These patches all fix bugs that were newly introduced in v3.6-rc1
and found because they cause a gcc warning with one of the ARM
defconfigs. Most of them are harmless, but since we're trying
to get rid of all warnings eventually, we can start with the ones
that were not there before.

* testing/new-warnings:
  omap-rng: fix use of SIMPLE_DEV_PM_OPS
  spi/s3c64xx: improve error handling
  mtd/omap2: fix dmaengine_slave_config error handling
  gpio: em: do not discard em_gio_irq_domain_cleanup
  ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
  usb/ohci-omap: remove unused variable
  mfd/asic3: fix asic3_mfd_probe return value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

omap_rng_suspend and omap_rng_resume are unused if CONFIG_PM is enabled
but CONFIG_PM_SLEEP is disabled. I found this while building all defconfig
files on ARM. It's not clear to me if this is the right solution, but
at least it makes the code consistent again.

Without this patch, building omap1_defconfig results in:

drivers/char/hw_random/omap-rng.c:165:12: warning: 'omap_rng_suspend' defined but not used [-Wunused-function]
drivers/char/hw_random/omap-rng.c:171:12: warning: 'omap_rng_resume' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kevin Hilman <khilman@ti.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Herbert Xu <herbert@gondor.apana.org.au>

When a device tree definition os an s3c64xx SPI master is missing
a "controller-data" subnode, the newly added s3c64xx_get_slave_ctrldata
function might use uninitialized memory in place of that node,
which was correctly reported by gcc.

Without this patch, building s3c6400_defconfig results in:

drivers/spi/spi-s3c64xx.c: In function 's3c64xx_get_slave_ctrldata.isra.25':
drivers/spi/spi-s3c64xx.c:841:5: warning: 'data_np' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jaswinder Singh <jaswinder.singh@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>

The newly added dmaengine support in the omap2 nand driver
potentially causes an undefined return value from the
omap_nand_probe function when dmaengine_slave_config
reports an error. Let's handle this by returning the
same error back to the caller.

Without this patch, building omap2plus_defconfig results in:

drivers/mtd/nand/omap2.c: In function 'omap_nand_probe':
drivers/mtd/nand/omap2.c:1154:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>

The newly added gpio-em driver marks its em_gio_irq_domain_cleanup
function as __devexit, which would lead to that function being
discarded in case CONFIG_HOTPLUG is disabled. However, the function
is also called by the error handling logic em_gio_probe, which
would cause a jump into a NULL pointer if it was removed from the
kernel or module.

Without this patch, building kzm9d_defconfig results in:

WARNING: drivers/gpio/built-in.o(.devinit.text+0x330): Section mismatch in reference from the function em_gio_probe() to the function .devexit.text:em_gio_irq_domain_cleanup()
The function __devinit em_gio_probe() references
a function __devexit em_gio_irq_domain_cleanup().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
em_gio_irq_domain_cleanup() so it may be used outside an exit section.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>

exynos_pm_add_dev_to_genpd is used if one or more out of a large
number of Kconfig symbols are enabled. However the new
exynos_defconfig selects none of those, so the function becomes
unused. Marking it so lets the compiler automatically discard
it.

Without this patch, building exynos_defconfig results in:

arch/arm/mach-exynos/pm_domains.c:118:123: warning: 'exynos_pm_add_dev_to_genpd' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>

It is not currently possible to build the gpmi-nand driver without
also building the mxs-dma driver. Clarify this Kconfig and enable
both in the defconfig file so we can build it again with both enabled.

drivers/built-in.o: In function `gpmi_dma_filter':
clk-fixed-factor.c:(.text+0xafc18): undefined reference to `mxs_dma_is_apbh'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>

Without this patch, building integrator_defconfig results in:

arch/arm/mach-integrator/core.c:150:1: warning: data definition has no type or storage class [enabled by default]
arch/arm/mach-integrator/core.c:150:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/arm/mach-integrator/core.c:150:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>

The samsung PWM driver has moved to the new PWM subsystem, which
changed the Kconfig symbol for that driver, but the rx1950 and
gta02 boards still uses the old one.

