commit 07e19dff upstream.

The 'mst_mutex' is not needed since because 'ubifs_write_master()' is only
called on the mount path and commit path. The mount path is sequential and
there is no parallelism, and the commit path is also serialized - there is only
one commit going on at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 475d0db7 upstream.

total_objects could be 0 and is used as a denom.

While total_objects is a "long", total_objects == 0 unlikely happens for
3.12 and later kernels because 32-bit architectures would not be able to
hold (1 << 32) objects. However, total_objects == 0 may happen for kernels
between 3.1 and 3.11 because total_objects in prune_super() was an "int"
and (e.g.) x86_64 architecture might be able to hold (1 << 32) objects.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit c2ca0fcd upstream.

This patch makes it possible to kill a process looping in
cont_expand_zero. A process may spend a lot of time in this function, so
it is desirable to be able to kill it.

It happened to me that I wanted to copy a piece data from the disk to a
file. By mistake, I used the "seek" parameter to dd instead of "skip". Due
to the "seek" parameter, dd attempted to extend the file and became stuck
doing so - the only possibility was to reset the machine or wait many
hours until the filesystem runs out of space and cont_expand_zero fails.
We need this patch to be able to terminate the process.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 221414db upstream.

Runtime Power Management handling for the sdhci_add_host() failure
case in sdhci_s3c_probe() should match the code in sdhci_s3c_remove()
(which uses pm_runtime_disable() call which matches the earlier
pm_runtime_enable() one).  Fix it.

This patch fixes "BUG: spinlock bad magic on CPU#0, swapper/0/1" and
"Unbalanced pm_runtime_enable!" warnings.

>From the kernel log:
...
[    1.659631] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[    1.665096] BUG: spinlock bad magic on CPU#0, swapper/0/1
[    1.670433]  lock: 0xea01e484, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[    1.677895] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.16.0-next-20140804-00008-ga59480f-dirty #707
[    1.687037] [<c0013ae4>] (unwind_backtrace) from [<c0010d70>] (show_stack+0x10/0x14)
[    1.694740] [<c0010d70>] (show_stack) from [<c04050c8>] (dump_stack+0x68/0xb8)
[    1.701948] [<c04050c8>] (dump_stack) from [<c0052558>] (do_raw_spin_lock+0x15c/0x1a4)
[    1.709848] [<c0052558>] (do_raw_spin_lock) from [<c040a630>] (_raw_spin_lock_irqsave+0x20/0x28)
[    1.718619] [<c040a630>] (_raw_spin_lock_irqsave) from [<c030d7d0>] (sdhci_do_set_ios+0x1c/0x5cc)
[    1.727464] [<c030d7d0>] (sdhci_do_set_ios) from [<c030ddfc>] (sdhci_runtime_resume_host+0x50/0x104)
[    1.736574] [<c030ddfc>] (sdhci_runtime_resume_host) from [<c02462dc>] (pm_generic_runtime_resume+0x2c/0x40)
[    1.746383] [<c02462dc>] (pm_generic_runtime_resume) from [<c0247898>] (__rpm_callback+0x34/0x70)
[    1.755233] [<c0247898>] (__rpm_callback) from [<c02478fc>] (rpm_callback+0x28/0x88)
[    1.762958] [<c02478fc>] (rpm_callback) from [<c02486f0>] (rpm_resume+0x384/0x4ec)
[    1.770511] [<c02486f0>] (rpm_resume) from [<c02488b0>] (pm_runtime_forbid+0x58/0x64)
[    1.778325] [<c02488b0>] (pm_runtime_forbid) from [<c030ea70>] (sdhci_s3c_probe+0x4a4/0x540)
[    1.786749] [<c030ea70>] (sdhci_s3c_probe) from [<c02429cc>] (platform_drv_probe+0x2c/0x5c)
[    1.795076] [<c02429cc>] (platform_drv_probe) from [<c02415f0>] (driver_probe_device+0x114/0x234)
[    1.803929] [<c02415f0>] (driver_probe_device) from [<c024179c>] (__driver_attach+0x8c/0x90)
[    1.812347] [<c024179c>] (__driver_attach) from [<c023ffb4>] (bus_for_each_dev+0x54/0x88)
[    1.820506] [<c023ffb4>] (bus_for_each_dev) from [<c0240df8>] (bus_add_driver+0xd8/0x1cc)
[    1.828665] [<c0240df8>] (bus_add_driver) from [<c0241db8>] (driver_register+0x78/0xf4)
[    1.836652] [<c0241db8>] (driver_register) from [<c00088a4>] (do_one_initcall+0x80/0x1d0)
[    1.844816] [<c00088a4>] (do_one_initcall) from [<c059ac94>] (kernel_init_freeable+0x108/0x1d4)
[    1.853503] [<c059ac94>] (kernel_init_freeable) from [<c0401300>] (kernel_init+0x8/0xe4)
[    1.861568] [<c0401300>] (kernel_init) from [<c000e538>] (ret_from_fork+0x14/0x3c)
[    1.869582] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...
[    1.997047] s3c-sdhci 12530000.sdhci: Unbalanced pm_runtime_enable!
...
[    2.027235] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[    2.032884] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...

