Some tags used in the firmware patch file are inconsistent with hwdep
sysfs file names, such as, the firmware patch takes [hint] tag while
sysfs file is */hints.  This makes even me referring back to the
document often.  Let's provide the same tag names as sysfs for
reducing confusions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just a code refactoring: the need_codec flag in hda_patch_item struct
can be removed by checking the current mode instead.  No functional
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It turned out that some AMD HDMI controllers still don't provide
proper values in GCAP register (all zero), and the driver assigns only
one stream in that case, although the connected codec chip supports
more than one stream.

In this patch, the default max number of streams for AMD HDMI
controllers is increased to 8, which  should suffice for most use
cases.  The overhead by this increase is more azx_dev struct and BDL
allocations, so it's negligible.  Of course, if the controller
provides a proper GCAP register, the register value would be used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

this gives ability to convey the valid values of supported rates in
sample_rates array
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now that we don't use SNDRV_PCM_RATE_xxx bit fields for sample rate, we need to
change the description to an array for describing the sample rates supported by
the sink/source
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

commit f0e9c080 - "ALSA: compress: change the way sample rates are sent to
kernel" changed the way sample rates are sent. So now we don't need to check for
PCM_RATE_xxx in kernel
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The lack of comma leads to the wrong channel for an SPDIF channel.
Unfortunately this wasn't caught by compiler because it's still a
valid expression.
Reported-by: Alexander Aristov <aristov.alexander@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression pdev;
@@

pci_set_power_state(pdev,
- 3
+ PCI_D3hot
 )
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This motherboard seems to have a flaky jack detection - when the
front HP is not present, the jack state quickly switches on and off.

This has been reported by three people in the bug, so I doubt it's
a user error this time.

BugLink: https://bugs.launchpad.net/bugs/1248116Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: Updates  for v3.14

Not a lot going on framework wise, partly due to Christmas at least in
the case of the work I've been doing, but there's been quite a lot of
cleanup activity going on and the usual trickle of new drivers:

 - Update to the generic DMA code to support deferred probe and managed
   resources.
 - New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
   and Analog Devices AXI I2S and S/PDIF controller IPs.
 - Device tree support for the simple card, max98090 and cs42l52.
 - Conversion of the Samsung drivers to native dmaengine, making them
   multiplatform compatible and hopefully helping keep them more modern
   and up to date.
 - More regmap conversions, including a very welcome one for twl6040
   from Peter Ujfalusi.
 - A big overhaul of the DaVinci drivers also from Peter Ujfalusi.

Merge remote-tracking branches 'asoc/topic/ad1836', 'asoc/topic/ad193x', 'asoc/topic/adav80x', 'asoc/topic/adsp', 'asoc/topic/ak4641', 'asoc/topic/ak4642', 'asoc/topic/arizona', 'asoc/topic/atmel', 'asoc/topic/au1x', 'asoc/topic/axi', 'asoc/topic/bcm2835', 'asoc/topic/blackfin', 'asoc/topic/cs4271', 'asoc/topic/cs42l52', 'asoc/topic/da7210', 'asoc/topic/davinci', 'asoc/topic/ep93xx', 'asoc/topic/fsl', 'asoc/topic/fsl-mxs', 'asoc/topic/generic', 'asoc/topic/hdmi', 'asoc/topic/jack', 'asoc/topic/jz4740', 'asoc/topic/max98090', 'asoc/topic/mxs', 'asoc/topic/omap', 'asoc/topic/pxa', 'asoc/topic/rcar', 'asoc/topic/s6000', 'asoc/topic/sai', 'asoc/topic/samsung', 'asoc/topic/sgtl5000', 'asoc/topic/spear', 'asoc/topic/ssm2518', 'asoc/topic/ssm2602', 'asoc/topic/tegra', 'asoc/topic/tlv320aic3x', 'asoc/topic/twl6040', 'asoc/topic/txx9', 'asoc/topic/uda1380', 'asoc/topic/width', 'asoc/topic/wm8510', 'asoc/topic/wm8523', 'asoc/topic/wm8580', 'asoc/topic/wm8711', 'asoc/topic/wm8728', 'asoc/topic/wm8731', 'asoc/topic/wm8741', 'asoc/topic/wm8750', 'asoc/topic/wm8753', 'asoc/topic/wm8776', 'asoc/topic/wm8804', 'asoc/topic/wm8900', 'asoc/topic/wm8901', 'asoc/topic/wm8940', 'asoc/topic/wm8962', 'asoc/topic/wm8974', 'asoc/topic/wm8985', 'asoc/topic/wm8988', 'asoc/topic/wm8990', 'asoc/topic/wm8991', 'asoc/topic/wm8994', 'asoc/topic/wm8995', 'asoc/topic/wm9081' and 'asoc/topic/x86' into asoc-next

Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>

ffs() returns the bit position from 1, while the ssm2158 driver code
assumes it being 0-based.  Also, the bit mask computation of the two
channel slots are incorrect; it must have worked just casually.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>

Try to get the device's module clock if the dt has no clocks and
system-clock-frequency properties.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

This is a quick fix for the below two issues when building spdif as modules.

