MATCH_RANGES Steering Table Entry (STE): the new STE type that allows
   matching the packets' fields on the range of values instead of a specific
   value.
 - Match Definer: this is a general FW object that defines which fields
   in the packet will be referenced by the mask and tag of each STE.
   Match definer ID is part of STE fields, and it defines how the HW needs
   to interpret the STE's mask/tag values.
   Till now SW steering used the definers that were managed by FW and
   implemented the STE layout as described by the HW spec.
   Now that we're adding a new type of STE, SW steering needs to also be
   able to define this new STE's layout, and this is do

=======================

2) From OZ add support for meter mtu offload
   2.1: Refactor the code to allow both metering and range post actions as a
        pre-step for adding police mtu offload support.
   2.2: Instantiate mtu green/red flow tables with a single match-all rule.
        Add the green/red actions to the hit/miss table accordingly
   2.3: Initialize the meter object with the TC police mtu parameter.
        Use the hardware range match action feature.

3) From MaorD, support routes with more than 2 nexthops in multipath

4) Michael and Or, improve and extend vport representor counters.

* tag 'mlx5-updates-2022-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5: Expose steering dropped packets counter
  net/mlx5: Refactor and expand rep vport stat group
  net/mlx5e: multipath, support routes with more than 2 nexthops
  net/mlx5e: TC, add support for meter mtu offload
  net/mlx5e: meter, add mtu post meter tables
  net/mlx5e: meter, refactor to allow multiple post meter tables
  net/mlx5: DR, Add support for range match action
  net/mlx5: DR, Add function that tells if STE miss addr has been initialized
  net/mlx5: DR, Some refactoring of miss address handling
  net/mlx5: DR, Manage definers with refcounts
  net/mlx5: DR, Handle FT action in a separate function
  net/mlx5: DR, Rework is_fw_table function
  net/mlx5: DR, Add functions to create/destroy MATCH_DEFINER general object
  net/mlx5: fs, add match on ranges API
  net/mlx5: mlx5_ifc updates for MATCH_DEFINER general object
====================

Link: https://lore.kernel.org/r/20221209001420.142794-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-12-08 (ice)

Jacob Keller says:

This series of patches primarily consists of changes to fix some corner
cases that can cause Tx timestamp failures. The issues were discovered and
reported by Siddaraju DH and primarily affect E822 hardware, though this
series also includes some improvements that affect E810 hardware as well.

The primary issue is regarding the way that E822 determines when to generate
timestamp interrupts. If the driver reads timestamp indexes which do not
have a valid timestamp, the E822 interrupt tracking logic can get stuck.
This is due to the way that E822 hardware tracks timestamp index reads
internally. I was previously unaware of this behavior as it is significantly
different in E810 hardware.

Most of the fixes target refactors to ensure that the ice driver does not
read timestamp indexes which are not valid on E822 hardware. This is done by
using the Tx timestamp ready bitmap register from the PHY. This register
indicates what timestamp indexes have outstanding timestamps waiting to be
captured.

Care must be taken in all cases where we read the timestamp registers, and
thus all flows which might have read these registers are refactored. The
ice_ptp_tx_tstamp function is modified to consolidate as much of the logic
relating to these registers as possible. It now handles discarding stale
timestamps which are old or which occurred after a PHC time update. This
replaces previously standalone thread functions like the periodic work
function and the ice_ptp_flush_tx_tracker function.

In addition, some minor cleanups noticed while writing these refactors are
included.

The remaining patches refactor the E822 implementation to remove the
"bypass" mode for timestamps. The E822 hardware has the ability to provide a
more precise timestamp by making use of measurements of the precise way that
packets flow through the hardware pipeline. These measurements are known as
"Vernier" calibration. The "bypass" mode disables many of these measurements
in favor of a faster start up time for Tx and Rx timestamping. Instead, once
these measurements were captured, the driver tries to reconfigure the PHY to
enable the vernier calibrations.

