CPU and CODEC DAI probe are performed in exactly the same way. Which means
we can reuse the snd_soc_codec_dai_probe() for probing CPU DAIs as well.

While we are at it also drop the unused card parameter form the function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

The card field of the snd_soc_dai field is very rarely used. We can use
dai->component->card instead and remove the card field from the snd_soc_dai
struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'topic/dapm' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-core

Typically a DAI does not need direct access to the platform. Currently the
only user of this field is in a platform driver where we have a more direct
way of getting a pointer to the platform. This patch updates the driver to
use the more direct way and then removes the platform field from the
snd_soc_dai struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Those are unused and new drivers should use device driver suspend/resume.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

The main ASoC source file is getting quite large and the standard ops don't
really have anything to do with the rest of the file so split them out into
a separate file.
Signed-off-by: Mark Brown <broonie@kernel.org>

Commit f227b88f ("ASoC: core: Add signed register volume control logic")
added support for signed control to the generic volsw control handler.
This makes it possible to use them for the S8 control as well, rather than
having to use a custom control handler implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently we cache the number of input and output paths going to/from a
widget only within a power update sequence. But not in between power update
sequences.

But we know how changes to the DAPM graph affect the number of input (form a
source) and output (to a sink) paths of a widget and only need to
recalculate them if a operation has been performed that might have changed
them.
	* Adding/removing or connecting/disconnecting a path means that the for
	  the source of the path the number of output paths can change and for
	  the sink the number of input paths can change.
	* Connecting/disconnecting a widget has the same effect has connecting/
	  disconnecting all paths of the widget. So for the widget itself the
	  number of inputs and outputs can change, for all sinks of the widget
	  the number of inputs can change and for all sources of the widget the
	  number of outputs can change.
	* Activating/Deactivating a stream can either change the number of
	  outputs on the sources of the widget associated with the stream or the
	  number of inputs on the sinks.

Instead of always invalidating all cached numbers of input and output paths
for each power up or down sequence this patch restructures the code to only
invalidate the cached numbers when a operation that might change them has
been performed. This can greatly reduce the number of DAPM power checks for
some very common operations.

Since per DAPM operation typically only either change the number of inputs
or outputs the number of path checks is reduced by at least 50%. The number
of neighbor checks is also reduced about the same percentage, but since the
number of neighbors encountered when walking from sink to source is not the
same as when walking from source to sink the actual numbers will slightly
vary from card to card (e.g. for a mixer we see 1 neighbor when walking from
source to sink, but the number of inputs neighbors when walking from source
to sink).

Bigger improvements can be observed for widgets with multiple connected
inputs and output (e.g. mixers probably being the most widespread form of
this). Previously we had to re-calculate the number of inputs and outputs
on all input and output paths. With this change we only have to re-calculate
the number of outputs on the input path that got changed and the number of
inputs on the output paths.

E.g. imagine the following example:

	A --> B ----.
	            v
	M --> N --> Z <-- S <-- R
	            |
	            v
	            X

Widget Z has multiple input paths, if any change was made that cause Z to be
marked as dirty the power state of Z has to be re-computed. This requires to
know the number of inputs and outputs of Z, which requires to know the
number of inputs and outputs of all widgets on all paths from or to Z.
Previously this meant re-computing all inputs and outputs of all the path
going into or out of Z. With this patch in place only paths that actually
have changed need to be re-computed.

If the system is idle (or the part of the system affected by the changed
path) the number of path checks drops to either 0 or 1, regardless of how
large or complex the DAPM context is. 0 if there is no connected sink and no
connected source. 1 if there is either a connected source or sink, but not
both. The number of neighbor checks again will scale accordingly and will be
a constant number that is the number of inputs or outputs of the widget for
which we did the path check.

When loading a state file or switching between different profiles typically
multiple mixer and mux settings are changed, so we see the benefit of this
patch multiplied for these kinds of operations.

Testing with the ADAU1761 shows the following changes in DAPM stats for
changing a single Mixer switch for a Mixer with 5 inputs while the DAPM
context is idle.

