- 26 Jan, 2020 17 commits
-
-
John Crispin authored
Add IEEE80211_RADIOTAP_HE_DATA1_BW_RU_ALLOC_KNOWN to the list of known fields. Not doing so will result in wireshark not calculating the bitrate correctly. Signed-off-by:
John Crispin <john@phrozen.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Colin Ian King authored
In the unlikely event that cap->supported_bands has neither WMI_HOST_WLAN_2G_CAP set or WMI_HOST_WLAN_5G_CAP set then pointer band is null and a null dereference occurs when assigning band->n_iftype_data. Move the assignment to the if blocks to avoid this. Cleans up static analysis warnings. Addresses-Coverity: ("Explicit null dereference") Fixes: 9f056ed8 ("ath11k: add HE support") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Bhagavathi Perumal S authored
This adds missing rx rate info stats like pilot evm, per chain rssi, per user ul ppdu and mpdu counts and ul ofdma rate info etc. And add null checks for memory alloc failures. Signed-off-by:
Bhagavathi Perumal S <bperumal@codeaurora.org> Signed-off-by:
-
Colin Ian King authored
Currently the structure ts is not inititalized and ts.flags contains garbage values from the stack. This is being passed into function ath11k_dp_tx_status_parse that bit-wise or'ing in settings into the ts.flags field. To avoid flags (and other fields) from containing garbage, initialize the structure to zero before use. Addresses-Coverity: ("Uninitialized scalar variable)" Fixes: d5c65159 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: -
Bhagavathi Perumal S authored
The channel info parameters are required by the firmware to process TxBf parameters. Currently TxBf is passed prior to the channel info. This patch moves TxBf setup after the channel setup. Signed-off-by:
-
Anilkumar Kolli authored
This patch enables HE tlvs in ppdu stats for pktlog lite mode. Signed-off-by:
Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by:
-
Arnd Bergmann authored
When CONFIG_ATH11K_DEBUGFS is disabled, but CONFIG_MAC80211_DEBUGFS is turned on, the driver fails to build: drivers/net/wireless/ath/ath11k/debugfs_sta.c: In function 'ath11k_dbg_sta_open_htt_peer_stats': drivers/net/wireless/ath/ath11k/debugfs_sta.c:416:4: error: 'struct ath11k' has no member named 'debug' ar->debug.htt_stats.stats_req = stats_req; ^~ It appears that just using the former symbol is sufficient here, adding a Kconfig dependency takes care of the corner cases. Fixes: d5c65159 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Govind Singh authored
For some targets ex: QCS404, SCM permissions for MSA region is statically configured in TrustZone fw. Add SCM call disable option for such targets to avoid duplicate permissions. Testing: Tested on WCN3990 HW Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1 Signed-off-by:
Govind Singh <govinds@codeaurora.org> Signed-off-by:
-
Govind Singh authored
Add boolean context flag to disable SCM call for statically mapped msa region. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Zhi Chen authored
This reverts commit 76d164f5. PCIe hung issue was observed on multiple platforms. The issue was reproduced when DUT was configured as AP and associated with 50+ STAs. For QCA9984/QCA9888, the DMA_BURST_SIZE register controls the AXI burst size of the RD/WR access to the HOST MEM. 0 - No split , RAW read/write transfer size from MAC is put out on bus as burst length 1 - Split at 256 byte boundary 2,3 - Reserved With PCIe protocol analyzer, we can see DMA Read crossing 4KB boundary when issue happened. It broke PCIe spec and caused PCIe stuck. So revert the default value from 0 to 1. Tested: IPQ8064 + QCA9984 with firmware 10.4-3.10-00047 QCS404 + QCA9984 with firmware 10.4-3.9.0.2--00044 Synaptics AS370 + QCA9888 with firmware 10.4-3.9.0.2--00040 Signed-off-by:
Zhi Chen <zhichen@codeaurora.org> Signed-off-by:
-
Wen Gong authored