Unfortunately this recalibration does not work. Testing indicates that the
PHY simply remains in bypass mode without the increased timestamp precision.
Remove the attempt at recalibration and always use vernier mode. This has
one disadvantage that Tx and Rx timestamps cannot begin until after at least
one packet of that type goes through the hardware pipeline. Because of this,
further refactor the driver to separate Tx and Rx vernier calibration.
Complete the Tx and Rx independently, enabling the appropriate type of
timestamp as soon as the relevant packet has traversed the hardware
pipeline. This was reported by Milena Olech.

Note that although these might be considered "bug fixes", the required
changes in order to appropriately resolve these issues is large. Thus it
does not feel suitable to send this series to net.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ice: reschedule ice_ptp_wait_for_offset_valid during reset
  ice: make Tx and Rx vernier offset calibration independent
  ice: only check set bits in ice_ptp_flush_tx_tracker
  ice: handle flushing stale Tx timestamps in ice_ptp_tx_tstamp
  ice: cleanup allocations in ice_ptp_alloc_tx_tracker
  ice: protect init and calibrating check in ice_ptp_request_ts
  ice: synchronize the misc IRQ when tearing down Tx tracker
  ice: check Tx timestamp memory register for ready timestamps
  ice: handle discarding old Tx requests in ice_ptp_tx_tstamp
  ice: always call ice_ptp_link_change and make it void
  ice: fix misuse of "link err" with "link status"
  ice: Reset TS memory for all quads
  ice: Remove the E822 vernier "bypass" logic
  ice: Use more generic names for ice_ptp_tx fields
====================

Link: https://lore.kernel.org/r/20221208213932.1274143-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add support to count upall packets, when kmod of openvswitch
upcall to count the number of packets for upcall succeed and
failed, which is a better way to see how many packets upcalled
on every interfaces.
Signed-off-by: wangchuanlei <wangchuanlei@inspur.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rhashtable currently only does bh-safe synchronization making it impossible
to use from irq-safe contexts. Switch it to use irq-safe synchronization to
remove the restriction.

v2: Update the lock functions to return the ulong flags value and unlock
    functions to take the value directly instead of passing around the
    pointer. Suggested by Linus.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Vernet <dvernet@meta.com>
Acked-by: Josh Don <joshdon@google.com>
Acked-by: Hao Luo <haoluo@google.com>
Acked-by: Barret Rhoden <brho@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pedro Tammela says:

====================
net/sched: retpoline wrappers for tc

In tc all qdics, classifiers and actions can be compiled as modules.
This results today in indirect calls in all transitions in the tc hierarchy.
Due to CONFIG_RETPOLINE, CPUs with mitigations=on might pay an extra cost on
indirect calls. For newer Intel cpus with IBRS the extra cost is
nonexistent, but AMD Zen cpus and older x86 cpus still go through the
retpoline thunk.

Known built-in symbols can be optimized into direct calls, thus
avoiding the retpoline thunk. So far, tc has not been leveraging this
build information and leaving out a performance optimization for some
CPUs. In this series we wire up 'tcf_classify()' and 'tcf_action_exec()'
with direct calls when known modules are compiled as built-in as an
opt-in optimization.

We measured these changes in one AMD Zen 4 cpu (Retpoline), one AMD Zen 3 cpu (Retpoline),
one Intel 10th Gen CPU (IBRS), one Intel 3rd Gen cpu (Retpoline) and one
Intel Xeon CPU (IBRS) using pktgen with 64b udp packets. Our test setup is a
dummy device with clsact and matchall in a kernel compiled with every
tc module as built-in.  We observed a 3-8% speed up on the retpoline CPUs,
when going through 1 tc filter, and a 60-100% speed up when going through 100 filters.
For the IBRS cpus we observed a 1-2% degradation in both scenarios, we believe
the extra branches check introduced a small overhead therefore we added
a static key that bypasses the wrapper on kernels not using the retpoline mitigation,
but compiled with CONFIG_RETPOLINE.