         Power  Path  Neighbour
Before:  2      12    30
After:   2       1     2

For the same switch, but with a active playback stream the stat changed are
as follows.

         Power  Path  Neighbour
Before:  10     20    54
After:   10      7    21

Cumulative numbers for switching the audio profile which changes 7 controls
while the system is idle:

         Power  Path  Neighbour
Before:  16      80   170
After:   16       7    23

Cumulative numbers for switching the audio profile which changes 7 controls
while playback is active:

         Power  Path  Neighbour
Before:  51     123   273
After:   51      29   109

Starting (or stopping) the playback stream:

         Power  Path  Neighbour
Before:  34     34    117
After:   34     17    69
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Supply widgets are somewhat special and not all kinds of paths to or from
supply widgets make sense. This patch adds a few sanity checks that errors
out during the path instantiation for those invalid paths. This will prevent
drivers to depend on weird behavior resulting from such paths as well as
will allow the DAPM algorithms to assume that they never see such paths.

This patch adds checks for the following three invalid types of paths:
	* A path with a non-supply widget as a source connected to a supply
	  widget as a sink. Such a path has no effect on either of the two
	  connected widgets.
	* Paths with a connected() callback that have a non-supply widget as the
	  source. The DAPM algorithm only uses the conneceted() callback for
	  supply widget power checks. And since it prevents caching of the DAPM
	  state there is no intention to make it more generic as it has
	  negative performance implications.
	* Paths which connect a supply to a mixer or mux via a control. Controls
	  are only meant to affect the routing of audio data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

The state of endpoint widgets is affected by that card's power state.
Endpoint widgets that do no have the ignore_suspend flag set will be
considered inactive during suspend. So they have to be re-checked and marked
dirty after the card's power state changes. Currently the input and output
widgets are marked dirty instead, this works most of the time since
typically a path from one endpoint to another will go via a input or output
widget. But marking the endpoints dirty is technically more correct and will
also work for odd corner cases.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Supply widgets do not count towards the input and output widgets of their
neighbors and for supply widgets themselves we do not care for the number
of input or output paths. This means that a path that connects to a supply
widget effectively behaves the same as a path that as the weak property set.
This patch adds a new path flag that gets set to true when the path is
connected to at least one supply widget. If a path with the flag set is
encountered in is_connected_{input,output}_ep() is is skipped in the same
way that weak paths are skipped. This slightly brings down the number of
path checks.

Since both the weak and the supply flag are implemented as bitfields which
are stored in the same word there is no runtime overhead due to checking
both rather than just one and also the size of the path struct is not
increased by this patch. Another advantage is that we do not have to handle
supply widgets in is_connected_{input,output}_ep() anymore since it will
never be called for supply widgets. The only exception is from
dapm_widget_power_read_file() where a check is added to special case supply
widgets.

Testing with the ADAU1761, which has a handful of supply widgets, shows the
following changes in the DAPM stats for a playback stream start.

         Power  Path  Neighbour
Before:  34     78    117
After:   34     48    117
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

DAPM widgets can be classified into four categories:
	* supply: Supply widgets do not affect the power state of their
		non-supply widget neighbors and unlike other widgets a
		supply widget is not powered up when it is on an active
		path, but when at least on of its neighbors is powered up.
	* source: A source is a widget that receives data from outside the
		DAPM graph or generates data. This can for example be a
		microphone, the playback DMA or a signal generator. A source
		widget will be considered powered up if there is an active
		path to a sink widget.
	* sink: A sink is a widget that transmits data to somewhere outside
		of the DAPM graph. This can e.g. be a speaker or the capture
		DMA. A sink widget will be considered powered up if there is
		an active path from a source widget.
	* normal: Normal widgets are widgets not covered by the categories
		above. A normal widget will be considered powered up if it
		is on an active path between a source widget and a sink
		widget.