When simulate random transfer fail for sdio write and read, it crash sometimes. Test steps: 1. Add config and update kernel: CONFIG_FAIL_MMC_REQUEST=y CONFIG_FAULT_INJECTION=y CONFIG_FAULT_INJECTION_DEBUG_FS=y 2. run simulate fail: cd /sys/kernel/debug/mmc1/fail_mmc_request echo 10 > probability echo 10 > times # repeat until hitting issues 3. it crash, the act len of ath10k_htc_hdr is higher than allocate len, it cause panic: [ 99.723482] skbuff: skb_over_panic: text:00000000caa0f780 len:57013 put:57013 head:000000004116f24a data:0000000019ecb4dc tail:0xdef5 end:0x640 dev:<NULL> [ 99.737697] ------------[ cut here ]------------ [ 99.742327] kernel BUG at /mnt/host/source/src/third_party/kernel/v4.19/net/core/skbuff.c:104! [ 99.750937] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [ 99.831154] Process kworker/0:2 (pid: 151, stack limit = 0x00000000728010bf) [ 99.838200] CPU: 0 PID: 151 Comm: kworker/0:2 Tainted: G W 4.19.85 #48 [ 99.846022] Hardware name: MediaTek krane sku0 board (DT) [ 99.851429] Workqueue: events sdio_irq_work [ 99.855614] pstate: 60000005 (nZCv daif -PAN -UAO) [ 99.860402] pc : skb_panic+0x64/0x68 [ 99.863974] lr : skb_panic+0x64/0x68 [ 99.867542] sp : ffffff8008833a90 [ 99.870850] x29: ffffff8008833ac0 x28: ffffffe52e337370 [ 99.876159] x27: ffffffe52e328a90 x26: 000000000000e0d0 [ 99.881469] x25: ffffffe52e336b60 x24: 000000000000deb5 [ 99.886779] x23: ffffffe52e340680 x22: ffffffe4efd47e00 [ 99.892088] x21: 000000000000deb5 x20: ffffffa516d85b4c [ 99.897397] x19: ffffffa526928037 x18: 0000000000000000 [ 99.902706] x17: 000000000000003c x16: ffffffa5265b6c80 [ 99.908015] x15: 0000000000000006 x14: 3a76656420303436 [ 99.913325] x13: 0000000000029bf0 x12: 0000000000000000 [ 99.918634] x11: 0000000000000000 x10: 0000000000000000 [ 99.923943] x9 : a3b907e4b2783000 x8 : a3b907e4b2783000 [ 99.929253] x7 : 0000000000000000 x6 : ffffffa526f66d76 [ 99.934563] x5 : 0000000000000000 x4 : 0000000000000000 [ 99.939872] x3 : 000000000002a5ab x2 : ffffffe53feed918 [ 99.945182] x1 : ffffffe53fee4a08 x0 : 000000000000008e [ 99.950491] Call trace: [ 99.952937] skb_panic+0x64/0x68 [ 99.956165] skb_put+0x7c/0x84 [ 99.959224] ath10k_sdio_irq_handler+0x740/0xbb8 [ath10k_sdio] [ 99.965055] process_sdio_pending_irqs+0x58/0x1a4 [ 99.969758] sdio_run_irqs+0x34/0x60 [ 99.973329] sdio_irq_work+0x1c/0x28 [ 99.974930] cros-ec-spi spi2.0: SPI transfer timed out [ 99.976904] process_one_work+0x210/0x410 [ 99.976911] worker_thread+0x234/0x3dc [ 99.976923] kthread+0x120/0x130 [ 99.982090] cros-ec-spi spi2.0: spi transfer failed: -110 [ 99.986054] ret_from_fork+0x10/0x18 [ 99.986063] Code: aa1403e2 2a1503e4 a90023e9 97e37d1a (d4210000) [ 99.986068] ---[ end trace cb6d948c5a0fd6c7 ]--- [ 100.017250] Kernel panic - not syncing: Fatal exception [ 100.018879] cros-ec-spi spi2.0: Command xfer error (err:-110) [ 100.023659] SMP: stopping secondary CPUs [ 100.023703] Kernel Offset: 0x251dc00000 from 0xffffff8008000000 [ 100.023707] CPU features: 0x0,2188200c [ 100.023709] Memory Limit: none The simulate fail of sdio is not a real sdio transter fail, it only set an error status in mmc_should_fail_request after the transfer end, actually the transfer is success, then sdio_io_rw_ext_helper will return error status and stop transfer the left data. For example, the really RX len is 286 bytes, then it will split to 2 blocks in sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the first 256 bytes get an error status by mmc_should_fail_request,then the left 30 bytes will not read in this RX operation. Then when the next RX arrive, the left 30 bytes will be considered as the header of the read, the top 8 bytes will be considered as ath10k_htc_hdr, but actually the 8 bytes is not the ath10k_htc_hdr, so the act_len from this ath10k_htc_hdr is not correct, if it is a big value, such as 57013, it will trigger skb_panic. Drop the skb with invalid length will be reasonable. This patch only effect sdio chips. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029. Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
-
zhengbin authored
Fixes coccicheck warning: drivers/net/wireless/ath/ath10k/htt_rx.c:2143:2-31: WARNING: Assignment of 0/1 to bool variable Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
zhengbin <zhengbin13@huawei.com> Signed-off-by:
-
Bjorn Andersson authored
