- 04 Sep, 2008 1 commit
-
-
Hans de Goede authored
- Add documentation for some known registers - Add support for vga modes (320x240, 160x120) for sif sensors - Remove F_RAW sensor flag raw mode should work on any sensor as its a bridge only thing and keeping the flag was becoming awkward. - Fixup ov6650 and pas106 auto exposure window settings Signed-off-by:
Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by:
Jean-Francois Moine <moinejf@free.fr> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 03 Sep, 2008 39 commits
-
-
Adrian Bunk authored
This patch fixes a memory leak in an error path. Reported-by:
Adrian Bunk <bunk@kernel.org> Signed-off-by:
-
Adrian Bunk authored
This patch fixes a memory leak ("fw" wasn't freed). Reported-by: -
Adrian Bunk authored
video_device_release() does kfree(), which made the following printk() doing a use-after-free. printk() first and release then. Reported-by:
-
Michael Krufky authored
This adds basic support for the Hauppauge Nova-TD-500 84xxx series. A future patch will allow for one aerial input to supply both tuners. With the current code, an aerial must be plugged into each antannae input in order for both tuners to function. Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Michael Krufky authored
This comment helps to make the code more readable. Signed-off-by:
-
Jean Delvare authored
Some DVB drivers are incorrectly assuming that the size of i2c_adapter.name is I2C_NAME_SIZE. Here's a fix. Also change strncpy to strlcpy, as the former is error-prone (and was indeed incorrectly used.) Signed-off-by:
Jean Delvare <khali@linux-fr.org> Acked-by:
Uwe Bugla <uwe.bugla@gmx.de> Reviewed-by:
Steven Toth <stoth@hauppauge.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Hans de Goede authored
1) Lower the hstart setting for all sensor by 1 so that we generate (compressed) BGGR data just like sn9c102 does (instead of GBRG data) 2) Add support for raw bayer output in the lowest resolutions (not enough bandwidth for higher resolutions), this should work with all sensors but to be sure only enable it for sensors where it has been tested. Signed-off-by:
-
Hans de Goede authored
Under certain conditions sonixb compressed frame size can get bigger then the uncompressed size (seen with 0c45:6028), so make the buffers slightly bigger. Signed-off-by:
-
Hans de Goede authored
-the usb-id table caried several flags which were not usb-id specific but sensor specific, add a sensor_data array and move these flag there -fr_h_sz was being abused to store and check which bridge was being used instead add a bridge member to the sd struct -now that we have a sensor_data table use that to store pointers to init_sequences instead of using switch cases on sd->sensor Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Hans de Goede authored
-remove USB-id's from zc0301 for cams for which zc0301.c does not support the sensor -remove USB-id's from sn9c102 for cams where sn9c102 does not support the bridge sensor combination -no longer make inclusion of usb id's removed from zc0301 and sn9c102 conditional in gspca -fix conditional inclusion of USB-id's in gspca to also work when the conflicting drivers are build as a module -add a number of USB-id's to gspca from various windows .inf files: 0c45:608f from generic sonix sn9c103 inf file (+ ov7630 which we support) 041e:4022 from creative webcam nx pro, same as already supported 041e:401e 0ac8:0301 from generic zc0301 driver which supports many sensors 10fd:804d from typhoon webshot driver (also FlyCAM-USB 300 plus) Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Jean-Francois Moine authored
The USB buffer may be used for DMA and there may be a caching problem if the buffer is part of the device structure. Thanks to Alan Stern. Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Hans de Goede authored
-Add usb id for 093a:2624 (pac7302) -Report some controls to userspace with 7302 only, as they are 7302 only -Add gain and exposure controls -Add autogain -Fix 7302 imaged being mirrored by default Signed-off-by:
-
Jean-Francois Moine authored
- the stream must stop when the main application closes the device. Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Jean-Francois Moine authored
- new function 'init' called on probe and resume - remove the functions 'open' and 'closed' - 'stopN' and 'stop0' are optional Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Hans de Goede authored
- turn the led of the cam off after plugging in the cam - move the probe code from open to config, so that if the probe fails we never register Signed-off-by:
-
Hans de Goede authored
- set some controls as disabled instead of copying the device descr. - in the ov6650 / 7650 exposure code clamp reg 11 before (instead of after) using it to calculate reg 10. - disable brightness (instead of ignoring it) for the TAS5110. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
- documentation for some registers - some preparations for adding autogain_n_exposure functionality - various pac7311 fixes - disable brightness and colors controls for 7311 - fix contrast control for 7311 - add hflip and vflip controls for 7311 - minimal jpeg header - proper SOF detection Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Hans de Goede authored
the previous patch (sensor upside down). Signed-off-by:
-
Steven Toth authored
I need this so I can better isolate my linux email from my corporate email. Signed-off-by:
Steven Toth <stoth@linuxtv.org> Signed-off-by:
-
Steven Toth authored
If apps pass QAM_AUTO then we need to obey it. Signed-off-by:
-
Steven Toth authored
If apps pass QAM_AUTO then we need to obey it. Signed-off-by:
-
Hans Verkuil authored
Not a bug as such, but it looks really strange doing this before checking whether the state structure could be allocated. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Andy Walls authored
cx18: Simplify queue flush logic to prevent oops in cx18_flush_queues(). If accounting of a queue is in error, logic borrowed from ivtv will cause an oops when flushing the queues for a stream. This change greatly simplifies the queue flush logic, and sets the queue back to sane defaults on a flush. Signed-off-by:
Andy Walls <awalls@radix.net> Signed-off-by:
-
Hans Verkuil authored
Fixed a lot of sparse warnings: mostly warnings about shadowed variables and signed/unsigned mismatches. Signed-off-by:
-
