The following patch relative to CVS from 20060324 adds the following
features to the Realtek HDA codec.

1) Define two new pin modes: ALC_PIN_DIR_IN_NOMICBIAS and
   ALC_PIN_DIR_INOUT_NOMICBIAS.  These can be used with jack mode switch
   definitions in mixers to prevent the user being offered the mic bias
   options if the hardware doesn't support it.

2) Add the ability to have different input mux definitions for different
   ADCs.  This is needed because the ALC260 chip uses different mux layouts
   for the two onboard ADCs.  A new field (num_mux_defs) was added to the
   alc_spec and alc_config_preset structures to support this.

3) Adjust numerous comments to make them consistent with the above changes.

4) Utilise the new multi-mux definition functionality for the ALC260 fujitsu
   model to allow recording of the mixer output.

5) Utilise the new multi-mux definition functionality for the ALC260 test
   model to make the mux selections a little less confusing.

6) Allow the headphone jack of the ALC260 acer model to be retasked in
   the mixer.

6) Utilise the new multi-mux definition functionality for the ALC260 acer
   model to give access to the mixer output and the retasked headphone
   jack.

At this stage the *_NOMICBIAS modes are not used.  We have reports that the
"Line" jack of at least some Acer models doesn't pass the bias out, and we
also know that NIDs 0x0f and 0x10 don't seem to accept the mic bias requests
at all.  However, I feel we need to collect more evidence on both counts
before committing to the use of *_NOMICBIAS.  In the case of the Acers, it's
not clear whether this issue (probably caused by the inclusion of DC
blocking capacitors) affects all Acer models or just a small number.  With
the issue with NIDs 0x0f and 0x10 it's unclear whether this is a hardware
bug which will be addressed in later chip revisions or if it's an
intentional restriction.  The datasheet makes no mention of the restriction
so at this stage I'm inclined to consider it a hardware bug.  Comments in
the source reflect this reasoning.

On a similar theme, the headphone jack of the Fujitsu S7020 also doesn't
appear to pass mic bias voltage.  I'm still investigating this however.

With the ability to retask the headphone jack, owners of ALC260-based Acer
laptops should now be able to record 4 channels of audio if they desire. The
multiple mux definitions allow this jack to be presented from both ADCs
(since this mux input is one of those which differs between the muxes).

This patch has been tested on a Fujitsu S7020 laptop and appears to behave
itself both for the "test" and "fujitsu" models.  Definitions using only a
single mux specification also work.  Other ALC chips should be fine but I
cannot test these myself.  The "auto" modes should also continue to function
but again I have not verified this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Attached you'll find an ALSA driver for AdLib FM cards. An AdLib card is
just an OPL2, which was already supported by sound/drivers/opl3, so only
very minimal bus-glue is needed. The patch applies cleanly to both
2.6.16 and 2.6.16-mm1.

The driver has been tested with an actual ancient 8-bit ISA AdLib card
and works fine. It also works fine for an OPL3 {,emulation} as still
found on many ISA soundcards but given that AdLib cards don't have their
own mixer, upping the volume from 0 might be a problem without the card
driver already loaded and driving the OPL3.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

- Fix possible race of referring the setup hook from the running PCM
- Fix memory leak in an error path of proc write
- Clean up the setup hook parser
Signed-off-by: Takashi Iwai <tiwai@suse.de>

- Clean up initialization and destruction of substream instance
  Now snd_pcm_open_substream() alone does most initialization jobs.
  Add pcm_release callback for cleaning up at snd_pcm_release_substream()
- Tidy up PCM oss code
Signed-off-by: Takashi Iwai <tiwai@suse.de>

- Make snd_pcm_prepare() static
- Clean up snd_pcm_kernel_*_ioctl() functions, reduce exports
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fix the wrong check of enable option in cmi8330 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fixed the compilation, removing obsolete kfree_nocheck() call
for memory debugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fixed the compilation, removing obsolete kfree_nocheck() call
for memory debugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added snd-als300 driver for Avance Logic ALS300/ALS300+ soundcards
by Ash Willis.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add snd-riptide driver for Conexant Riptide chip by Peter Gruber.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fixed the noisy output wtih AD1986A 3stack model using 2 channels.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fix the re-initialization of unsolicited events at resume of stac92xx codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Removed from CONFIG_EXPERIMENTAL from CONFIG_SND_CS46XX_NEW_DSP, and
make default to yes.  This option works fine for years.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added snd-miro driver for miroSOUND PCM by Martin Langer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Removed the unused file argument of snd_power_wait().
Signed-off-by: Takashi Iwai <tiwai@suse.de>