The WiFi firmware found on sm8150 requires that the QDSS clock is ticking in order to operate, so add an optional clock to the binding to allow this to be specified in the sm8150 dts and add the clock to the list of clocks in the driver. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by:
-
Bryan O'Donoghue authored
The description of ath10k_pci_dump_memory_sram() is inaccurate, an error can never be returned, it is always the length. Update the comment to reflect. Fixes: 219cc084 ("ath10k: add memory dump support QCA9984") Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
-
Bryan O'Donoghue authored
ath10k_pci_dump_memory_reg() will try to access memory of type ATH10K_MEM_REGION_TYPE_IOREG however, if a hardware restart is in progress this can crash a system. Individual ioread32() time has been observed to jump from 15-20 ticks to > 80k ticks followed by a secure-watchdog bite and a system reset. Work around this corner case by only issuing the read transaction when the driver state is ATH10K_STATE_ON. Tested-on: QCA9988 PCI 10.4-3.9.0.2-00044 Fixes: 219cc084 ("ath10k: add memory dump support QCA9984") Signed-off-by:
-
zhengbin authored
Fixes coccicheck warning: drivers/net/wireless/ath/wil6210/main.c:765:1-14: WARNING: Assignment of 0/1 to bool variable drivers/net/wireless/ath/wil6210/txrx.c:1143:1-19: WARNING: Assignment of 0/1 to bool variable drivers/net/wireless/ath/wil6210/wmi.c:1516:4-23: WARNING: Assignment of 0/1 to bool variable drivers/net/wireless/ath/wil6210/wmi.c:1523:4-23: WARNING: Assignment of 0/1 to bool variable drivers/net/wireless/ath/wil6210/wmi.c:1538:4-30: WARNING: Assignment of 0/1 to bool variable drivers/net/wireless/ath/wil6210/wmi.c:1545:4-30: WARNING: Assignment of 0/1 to bool variable Reported-by:
-
zhengbin authored
Fixes coccicheck warning: drivers/net/wireless/ath/ath9k/ar9003_aic.c:409:2-12: WARNING: Assignment of 0/1 to bool variable Reported-by:
-
- 13 Jan, 2020 2 commits
-
-
Geert Uytterhoeven authored
Use the print_hex_dump_debug() helper, instead of open-coding the same operations. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Geert Uytterhoeven authored
Remove unused fields, copied from the Sun LANCE driver eons ago. Signed-off-by:
-
- 12 Jan, 2020 11 commits
-
-
Jakub Kicinski authored
Linus Walleij says: ==================== IXP4xx networking cleanups This is a patch series which jams together Arnds and mine cleanups for the IXP4xx networking. I also have patches for device tree support but that requires more elaborate work, this series is some of mine and some of Arnds patches that is a good foundation for his multiplatform work and my device tree work. These are for application to the networking tree so that can be taken in one separate sweep. I have tested the patches for a bit using zeroday builds and some boots on misc IXP4xx devices and haven't run into any major problems. We might find some new stuff as a result from the new compiler coverage. I had to depromote enabling compiler coverage at one point in the v2 set because it depended on other patches making the code more generic. The change in v3 was simply dropping one offending patch hardcoding base addresses into the driver. The change in v4 drops a stable@ tag that was unnecessary. This v5 is a rebase of the v4 patch set on top of net-next. ==================== Signed-off-by: -
Linus Walleij authored
Use the netdevice struct device .parent field when calling dma_pool_create(): the .dma_coherent_mask and .dma_mask pertains to the bus device on the hardware (platform) bus in this case, not the struct device inside the network device. This makes the pool allocation work. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
In order to probe this ethernet interface from the device tree all physical MMIO regions must be passed as resources. Begin this rewrite by first passing the port base address as a resource for all platforms using this driver, remap it in the driver and avoid using any reference of the statically mapped virtual address in the driver. Signed-off-by:
-
Linus Walleij authored
