It is preferred to use syscon per bindind doc
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is better use syscon for IOMUXC GPR, since it contains various
bits for system control
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The IOMUX Controller General purpose register group are unique almost
per SoC, i.MX8MM is not compatible with i.MX6Q. So correct it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The IOMUX Controller General purpose register group are unique almost
per SoC, i.MX8MQ is not compatible with i.MX6Q. So correct it.
Also update name with syscon.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the correct compatible 'nxp,se97b' as it is an SE97BTP chip.
While at it, fix the node name according to device tree spec
recommendations. The EEPROM is a separate node anyway.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add DT nodes for the Hantro VPU found in i.MX8MP SoC.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is an SPBA bus on AIPS3 which includes ecspi1-3,
UART1-3, and Flexcan1-2 according to the TRM.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Drop "interrupt-names" property, since it is broken. The drivers/dma/mxs-dma.c
in Linux kernel does not use it, the property contains duplicate array entries
in existing DTs, and even malformed entries (gmpi, should have been gpmi). Get
rid of that optional property altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Drop "interrupt-names" property, since it is broken. The drivers/dma/mxs-dma.c
in Linux kernel does not use it, the property contains duplicate array entries
in existing DTs, and even malformed entries (gmpi, should have been gpmi). Get
rid of that optional property altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update the board compatible string such that it matches the YAML DT
schema for validation, add the "toradex,verdin-imx8mm-nonwifi" entry.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The HSIO blk-ctrl exposes the high performance PLL as
a simple clock.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Lukas F. Hartmann <lukas@mntre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The only difference in PCIe clock configuration between boards is how
the PCIe reference clock is generated. The refclock configuration is
fully contained in the PCIe PHY node, so the PCIe controller clocks
can be set up in the SoC dtsi, as there is no reason for any board to
use a different configuration.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The hibernation mode of AR8031 PHY defaults to be enabled after hardware
reset. When the cable is unplugged, the PHY will enter hibernation mode
after about 10 senconds and the PHY clocks will be stopped to save
power. However, due to the design of EQOS, the mac needs the RX_CLK of
PHY for software reset to complete. Otherwise the software reset of EQOS
will be failed and do not work correctly. The only way is to disable
hibernation mode of AR8031 PHY for EQOS, the "qca,disable-hibernation-mode"
property is used for this purpose and has already been submitted to the
upstream, for more details please refer to the below link:
https://lore.kernel.org/netdev/20220818030054.1010660-2-wei.fang@nxp.com/

This issue is easy to reproduce, just unplug the cable and "ifconfig eth0
down", after about 10 senconds, then "ifconfig eth0 up", you will see
failure log on the serial port. The log is shown as following:
root@imx8dxlevk:~#
[34.941970] imx-dwmac 5b050000.ethernet eth0: Link is Down
root@imx8dxlevk:~# ifconfig eth0 down
[35.437814] imx-dwmac 5b050000.ethernet eth0: FPE workqueue stop
[35.507913] imx-dwmac 5b050000.ethernet eth0: PHY [stmmac-1:00] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[35.518613] imx-dwmac 5b050000.ethernet eth0: configuring for phy/rgmii-id link mode
root@imx8dxlevk:~# ifconfig eth0 up
[71.143044] imx-dwmac 5b050000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[71.215855] imx-dwmac 5b050000.ethernet eth0: PHY [stmmac-1:00] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[72.230417] imx-dwmac 5b050000.ethernet: Failed to reset the dma
[72.236512] imx-dwmac 5b050000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[72.245258] imx-dwmac 5b050000.ethernet eth0: __stmmac_open: Hw setup failed
SIOCSIFFLAGS: Connection timed out

After applying this patch, the software reset of EQOS will be
successful. And the log is shown as below.
root@imx8dxlevk:~# ifconfig eth0 up
[96.114344] imx-dwmac 5b050000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[96.171466] imx-dwmac 5b050000.ethernet eth0: PHY [stmmac-1:00] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[96.188883] imx-dwmac 5b050000.ethernet eth0: No Safety Features support found
[96.196221] imx-dwmac 5b050000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[96.204846] imx-dwmac 5b050000.ethernet eth0: registered PTP clock
[96.225558] imx-dwmac 5b050000.ethernet eth0: FPE workqueue start
[96.236858] imx-dwmac 5b050000.ethernet eth0: configuring for phy/rgmii-id link mode
[96.249358] 8021q: adding VLAN 0 to HW filter on device eth0
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC on this Variscite SOM and its MX8MM variant lists regulator-name
for all LDOs except this LDO5, add the regulator-name property to avoid
this omission.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The "regulator-compatible" property is deprecated and unused, as the
match happens on the node name in Linux of_regulator_match() in case
the property is not present. Drop the deprecated property from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The "regulator-compatible" property is deprecated and unused, as the
match happens on the node name in Linux of_regulator_match() in case
the property is not present. Drop the deprecated property from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The "regulator-compatible" property is deprecated and unused, as the
match happens on the node name in Linux of_regulator_match() in case
the property is not present. Drop the deprecated property from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SMMUv2 driver for MMU-500 reads the ARM_SMMU_GR0_ID0 register at
probe time and tries to determine based on the CTTW (Coherent
Translation Table Walk) bit whether this feature is supported.

