Simplify stm32h7_spi_prepare_fthlv() function implementation,
no functional change intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alain Volmat <alain.volmat@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Antonio Borneo <antonio.borneo@st.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Roman Guskov <rguskov@dh-electronics.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/20210104123114.261596-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

We don't need to force this to be trigger high here, as the firmware
properly configures the irq flags already. Drop it to save a line.

Cc: Douglas Anderson <dianders@chromium.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210112001301.687628-1-swboyd@chromium.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Currently we use concrete version to determine the max_cmd_dword.
New entries should be added for compatible hardwares of new version
or on new platform, otherwise the device will use 16 dwords instead
of 64 even if it supports, which will degrade the performance.
This will decrease the compatibility and the maintainability.

Drop the switch-case statement of the version checking. Only version
less than 0x351 supports maximum 16 command dwords.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1610526716-14882-1-git-send-email-yangyicong@hisilicon.comSigned-off-by: Mark Brown <broonie@kernel.org>

With CONFIG_PM_SLEEP disabled the rpcif_spi_pm_ops variable is still
referenced and thus increasing the size of kernel.

Fix this issue by adding CONFIG_PM_SLEEP #ifdef check around the .pm
assignment (image size is critical on RZ/A SoC's where the SRAM sizes
range 4~5 MiB).

Fixes: 9584fc95 ("spi: rpc-if: Remove CONFIG_PM_SLEEP ifdefery")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210107145329.27966-1-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

The kernel test robot reports the following warning.

drivers/spi/spi-cadence-quadspi.c:966:24: warning: comparison of distinct pointer types ('typeof (len) *' (aka 'unsigned int *') and 'typeof (500UL) *' (aka 'unsigned long *')) [-Wcompare-distinct-pointer-types]
                                            msecs_to_jiffies(max(len, 500UL)))) {
                                                             ^~~~~~~~~~~~~~~
   include/linux/minmax.h:58:19: note: expanded from macro 'max'
   #define max(x, y)       __careful_cmp(x, y, >)
                           ^~~~~~~~~~~~~~~~~~~~~~
   include/linux/minmax.h:42:24: note: expanded from macro '__careful_cmp'
           __builtin_choose_expr(__safe_cmp(x, y), \
                                 ^~~~~~~~~~~~~~~~
   include/linux/minmax.h:32:4: note: expanded from macro '__safe_cmp'
                   (__typecheck(x, y) && __no_side_effects(x, y))
                    ^~~~~~~~~~~~~~~~~
   include/linux/minmax.h:18:28: note: expanded from macro '__typecheck'
           (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
                      ~~~~~~~~~~~~~~ ^  ~~~~~~~~~~~~~~
   1 warning generated.

This happens because size_t is unsigned long on 64-bit platforms like
arm64 but it is unsigned int on 32-bit platforms like arm. Omitting the
"UL" would result in a warning on 64-bit platforms. Squash it by type
casting the arguments to size_t using max_t(). This way builds on both
type of platforms can be satisfied. There is no chance of any truncation
since 500 is small enough to fit into both int and long.

Fixes: f453f293 ("spi: cadence-quadspi: Wait at least 500 ms for direct reads")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210108181457.30291-1-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fix the following coccicheck warning:
./drivers/spi/spi-bcm-qspi.c:884:5-34: WARNING: Comparison to bool
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Reported-by: Abaci Robot<abaci@linux.alibaba.com>
Link: https://lore.kernel.org/r/1610357189-60031-1-git-send-email-abaci-bugfix@linux.alibaba.comSigned-off-by: Mark Brown <broonie@kernel.org>

Document R-Car V3U (R8A779A0) SoC bindings.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210108103522.2025880-1-geert+renesas@glider.beSigned-off-by: Mark Brown <broonie@kernel.org>

Fix a new warning report by build for make ARCH=MIPS allmodconfig:

drivers/spi/spi-cadence-quadspi.c: In function 'cqspi_direct_read_execute':
 ./include/linux/minmax.h:18:28: warning: comparison of distinct pointer types lacks a cast
    18 |  (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
       |                            ^~
 ./include/linux/minmax.h:32:4: note: in expansion of macro '__typecheck'
    32 |   (__typecheck(x, y) && __no_side_effects(x, y))
       |    ^~~~~~~~~~~
 ./include/linux/minmax.h:42:24: note: in expansion of macro '__safe_cmp'
    42 |  __builtin_choose_expr(__safe_cmp(x, y), \
       |                        ^~~~~~~~~~
 ./include/linux/minmax.h:58:19: note: in expansion of macro '__careful_cmp'
    58 | #define max(x, y) __careful_cmp(x, y, >)
       |                   ^~~~~~~~~~~~~
 drivers/spi/spi-cadence-quadspi.c:1153:24: note: in expansion of macro 'max'
  1153 |       msecs_to_jiffies(max(len, 500UL)))) {
       |                        ^~~

"len" is unsigned,however,"500" is unsigned long.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Link: https://lore.kernel.org/r/20210107115704.3835282-1-siyanteng@loongson.cnSigned-off-by: Mark Brown <broonie@kernel.org>

This series adds Tegra210, Tegra186, and Tegra194 Quad SPI driver and
enables Quad SPI on Jetson Nano and Jetson Xavier NX.