The way the number of input and output paths for a widget is calculated
depends on its category. There are a bunch of factors which decide which
category a widget is. Currently there is no formal classification of these
categories and we calculate the category of the widget based on these
factors whenever we want to know it. This is at least once for every widget
during each power update sequence. The factors which determine the category
of the widgets are mostly static though and if at all change rather seldom.
This patch introduces three new per widget flags, one for each of non-normal
widgets categories. Instead of re-computing the category each time we want
to know them the flags will be checked. For the majority of widgets the
category is solely determined by the widget id, which means it never changes
and only has to be set once when the widget is created. The only widgets
with dynamic categories are:

	snd_soc_dapm_dai_out: Is considered a sink iff the capture stream is
		active, otherwise normal.
	snd_soc_dapm_dai_in: Is considered a source iff the playback stream
		is active, otherwise normal.
	snd_soc_dapm_input: Is considered a sink iff it has no outgoing
		paths, otherwise normal.
	snd_soc_dapm_output: Is considered a source iff it has no incoming
		paths, otherwise normal.
	snd_soc_dapm_line: Is considered a sink iff it has no outgoing paths
		and is considered a source iff it has no incoming paths,
		otherwise normal.

For snd_soc_dapm_dai_out/snd_soc_dapm_dai_in widgets the category will be
updated when a stream is started or stopped. For the other dynamic widgets
the category will be updated when a path connecting to it is added or
removed.

Introducing those new widget categories allows to make
is_connected_{output,input}_ep, which are among the hottest paths of the
DAPM algorithm, more generic and significantly shorter.

The before and after sizes for is_connected_{output,input}_ep are:

On ARM (defconfig + CONFIG_SND_SOC):
	function                                     old     new   delta
	is_connected_output_ep                       480     340    -140
	is_connected_input_ep                        456     352    -104

On amd64 (defconfig + CONFIG_SND_SOC):
	function                                     old     new   delta
	is_connected_output_ep                       579     427    -152
	is_connected_input_ep                        563     427    -136

Which is about a 25%-30% decrease, other architectures are expected to have
similar numbers. At the same time the size of the snd_soc_dapm_widget struct
does not change since the new flags are stored in the same word as the
existing flags.

Note: that since the per widget 'ext' flag was only used to decide whether a
snd_soc_dapm_input or snd_soc_dapm_output widget was a source or a sink it
is now unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Controls on a path only have an effect if the sink on the path is either a
mixer or mux widget. Currently we sort of silently ignore controls on other
paths, but since they don't do anything having them on other paths does not
make much sense and it is probably safe to assume that if we see such a path
it is a mistake in the driver that registered the path. This patch modifies
snd_soc_dapm_add_path() to report an error if a path with and control is
encountered where we didn't expect a control. This also allows to simplify
the code quite a bit.

The patch also moves the connecting of the path lists out of
dapm_connect_mux() and dapm_connect_mixer() into snd_soc_dapm_add_path().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Paths that are directly connected to a MUX widget are not affected by
changes to the MUX's control. Rather than checking if a path is directly
connected each time the MUX is updated do it only once when MUX is created.

We can also remove the check for e->texts[mux] != NULL, since if that
condition was true the code would have had already crashed much earlier (And
generally speaking if a enum's 'texts' entry is NULL it's a bug in the
driver).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Rework soc_dapm_{mixer,mux}_update_power() to only mark a path dirty if the
connect state if the path has actually changed. This avoids unnecessary
power state checks for the widgets involved.

Also factor out the common code that is involved in this into a helper
function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

The 'walked' flag was used to avoid walking paths that have already been
walked. But since we started caching the number of inputs and outputs of a
path we never actually get into a situation where we try to walk a path that
has the 'walked' flag set.

There are two cases in which we can end up walking a path multiple times
within a single run of is_connected_output_ep() or is_connected_input_ep().

1) If a path splits up and rejoins later:

	     .--> C ---v
	A -> B         E --> F
	     '--> D ---^

When walking from A to F we'll end up at E twice, once via C and once via D.
But since we do a depth first search we'll fully discover the path and
initialize the number of outputs/inputs of the widget the first time we get
there. The second time we get there we'll use the cached value and not
bother to check any of the paths again. So we'll never see a path where
'walked' is set in this case.