Simplify and correct a bunch of messages using printk directly to use the netdev_* macros. I have not changed all of them, just the low-hanging fruit. Signed-off-by:
-
Linus Walleij authored
Use "ndev" for the struct net_device and "dev" for the struct device in probe() and remove(). Add the local "dev" pointer for later use in refactoring. Take this opportunity to fix inverse christmas tree coding style. Signed-off-by:
-
Linus Walleij authored
The IXP4xx driver was initializing the MDIO bus before even probing, in the callbacks supposed to be used for setting up the module itself, and with the side effect of trying to register the MDIO bus as soon as this module was loaded or compiled into the kernel whether the device was discovered or not. This does not work with multiplatform environments. To get rid of this: set up the MDIO bus from the probe() callback and remove it in the remove() callback. Rename the probe() and remove() calls to reflect the most common conventions. Since there is a bit of checking for the ethernet feature to be present in the MDIO registering function, making the whole module not even be registered if we can't find an MDIO bus, we need something similar: register the MDIO bus when the corresponding ethernet is probed, and return -EPROBE_DEFER on the other interfaces until this happens. If no MDIO bus is present on any of the registered interfaces we will eventually bail out. None of the platforms I've seen has e.g. MDIO on EthB and only uses EthC, there is always a Ethernet hardware on the NPE (B, C) that has the MDIO bus, we just might have to wait for it. Signed-off-by:
-
Arnd Bergmann authored
The platform data is needed to compile the driver as standalone, so move it to a global location along with similar files. Signed-off-by:
-
Arnd Bergmann authored
The ixp46x ptp driver has a somewhat unusual setup, where the ptp driver and the ethernet driver are in different directories but access the same registers that are defined a platform specific header file. Moving everything into drivers/net/ makes it look more like most other ptp drivers and allows compile-testing this driver on other targets. Signed-off-by:
-
Arnd Bergmann authored
The ixp4xx_hss driver needs the platform data definition and the system clock rate to be compiled. Move both into a new platform_data header file. This is a prerequisite for compile testing, but turning on compile testing requires further patches to isolate the SoC headers. Signed-off-by:
-
Arnd Bergmann authored
Change the driver to use portable integer types to avoid warnings during compile testing: drivers/net/wan/ixp4xx_hss.c:863:21: error: cast to 'u32 *' (aka 'unsigned int *') from smaller integer type 'int' [-Werror,-Wint-to-pointer-cast] memcpy_swab32(mem, (u32 *)((int)skb->data & ~3), bytes / 4); ^ drivers/net/wan/ixp4xx_hss.c:979:12: error: incompatible pointer types passing 'u32 *' (aka 'unsigned int *') to parameter of type 'dma_addr_t *' (aka 'unsigned long long *') [-Werror,-Wincompatible-pointer-types] &port->desc_tab_phys))) ^~~~~~~~~~~~~~~~~~~~ include/linux/dmapool.h:27:20: note: passing argument to parameter 'handle' here dma_addr_t *handle); ^ Signed-off-by: -
Jonathan Lemon authored
On modern hardware with a large number of cpus and using XDP, the current MSIX limit is insufficient. Bump the limit in order to allow more queues. Signed-off-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Reviewed-by:
Jack Wang <jinpu.wang@cloud.ionos.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
- 11 Jan, 2020 10 commits
-
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: add some misc update about reset issue This series includes some misc update relating to reset issue. [patch 1/7] & [patch 2/7] splits hclge_reset()/hclgevf_reset() into two parts: preparing and rebuilding. Since the procedure of FLR should be separated out from the reset task([patch 3/7 & patch 3/7]), then the FLR's processing can reuse these codes. pci_error_handlers.reset_prepare() is void type function, so [patch 6/7] & [patch 7/7] factor some codes related to PF function reset to make the preparing done before .reset_prepare() return. BTW, [patch 5/7] enlarges the waiting time of reset for matching the hardware's. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Huazhong Tan authored
