- 18 Sep, 2024 34 commits
-
-
Charlene Liu authored
[WHY & HOW] 1) We did linear/non linear transition properly long ago 2) We used that path to handle SystemDisplayEnable 3) We fixed a SystemDisplayEnable inability to fallback to passive by impacting the transition flow generically 4) AFMF later relied on the generic transition behavior Separating the two flows to make (3) non-generic is the best immediate coarse of action. DC can discern SSAMPO3 very easily from SDE. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
Chris Park <chris.park@amd.com> Signed-off-by:
Charlene Liu <Charlene.Liu@amd.com> Signed-off-by:
Alex Hung <alex.hung@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Zhikai Zhai authored
[WHY] It makes DSC enable when we commit the stream which need keep power off, and then it will skip to disable DSC if pipe reset at this situation as power has been off. It may cause the DSC unexpected enable on the pipe with the next new stream which doesn't support DSC. [HOW] Check the DSC used on current pipe status when update stream. Skip to enable if it has been off. The operation enable DSC should happen when set power on. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
Wenjing Liu <wenjing.liu@amd.com> Signed-off-by:
Zhikai Zhai <zhikai.zhai@amd.com> Signed-off-by:
-
Aurabindo Pillai authored
[WHY & HOW] When underscan is set through xrandr, it causes the stream destination rect to change in a way it becomes complicated to handle the calculations for subvp. Since this is a corner case, disable subvp when underscan is set. Fix the existing check that is supposed to catch this corner case by adding a check based on the parameters in the stream Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
Dillon Varone <dillon.varone@amd.com> Reviewed-by:
Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by:
Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by:
-
Alex Hung authored
[WHAT & HOW] req128_c is always set to false and its branch is never taken. Similarly, MacroTileSizeBytes is set to either 256 or 65535 and it is never 4096 and it's branch is not taken. Therefore, their branches are removed. This fixes 3 DEADCODE issues reported by Coverity. Acked-by:
Alvin Lee <alvin.lee2@amd.com> Reviewed-by:
-
Alex Hung authored
[WHAT & HOW] se is null checked previously in the same function, indicating it might be null; therefore, it must be checked when used again. This fixes 1 FORWARD_NULL issue reported by Coverity. Acked-by:
-
Aric Cyr authored
- Add HDMI DSC native YCbCr422 support - Add fullscreen only sharpening policy - Restructure dpia link training - Disable SYMCLK32_LE root clock gating - Clean up dsc blocks in accelerated mode - Block dynamic IPS2 on DCN35 for incompatible FW versions - Add debug options to change sharpen policies - Block timing sync for different output formats in pmo - Enable DML2 override_det_buffer_size_kbytes - Add dmub hpd sense callback - Emulate Display Hotplug Hang - Implement new DPCD register handling - Use SDR white level to calculate matrix coefficients - Round calculated vtotal Reviewed-by:
Aric Cyr <aric.cyr@amd.com> Signed-off-by:
-
Leo Ma authored
[WHY && HOW] For some HDMI OVT timing, YCbCr422 encoding fails at the DSC bandwidth check. The root cause is our DSC policy for timing doesn't account for HDMI YCbCr422 native support. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
Leo Ma <hanghong.ma@amd.com> Signed-off-by:
-
Relja Vojvodic authored
[WHAT & HOW] Disable sharpening if not in fullscreen if this policy is selected Reviewed-by:
Samson Tam <samson.tam@amd.com> Signed-off-by:
Relja Vojvodic <Relja.Vojvodic@amd.com> Signed-off-by:
-
Peichen Huang authored
[WHY] We intend to consolidate dp tunneling and conventional dp link training. [HOW] 1. Use the same link training entry for both dp and dpia 2. Move SET_CONFIG of non-transparent mode to dmub side 3. Add set_tps_notification dmub_cmd to notify tps request for non-transparent dpia link training 4. Check dpcd request result and abort link training early if dpia aux tunneling fails 5. Add option to avoid affect old product 6. Separately handle wait_time_microsec for dpia Reviewed-by:
Cruise Hung <cruise.hung@amd.com> Reviewed-by:
George Shen <george.shen@amd.com> Reviewed-by:
Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com> Signed-off-by:
Peichen Huang <PeiChen.Huang@amd.com> Signed-off-by:
-
Sung Joon Kim authored
[WHY & HOW] On display on sequence, enabling SYMCLK32_LE root clock gating causes issue in link training so disabling it is needed. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by:
