- 02 May, 2018 37 commits
-
-
Masaharu Hayakawa authored
Sometimes sg->offset is not used for buffer addresses allocated by dma_map_sg(), so alignment checks should be done on the allocated buffer addresses. Delete the alignment check for sg->offset that is done before dma_map_sg(). Instead, it performs the alignment check for sg->dma_address after dma_map_sg(). Signed-off-by:
Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com> [Niklas: broke this commit in two and tidied small style issue] Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> [rebased to mmc/next] Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Niklas Söderlund authored
Instead of directly accessing the members of struct scatterlist use the helpers mmc_get_dma_dir() and sg_dma_address() in renesas_sdhi_internal_dmac_start_dma(). Based on previous work by Masaharu Hayakawa. Signed-off-by:
-
Kyle Roeschley authored
On some NI 904x devices, using 3.3V signaling for extended periods of time will physically damage the pads connected to the SDHC, eventually causing complete failure of the controller. To work around this, require that we avoid 3.3V signaling. Signed-off-by:
Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by:
Jennifer Dahm <jennifer.dahm@ni.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Kyle Roeschley authored
Some SD host controllers cannot handle extended use of 3.3V signaling. To accommodate these controllers, add a capability that requires us to negotiate the voltage down from 3.3V during card initialization. Signed-off-by:
-
Geert Uytterhoeven authored
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST". In most cases this other symbol is an architecture or platform specific symbol, or PCI. Generic symbols and drivers without platform dependencies keep their dependencies on HAS_DMA, to prevent compiling subsystems or drivers that cannot work anyway. This simplifies the dependencies, and allows to improve compile-testing. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by:
Mark Brown <broonie@kernel.org> Acked-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
-
Maxime Ripard authored
Our set_ios hook is, when the card is power up or down, either doing a full init or put our controller back into a reset mode. Since we're also doing that in our runtime_pm hooks, and at possibly much more often, we can drop it from the set_ios, and either rely on our runtime_pm hooks or our probe to do it. Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Maxime Ripard authored
So far, even if our card was not in use, we didn't shut down our MMC controller, which meant that it was still active and clocking the bus. While this obviously means that we could save some power there, it also creates issues when it comes to EMC control since we'll have a perfect peak at the card clock rate. Let's implement runtime_pm with autosuspend so that we will shut down the controller when it's not been in use for quite some time. Signed-off-by:
-
Maxime Ripard authored
In order to improve readibility and reusability, let's move the card setup to a small function called by our .set_ios hook. Signed-off-by:
-
Maxime Ripard authored
In order to improve readibility and reusability, let's move the clock setup to a small function called by our .set_ios hook. Signed-off-by:
-
Maxime Ripard authored
In order to improve readibility and reusability, let's move the bus width setup to a small function called by our .set_ios hook. Signed-off-by:
-
Maxime Ripard authored
All the other functions in the driver take a struct sunxi_mmc_host pointer. Let's make it consistent. Signed-off-by:
-
Maxime Ripard authored
Our headers sort algorithm has had pretty chaotic results. Let's fix that. Signed-off-by:
-
Ezequiel Garcia authored
Now that we have MMC support, enable ext2/3/4 support in the CI20 defconfig. Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Acked-by:
James Hogan <jhogan@kernel.org> Signed-off-by:
-
Diwakar Sharma authored
This patch uses limit clock rate quirk to reduce clock rate for "SDR104" mode on IMX side for Marvell 8887 WiFi + Bluetooth chip side, as Marvell does not recommend to use SDIO at the speed of higher than 150MHz. Signed-off-by:
Diwakar Sharma <diwakar.sharma@in.bosch.com> Signed-off-by:
Harish Jenny K N <harish_kandiga@mentor.com> Signed-off-by:
-
harish_kandiga@mentor.com authored
This patch adds a quirk to limit clock rate which can be used to reduce the SDIO clock rate for some chips with broken UHS. Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
-
Shawn Lin authored
DDR52 with 8-bit mode should be handled in a different way when requesting ciu_clk. However DDR50 is used for SDMMC/SDIO and could never be possible with 8-bit mode. It's trival but misleading. Signed-off-by:
-
Masahiro Yamada authored