hclge_reset_prepare_down() is only used to inform VF that PF is going to do function reset, then using hclge_func_reset_sync_vf() in hclge_reset_prepare_wait() to query whether VF is ready before asserting PF function reset. To make the code more readable, this patch uses a new function hclge_function_reset_notify_vf() to do this job. Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Huazhong Tan authored
When synchronizes with VFs fail before PF function reset, PF driver should go on its function reset, otherwise it can not run normally anymore. So, hclge_func_reset_sync_vf() should not affect the processing of PF reset, this patch modifies its return type to void. Signed-off-by:
-
Huazhong Tan authored
When the load of firmware is high, its reset task may takes more time(which will be as long as 35 seconds). So this patch modifies HCLGE_RESET_WAIT_CNT to match the firmware's. Signed-off-by:
-
Huazhong Tan authored
Currently, the actual work of VF FLR is handled in the reset task, which is asynchronous. So in some case, if the preparing and rebuilding are not done, then the VF FLR will trigger some problems, for example, makes hardware go into chaos. So this patch separates the process of VF FLR from reset task, and adds a semaphore to serialize this reset and others. When FLR's preparing fails, if there has other higher level reset pending or failing times less than the HCLGE_FLR_RETRY_CNT, this preparing should be retried, otherwise it will get into a wrong state. BTW, while the hardware reports misc interrupt during pcie_flr(), the driver can not receive this interrupt anymore, so disable it when hclgevf_flr_prepare() return, and re-enable it when enter hclgevf_flr_done(). Avoid declaring internal function hclgevf_enable_vector(), this patch also moves its definition forward, and removes unused enum hnae3_flr_state. Signed-off-by:
-
Huazhong Tan authored
Currently, the actual work of PF FLR is handled in the reset task, which is asynchronous. So in some case, if the preparing and rebuilding are not done, then the PF FLR will trigger some problems, for example, makes hardware go into chaos. So this patch separates the process of PF FLR from reset task, and adds a semaphore to serialize this reset and others. When FLR's preparing fails, if there has other higher level reset pending or failing times less than the HCLGE_FLR_RETRY_CNT, this preparing should be retried, otherwise PF and its VF may get into wrong state. BTW, while the hardware reports misc interrupt during pcie_flr(), the driver can not receive this interrupt anymore, so disable it when hclge_flr_prepare() return, and re-enable it when enter hclge_flr_done(). Signed-off-by:
-
Huazhong Tan authored
hclgevf_reset() is a little bloated, and the process of VF FLR will be separated from the reset task later. So this patch splits hclgevf_reset() into hclgevf_reset_prepare() and hclge_reset_rebuild(), then FLR can also reuse these two functions. Also moves HNAE3_UP_CLIENT into hclgevf_reset_stack(). Signed-off-by:
-
Huazhong Tan authored
hclge_reset() is a little bloated, and the process of PF FLR will be separated from the reset task later. So this patch splits hclge_reset() into hclge_reset_prepare() and hclge_reset_rebuild(), then FLR can also reuse these two functions. BTW, since hclge_clear_reset_cause() and hclge_reset_prepare_up() will not affect the device, so in hclge_reset_rebuild(), these functions are called without rtnl_lock. Signed-off-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/sfc/mcdi_functions.c: In function 'efx_mcdi_ev_init': drivers/net/ethernet/sfc/mcdi_functions.c:79:28: warning: variable 'nic_data' set but not used [-Wunused-but-set-variable] commit 4438b587 ("sfc: move MCDI event queue management code") introduces this unused variable. Reported-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
YueHaibing authored
Remove duplicated include. Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