Sung Joon Kim <Sungjoon.Kim@amd.com> Signed-off-by:
-
Martin Tsai authored
[WHY] DSC on eDP could be enabled during VBIOS post. The enabled DSC may not be disabled when enter to OS, once the system was in second screen only mode before entering to S4. In this case, OS will not send setTimings to reset eDP path again. The enabled DSC HW will make a new stream without DSC cannot output normally if it reused this pipe with enabled DSC. [HOW] In accelerated mode, to clean up DSC blocks if eDP is on link but not active when we are not in fast boot and seamless boot. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
Martin Tsai <martin.tsai@amd.com> Signed-off-by:
-
Nicholas Kazlauskas authored
[WHY] Hangs with Z8 can occur if running an older unfixed PMFW version. [HOW] Fallback to RCG only for dynamic IPS2 states if it's not newer than 93.12. Limit to DCN35. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
-
Samson Tam authored
[WHY] Add options to change sharpen policy based on surface format and scaling ratios. [HOW] Add sharpen_policy to change policy based on surface format and scale_to_sharpness_policy based on scaling ratios. Reviewed-by:
Jun Lei <jun.lei@amd.com> Signed-off-by:
-
Dillon Varone authored
[WHY & HOW] If the output format is different for HDMI TMDS signals, they are not synchronizable. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
-
Yihan Zhu authored
[WHY] Corrupted screen will be observed when 4k144 DP/HDMI display and 4k144 eDP are connected, changing eDP refresh rate from 60Hz to 144Hz. [HOW] override_det_buffer_size_kbytes should be true for DCN35/DCN351. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
Roman Li <roman.li@amd.com> Reviewed-by:
Yihan Zhu <Yihan.Zhu@amd.com> Signed-off-by:
-
Roman Li authored
[WHY] HPD sense notification has been implemented in DMUB, which can occur during low power states and need to be notified from firmware to driver. [HOW] Define callback and register new HPD sense notification. Reviewed-by:
-
Daniel Sa authored
[WHY] Driver reports 0 display when the virtual display is still present, and causes P-state hang in FW. [HOW] When enumerating through streams, check for active planes and use that to indicate number of displays. Reviewed-by:
Daniel Sa <Daniel.Sa@amd.com> Signed-off-by:
-
Ryan Seto authored
[WHY] There are some monitor timings that seem to be supported without DSC but actually require DSC to be displayed. A VESA SCR introduced a new max uncompressed pixel rate cap register that we can use to handle these edge cases. [HOW] SST: Read caps from link and invalidate timings that exceed the max limit but do not support DSC. Then check for options override when determining BPP. MST: Read caps from virtual DPCD peer device or daisy chained SST monitor and set validation set BPPs to max if pixel rate exceeds uncompressed limit. Validation set optimization continues as normal. Reviewed-by:
Ryan Seto <ryanseto@amd.com> Signed-off-by:
-
Samson Tam authored
[WHY] Certain profiles have higher HDR multiplier than SDR white level max which is not currently supported. [HOW] Use SDR white level when calculating matrix coefficients for HDR RGB MPO path instead of HDR multiplier. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
-
Robin Chen authored
[WHY] The calculated vtotal may has 1 line deviation. To get precisely vtotal number, round the vtotal result. Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by:
Anthony Koo <anthony.koo@amd.com> Signed-off-by:
Robin Chen <robin.chen@amd.com> Signed-off-by:
-
Le Ma authored
To be compatible with legacy IFWI, driver needs to carry legacy tOS and query pmfw version to load them accordingly. Add psp_firmware_header_v2_1 to handle the combined sos binary. Double the sos count limit for the case of aux sos fw packed. v2: pass the correct fw_bin_desc to parse_sos_bin_descriptor Signed-off-by:
Le Ma <le.ma@amd.com> Reviewed-by:
Lijo Lazar <lijo.lazar@amd.com> Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
-
Le Ma authored
Query pmfw version to determine if aux sos fw needs to be loaded in psp v13.0. v2: refine callback to check if aux_fw loading is needed instead of getting pmfw version barely v3: return the comparison directly Signed-off-by: -
Asad Kamal authored
Update PMFW interface headers for updated metrics table with gfx activity per xcd Signed-off-by:
Asad Kamal <asad.kamal@amd.com> Reviewed-by:
-
Christian König authored