Tested on Hardkernel's Exynos4412 based ODROID-U3 board.

Fixes: 9f4e8151 ("mmc: sdhci-s3c: Enable runtime power management")
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit d1419d50 upstream.

Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.

Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.

Fixes: ff984e57 ("mmc: Add realtek pcie sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit d4d11449 upstream.

As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.

Many host controller probe()s are roughly structured as:

*_probe() {
    host = sdhci_pltfm_init();
    mmc_of_parse(host->mmc);
    rc = sdhci_add_host(host);
    if (rc) {
        sdhci_pltfm_free();
        return rc;
    }

In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().

Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().

sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.

This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():

WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18

The object being complained about is host->detect.

There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().

However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.

This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.

The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.

CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 6f67cc6f upstream.

Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.

Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.

Fixes: c7f6558d ("mmc: Add realtek USB sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit b3153765 upstream.

.set_uhs_signaling field is currently initialised twice once to the
arch specific callback pxav3_set_uhs_signaling, and also to the generic
sdhci_set_uhs_signaling callback.

This means that uhs is currently broken for this platform currently, as pxav3
has some special constriants which means it can't use the generic callback.

This happened in
commit 96d7b78c ("mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function")
commit a702c8ab ("mmc: host: split up sdhci-pxa, create sdhci-pxav3.c")'

Fix this and hopefully prevent it happening in the future by ensuring named
initialisers always follow the declaration order in the structure definition.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit dea67c4e upstream.

781e989c ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec6 ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151

In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 31d9f8fa upstream.

Current caching implementation during regcache_sync() call bypasses
all register writes of values that are already known as default
(regmap reg_defaults). Same time in TLV320AIC3x codecs register 5
(AIC3X_PLL_PROGC_REG) write should be immediately followed by register
6 write (AIC3X_PLL_PROGD_REG) even if it was not changed. Otherwise
both registers will not be written.

This brings to issue that appears particulary in case of 44.1kHz
playback with 19.2MHz master clock. In this case AIC3X_PLL_PROGC_REG
is 0x6e while AIC3X_PLL_PROGD_REG is 0x0 (same as register
default). Thus AIC3X_PLL_PROGC_REG also remains not written and we get
wrong playback speed.

In this patch snd_soc_read() is used to get cached pll values and
snd_soc_write() (unlike regcache_sync() this function doesn't bypasses
hardware default values) to write them to registers.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit e5092c96 upstream.

Coverity spotted the following possible use-after-free condition in
dapm_create_or_share_mixmux_kcontrol():

If kcontrol is NULL, and (wname_in_long_name && kcname_in_long_name)
validates to true, 'name' will be set to an allocated string, and be
freed a few lines later via the 'long_name' alias. 'name', however,
is used by dev_err() in case snd_ctl_add() fails.

Fix this by adding a jump label that frees 'long_name' at the end of
the function.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 6d8ca28f upstream.

Currently, ata_sff_softreset is skipped for controllers with no ctl port.
But that also skips ata_sff_dev_classify required for device detection.
This means that libata is currently broken on controllers with no ctl port.