1) If modprobing modules in order: (Step 1) snd-soc-fsl-spdif -> (Step 2)
snd-soc-imx-spdif -> (Step 3) snd-soc-spdif-tx/rx, we will fail to create
imx-spdif card and dai link unless we rmmod snd-soc-imx-spdif and modprobe
it again due to the execution platform_driver_unregister() in probe() when
meeting -EPROBE_DEFER at Step 2.

2) After "imx-spdif sound-spdif.17: dit-hifi <-> 2004000.spdif mapping ok",
'rmmod snd-soc-imx-spdif' would cause kernel dump with warning:
WARNING: CPU: 0 PID: 1301 at /home/rmk/git/linux-rmk/fs/sysfs/dir.c:915 sysfs_hash_and_remove+0x84/0x90()
sysfs: can not remove 'dapm_widget', no directory
This should be caused by disordered resourse releasing of the whole link.
And trying to unregister the card and then CODEC dev can't fix this issue.

Thus this patch just provides a simple fix to these two bugs by using the
snd-soc-dummy in the core instead of seperate snd-soc-spdif-tx/rx so that
there's no need to handle the registering and unregistering of CODEC or
CODEC dai any more.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

From "ASoC: make snd_soc_dai_link more symmetrical", can we see that
the name of CPU DAI maybe omitted. If the DAI name is omitted, try to
use the component name instead.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

This patch adds SRC support to Renesas sound driver.
SRC converts sampling rate between codec <-> cpu.
It needs special codec chip,
or very simple DA/AD converter to use it.
This patch was tested via ak4554 codec,
and supports Gen1 only at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.

This patch cleanup it with focusing about SRC and Gen2 part.

ssi clock which is calculated from rsnd_ssi_master_clk_start()
should have flexibility since Renesas sound has
SRC (= Sampling Rate Converter).
But current implementation is using runtime->rate directly.
This patch tidyup rsnd_ssi_master_clk_start() parameter
as preparation of future SRC support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.

This patch cleanup it with focusing about SRC and Gen2 part.

rsnd_scu_set_hpbif() is renamed to rsnd_scu_rate_ctrl(),
since its naming doesn't indicate the function meaning.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

INT_ENABLE is needed only Gen2.
rsnd_mod_write() do nothing on Gen1, but it is confusable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.

This patch cleanup it with focusing about SRC and Gen2 part.

SRC_CTRL/BUSIF_MODE are used for transfer start.
This patch adds rsnd_scu_transfer_start() and merge these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.

This patch cleanup it with focusing about SRC and Gen2 part.

rsnd_scu_set_route() is needed only Gen1.

This patch renames it to rsnd_scu_set_route_if_gen1()
and it adds comment to rsnd_reg member
in order to clarify it is used for Gen1.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

This driver is assuming that
RBGA is used as source clock of 44.1kHz category, and
RBGB is used as source clock of 48kHz category.
This patch clarifies the variable name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Use correct register name which appears in the datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

we can check rsnd_ssi_init(), not, rsnd_ssi_start()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

This patch adds rsnd_adg_set_ssi_clk() to access to
AUDIO_CLK_SEL0/1/2, and removes last user of
rsnd_write/read/bset which is very low level function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Signed-off-by: Jyri Sarha <jsarha@ti.com>
cc: bcousson@baylibre.com
Signed-off-by: Mark Brown <broonie@linaro.org>

The ret parameter is always equal to zero till here.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Parses a simple DAPM route table from device tree.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

When call snd_soc_register_card, it will set driver data to this
device through dev_set_drvdata, then in driver, no need to call
platform_set_drvdata again, so remove it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Revert the SAI's endianess for fifo data to/from DMA engine.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

This is maybe one bug or a limitation of the hardware that the {T,R}CR2's
Synchronous Mode bits must be set as late as possible, or the SAI device
maybe hanged up, and there has not any explaination about this limitation
in the SAI Data Sheet.

And the {T,R}CR2's Synchronous Mode bits must be set at the same time whether
for Tx or Rx stream.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>