Unfortunately, it looks like the SMMU integration in the NXP LS1088A has
wrongly tied the cfg_cttw signal to 0, even though the SoC documentation
specifies that "The SMMU supports cache coherency for page table walks
and DVM transactions for page table cache maintenance operations."

Device tree provides the option of overriding the ID register via the
dma-coherent property since commit bae2c2d4 ("iommu/arm-smmu: Sort
out coherency"), and that's what we do here.

Telling struct io_pgtable_cfg that the SMMU page table walks are
coherent with the CPU caches brings performance benefits, because it
avoids certain operations such as __arm_lpae_sync_pte() for PTE updates.

Link: https://lore.kernel.org/linux-iommu/3f3112e4-65ff-105d-8cd7-60495ec9054a@arm.com/Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SMMUv2 driver for MMU-500 reads the ARM_SMMU_GR0_ID0 register at
probe time and tries to determine based on the CTTW (Coherent
Translation Table Walk) bit whether this feature is supported.

Unfortunately, it looks like the SMMU integration in the NXP LS1028A has
wrongly tied the cfg_cttw signal to 0, even though the SoC documentation
specifies that "The SMMU supports cache coherency for page table walks
and DVM transactions for page table cache maintenance operations."

Device tree provides the option of overriding the ID register via the
dma-coherent property since commit bae2c2d4 ("iommu/arm-smmu: Sort
out coherency"), and that's what we do here.

Telling struct io_pgtable_cfg that the SMMU page table walks are
coherent with the CPU caches brings performance benefits, because it
avoids certain operations such as __arm_lpae_sync_pte() for PTE updates.

Link: https://lore.kernel.org/linux-iommu/3f3112e4-65ff-105d-8cd7-60495ec9054a@arm.com/Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a device tree file describing the Debix Model A board from
Polyhex Technology Co.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

By coding style, unit address should not start with 0x.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The TMU TASR, TCALIVn, TRIM registers must be explicitly programmed with
calibration values in OCOTP. Add the OCOTP calibration values phandle so
the TMU driver can perform this programming.

The MX8MM/MX8MN TMUv1 uses only one OCOTP cell, while MX8MP TMUv2 uses 4.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The mapping from OCOTP reg DT property to Fusemap Descriptions Table in
the datasheet is often unclear. Add a comment to make it easier to find
out how it works. No functional change.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Align the SoC unique ID DT node unit address with its reg property.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Fixes: cbff2379 ("arm64: dts: imx8m: add NVMEM provider and consumer to read soc unique ID")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As Documentation/leds/well-known-leds.txt says, "Phones usually have
multi-color status LED." Fix that for the Librem 5 mobile phone board.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add aliases for the RTCs on the board and on the SoC. This ensures that
the primary RTC is always the one on the board that has a buffered supply
and maximum accuracy.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add hot plug detect gpio to the HDMI connector.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node names should be generic and DT schema expects certain pattern:

  freescale/imx8mm-emcon-avari.dtb: leds: 'green', 'red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Disable usb over-current of the chipidea driver on all Carrier-Boards
used by Toradex. Do this as we don't want to use this functionality on
our Carrier Boards and to leave it open to someone who includes our
module-level device-trees.

Remove the now obsolete disable-over-current flag from module-level
device-tree imx8mm-verdin.dtsi and leave it as already mentioned to
the people actually implementing the carrier-board to implement this.

This will prevent the warning "No over current polarity defined" from
being printed on boot.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add flexcan1 and flexcan2 nodes.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown".  After a timer is set to this state, then it can no
longer be re-armed.

The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed.  It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.

This was created by using a coccinelle script and the following
commands:

    $ cat timer.cocci
    @@
    expression ptr, slab;
    identifier timer, rfield;
    @@
    (
    -       del_timer(&ptr->timer);
    +       timer_shutdown(&ptr->timer);
    |
    -       del_timer_sync(&ptr->timer);
    +       timer_shutdown_sync(&ptr->timer);
    )
      ... when strict
          when != ptr->timer
    (
            kfree_rcu(ptr, rfield);
    |
            kmem_cache_free(slab, ptr);
    |
            kfree(ptr);
    )

    $ spatch timer.cocci . > /tmp/t.patch
    $ patch -p1 < /tmp/t.patch

Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull spi fix from Mark Brown:
 "One driver specific change here which handles the case where a SPI
  device for some reason tries to change the bus speed during a message
  on fsl_spi hardware, this should be very unusual"

* tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: fsl_spi: Don't change speed while chipselect is active

Merge tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "Two core fixes here, one for a long standing race which some Qualcomm
  systems have started triggering with their UFS driver and another
  fixing a problem with supply lookup introduced by the fixes for devm
  related use after free issues that were introduced in this merge
  window"

* tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: core: fix deadlock on regulator enable
  regulator: core: Fix resolve supply lookup issue

Pull coccicheck update from Julia Lawall:
 "Modernize use of grep in coccicheck:

  Use 'grep -E' instead of 'egrep'"

* tag 'coccinelle-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  scripts: coccicheck: use "grep -E" instead of "egrep"

Pull kernel hardening fixes from Kees Cook:

 - Fix CFI failure with KASAN (Sami Tolvanen)

 - Fix LKDTM + CFI under GCC 7 and 8 (Kristina Martsenko)

 - Limit CONFIG_ZERO_CALL_USED_REGS to Clang > 15.0.6 (Nathan
   Chancellor)

 - Ignore "contents" argument in LoadPin's LSM hook handling

 - Fix paste-o in /sys/kernel/warn_count API docs

 - Use READ_ONCE() consistently for oops/warn limit reading

* tag 'hardening-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  cfi: Fix CFI failure with KASAN
  exit: Use READ_ONCE() for all oops/warn limit reads
  security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
  lkdtm: cfi: Make PAC test work with GCC 7 and 8
  docs: Fix path paste-o for /sys/kernel/warn_count
  LoadPin: Ignore the "contents" argument of the LSM hooks

Pull pstore fixes from Kees Cook:

 - Switch pmsg_lock to an rt_mutex to avoid priority inversion (John
   Stultz)

 - Correctly assign mem_type property (Luca Stefani)

* tag 'pstore-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore: Properly assign mem_type property
  pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES
  pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion

Pull dma-mapping fixes from Christoph Hellwig:
 "Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
  allocator, as it copes with that just as badly as the coherent
  allocator, and then add a check to make sure no one passes the flag
  ever again"

* tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: reject GFP_COMP for noncoherent allocations
  ALSA: memalloc: don't use GFP_COMP for non-coherent dma allocations

Pull 9p updates from Dominique Martinet:

 - improve p9_check_errors to check buffer size instead of msize when
   possible (e.g. not zero-copy)

 - some more syzbot and KCSAN fixes

 - minor headers include cleanup

* tag '9p-for-6.2-rc1' of https://github.com/martinetd/linux:
  9p/client: fix data race on req->status
  net/9p: fix response size check in p9_check_errors()
  net/9p: distinguish zero-copy requests
  9p/xen: do not memcpy header into req->rc
  9p: set req refcount to zero to avoid uninitialized usage
  9p/net: Remove unneeded idr.h #include
  9p/fs: Remove unneeded idr.h #include

Pull more sound updates from Takashi Iwai:
 "A few more updates for 6.2: most of changes are about ASoC
  device-specific fixes.

   - Lots of ASoC Intel AVS extensions and refactoring

   - Quirks for ASoC Intel SOF as well as regression fixes

   - ASoC Mediatek and Rockchip fixes

   - Intel HD-audio HDMI workarounds

   - Usual HD- and USB-audio device-specific quirks"

* tag 'sound-6.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
  ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
  ALSA: azt3328: Remove the unused function snd_azf3328_codec_outl()
  ASoC: lochnagar: Fix unused lochnagar_of_match warning
  ASoC: Intel: Add HP Stream 8 to bytcr_rt5640.c
  ASoC: SOF: mediatek: initialize panic_info to zero
  ASoC: rt5670: Remove unbalanced pm_runtime_put()
  ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
  ASoC: Intel: soc-acpi: update codec addr on 0C11/0C4F product
  ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in rk_spdif_runtime_resume()
  ASoC: wm8994: Fix potential deadlock
  ASoC: mediatek: mt8195: add sof be ops to check audio active
  ASoC: SOF: Revert: "core: unregister clients and machine drivers in .shutdown"
  ASoC: SOF: Intel: pci-tgl: unblock S5 entry if DMA stop has failed"
  ALSA: hda/hdmi: fix stream-id config keep-alive for rt suspend
  ALSA: hda/hdmi: set default audio parameters for KAE silent-stream
  ALSA: hda/hdmi: fix i915 silent stream programming flow
  ALSA: hda: Error out if invalid stream is being setup
  ASoC: dt-bindings: fsl-sai: Reinstate i.MX93 SAI compatible string
  ASoC: soc-pcm.c: Clear DAIs parameters after stream_active is updated
  ASoC: codecs: wcd-clsh: Remove the unused function
  ...