No device connected:
[    1.872480] pata_isapnp 01:01.02: activated
[    1.889823] scsi2 : pata_isapnp
[    1.890109] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    6.888110] ata3.01: qc timeout (cmd 0xec)
[    6.888179] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   16.888085] ata3.01: qc timeout (cmd 0xec)
[   16.888147] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.888086] ata3.01: qc timeout (cmd 0xec)
[   46.888148] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   51.888100] ata3.00: qc timeout (cmd 0xec)
[   51.888160] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[   61.888079] ata3.00: qc timeout (cmd 0xec)
[   61.888141] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[   91.888089] ata3.00: qc timeout (cmd 0xec)
[   91.888152] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)

ATAPI device connected:
[    1.882061] pata_isapnp 01:01.02: activated
[    1.893430] scsi2 : pata_isapnp
[    1.893719] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    6.892107] ata3.01: qc timeout (cmd 0xec)
[    6.892171] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   16.892079] ata3.01: qc timeout (cmd 0xec)
[   16.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.892079] ata3.01: qc timeout (cmd 0xec)
[   46.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.908586] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr
[   46.924570] ata3.00: configured for PIO0 (device error ignored)
[   46.926295] scsi 2:0:0:0: CD-ROM            ACER     CD-767E/O        1.5X PQ: 0 ANSI: 5
[   46.984519] sr0: scsi3-mmc drive: 6x/6x xa/form2 tray
[   46.984592] cdrom: Uniform CD-ROM driver Revision: 3.20

So don't skip ata_sff_softreset, just skip the reset part of ata_bus_softreset
if the ctl port is not available.

This makes IDE port on ES968 behave correctly:

No device connected:
[    4.670888] pata_isapnp 01:01.02: activated
[    4.673207] scsi host2: pata_isapnp
[    4.673675] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    7.081840] Adding 2541652k swap on /dev/sda2.  Priority:-1 extents:1 across:2541652k

ATAPI device connected:
[    4.704362] pata_isapnp 01:01.02: activated
[    4.706620] scsi host2: pata_isapnp
[    4.706877] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    4.872782] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr
[    4.888673] ata3.00: configured for PIO0 (device error ignored)
[    4.893984] scsi 2:0:0:0: CD-ROM            ACER     CD-767E/O        1.5X PQ: 0 ANSI: 5
[    7.015578] Adding 2541652k swap on /dev/sda2.  Priority:-1 extents:1 across:2541652k
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 37017ac6 upstream.

The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
does not support 64-KB DMA transfers.
Whenever a 64-KB DMA transfer is attempted,
the transfer fails and messages similar to the following
are written to the console log:

   [ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
   [ 2431.851139] sr 0:0:0:0: [sr0]  Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
   [ 2431.851152] sr 0:0:0:0: [sr0]  Sense Key : Hardware Error [current]
   [ 2431.851166] sr 0:0:0:0: [sr0]  Add. Sense: Logical unit communication time-out
   [ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
   [ 2431.851210] end_request: I/O error, dev sr0, sector 121808

When the libata and pata_serverworks modules
are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
the 64-KB transfer size in the scatter-gather list can be seen
in the console log:

   [ 2664.897267] sr 9:0:0:0: [sr0] Send:
   [ 2664.897274] 0xf63d85e0
   [ 2664.897283] sr 9:0:0:0: [sr0] CDB:
   [ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00
   [ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700
   [ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40
   [ 2664.897338] ata_scsi_translate: ENTER
   [ 2664.897345] ata_sg_setup: ENTER, ata1
   [ 2664.897356] ata_sg_setup: 3 sg elements mapped
   [ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000)
   [ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000)
   ------------------------------------------------------> =======
   [ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000)
   [ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1
   [ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC
   [ 2664.897428] ata_sff_tf_load: device 0xA0
   [ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0
   [ 2664.897457] ata_scsi_translate: EXIT
   [ 2664.897462] leaving scsi_dispatch_cmnd()
   [ 2664.897497] Doing sr request, dev = sr0, block = 0
   [ 2664.897507] sr0 : reading 64/256 512 byte blocks.
   [ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58)
   [ 2664.897560] atapi_send_cdb: send cdb
   [ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64
   [ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3
   [ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51)
   [ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51)
   [ 2666.910129] sr 9:0:0:0: [sr0] Done:
   [ 2666.910136] 0xf63d85e0 TIMEOUT

lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
pata_serverworks:

   00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
           Flags: bus master, medium devsel, latency 64
           [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
           [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
           I/O ports at 0170 [size=8]
           I/O ports at 0374 [size=4]
           I/O ports at 1440 [size=16]
           Kernel driver in use: pata_serverworks

The pata_serverworks driver supports five distinct device IDs,
one being the OSB4 and the other four belonging to the CSB series.
The CSB series appears to support 64-KB DMA transfers,
as tests on a machine with an SAI2 motherboard
containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
showed no problems with 64-KB DMA transfers.