QSPI controller is available on Tegra210, Tegra186 and Tegra194.

Tegra186 and Tegra194 has additional feature of combined sequence mode
where command, address and data can all be transferred in a single transfer.
Combined sequence mode is useful only when using DMA mode transfer.

This series does not have combined sequence mode feature as Tegra186/Tegra194
GPCDMA driver is not upstreamed yet.

This series includes
- dt-binding document
- QSPI driver for Tegra210/Tegra186/Tegra194
- Enables QSPI on Jetson Nano and Jetson Xavier NX.

Delta between patch versions:
[v5]:	Simplified implementation in Patch-0006

[v4]:	Updated dummy cycles implementation based on v3 feedback
	- Added dummy_data bit field int spi_transfer to indicate corresponding
	  transfer is dummy bytes transfer.
	- Updated Tegra QSPI transfer_one_message to identify dummy transfer and
	  to use HW supported dummy bytes transfer when dummy cycles are with in
	  Tegra QSPI supported max HW dummy cycles otherwise fallsback to transfer
	  dummy bytes from software.
	- Updated dt-bindings based on v3 feedback.

[v3]:	v2 has some mixed patches sent out accidentally.
	v3 sends proper patches with fixes mentioned in v2.

[v2]:	below v1 feedback
	- Added SPI_MASTER_USES_HW_DUMMY_CYCLES flag for controllers supporting
	  hardware dummy cycles and skips dummy bytes transfer from software for
	  these controllers.
	- Updated dt-binding doc with tx/rx tap delay properties.
	- Added qspi_out clock to dt-binding doc which will be used later with
	  ddr mode support.
	- All other v1 feedback on some cleanup.

Sowjanya Komatineni (9):
  dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM
  dt-bindings: spi: Add Tegra Quad SPI device tree binding
  MAINTAINERS: Add Tegra Quad SPI driver section
  spi: tegra210-quad: Add support for Tegra210 QSPI controller
  spi: spi-mem: Mark dummy transfers by setting dummy_data bit
  spi: tegra210-quad: Add support for hardware dummy cycles transfer
  arm64: tegra: Enable QSPI on Jetson Nano
  arm64: tegra: Add QSPI nodes on Tegra194
  arm64: tegra: Enable QSPI on Jetson Xavier NX

 .../bindings/spi/nvidia,tegra210-quad.yaml         |  117 ++
 MAINTAINERS                                        |    8 +
 .../dts/nvidia/tegra194-p3509-0000+p3668-0000.dts  |   12 +
 arch/arm64/boot/dts/nvidia/tegra194.dtsi           |   28 +
 arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts |   12 +
 arch/arm64/boot/dts/nvidia/tegra210.dtsi           |    5 +-
 drivers/spi/Kconfig                                |    9 +
 drivers/spi/Makefile                               |    1 +
 drivers/spi/spi-mem.c                              |    1 +
 drivers/spi/spi-tegra210-quad.c                    | 1410 ++++++++++++++++++++
 include/dt-bindings/clock/tegra210-car.h           |    2 +-
 include/linux/spi/spi.h                            |    2 +
 12 files changed, 1604 insertions(+), 3 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml
 create mode 100644 drivers/spi/spi-tegra210-quad.c

--
2.7.4

Tegra Quad SPI controller hardware supports sending dummy bytes based
on programmed dummy clock cycles after the actual transfer bytes.

This patch adds this support of hardware dummy bytes transfer and
skips transfer of dummy bytes from the software.

For dummy cycles more than Tegra Quad SPI hardware maximum dummy
cycles limit, driver transfers dummy bytes from the software.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-7-git-send-email-skomatineni@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch marks dummy transfer by setting dummy_data bit to 1.

Controllers supporting dummy transfer by hardware use this bit field
to skip software transfer of dummy bytes and use hardware dummy bytes
transfer.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-6-git-send-email-skomatineni@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

Tegra SoC has a Quad SPI controller starting from Tegra210.

