Add support to inet v4 raw sockets for binding to nonlocal addresses
through the IP_FREEBIND and IP_TRANSPARENT socket options, as well as
the ipv4.ip_nonlocal_bind kernel parameter.

Add helper function to inet_sock.h to check for bind address validity on
the base of the address type and whether nonlocal address are enabled
for the socket via any of the sockopts/sysctl, deduplicating checks in
ipv4/ping.c, ipv4/af_inet.c, ipv6/af_inet6.c (for mapped v4->v6
addresses), and ipv4/raw.c.

Add test cases with IP[V6]_FREEBIND verifying that both v4 and v6 raw
sockets support binding to nonlocal addresses after the change. Add
necessary support for the test cases to nettest.
Signed-off-by: Riccardo Paolo Bestetti <pbl@bestov.io>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211117090010.125393-1-pbl@bestov.ioSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This is needed for some arches, as reported by Geert Uytterhoeven,
Randy Dunlap and Stephen Rothwell

Fixes: 4721031c ("net: move gro definitions to include/net/gro.h")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211117100130.2368319-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

txq_trans_cond_update() takes netdev_tx_queue *nq,
not nq->trans_start.

Fixes: 5337824f ("net: annotate accesses to queue->trans_start")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211117152917.3739-1-alexandr.lobakin@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Eric Dumazet says:

====================
net: make dev_watchdog() less intrusive

dev_watchdog() is used on many NIC to periodically monitor TX queues
to detect hangs.

Problem is : It stops all queues, then check them, then 'unfreeze' them.

Not only this stops feeding the NIC, it also migrates all qdiscs
to be serviced on the cpu calling netif_tx_unlock(), causing
a potential latency artifact.

With many TX queues, this is becoming more visible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason for stopping all TX queues from dev_watchdog()

Not only this stops feeding the NIC, it also migrates all qdiscs
to be serviced on the cpu calling netif_tx_unlock(), causing
a potential latency artifact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are not fast path, there is no point in inlining them.

Also provide netif_freeze_queues()/netif_unfreeze_queues()
so that we can use them from dev_watchdog() in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In following patches, dev_watchdog() will no longer stop all queues.
It will read queue->trans_start locklessly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tx_timeout_show() assumed dev_watchdog() would stop all
the queues, to fetch queue->trans_timeout under protection
of the queue->_xmit_lock.

As we want to no longer disrupt transmits, we use an
atomic_long_t instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: david decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'for-net-next-2021-11-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Luiz Augusto von Dentz says:

====================
bluetooth-next pull request for net-next:

 - Add support for AOSP Bluetooth Quality Report
 - Enables AOSP extension for Mediatek Chip (MT7921 & MT7922)
 - Rework of HCI command execution serialization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the used PHYs also support hardware timestamping, all configuration requests
should be forwared to the PHYs instead of being processed by the MAC driver
itself.

This enables PHY timestamping in combination with the cpsw driver.

Tested with an am335x based board with two DP83640 PHYs connected to the cpsw
switch.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update net_failover documentation with missing and incomplete
details to get a proper working setup.
Signed-off-by: Vasudev Kamath <vasudev@copyninja.info>
Reviewed-by: Krishna Kumar <krikku@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: ocelot_net: phylink validate implementation updates

This series converts ocelot_net to fill in the supported_interfaces
member of phylink_config, cleans up the validate() implementation,
and then converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ocelot_net has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate the phy interface mode bitmap for the MSCC Ocelot driver with
the interface modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: mtk_eth_soc: phylink validate implementation updates

This series converts mtk_eth_soc to fill in the supported_interfaces
member of phylink_config, cleans up the validate() implementation, and
then converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

mtk_eth_soc has no special behaviour in its validation implementation,
so can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have a better method to select SFP interface modes, we
no longer need to use phylink_helper_basex_speed() in a driver's
validation function, and we can also get rid of our hack to indicate
both 1000base-X and 2500base-X if the comphy is present to make that
work. Remove this hack and use of phylink_helper_basex_speed().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode, nor handle
PHY_INTERFACE_MODE_NA in the validation function. Remove these to
simplify the implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate the phy interface mode bitmap for the Mediatek driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: sparx5: phylink validate implementation updates

This series converts sparx5 to fill in the supported_interfaces member
of phylink_config, cleans up the validate() implementation, and then
converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparx5 has no special behaviour in its validation implementation, so can
be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

sparx5_phylink_validate() no longer needs to check for
PHY_INTERFACE_MODE_NA as phylink will walk the supported interface
types to discover the link mode capabilities. Neither is it necessary
to check the device capabilities as we will not be called for
unsupported interface modes. Remove these checks.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate the phy_interface_t bitmap for the Microchip Sparx5 driver
with interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: enetc: phylink validate implementation updates

This series converts enetc to fill in the supported_interfaces member
of phylink_config, cleans up the validate() implementation, and then
converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

enetc has no special behaviour in its validation implementation, so can
be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate the phy_interface_t bitmap for the Freescale enetc driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: xilinx: phylink validate implementation updates

This series converts axienet to fill in the supported_interfaces member
of phylink_config, cleans up the validate() implementation, and then
converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

axienet has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate the phy_interface_t bitmap for the Xilinx axienet driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2021-11-16

Updates for mlx5 driver:

1) Support ethtool cq mode
2) Static allocation of mod header object for the common case
3) TC support for when local and remote VTEPs are in the same
4) Create E-Switch QoS objects on demand to save on resources
5) Minor code improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't create eswitch QoS (root TSAR) on switch mode change. Create it on
first child TSAR object creation - vport or rate group. Keep track
root TSAR references and release root TSAR with last object deletion.
No need to check for QoS is enabled when installing tc matchall filter.
Remove related helper function due to no users of it.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Vports' QoS is not commonly used but consume SW/HW resources, which
becomes an issue on BlueField SoC systems.
Don't enable QoS on vports by default on eswitch mode change and enable
when it's going to be used by one of the top level users:
- configuring TC matchall filter with police action;
- setting rate with legacy NDO API;
- calling devlink ops->rate_leaf_*() callbacks.

Disable vport QoS on vport cleanup.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

eswitch.c is mainly for common code between legacy and offloads mode.
MAC address get and set via devlink is applicable only in offloads mode.

Hence, move it to eswitch_offloads.c file.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

mlx5_eswitch_set_vport_mac() routine already does necessary checks which
are duplicated in implementation of
mlx5_devlink_port_function_hw_addr_set().

Hence, reuse mlx5_eswitch_set_vport_mac() and cut down the code.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

An eswitch vport of the devlink port is always enabled before a
devlink port is registered. And a eswitch vport is always disabled
after a devlink port is unregistered.
Hence avoid the vport enabled check in the devlink callback routine.
Such check is only applicable in the legacy SR-IOV callbacks.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Sunil Sudhakar Rani <sunrani@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

There is a use case that the local and remote VTEPs are in the same
host. Currently, the out ifindex is not specified when looking up the
decap route for offloads. So in this case, a local route is returned
and the route dev is lo.

Actual tunnel interface can be created with a parameter "dev" [1],
which specifies the physical device to use for tunnel endpoint
communication. Pass this parameter to driver when looking up decap
route for offloads. So that a unicast route will be returned.

[1] ip link add name vxlan1 type vxlan id 100 dev enp4s0f0 remote 1.1.1.1 dstport 4789
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Move the comment to the correct place where the driver actually
removes the flag and not in the check that maybe pedit actions exists.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>