1 filter:
CPU        | before (pps) | after (pps) | diff
R9 7950X   | 5914980      | 6380227     | +7.8%
R9 5950X   | 4237838      | 4412241     | +4.1%
R9 5950X   | 4265287      | 4413757     | +3.4%   [*]
i5-3337U   | 1580565      | 1682406     | +6.4%
i5-10210U  | 3006074      | 3006857     | +0.0%
i5-10210U  | 3160245      | 3179945     | +0.6%   [*]
Xeon 6230R | 3196906      | 3197059a     | +0.0%
Xeon 6230R | 3190392      | 3196153     | +0.01%  [*]

100 filters:
CPU        | before (pps) | after (pps) | diff
R9 7950X   | 373598       | 820396      | +119.59%
R9 5950X   | 313469       | 633303      | +102.03%
R9 5950X   | 313797       | 633150      | +101.77% [*]
i5-3337U   | 127454       | 211210      | +65.71%
i5-10210U  | 389259       | 381765      | -1.9%
i5-10210U  | 408812       | 412730      | +0.9%    [*]
Xeon 6230R | 415420       | 406612      | -2.1%
Xeon 6230R | 416705       | 405869      | -2.6%    [*]

[*] In these tests we ran pktgen with clone set to 1000.

On the 7950x system we also tested the impact of filters if iteration order
placement varied, first by compiling a kernel with the filter under test being
the first one in the static iteration and then repeating it with being last (of 15 classifiers existing today).
We saw a difference of +0.5-1% in pps between being the first in the iteration vs being the last.
Therefore we order the classifiers and actions according to relevance per our current thinking.

v5->v6:
- Address Eric Dumazet suggestions

v4->v5:
- Rebase

v3->v4:
- Address Eric Dumazet suggestions

v2->v3:
- Address suggestions by Jakub, Paolo and Eric
- Dropped RFC tag (I forgot to add it on v2)

v1->v2:
- Fix build errors found by the bots
- Address Kuniyuki Iwashima suggestions

====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose the necessary tc classifier functions and wire up cls_api to use
direct calls in retpoline kernels.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose the necessary tc act functions and wire up act_api to use
direct calls in retpoline kernels.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On kernels using retpoline as a spectrev2 mitigation,
optimize actions and filters that are compiled as built-ins into a direct call.

On subsequent patches we expose the classifiers and actions functions
and wire up the wrapper into tc.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The type definition should be visible even in configurations not using
CONFIG_NET_CLS_ACT.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a NL_SET_ERR_MSG message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

Leon Romanovsky says:

============
This is second part with implementation of packet offload.
============
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

Delete a few lines of "depends on PHYLIB" since they are inside
an "if PHYLIB / endif # PHYLIB" block, i.e., they are redundant
and the other 50+ drivers there don't use "depends on PHYLIB"
since it is not needed.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221207044257.30036-1-rdunlap@infradead.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add an option to initialize SOF_TIMESTAMPING_OPT_ID for TCP from
write_seq sockets instead of snd_una.

This should have been the behavior from the start. Because processes
may now exist that rely on the established behavior, do not change
behavior of the existing option, but add the right behavior with a new
flag. It is encouraged to always set SOF_TIMESTAMPING_OPT_ID_TCP on
stream sockets along with the existing SOF_TIMESTAMPING_OPT_ID.

Intuitively the contract is that the counter is zero after the
setsockopt, so that the next write N results in a notification for
the last byte N - 1.

On idle sockets snd_una == write_seq and this holds for both. But on
sockets with data in transmission, snd_una records the unacked offset
in the stream. This depends on the ACK response from the peer. A
process cannot learn this in a race free manner (ioctl SIOCOUTQ is one
racy approach).

write_seq records the offset at the last byte written by the process.
This is a better starting point. It matches the intuitive contract in
all circumstances, unaffected by external behavior.