2) If there is a circle:

	A --> B <-- C <-.--> F
	      '--> D ---'

When walking from A to F we'll end up twice at B. But since there is a
circle the 'walking' flag will still be set on B once we get there the
second time. This means we won't look at any of it's outgoing paths. So in
this case we won't ever see a path where 'walked' is set either.

So it is safe to remove the flag. This on one hand means we remove some
always true checks from one of the hottest paths of the DAPM algorithm and
on the other hand means we do not have to do the tedious clearing of the
flag after checking the number inputs or outputs of a widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

dapm_adc_check_power() checks if the widget is active, if yes it only checks
whether there are any connected input paths. Otherwise it calls
dapm_generic_check_power() which will check for both connected input and
output paths. But the function that checks for connected output paths will
return true if the widget is a active sink. Which means the generic power
check function will work just fine and there is no need for a special power
check function.

The same applies for dapm_dac_check_power(), but with input and output paths
reversed.

This patch removes both dapm_adc_check_power() and dapm_dac_check_power()
and replace their usage with dapm_generic_check_power().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

A path has always a valid source and a valid sink otherwise we wouldn't add
it in the first place. Hence all tests that check if sink/source is non NULL
always evaluate to true and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Each widget has a list of all the paths that it is connected to. There is no
need to iterate over all paths when we are only interested in the paths of a
specific widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

... and reduce the open codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Both path->name and e->texts[i] have type const char*, so the cast is
slightly confusing and certainly unnecessary.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

We call mute for codec dai only, we should call this for cpu dai as well to
allow cpu dais (FEs) in DSPs to be muted/unmuted on shutdown/startup
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull ARM SoC fixes from Olof Johansson:
 "A batch of fixes that have come in during the merge window.

  Some of them are defconfig updates for things that have now landed,
  some errata additions and a few general scattered fixes.

  There's also a qcom DT update that adds support for SATA on AP148, and
  basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
  isolated enough that we could merge it even if it's late"

* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: corrected bcm2835 search
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148
  MAINTAINERS: Update Santosh Shilimkar's email id
  ARM: sunxi_defconfig: enable CONFIG_REGULATOR
  ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
  ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
  ARM: exynos_defconfig: enable USB gadget support
  ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
  ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
  ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
  ARM: SAMSUNG: Restore Samsung PM Debug functionality
  ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
  ARM: exynos_defconfig: Enable SBS battery support
  ARM: exynos_defconfig: Enable Control Groups support
  ARM: exynos_defconfig: Enable Atmel maXTouch support
  ARM: exynos_defconfig: Enable MAX77802

Pull audit updates from Eric Paris:
 "So this change across a whole bunch of arches really solves one basic
  problem.  We want to audit when seccomp is killing a process.  seccomp
  hooks in before the audit syscall entry code.  audit_syscall_entry
  took as an argument the arch of the given syscall.  Since the arch is
  part of what makes a syscall number meaningful it's an important part
  of the record, but it isn't available when seccomp shoots the
  syscall...

  For most arch's we have a better way to get the arch (syscall_get_arch)
  So the solution was two fold: Implement syscall_get_arch() everywhere
  there is audit which didn't have it.  Use syscall_get_arch() in the
  seccomp audit code.  Having syscall_get_arch() everywhere meant it was
  a useless flag on the stack and we could get rid of it for the typical
  syscall entry.

  The other changes inside the audit system aren't grand, fixed some
  records that had invalid spaces.  Better locking around the task comm
  field.  Removing some dead functions and structs.  Make some things
  static.  Really minor stuff"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: rename audit_log_remove_rule to disambiguate for trees
  audit: cull redundancy in audit_rule_change
  audit: WARN if audit_rule_change called illegally
  audit: put rule existence check in canonical order
  next: openrisc: Fix build
  audit: get comm using lock to avoid race in string printing
  audit: remove open_arg() function that is never used
  audit: correct AUDIT_GET_FEATURE return message type
  audit: set nlmsg_len for multicast messages.
  audit: use union for audit_field values since they are mutually exclusive
  audit: invalid op= values for rules
  audit: use atomic_t to simplify audit_serial()
  kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
  audit: reduce scope of audit_log_fcaps
  audit: reduce scope of audit_net_id
  audit: arm64: Remove the audit arch argument to audit_syscall_entry
  arm64: audit: Add audit hook in syscall_trace_enter/exit()
  audit: x86: drop arch from __audit_syscall_entry() interface
  sparc: implement is_32bit_task
  sparc: properly conditionalize use of TIF_32BIT
  ...