This patch adds support for Tegra210 QSPI controller.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-5-git-send-email-skomatineni@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add maintainers and mailing list entries to Tegra Quad SPI driver
section.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-4-git-send-email-skomatineni@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch adds YAML based device tree binding document for Tegra
Quad SPI driver.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-3-git-send-email-skomatineni@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

Tegra210 QSPI clock output has divider DIV2_SEL which will be enabled
when using DDR interface mode.

This patch adds clock ID for this to dt-binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-2-git-send-email-skomatineni@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

Double Transfer Rate (DTR) mode transfers data twice per clock cycle.
Add support for parsing DTR ops and set up the registers to allow it.

Most SPI NOR flashes expect 2 byte commands. Parse the 2-byte opcode
from SPI MEM and set it up in the CQSPI_REG_OP_EXT_LOWER register.

Increment the delay needed before issuing indirect writes because larger
delay is needed for DTR mode. With the current delay some writes end up
missing.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-8-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

When performing a direct read via DMA the timeout for completion is set
equal to the read length. This is fine for larger reads. For a small
read like the Read Status Register command, the timeout would be 1 or 2
milliseconds. This is not enough to cover the overhead needed in setting
up DMA.

Make sure the timeout is at least 500 ms to allow DMA ample time to
finish. For reads larger than 500 bytes, the timeout will continue to be
equal to the read length.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20201222184425.7028-7-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

The default SPI MEM supports_op hook rejects DTR ops by default. Add a
simple supports_op hook that very closely imitates the SPI MEM one. It
will be extended in later commits to allow DTR ops.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-6-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

SPI MEM deals with dummy bytes but the controller deals with dummy
cycles. Multiplying bytes by 8 is correct if the dummy phase uses 1S
mode since 1 byte will be sent in 8 cycles. But if the dummy phase uses
4S mode then 1 byte will be sent in 2 cycles.

To correctly translate dummy bytes to dummy cycles, the dummy buswidth
also needs to be taken into account. Divide 8 by the buswidth to get the
correct multiplier for getting the number of cycles.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-5-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

If a command does not have an address phase it goes via the STIG path.
The dummy cycles are not initialized for the STIG commands. As a result,
STIG commands with dummy cycles will not work.

Initialize the dummy cycle field before issuing the STIG command to make
sure it is sent correctly. Move the code to calculate dummy cycle value
to a separate function so it is not repeated twice. DTR support will add
some more logic here to it is worth it to extract it out in a function.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-4-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

The controller can only support up to 31 dummy cycles. If the command
requires more it falls back to using 31. This command is likely to fail
because the correct number of cycles are not waited upon. Rather than
silently issuing an incorrect command, fail loudly so the caller can get
a chance to find out the command can't be supported by the controller.

Fixes: 14062341 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-3-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

As of commit 9326e4f1 ("spi: Limit the spi device max speed to
controller's max speed"), the SPI device max speed is set to the
controller's max speed if it is larger. The Cadence QSPI controller does
not set the controller's max speed so it is left at its initial value of
0. This means the SPI device max speed is always set to 0.

The SPI device max speed is used to calculate the baud rate divider when
performing an operation. If this speed is 0, the default divider of 32
is used. No matter what speed is specified by the device tree property
'spi-max-frequency', the device will always operate at ref_clk / 32.

Fix this by setting master->max_speed_hz to the ref clock speed so the
correct divider can be calculated.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-2-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

CPU support for TX49xx is getting removed, so remove support SPI driver
for it.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20210105140305.141401-5-tsbogend@alpha.franken.deSigned-off-by: Mark Brown <broonie@kernel.org>

With the introduction of the 'include/uapi/linux/spi/spi.h' header, the
type of the macros are enforced to 'unsigned long int' via the _BITUL()
macro.

This causes some -Wformat warnings in the spi-stm32 driver.
This patch adds a double-negation operator to the bit-masks. Essentially,
the important values for debugging are 0 or 1, while masking them directly
would show 0 or BIT(x) values.
This way, the type of the arguments are automatically re-cast.

Fixes: f7005142 ("spi: uapi: unify SPI modes into a single spi.h header")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210104143103.56510-1-alexandru.ardelean@analog.comSigned-off-by: Mark Brown <broonie@kernel.org>

The SPI driver for the Renesas RPC-IF is present on the RZ/G2
Series.  Add that to the description.
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210102115412.3402059-3-aford173@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use __maybe_unused for the suspend()/resume() hooks and get rid of
the CONFIG_PM_SLEEP ifdefery to improve the code.
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Pavel Machek <pavel@denx.de>
Link: https://lore.kernel.org/r/20201230145708.28544-3-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Following a change to the SPI framework, providing a value of zero for
'spi-rx-bus-width' and 'spi-tx-bus-width' is now possible and will
essentially mean that no RX or TX is allowed.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-3-alexandru.ardelean@analog.comSigned-off-by: Mark Brown <broonie@kernel.org>

Transmit/receive only is a valid SPI mode. For example, the MOSI/TX line
might be missing from an ADC while for a DAC the MISO/RX line may be
optional. This patch adds these two new modes: SPI_NO_TX and
SPI_NO_RX. This way, the drivers will be able to identify if any of
these two lines is missing and to adjust the transfers accordingly.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-2-alexandru.ardelean@analog.comSigned-off-by: Mark Brown <broonie@kernel.org>

This change moves all the SPI mode bits into a separate 'spi.h' header in
uAPI. This is meant to re-use these definitions inside the kernel as well
as export them to userspace (via uAPI).