The new timestamp flag necessitates increasing sk_tsflags to 32 bits.
Move the field in struct sock to avoid growing the socket (for some
common CONFIG variants). The UAPI interface so_timestamping.flags is
already int, so 32 bits wide.
Reported-by: Sotirios Delimanolis <sotodel@meta.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20221207143701.29861-1-willemdebruijn.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Lorenzo Bianconi says:

====================
fix possible deadlock during WED attach

Fix a possible deadlock in mtk_wed_attach if mtk_wed_wo_init routine fails.
Check wo pointer is properly allocated before running mtk_wed_wo_reset() and
mtk_wed_wo_deinit().
====================

Link: https://lore.kernel.org/r/cover.1670421354.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce __mtk_wed_detach() in order to avoid a deadlock in
mtk_wed_attach routine if mtk_wed_wo_init fails since both
mtk_wed_attach and mtk_wed_detach run holding hw_lock mutex.

Fixes: 4c5de09e ("net: ethernet: mtk_wed: add configure wed wo support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix possible NULL pointer dereference in mtk_wed_detach routine checking
wo pointer is properly allocated before running mtk_wed_wo_reset() and
mtk_wed_wo_deinit().
Even if it is just a theoretical issue at the moment check wo pointer is
not NULL in mtk_wed_mcu_msg_update.
Moreover, honor mtk_wed_mcu_send_msg return value in mtk_wed_wo_reset()

Fixes: 79968444 ("net: ethernet: mtk_wed: introduce wed wo support")
Fixes: 4c5de09e ("net: ethernet: mtk_wed: add configure wed wo support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There is a spelling mistake in a nn_dp_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20221207094312.2281493-1-colin.i.king@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The BPF Makefile in net/bpf did incorrect path substitution for O=dir
builds, e.g.

  make O=/tmp/kselftest headers
  make O=/tmp/kselftest -C tools/testing/selftests

would fail in selftest builds [1] net/ with

  clang-16: error: no such file or directory: 'kselftest/net/bpf/nat6to4.c'
  clang-16: error: no input files

Add a pattern prerequisite and an order-only-prerequisite (for
creating the directory), to resolve the issue.

[1] https://lore.kernel.org/all/202212060009.34CkQmCN-lkp@intel.com/Reported-by: kernel test robot <lkp@intel.com>
Fixes: 837a3d66 ("selftests: net: Add cross-compilation support for BPF programs")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20221206102838.272584-1-bjorn@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Petr Machata says:

====================
mlxsw: Add Spectrum-1 ip6gre support

Ido Schimmel writes:

Currently, mlxsw only supports ip6gre offload on Spectrum-2 and newer
ASICs. Spectrum-1 can also offload ip6gre tunnels, but it needs double
entry router interfaces (RIFs) for the RIFs representing these tunnels.
In addition, the RIF index needs to be even. This is handled in
patches #1-#3.

The implementation can otherwise be shared between all Spectrum
generations. This is handled in patches #4-#5.

Patch #6 moves a mlxsw ip6gre selftest to a shared directory, as ip6gre
is no longer only supported on Spectrum-2 and newer ASICs.

This work is motivated by users that require multiple GRE tunnels that
all share the same underlay VRF. Currently, mlxsw only supports
decapsulation based on the underlay destination IP (i.e., not taking the
GRE key into account), so users need to configure these tunnels with
different source IPs and IPv6 addresses are easier to spare than IPv4.

Tested using existing ip6gre forwarding selftests.
====================

Link: https://lore.kernel.org/r/cover.1670414573.git.petrm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Now that Spectrum-1 gained ip6gre support we can move the test out of
the Spectrum-2 directory.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As explained in the previous patch, the existing Spectrum-2 ip6gre
implementation can be reused for Spectrum-1. Change the Spectrum-1
ip6gre operations structure to use the common operations.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>