This problem was first discovered when attempting to install openSUSE
from a DVD on a machine with an STL2 motherboard.
Using the pata_serverworks module,
older releases of openSUSE will not install at all due to the timeouts.
Releases of openSUSE prior to 11.3 can be installed by disabling
the pata_serverworks module using the brokenmodules boot parameter,
which causes the serverworks module to be used instead.
Recent releases of openSUSE (12.2 and later) include better error recovery and
will install, though very slowly.
On all openSUSE releases, the problem can be recreated
on a machine containing a Broadcom OSB4 IDE Controller
by mounting an install DVD and running a command similar to the following:

   find /mnt -type f -print | xargs cat > /dev/null

The patch below corrects the problem.
Similar to the other ATA drivers that do not support 64-KB DMA transfers,
the patch changes the ata_port_operations qc_prep vector to point to a routine
that breaks any 64-KB segment into two 32-KB segments and
changes the scsi_host_template sg_tablesize element to reduce by half
the number of scatter/gather elements allowed.
These two changes affect only the OSB4.
Signed-off-by: Scott Carter <ccscott@funsoft.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit bb2e226b upstream.

This reverts commit 3189eddb ("percpu: free percpu allocation info for
uniprocessor system").

The commit causes a hang with a crisv32 image. This may be an architecture
problem, but at least for now the revert is necessary to be able to boot a
crisv32 image.

Cc: Tejun Heo <tj@kernel.org>
Cc: Honggang Li <enjoymindful@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 3189eddb ("percpu: free percpu allocation info for uniprocessor system")
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 2aca5b86 upstream.

The flag RPC_CLNT_CREATE_NO_RETRANS_TIMEOUT was intended introduced in
order to allow NFSv4 clients to disable resend timeouts. Since those
cause the RPC layer to break the connection, they mess up the duplicate
reply caches that remain indexed on the port number in NFSv4..

This patch includes the code that was missing in the original to
set the appropriate flag in struct rpc_clnt, when the caller of
rpc_create() sets RPC_CLNT_CREATE_NO_RETRANS_TIMEOUT.

Fixes: 8a19a0b6 (SUNRPC: Add RPC task and client level options to...)
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit a743419f upstream.

When aborting a connection to preserve source ports, don't wake the task in
xs_error_report.  This allows tasks with RPC_TASK_SOFTCONN to succeed if the
connection needs to be re-established since it preserves the task's status
instead of setting it to the status of the aborting kernel_connect().

This may also avoid a potential conflict on the socket's lock.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 173b3afc upstream.

If rpc.statd is restarted, upcalls to monitor hosts can fail with
ECONNREFUSED.  In that case force a lookup of statd's new port and retry the
upcall.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit e300180f upstream.

The radeon driver uses placement range restrictions for several reasons,
in particular to make sure BOs in VRAM can be accessed by the CPU, e.g.
during a page fault.

Without this change, TTM could evict other BOs while trying to satisfy
the requested placement, even if the evicted BOs were outside of the
requested placement range. Doing so didn't free up any space in the
requested placement range, so the (potentially high) eviction cost was
incurred for no benefit.

Nominating for stable because radeon driver changes in 3.17 made this
much more noticeable than before.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84662Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ luis: backported to 3.16: based on Michel's backport ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit e2cffb5f upstream.

On archs with PAGE_SIZE >= 64 KiB the function skcipher_alloc_sgl()
fails with -ENOMEM no matter what user space actually requested.
This is caused by the fact sock_kmalloc call inside the function tried
to allocate more memory than allowed by the default kernel socket buffer
size (kernel param net.core.optmem_max).
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 7965ee93 upstream.

The code looks for an already loaded target, and the correct list to search
is nft_target_list, not nft_match_list.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit b51d3fa3 upstream.