Without this patch, building s3c2410_defconfig results in:

arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_lcd_power':
arch/arm/mach-s3c24xx/mach-rx1950.c:430: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:431: undefined reference to `pwm_disable'
arch/arm/mach-s3c24xx/mach-rx1950.c:437: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:438: undefined reference to `pwm_enable'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_exit':
arch/arm/mach-s3c24xx/mach-rx1950.c:504: undefined reference to `pwm_free'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_init':
arch/arm/mach-s3c24xx/mach-rx1950.c:487: undefined reference to `pwm_request'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>

The sa1100 definition of the io_p2v macro has changed in v3.6, and this one
file stopped working because of that.

Without this patch, building hackkit_defconfig results in:

arch/arm/mach-sa1100/leds-hackkit.c: In function 'hackkit_leds_event':
arch/arm/mach-sa1100/leds-hackkit.c:39:4: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>

The EETI touchscreen asserts its IRQ line as soon as it has data in its
internal buffers. The line is automatically deasserted once all data has
been read via I2C. Hence, the driver has to monitor the GPIO line and
cannot simply rely on the interrupt handler reception.

In the current implementation of the driver, irq_to_gpio() is used to
determine the GPIO number from the i2c_client's IRQ value.

As irq_to_gpio() is not available on all platforms, this patch changes
this and makes the driver ignore the passed in IRQ. Instead, a GPIO is
added to the platform_data struct and gpio_to_irq is used to derive the
IRQ from that GPIO. If this fails, bail out. The driver is only able to
work in environments where the touchscreen GPIO can be mapped to an
IRQ.

Without this patch, building raumfeld_defconfig results in:

drivers/input/touchscreen/eeti_ts.c: In function 'eeti_ts_irq_active':
drivers/input/touchscreen/eeti_ts.c:65:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-input@vger.kernel.org
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>

The irq_to_gpio function was removed from the pxa platform
in linux-3.2, and this driver has been broken since.

There is actually no in-tree user of this driver that adds
this platform device, but the driver can and does get enabled
on some platforms.

Without this patch, building ezx_defconfig results in:

drivers/mfd/ezx-pcap.c: In function 'pcap_isr_work':
drivers/mfd/ezx-pcap.c:205:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>

Commit 3d55c29f "ARM: tegra: harmony: add regulator supply name and its
input supply" was supposed to fix all the problems with regulators on
Harmony. However, it appears that I only tested it when booting using
board files, not when booting using device tree. This change fixes two
problems with regulators when booting using device tree:

1) That patch only created the vdd_sys regulator when booting using a
   board file. Since this is the root of the whole regulator tree, this
   caused no regulators to successfully initialize when booting using
   device tree. The registration of vdd_sys is moved to fix this.

2) When booting use DT, the regulator core sets has_full_constraints,
   which in turn causes the core to turn off any regulators not marked
   as always on. Some of the affected regulators are required for basic
   system operation. To solve this, add always on constraints to all
   relevant regulators. This doesn't affect booting using a board file
   since nothing sets has_full_constraints in that case.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Commit c2e935a7 "USB: move transceiver from ehci_hcd and ohci_hcd to
hcd and rename it as phy" removed the last use of the "ohci" variable
in the usb_hcd_omap_remove function, but left the variable in place
unused.

Without this patch, building omap1_defconfig results in:

In file included from drivers/usb/host/ohci-hcd.c:1013:0:
drivers/usb/host/ohci-omap.c: In function 'usb_hcd_omap_remove':
drivers/usb/host/ohci-omap.c:406:19: warning: unused variable 'ohci' [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Richard Zhao <richard.zhao@freescale.com>

In commit 4f304245 "mfd: Set asic3 DS1WM clock_rate", a possible
path through asic3_mfd_probe was introduced that would lead to
an unpredictable return value, if everything succeeds but there
are pdata->leds is NULL. This was reported correctly by gcc.