Cadence sent out an errata report to their customers of this IP. This errata is not so severe, but the tune request should be sent twice to avoid the potential issue. Quote from the report: Problem Summary --------------- The IP6116 SD/eMMC PHY design has a timing issue on receive data path. This issue may lead to an incorrect values of read/write pointers of the synchronization FIFO. Such a situation can happen at the SDR104 and HS200 tuning procedure when the PHY is requested to change a phase of sampling clock when moving to the next tuning iteration. Workarounds ----------- The following are valid workarounds to resolve the issue: 1. In eMMC mode, software sends tune request twice instead of once at each iteration. This means that the clock phase is not changed on the second request so there is no potential for clock instability. 2. In SD mode, software must not use the hardware tuning and instead perform an almost identical procedure to eMMC, using the HRS34 Tune Force register. Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Nan Li authored
Explicitly update the docomentation to support the Meson-AXG platform. Signed-off-by:
Nan Li <nan.li@amlogic.com> Signed-off-by:
Yixun Lan <yixun.lan@amlogic.com> Signed-off-by:
Kevin Hilman <khilman@baylibre.com>
-
Nan Li authored
Introduce the compatible data to cover the register offset & mask change of the eMMC controller in Amlogic's Meson-AXG SoC. Signed-off-by:
-
Nan Li authored
Update the documentation to list support for Meson-AXG SoC explicitly. The new binding string is necessary since this SoC introduce a few IP difference comparing to previous old generation. Signed-off-by:
-
Andrew Gabbasov authored
Since RPMB area is accessible via special ioctl only and boot areas are unlikely to contain any partitions, exclude them all from listing in /proc/partitions. This will hide them from various user-level software (e.g. fdisk), thus avoiding unnecessary access attempts. Signed-off-by:
Andrew Gabbasov <andrew_gabbasov@mentor.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Ezequiel Garcia authored
Enable the SD/MMC support, along with DMA engine support in the CI20 defconfig. Acked-by:
Mathieu Malaterre <malat@debian.org> Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.co.uk> Signed-off-by:
-
Ezequiel Garcia authored
Now that we have support for JZ480 SoCs in the MMC driver, let's enable it on the devicetree. Acked-by:
-
Ezequiel Garcia authored
Add the devicetree node to support the MMC host controller available in JZ480 SoCs. Acked-by:
-
Ezequiel Garcia authored
Add the devicetree node to support the DMA controller found in JZ480 SoCs. Tested-by:
-
Ezequiel Garcia authored
Replace dma_request_channel() with dma_request_chan(), which also supports probing from the devicetree. Tested-by:
-
Alex Smith authored
Add support for the JZ4780 MMC controller to the jz47xx_mmc driver. There are a few minor differences from the 4740 to the 4780 that need to be handled, but otherwise the controllers behave the same. The IREG and IMASK registers are expanded to 32 bits. Additionally, some error conditions are now reported in both STATUS and IREG. Writing IREG before reading STATUS causes the bits in STATUS to be cleared, so STATUS must be read first to ensure we see and report error conditions correctly. Signed-off-by:
Alex Smith <alex.smith@imgtec.com> Signed-off-by:
Paul Cercueil <paul@crapouillou.net> Tested-by:
-
Alex Smith authored
The maximum clock rate can be overridden by DT. The clock rate should be set to the DT-specified value rather than the constant JZ_MMC_CLK_RATE when this is done. If the maximum clock rate is not set by DT then mmc->f_max will be set to JZ_MMC_CLK_RATE. Tested-by:
-
Ezequiel Garcia authored
Add the devicetree binding for JZ4740/JZ4780 SoC MMC/SD controller. Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Ezequiel Garcia authored
Add support to probe the device via devicetree, which will be used to support other SoCs such as the JZ4780. Based on commits from the CI20 repo, by Paul Cercueil and Alex Smith. Binding document based on work by Zubair Lutfullah Kakakhel. Tested-by:
-
Zubair Lutfullah Kakakhel authored
In case a bootloader leaves the device in a bad state, requesting the interrupt before resetting results in a bad interrupt loop. Signed-off-by:
Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> [Ezequiel: cleanup commit description] Tested-by:
-
Ezequiel Garcia authored
Instead of accessing the platform data pointer directly, use the dev_get_platdata() helper. Tested-by:
-
Ezequiel Garcia authored
Just a minor cleanup to order the headers alphabetically. This helps prevent merge conflicts. Tested-by:
-
Paul Cercueil authored
Currently, if jz4740_mmc_request_gpios() fails, the driver tries to release DMA resources. This is wrong because DMA is requested at a later stage. Signed-off-by:
-
Shawn Lin authored
Respect the actual clock for mmc debugfs to help better debug the hardware. mmc_host mmc0: Bus speed (slot 0) = 135475200Hz (slot req 150000000Hz, actual 135475200HZ div = 0) cat /sys/kernel/debug/mmc0/ios clock: 150000000 Hz actual clock: 135475200 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 3 (8 bits) timing spec: 9 (mmc HS200) signal voltage: 0 (1.80 V) driver type: 0 (driver type B) Cc: Xiao Yao <xiaoyao@rock-chips.com> Cc: Ziyuan <xzy.xu@rock-chips.com> Signed-off-by:
-
Tobin C. Harding authored