The kernel should reserve enough room in the skb so that the DONE
message can always be appended.  However, in case of e.g. new attribute
erronously not being size-accounted for, __nfulnl_send() will still
try to put next nlmsg into this full skbuf, causing the skb to be stuck
forever and blocking delivery of further messages.

Fix issue by releasing skb immediately after nlmsg_put error and
WARN() so we can track down the cause of such size mismatch.

[ fw@strlen.de: add tailroom/len info to WARN ]
Signed-off-by: Houcheng Lin <houcheng@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit c1e7dc91 upstream.

don't try to queue payloads > 0xffff - NLA_HDRLEN, it does not work.
The nla length includes the size of the nla struct, so anything larger
results in u16 integer overflow.

This patch is similar to
9cefbbc9 (netfilter: nfnetlink_queue: cleanup copy_range usage).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 9dfa1dfe upstream.

We currently neither account for the nlattr size, nor do we consider
the size of the trailing NLMSG_DONE when allocating nlmsg skb.

This can result in nflog to stop working, as __nfulnl_send() re-tries
sending forever if it failed to append NLMSG_DONE (which will never
work if buffer is not large enough).
Reported-by: Houcheng Lin <houcheng@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit c123bb71 upstream.

alloc_percpu returns NULL on failure, not a negative error code.

Fixes: ff3cd7b3 ("netfilter: nf_tables: refactor chain statistic routines")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 0f9f5e1b upstream.

The ->ip_set_list[] array is initialized in ip_set_net_init() and it
has ->ip_set_max elements so this check should be >= instead of >
otherwise we are off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit d1585c89 upstream.

This patch adds codec ID (0x80862883) and module alias for Braswell
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit f31b2ffc upstream.

Add HD Audio Device PCI ID for the Intel Braswell platform.
It is an HDA Intel PCH controller.

AZX_DCAPS_ALIGN_BUFSIZE is not necessary for this controller.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 849f5d89 upstream.

Add Braswell PCI ID to list of supported ID's for the IOSF driver.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: http://lkml.kernel.org/r/1411017231-20807-2-git-send-email-david.e.box@linux.intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 16405f98 upstream.

This is pretty much the same as Intel Baytrail, only the CPU ID is
different. Add the new ID to the supported CPU list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 19aeb5a6 upstream.

This patch fixes a regression in the patch "GFS2: Remember directory
insert point", commit 2b47dad8.
The problem had to do with the rename function: The function found
space for the new dirent, and remembered that location. But then the
old dirent was removed, which often moved the eligible location for
the renamed dirent. Putting the new dirent at the saved location
caused file system corruption.

This patch adds a new "save_loc" variable to struct gfs2_diradd.
If 1, the dirent location is saved. If 0, the dirent location is not
saved and the buffer_head is released as per previous behavior.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 595d373f upstream.

Fixes type/mask calculation being based on uninitialised data for VGA
outputs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 5838ae61 upstream.

Reported in fdo#82527 comment #2.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit fe3d9c4b upstream.

A mismatch between FB and LTC's idea of how big a large page is causes
issues such as black "holes" in rendering to occur on some boards
(those where LTC is configured for 64KiB large pages) when compression
is used.

Confirmed to fix at least the GK107 MBP.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 147ed897 upstream.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 3d9e3921 upstream.

Likely a large part of the GK106 woes..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit e7d96929 upstream.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 6fbb702e upstream.

Linus commit 05c63c2f modified the
runtime suspend/resume paths to skip over display-related tasks to
avoid locking issues on resume.

Unfortunately, this resulted in the display hardware being left in
a partially initialised state, preventing subsequent modesets from
completing.

This commit unifies the (many) suspend/resume paths, bringing back
display (and fbcon) handling in the runtime paths.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 634ffccc upstream.

Preparation for some runtime pm fixes.  Currently we skip over fbcon
suspend/resume in the runtime path, which causes issues on resume if
fbcon tries to write to the framebuffer before the BAR subdev has
been resumed to restore the BAR1 VM setup.

As we might be woken up via a sysfs connector, we are unable to call
fb_set_suspend() in the resume path as it could make its way down to
a modeset and cause all sorts of locking hilarity.

To solve this, we'll just delay the fbcon resume to a workqueue.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 04384435 upstream.

This *should* be safe these days.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 4b5098f3 upstream.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>