The SPI mode definitions have usually been duplicated between between
'include/linux/spi/spi.h' and 'include/uapi/linux/spi/spidev.h', so
whenever adding a new entry, this would need to be put in both headers.

They've been moved from 'include/linux/spi/spi.h', since that seems a bit
more complete; the bits have descriptions and there is the SPI_MODE_X_MASK.

This change also does a conversion of these bitfields to _BITUL() macro.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-1-alexandru.ardelean@analog.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some SPI devices, require toggling the CS every transferred byte.
Enable such possibility in the spi-orion driver.

Note that in order to use it, in the driver of a secondary device
attached to this controller, the SPI bus 'mode' field must be
updated with SPI_CS_WORD flag before calling spi_setup() routine.

In addition to that include a work-around - some devices, such as
certain models of SLIC (Subscriber Line Interface Card),
may require extra delay after CS toggling, so add a minimal
timing relaxation in relevant places.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20201223103827.29721-3-kostap@marvell.comSigned-off-by: Mark Brown <broonie@kernel.org>

The spi-orion driver disables its clocks whenever it is not used.
In usual case during boot (i.e. using SPI flash) it is not a problem,
as the child device driver is present and probed along with
spi_register_master() execution.

However in case the child device driver is not ready
(e.g. when its type is module_spi_driver) the spi_setup() callback
can be called after the spi-orion probe. It may happen,
that as a result there will be an attempt to access controller's
registers with the clocks disabled.

Prevent such situations and make sure the clocks are on,
each time the spi_setup() is called.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20201223103827.29721-2-kostap@marvell.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since commit 36e2c742 ("fs: don't allow splice read/write without
explicit ops") we've required that file operation structures explicitly
enable splice support, rather than falling back to the default handlers.

Most /proc files use the indirect 'struct proc_ops' to describe their
file operations, and were fixed up to support splice earlier in commits
40be821d..b24c30c6, but the mountinfo files interact with the
VFS directly using their own 'struct file_operations' and got missed as
a result.

This adds the necessary support for splice to work for /proc/*/mountinfo
and friends.
Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NTB fixes from Jon Mason:
 "Bug fix for IDT NTB and Intel NTB LTR management support"

* tag 'ntb-5.11' of git://github.com/jonmason/ntb:
  ntb: intel: add Intel NTB LTR vendor support for gen4 NTB
  ntb: idt: fix error check in ntb_hw_idt.c

Pull crypto fixes from Herbert Xu:
 "Fix a number of autobuild failures due to missing Kconfig
  dependencies"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: qat - add CRYPTO_AES to Kconfig dependencies
  crypto: keembay - Add dependency on HAS_IOMEM
  crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY

Pull objtool fix from Ingo Molnar:
 "Fix a segfault that occurs when built with Clang"

* tag 'objtool-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix seg fault with Clang non-section symbols

Pull locking fixes from Ingo Molnar:
 "Misc fixes/updates:

   - Fix static keys usage in module __init sections

   - Add separate MAINTAINERS entry for static branches/calls

   - Fix lockdep splat with CONFIG_PREEMPTIRQ_EVENTS=y tracing"

* tag 'locking-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  softirq: Avoid bad tracing / lockdep interaction
  jump_label/static_call: Add MAINTAINERS
  jump_label: Fix usage in module __init

Pull timer fixes from Ingo Molnar:
 "Update/fix two CPU sanity checks in the hotplug and the boot code, and
  fix a typo in the Kconfig help text.

  [ Context: the first two commits are the result of an ongoing
    annotation+review work of (intentional) tick_do_timer_cpu() data
    races reported by KCSAN, but the annotations aren't fully cooked
    yet ]"

* tag 'timers-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix spelling mistake in Kconfig "fullfill" -> "fulfill"
  tick/sched: Remove bogus boot "safety" check
  tick: Remove pointless cpu valid check in hotplug code

Pull scheduler fix from Ingo Molnar:
 "Fix a context switch performance regression"

* tag 'sched-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Optimize finish_lock_switch()