The use of stack Variable Length Arrays needs to be avoided, as they can be a vector for stack exhaustion, which can be both a runtime bug (kernel Oops) or a security flaw (overwriting memory beyond the stack). Also, in general, as code evolves it is easy to lose track of how big a VLA can get. Thus, we can end up having runtime failures that are hard to debug. As part of the directive[1] to remove all VLAs from the kernel, and build with -Wvla. Currently driver is using a VLA declared using the number of descriptors. This array is used to store integer values and is later used as an argument to `gpiod_set_array_value_cansleep()` This can be avoided by using `kmalloc_array()` to allocate memory for the array of integer values. Memory is free'd before return from function. >From the code it appears that it is safe to sleep so we can use GFP_KERNEL (based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`. It can be expected that this patch will result in a small increase in overhead due to the use of `kmalloc_array()` [1] https://lkml.org/lkml/2018/3/7/621Signed-off-by:
Tobin C. Harding <me@tobin.cc> Signed-off-by:
-
Phil Edworthy authored
On SD 2.00 cards we get lots of these messages: "mmc0: Got data interrupt 0x00000002 even though no data operation was in progress" By applying the SDHCI_QUIRK2_STOP_WITH_TC quirk, the messages no longer happen. A single card claiming to be SD 3.00 compliant also generates the interrupts, but since the card's manfacturing date is 2002 mar, it's unlikely to really be SD 3.00. This card is a 8GB SanDisk 'SU08G' 8.0 (SDHC class 4). This has been reported on Xilinx devices that also use the Arasan IP. See https://patchwork.kernel.org/patch/8062871/ This has been tested on the Renesas RZ/ND-DB board with the RZ/N1 SoC. The Arasan IP in this device is version 1.39a and uses a max SD clock of 50MHz and does not support DDR modes. Signed-off-by:
Phil Edworthy <phil.edworthy@renesas.com> Acked-by:
-
- 29 Apr, 2018 3 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "Another set of x86 related updates: - Fix the long broken x32 version of the IPC user space headers which was noticed by Arnd Bergman in course of his ongoing y2038 work. GLIBC seems to have non broken private copies of these headers so this went unnoticed. - Two microcode fixlets which address some more fallout from the recent modifications in that area: - Unconditionally save the microcode patch, which was only saved when CPU_HOTPLUG was enabled causing failures in the late loading mechanism - Make the later loader synchronization finally work under all circumstances. It was exiting early and causing timeout failures due to a missing synchronization point. - Do not use mwait_play_dead() on AMD systems to prevent excessive power consumption as the CPU cannot go into deep power states from there. - Address an annoying sparse warning due to lost type qualifiers of the vmemmap and vmalloc base address constants. - Prevent reserving crash kernel region on Xen PV as this leads to the wrong perception that crash kernels actually work there which is not the case. Xen PV has its own crash mechanism handled by the hypervisor. - Add missing TLB cpuid values to the table to make the printout on certain machines correct. - Enumerate the new CLDEMOTE instruction - Fix an incorrect SPDX identifier - Remove stale macros" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/ipc: Fix x32 version of shmid64_ds and msqid64_ds x86/setup: Do not reserve a crash kernel region if booted on Xen PV x86/cpu/intel: Add missing TLB cpuid values x86/smpboot: Don't use mwait_play_dead() on AMD systems x86/mm: Make vmemmap and vmalloc base address constants unsigned long x86/vector: Remove the unused macro FPU_IRQ x86/vector: Remove the macro VECTOR_OFFSET_START x86/cpufeatures: Enumerate cldemote instruction x86/microcode: Do not exit early from __reload_late() x86/microcode/intel: Save microcode patch unconditionally x86/jailhouse: Fix incorrect SPDX identifier -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 pti fixes from Thomas Gleixner: "A set of updates for the x86/pti related code: - Preserve r8-r11 in int $0x80. r8-r11 need to be preserved, but the int$80 entry code removed that quite some time ago. Make it correct again. - A set of fixes for the Global Bit work which went into 4.17 and caused a bunch of interesting regressions: - Triggering a BUG in the page attribute code due to a missing check for early boot stage - Warnings in the page attribute code about holes in the kernel text mapping which are caused by the freeing of the init code. Handle such holes gracefully. - Reduce the amount of kernel memory which is set global to the actual text and do not incidentally overlap with data. - Disable the global bit when RANDSTRUCT is enabled as it partially defeats the hardening. - Make the page protection setup correct for vma->page_prot population again. The adjustment of the protections fell through the crack during the Global bit rework and triggers warnings on machines which do not support certain features, e.g. NX" * 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/entry/64/compat: Preserve r8-r11 in int $0x80 x86/pti: Filter at vma->vm_page_prot population x86/pti: Disallow global kernel text with RANDSTRUCT x86/pti: Reduce amount of kernel text allowed to be Global x86/pti: Fix boot warning from Global-bit setting x86/pti: Fix boot problems from Global-bit setting
-