Without this patch, building magician_defconfig results in:

drivers/mfd/asic3.c: In function 'asic3_mfd_probe':
drivers/mfd/asic3.c:940:2: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>

ARM i.MX fixes for 3.6-rc

* tag 'imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
  i.MX27: Fix emma-prp and csi clocks.
  ARM: clk-imx31: Fix the keypad clock name
  ARM: dts: imx27-3ds.dts: Fix serial console node

Just a small typo fix to make lsxl dtbs compile
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Naming of emma-prp related clocks for the i.MX27 is not correct.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The Integrator timer is using the clock framework to get the
timer frequency, but missed to prepare the clock before enabling.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* 'mxs/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: always build ocotp
  ARM: mxs: Remove MMAP_MIN_ADDR setting from mxs_defconfig
  ARM: mx28: Fix registers range
  ARM: mx23: Fix registers range

* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: dts: imx: fix gpio interrupts property
  ARM: dts: imx53-ard: add regulators for lan9220
  ARM: imx: enable emi_slow_gate clock for imx5
  ARM: imx6q-sabrelite: Setup CLKO IOMUX
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

I prefer to use the Linaro mail address for the MAINTAINERS
entry due to heavy mail traffic. Take this opportunity to
update the wildcards, including removing the stmpe* drivers
from the ux500 entry since these are not specific to that
machine.

Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

With this patch ocotp support will always be build into the kernel on mxs.
Otherwise a DT-only kernel fails to link with:

arch/arm/mach-mxs/mach-mxs.c:169: undefined reference to `mxs_get_ocotp'
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The CONFIG_DEFAULT_MMAP_MIN_ADDR was set to 65536 in mxs_defconfig,
this caused severe breakage of userland applications since the upper
limit for ARM is 32768. By default CONFIG_DEFAULT_MMAP_MIN_ADDR is
set to 4096 and can also be changed via /proc/sys/vm/mmap_min_addr
if needed.

Quoting Russell King [1]:

"4096 is also fine for ARM too. There's not much point in having
defconfigs change it - that would just be pure noise in the config
files."

the CONFIG_DEFAULT_MMAP_MIN_ADDR can be removed from the defconfig
altogether.

This problem was introduced by commit cde7c41f (ARM: configs: add
defconfig for mach-mxs).

[1] http://marc.info/?l=linux-arm-kernel&m=134401593807820&w=2Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Commit 88cde8b7 (ARM: dts: imx: update #interrupt-cells for gpio nodes)
changes gpio #interrupt-cells from 1 to 2 without updating the users.
It causes the gpio irq requesting call failing in client driver's probe
function.

Add the irq type cell for those gpio interrupt users to fix their
driver probe failure.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since commit c7e963f6 (net/smsc911x: Add regulator support), the lan9220
device tree probe fails on imx53-ard board, because the commit makes
VDD33A and VDDVARIO supplies mandatory for the driver.

Add a fixed dummy 3V3 supplying lan9220 to fix the regression.

Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The imx5 common clock migration causes a regression with smsc911x
driver on imx53-ard board, where a smsc lan9220 controller gets
connected on imx53 with EIM interface.  EIM needs clock emi_slow_gate
to be functional.  In the new imx5 clock driver, there is no use count
incremented for the clock by enabling it, so the framework closes the
clock at late init time and makes EIM stop working then.

Enable emi_slow_gate in clock driver initialization to fix the
regression.

Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>

Fix the keypad clock name, in order to fix the following error:

imx-keypad imx-keypad: failed to get keypad clock
imx-keypad: probe of imx-keypad failed with error -2
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org

Fix registers range.

Cc: stable@vger.kernel.org
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Fix registers range.