Merge tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes

Merge "qcom DT changes for v3.18-3" from Kumar Gala:

Qualcomm ARM Based Device Tree Updates for v3.18-3

* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148

* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148

Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Pull more fixes from Kukjin Kim:

2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
  and exynos5420-arndale-octa boards, because the USB dwc3 controller
  will not work properly without dr_mode as host on above boards if
  the USB host and gadget are enabled in kernel configuration both.

* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>

Corrected bcm2835 maintainer info by using N: to specify any files with
bcm2835 in are directed to the proper maintainer.
Also corrected minor mispelling of ARCHITECTURE in 2 comment locations.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ntb (non-transparent bridge) updates from Jon Mason:
 "Add support for Haswell NTB split BARs, a debugfs entry for basic
  debugging info, and some code clean-ups"

* tag 'ntb-3.18' of git://github.com/jonmason/ntb:
  ntb: Adding split BAR support for Haswell platforms
  ntb: use errata flag set via DID to implement workaround
  ntb: conslidate reading of PPD to move platform detection earlier
  ntb: move platform detection to separate function
  NTB: debugfs device entry

Pull i2c updates from Wolfram Sang:
 "Highlights from the I2C subsystem for 3.18:

   - new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.

   - designware driver gained AMD support, exynos gained exynos7 support

  The rest is usual driver stuff.  Hopefully no lowlights this time"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i801: Add Device IDs for Intel Sunrise Point PCH
  i2c: hix5hd2: add i2c controller driver
  i2c-imx: Disable the clock on probe failure
  i2c: designware: Add support for AMD I2C controller
  i2c: designware: Rework probe() to get clock a bit later
  i2c: designware: Default to fast mode in case of ACPI
  i2c: axxia: Add I2C driver for AXM55xx
  i2c: exynos: add support for HSI2C module on Exynos7
  i2c: mxs: detect No Slave Ack on SELECT in PIO mode
  i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
  i2c: cros-ec-tunnel: Add of match table
  i2c: rcar: remove sign-compare flaw
  i2c: ismt: Use minimum descriptor size
  i2c: imx: Add arbitration lost check
  i2c: rk3x: Remove unlikely() annotations
  i2c: rcar: check for no IRQ in rcar_i2c_irq()
  i2c: rcar: make rcar_i2c_prepare_msg() *void*
  i2c: rcar: simplify check for last message
  i2c: designware: add support of platform data to set I2C mode
  i2c: designware: add support of I2C standard mode

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes after 3.18 merge.

  The urgent one is the fix for kernel panics with linked PCM substream
  triggered by the recent nonatomic PCM ops support.  Other two fixes
  (emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
  a new Intel HD-audio controller"

* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
  ALSA: emu10k1: Fix deadlock in synth voice lookup
  ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
  ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88

Pull second round of input updates from Dmitry Torokhov:
 "Mostly simple bug fixes, although we do have one brand new driver for
  Microchip AR1021 i2c touchscreen.

  Also there is the change to stop trying to use i8042 active
  multiplexing by default (it is still possible to activate it via
  i8042.nomux=0 on boxes that implement it)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - add Thrustmaster as Xbox 360 controller vendor
  Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
  Input: max77693-haptic - fix state check in imax77693_haptic_disable()
  Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
  Input: alps - fix v4 button press recognition
  Input: i8042 - disable active multiplexing by default
  Input: i8042 - add noloop quirk for Asus X750LN
  Input: synaptics - gate forcepad support by DMI check
  Input: Add Microchip AR1021 i2c touchscreen
  Input: cros_ec_keyb - add of match table
  Input: serio - avoid negative serio device numbers
  Input: avoid negative input device numbers
  Input: automatically set EV_ABS bit in input_set_abs_params
  Input: adp5588-keys - cancel workqueue in failure path
  Input: opencores-kbd - switch to using managed resources
  Input: evdev - fix EVIOCG{type} ioctl

