Fix wording based on checkpatch.pl
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

E.g. pm_runtime_set_active must be called while the power
management system is disabled. Fixes extra hanging clk_enable.
Signed-off-by: Topi Kuutela <topi.kuutela@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Do not print error in case of EPROBE_DEFER.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Under certain conditions, Cadence's I2C controller's transfer_size
register will roll over and generate invalid read transactions. Before
this change, the ISR relied solely on the RXDV bit to determine when to
write more data to the user's buffer. The invalid read data would cause
overruns, smashing stacks and worse.

This change stops the buffer writes to the requested boundary and
reports the error. The controller will be reset so normal transactions
may resume.
Signed-off-by: Alex Williams <alex.williams@ni.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> # in a seperate mail
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add support for Intel Comet Lake PCH-V which is based on Intel Kaby
Lake. Difference between it and other Comet Lake variants is that former
uses previous iTCO version 4 and latter use version 6 like Intel Cannon
Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In I2C there is no such thing as a "stop bit". Use the proper naming: "stop
condition".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In smbus-protocol.rst we use the text "Implemented by" for the same meaning
as "This corresponds to". Change everything to "Implemented by" for
coherency.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Some of the section names are not very clear. Reading those names in the
index.rst page does not help much in grasping what the content is supposed
to be.

Rename those sections to clarify their content, especially when reading
the index page.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use a monospace (literal) formatting for better readability of sysfs
attributes and the "dummy" client name. This looks much more readable in
ReST-generated output.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This section applies only to code for very old kernels. Avoid people
reading this unnecessarily.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use ReST syntax so that a proper hyperlink is generated.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use a monospace (literal) formatting for better readability of sysfs
attributes.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Among the "static" instantiation methods the "board file" method is
described first. Move it as last, since it is being replaced by the other
methods.

Also fix subsubsection heading syntax and remove the "Method 1[abc]"
prefix as the subsubsection structure clarifies the logical hierarchy.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use ReST syntax so that a proper hyperlink is generated.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Clarify from the beginning what these transactions are, and specifically
how they differ from the SMBus counterparts, i.e. the lack of a Count byte.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Remove misplaced dot before colon.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The subject is plural, fix the verb.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This clarifies these are functions (and would/will adds a hyperlink to the
function documentation if/when documented).
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Hyperlinks from function names are not generated in headings. Move them in
the plain text so they are rendered as clickable hyperlinks.

While there also remove an unneeded colon in a heading.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use the proper ACK and NACK naming from the I2C specification instead of
"accept" and "reverse accept".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

These colons are not needed: the columns already nicely separate the
symbols from their description. They are also inconsistently preceded by
whitespace.

Remove the colons completely to simplify and clean up.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In I2C there is no such thing as a "start bit" or a "stop bit". Use the
proper naming: "start condition" and "stop condition".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use the proper ReST syntax to generate a valid hyperlink.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use the proper ACK and NACK naming from the I2C specification instead of
"accept" and "reverse accept".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

These colons are not needed: the columns already nicely separate the
symbols from their description. They are also inconsistently preceded by
whitespace.

Remove the colons completely to simplify and clean up.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In I2C there is no such thing as a "start bit" or a "stop bit". Use the
proper naming: "start condition" and "stop condition".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This clarifies these are functions and adds a hyperlink to the function
documentation.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

"I2C transfer" is a legitimate english sentence, no need for a hyphen
between the two words, as as such it is used in most of the
documentation. Remove the hyphen in the few places where it is present.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Fix "issus" -> "issues".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Uppercase "I2C" is used almost everywhere in the docs, but the lowercase
version "i2c" is used somewhere. Use the uppercase form consistently.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This section, partly dating back to the pre-git era, is somewhat
unclear and partly incorrect. Rewrite it almost completely including a
reference figure, concise but precise definition of each term and the
paths where drivers are found. Particular care has been put in clarifying
the relation between adapter and algorithm, which has no correspondence
in the I2C spec terminology.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

- state the "official" name (I²C, not I2C, according to the spec) at
   the beginning but keep using the more practical I2C elsewhere
 - mention some known different names
 - add link to the specification document
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The index page currently lists sections in alphabetical file order without
caring about their content. Sort sections based on their content logically,
according to the following structure:

 * Intro to I2C/SMBus and their usage in Linux: summary, i2c-protocol,
   smbus-protocol, instantiating-devices, busses/index, i2c-topology,
   muxes/i2c-mux-gpio
 * Implementing drivers: writing-clients, dev-interface,
   dma-considerations, fault-codes, functionality
 * Debugging: gpio-fault-injection, i2c-stub
 * Slave I2C: slave-interface, slave-eeprom-backend
 * Advanced: ten-bit-addresses
 * Obsolete info: upgrading-clients, old-module-parameters
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The main feature is the idle-state rework of the pca954x driver from Biwen Li.

Merge tag 'at24-updates-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.6

at24 updates for linux v5.6

- minor maintenance: update the license tag, sort headers
- move support for the write-protect pin into nvmem core
- add a reference to the new wp-gpios property in nvmem to at25 bindings
- add support for regulator and pm_runtime control

There is a statement that is indented one level too deeply, remove
the extraneous tab.

Fixes: b4c119db ("i2c: xiic: Add timeout to the rx fifo wait loop")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

There is a spelling mistake in a module parameter description.
Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Although in the most platforms, the power of eeprom are alway
on, some platforms disable the eeprom power in order to meet
low power request. This patch add the pm_runtime ops to control
power to support all platforms.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
[Bartosz: rebased on top of current at24/for-next]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

In some platforms, they disable the power-supply of eeprom due
to power consumption reduction. This patch add vcc-supply property.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Update the help text to reflect current support devices:
1. The Exynos high speed I2C driver supports Exynos5 (ARMv7), Exynos5433
   and Exynos7 (both ARMv8) SoCs,
2. The S3C I2C driver supports S3C, S5Pv210 and Exynos{3,4,5} SoCs.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>