I have just discovered I made an error in the register value set in 'Limit
dmx6fire to 6 dacs' patch (bug1472).  The value set should be '2a' not '0a'
as in the original patch, which unintentionally disables the 2nd MPU 401
UART.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added the dxs_support entry for EPoX EP-8KRAI (ALSA bug#1423).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fixed VREF level of Mic inputs on STAC92xx codecs (ALSA bug#1953).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add support of LG LW20 laptop with ALC880 codec (ALSA bug#1572).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Woe be unto he who builds their filesystems as modules.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[ Obscure quote from the infamous geek bible? ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: (24 commits)
  [PARISC] Fix double free when removing HIL drivers
  [PARISC] Add atomic_sub_and_test
  [PARISC] Enabled some NLS modules in a500, b180 and c3000 defconfigs
  [PARISC] Kill duplicated EXPORT_SYMBOL warnings
  [PARISC] Move ioremap EXPORT_SYMBOL from parisc_ksyms.c
  [PARISC] Make local_t use atomic_long_t
  [PARISC] Update defconfigs
  [PARISC] Add PREEMPT support
  [PARISC] More useful readwrite lock helpers
  [PARISC] Convert HIL drivers to use input_allocate_device
  [PARISC] Fixup CONFIG_EISA a bit
  [PARISC] getsockopt should be ENTRY_COMP
  [PARISC] Remove obsolete CONFIG_DEBUG_IOREMAP
  [PARISC] Temporary FIXME for ioremapping EISA regions
  [PARISC] Enable ioremap functionality unconditionally
  [PARISC] Fix stifb with IOREMAP and a 64-bit kernel
  [PARISC] Add CONFIG_HPPA_IOREMAP to conditionally enable ioremap
  [PARISC] Add STRICT_MM_TYPECHECKS
  [PARISC] Fix IOREMAP with a 64-bit kernel
  [PARISC] Add parisc implementation of flush_kernel_dcache_page()
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mad: RMPP support for additional classes
  IB/mad: include GID/class when matching receives
  IB/mthca: Fix section mismatch problems
  IPoIB: Fix oops with raw sockets
  IB/mthca: Fix check of size in SRQ creation
  IB/srp: Fix unmapping of fake scatterlist

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] sata_mv: three bug fixes
  [PATCH] libata: ata_dev_init_params() fixes
  [PATCH] libata: Fix interesting use of "extern" and also some bracketing
  [PATCH] libata: Simplex and other mode filtering logic
  [PATCH] libata - ATA is both ATA and CFA
  [PATCH] libata: Add ->set_mode hook for odd drivers
  [PATCH] libata: BMDMA handling updates
  [PATCH] libata: kill trailing whitespace
  [PATCH] libata: add FIXME above ata_dev_xfermask()
  [PATCH] libata: cosmetic changes in ata_bus_softreset()
  [PATCH] libata: kill E.D.D.

* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: remove drm_{alloc,free}_pages
  drm: sis fix compile warning
  drm: add new radeon PCI ids..
  drm: read breadcrumb in IRQ handler
  drm: fixup i915 breadcrumb read/write
  drm:  remove pointless checks in radeon_state
  drm: fixup improper cast.
  drm: rationalise some pci ids
  drm: Add general-purpose packet for manipulating scratch registers (r300)
  drm: rework radeon memory map (radeon 1.23)
  drm: update r300 register names
  drm: fixup PCI DMA support

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] ioremap() should prefer WB over UC
  [IA64] Add __mca_table to the DISCARD list in gate.lds
  [IA64] Move __mca_table out of the __init section
  [IA64] simplify some condition checks in iosapic_check_gsi_range
  [IA64] correct some messages and fixes some minor things
  [IA64-SGI] fix for-loop in sn_hwperf_geoid_to_cnode()
  [IA64-SGI] sn_hwperf use of num_online_cpus()
  [IA64] optimize flush_tlb_range on large numa box
  [IA64] lazy_mmu_prot_update needs to be aware of huge pages

This enables the caller to migrate pages from one address space page
cache to another.  In buzz word marketing, you can do zero-copy file
copies!
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This adds support for the sys_splice system call. Using a pipe as a
transport, it can connect to files or sockets (latter as output only).

From the splice.c comments:

   "splice": joining two ropes together by interweaving their strands.

   This is the "extended pipe" functionality, where a pipe is used as
   an arbitrary in-memory buffer. Think of a pipe as a small kernel
   buffer that you can use to transfer data from one end to the other.

   The traditional unix read/write is extended with a "splice()" operation
   that transfers data buffers to or from a pipe buffer.

   Named by Larry McVoy, original implementation from Linus, extended by
   Jens to support splicing to files and fixing the initial implementation
   bugs.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

On Thu, Mar 30, 2006 at 08:31:02AM -0500, Dmitry Torokhov wrote:
> Don't do that, its double free. input_unregister_device() normally
> causes release() to be called and free the device. input_free_device
> is only to be called when input_register_device has not been called or
> failed.
>
> Plus you might want to unregister device after closing serio port,
> otherwise your interrupt routine might be referencing already freed
> memory.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Define atomic_sub_and_test to fix build failures.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

With c3000_defconfig and b180_defconfig, FAT couldn't be used
because no NLS modules were built.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Some symbols are exported both in parisc_ksyms.c, and at their
definition site. Nuke the redundant EXPORT_SYMBOL in ksyms to quiet
warnings when vmlinux is linked.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Move ioremap/iounmap EXPORT_SYMBOL to ioremap.c where they belong.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

As done in asm-generic/local.h in mainline. Otherwise local_t was 32-bit
even on a 64-bit kernel.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

spinlock.c needs _can_lock helpers. Rewrite _is_locked helpers to be
_can_lock helpers.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Convert HIL drivers to use input_allocate_device() - avoids crashes.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Fix up some ISA/EISA stuff.

(Note: isa_ accessors have been removed from asm/io.h)
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

compat_sys_getsockopt exists, so we should use that, instead of directly
using sys_getsockopt on 64-bit compiles.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Remove CONFIG_DEBUG_IOREMAP, it's now obsolete and won't work anyway.
Remove it from lib/KConfig since it was only available on parisc.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>