Pull infiniband/RDMA updates from Roland Dreier:
 - large set of iSER initiator improvements
 - hardware driver fixes for cxgb4, mlx5 and ocrdma
 - small fixes to core midlayer

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
  RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line
  RDMA/cxgb4: Add missing neigh_release in find_route
  RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss
  RDMA/cxgb4: Make c4iw_wr_log_size_order static
  IB/core: Fix XRC race condition in ib_uverbs_open_qp
  IB/core: Clear AH attr variable to prevent garbage data
  RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis
  RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it
  RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc()
  RDMA/ocrdma: Remove a unused-label warning
  RDMA/ocrdma: Convert kernel VA to PA for mmap in user
  RDMA/ocrdma: Get vlan tag from ib_qp_attrs
  RDMA/ocrdma: Add default GID at index 0
  IB/mlx5, iser, isert: Add Signature API additions
  Target/iser: Centralize ib_sig_domain setting
  IB/iser: Centralize ib_sig_domain settings
  IB/mlx5: Use extended internal signature layout
  IB/iser: Set IP_CSUM as default guard type
  IB/iser: Remove redundant assignment
  IB/mlx5: Use enumerations for PI copy mask
  ...

Pull more perf updates from Ingo Molnar:
 "A second (and last) round of late coming fixes and changes, almost all
  of them in perf tooling:

  User visible tooling changes:

   - Add period data column and make it default in 'perf script' (Jiri
     Olsa)

   - Add a visual cue for toggle zeroing of samples in 'perf top'
     (Taeung Song)

   - Improve callchains when using libunwind (Namhyung Kim)

  Tooling fixes and infrastructure changes:

   - Fix for double free in 'perf stat' when using some specific invalid
     command line combo (Yasser Shalabi)

   - Fix off-by-one bugs in map->end handling (Stephane Eranian)

   - Fix off-by-one bug in maps__find(), also related to map->end
     handling (Namhyung Kim)

   - Make struct symbol->end be the first addr after the symbol range,
     to make it match the convention used for struct map->end.  (Arnaldo
     Carvalho de Melo)

   - Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat
     live' (Jiri Olsa)

   - Fix python test build by moving callchain_param to an object linked
     into the python binding (Jiri Olsa)

   - Document sysfs events/ interfaces (Cody P Schafer)

   - Fix typos in perf/Documentation (Masanari Iida)

   - Add missing 'struct option' forward declaration (Arnaldo Carvalho
     de Melo)

   - Add option to copy events when queuing for sorting across cpu
     buffers and enable it for 'perf kvm stat live', to avoid having
     events left in the queue pointing to the ring buffer be rewritten
     in high volume sessions.  (Alexander Yarygin, improving work done
     by David Ahern):

   - Do not include a struct hists per perf_evsel, untangling the
     histogram code from perf_evsel, to pave the way for exporting a
     minimalistic tools/lib/api/perf/ library usable by tools/perf and
     initially by the rasd daemon being developed by Borislav Petkov,
     Robert Richter and Jean Pihet.  (Arnaldo Carvalho de Melo)

   - Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and
     thread maps mean syswide monitoring, reducing the boilerplate for
     tools that only want system wide mode.  (Arnaldo Carvalho de Melo)

   - Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
     should be just a front end for exit + free (Arnaldo Carvalho de
     Melo)