Cc: stable@vger.kernel.org
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

In order to have audio functional on mx6qsabrelite, it is necessary
to setup the IOMUX for MX6Q_PAD_GPIO_0__CCM_CLKO pins as it provides
the audio clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Pull OLPC platform updates from Andres Salomon:
 "These move the OLPC Embedded Controller driver out of
  arch/x86/platform and into drivers/platform/olpc.

  OLPC machines are now ARM-based (which means lots of x86 and ARM
  changes), but are typically pretty self-contained..  so it makes more
  sense to go through a separate OLPC tree after getting the appropriate
  review/ACKs."

* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
  x86: OLPC: move s/r-related EC cmds to EC driver
  Platform: OLPC: move global variables into priv struct
  Platform: OLPC: move debugfs support from x86 EC driver
  x86: OLPC: switch over to using new EC driver on x86
  Platform: OLPC: add a suspended flag to the EC driver
  Platform: OLPC: turn EC driver into a platform_driver
  Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
  drivers: OLPC: update various drivers to include olpc-ec.h
  Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver

Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
 "This contains a set of device-tree conversions for Marvell Orion
  platforms that were staged early but took a few tries to get the
  branch into a format where it was suitable for us to pick up.

  Given that most people working on these platforms are hobbyists with
  limited time, we were a bit more flexible with merging it even though
  it came in late."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

Conflicts:
	drivers/watchdog/orion_wdt.c

Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
 "Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
  but didn't go in because the pull request ended up rejected.  So it
  just got merged, and we got this staged branch that enables the
  coupled cpuidle code on OMAP.

  With a stable git workflow from the other maintainer we could have
  staged this earlier, but that wasn't the case so we have had to merge
  it late.

  The alternative is to hold it off until 3.7 but given that the code is
  well-isolated to OMAP and they are eager to see it go in, I didn't
  push back hard in that direction."

* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP4: CPUidle: Open broadcast clock-event device.
  ARM: OMAP4: CPUidle: add synchronization for coupled idle states
  ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
  ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes for merge window fallout, and a bugfix for timer resume on
  PRIMA2."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: mmp: add missing irqs.h
  arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
  ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
  ARM: mxc: Include missing irqs.h header

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

Pull additional md update from NeilBrown:
 "This contains a few patches that depend on plugging changes in the
  block layer so needed to wait for those.

  It also contains a Kconfig fix for the new RAID10 support in dm-raid."

* tag 'md-3.6' of git://neil.brown.name/md:
  md/dm-raid: DM_RAID should select MD_RAID10
  md/raid1: submit IO from originating thread instead of md thread.
  raid5: raid5d handle stripe in batch way
  raid5: make_request use batch stripe release

Pull two ceph fixes from Sage Weil:
 "The first patch fixes up the old crufty open intent code to use the
  atomic_open stuff properly, and the second fixes a possible null deref
  and memory leak with the crypto keys."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix crypto key null deref, memory leak
  ceph: simplify+fix atomic_open

Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes a bug when the lower filesystem mount options include 'acl',
   but the eCryptfs mount options do not
 - Cleanups in the messaging code
 - Better handling of empty files in the lower filesystem to improve
   usability.  Failed file creations are now cleaned up and empty lower
   files are converted into eCryptfs during open().
 - The write-through cache changes are being reverted due to bugs that
   are not easy to fix.  Stability outweighs the performance
   enhancements here.
 - Improvement to the mount code to catch unsupported ciphers specified
   in the mount options

* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: check for eCryptfs cipher support at mount
  eCryptfs: Revert to a writethrough cache model
  eCryptfs: Initialize empty lower files when opening them
  eCryptfs: Unlink lower inode when ecryptfs_create() fails
  eCryptfs: Make all miscdev functions use daemon ptr in file private_data
  eCryptfs: Remove unused messaging declarations and function
  eCryptfs: Copy up POSIX ACL and read-only flags from lower mount