   - Add support to new style format of kernel PMU event.  (Kan Liang)

  and other misc fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
  perf script: Add period as a default output column
  perf script: Add period data column
  perf evsel: No need to drag util/cgroup.h
  perf evlist: Add missing 'struct option' forward declaration
  perf evsel: Move exit stuff from __delete to __exit
  kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define
  perf kvm stat live: Enable events copying
  perf session: Add option to copy events when queueing
  perf Documentation: Fix typos in perf/Documentation
  perf trace: Use thread_{,_set}_priv helpers
  perf kvm: Use thread_{,_set}_priv helpers
  perf callchain: Create an address space per thread
  perf report: Set callchain_param.record_mode for future use
  perf evlist: Fix for double free in tools/perf stat
  perf test: Add test case for pmu event new style format
  perf tools: Add support to new style format of kernel PMU event
  perf tools: Parse the pmu event prefix and suffix
  Revert "perf tools: Default to cpu// for events v5"
  perf Documentation: Remove Ruplicated docs for powerpc cpu specific events
  perf Documentation: sysfs events/ interfaces
  ...

Pull sparc fixes from David Miller:
 "Here we have two bug fixes:

  1) The current thread's fault_code is not setup properly upon entry to
     do_sparc64_fault() in some paths, leading to spurious SIGBUS.

  2) Don't use a zero length array at the end of thread_info on sparc64,
     otherwise end_of_stack() isn't right"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Do not define thread fpregs save area as zero-length array.
  sparc64: Fix corrupted thread fault code.

Pull networking fixes from David Miller:
 "A quick batch of bug fixes:

  1) Fix build with IPV6 disabled, from Eric Dumazet.

  2) Several more cases of caching SKB data pointers across calls to
     pskb_may_pull(), thus referencing potentially free'd memory.  From
     Li RongQing.

  3) DSA phy code tests operation presence improperly, instead of going:

        if (x->ops->foo)
                r = x->ops->foo(args);

     it was going:

        if (x->ops->foo(args))
                r = x->ops->foo(args);

   Fix from Andew Lunn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  Net: DSA: Fix checking for get_phy_flags function
  ipv6: fix a potential use after free in sit.c
  ipv6: fix a potential use after free in ip6_offload.c
  ipv4: fix a potential use after free in gre_offload.c
  tcp: fix build error if IPv6 is not enabled

The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6819563e ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This breaks the stack end corruption detection facility.

What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.

"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.

So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.

Fix this by making the size explicit.

Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves.  So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.

Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:

1) For pre-hypervisor TLB protection violation traps, if we took
   the 'winfix_trampoline' path we wouldn't have %g4 initialized
   with the FAULT_CODE_* value yet.  Resulting in using the
   TLB_TAG_ACCESS register address value instead.

2) In the TSB miss path, when we notice that we are going to use a
   hugepage mapping, but we haven't allocated the hugepage TSB yet, we
   still have to take the window fixup case into consideration and
   in that particular path we leave %g4 not setup properly.

Errors on this sort were largely invisible previously, but after
commit 4ccb9272 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.

FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.

Fixes: 4ccb9272 ("sparc64: sun4v TLB error power off events")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull slave-dmaengine updates from Vinod Koul:
 "For dmaengine contributions we have:
   - designware cleanup by Andy
   - my series moving device_control users to dmanegine_xxx APIs for
     later removal of device_control API
   - minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
     etc"

* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
  serial: atmel: add missing dmaengine header
  dmaengine: remove FSLDMA_EXTERNAL_START
  dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
  carma-fpga: move to fsl_dma_external_start()
  carma-fpga: use dmaengine_xxx() API
  dmaengine: freescale: add and export fsl_dma_external_start()
  dmaengine: add dmaengine_prep_dma_sg() helper
  video: mx3fb: use dmaengine_terminate_all() API
  serial: sh-sci: use dmaengine_terminate_all() API
  net: ks8842: use dmaengine_terminate_all() API
  mtd: sh_flctl: use dmaengine_terminate_all() API
  mtd: fsmc_nand: use dmaengine_terminate_all() API
  V4L2: mx3_camer: use dmaengine_pause() API
  dmaengine: coh901318: use dmaengine_terminate_all() API
  pata_arasan_cf: use dmaengine_terminate_all() API
  dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
  dmaengine: dw: export probe()/remove() and Co to users
  dmaengine: dw: enable and disable controller when needed
  dmaengine: dw: always export dw_dma_{en,dis}able
  dmaengine: dw: introduce dw_dma_on() helper
  ...