This was only used as workaround for recovering the page tables after VRAM was lost and is no longer necessary after the function amdgpu_vm_bo_reset_state_machine() started to do the same. Compute never used shadows either, so the only proplematic case left is SVM and that is most likely not recoverable in any way when VRAM is lost. Signed-off-by:
Christian König <christian.koenig@amd.com> Acked-by:
-
Alex Deucher authored
Need to make sure it's halted as we don't know what state the GPU may have been left in previously. Tested-by:
Amber Lin <Amber.Lin@amd.com> Acked-by:
-
Alex Deucher authored
Need to set the pipe reset and cache invalidation bits on halt otherwise we can get stale state if the CP firmware changes (e.g., on module unload and reload). Tested-by:
-
David Belanger authored
Move enable_doorbell_selfring_aperture from common_hw_init to common_late_init in soc24, otherwise selfring aperture is initialized with an incorrect doorbell aperture base. Port changes from this commit from soc21 to soc24: commit 1c312e81 ("drm/amdgpu: Enable doorbell selfring after resize FB BAR") Signed-off-by:
David Belanger <david.belanger@amd.com> Reviewed-by:
-
Jack Xiao authored
The SET_SHADER_DEBUGGER packet must work with the added hardware queue, switch the packet submitting to mes schq pipe. Signed-off-by:
Jack Xiao <Jack.Xiao@amd.com> Acked-by:
-
Kent Russell authored
During init, there can be some collisions on the i2c bus that result in the EEPROM read failing. This has been mitigated in the PMFW to a degree, but there is still a small chance that the bus will be busy. When the read fails during RAS init, that disables page retirement altogether, which is obviously not ideal. To try to avoid that situation, set the eeprom_read function to retry once if the first read fails, specifically for smu_v13_0_6. Signed-off-by:
Kent Russell <kent.russell@amd.com> Reviewed-by:
-
Yan Zhen authored
Correctly spelled comments make it easier for the reader to understand the code. Replace 'maxium' with 'maximum' in the comment & replace 'diffculty' with 'difficulty' in the comment & replace 'suppluy' with 'supply' in the comment & replace 'Congiuration' with 'Configuration' in the comment & replace 'eanbled' with 'enabled' in the comment. Signed-off-by:
Yan Zhen <yanzhen@vivo.com> Signed-off-by:
-
Andrew Kreimer authored
Fix a typo in comments. Reported-by:
Matthew Wilcox <willy@infradead.org> Signed-off-by:
Andrew Kreimer <algonell@gmail.com> Signed-off-by:
-
Yan Zhen authored
Correctly spelled comments make it easier for the reader to understand the code. Replace 'udpate' with 'update' in the comment & replace 'recieved' with 'received' in the comment & replace 'dsiable' with 'disable' in the comment & replace 'Initiailize' with 'Initialize' in the comment & replace 'disble' with 'disable' in the comment & replace 'Disbale' with 'Disable' in the comment & replace 'enogh' with 'enough' in the comment & replace 'availabe' with 'available' in the comment. Acked-by:
-
Alex Deucher authored
Fix spelling in documentation. Reviewed-by:
-
Alex Deucher authored
Drop wrapper used in one place. gfx_v9_4_3_xcc_cp_enable() is used in one place. gfx_v9_4_3_xcc_cp_compute_enable() is used everywhere else. Reviewed-by:
-
- 17 Sep, 2024 6 commits
-
-
Bob Zhou authored
The module param pcie_p2p should be checked for kfd p2p feature, so add it. Fixes: 75f0efbc ("drm/amdgpu: Take IOMMU remapping into account for p2p checks") Signed-off-by:
Bob Zhou <bob.zhou@amd.com> Reviewed-by:
-
Tao Zhou authored
The feature is not applicable to specific app platform. v2: update the disablement condition and commit description v3: move the setting to amdgpu_ras_check_supported Signed-off-by:
Tao Zhou <tao.zhou1@amd.com> Reviewed-by:
-
Tim Huang authored
This resolves the dereference null return value warning reported by Coverity. Signed-off-by:
Tim Huang <tim.huang@amd.com> Reviewed-by:
Jesse Zhang <jesse.zhang@amd.com> Signed-off-by:
-
Jesse Zhang authored
Variable hub_inst is unused. Fixes: e28604d8 ("drm/amdkfd: Drop poison hanlding from gfx v10") Signed-off-by:
-
Kent Russell authored
We were removing the kernfs entry for queue info before checking if the queue could be destroyed. If it failed to get destroyed (e.g. during some GPU resets), then we would try to delete it later during pqm teardown, but the file was already removed. This led to a kernel WARN trying to remove size, gpuid and type. Move the remove to after the destroy check. Signed-off-by:
Jonathan Kim <jonathan.kim@amd.com> Signed-off-by:
-
Dave Airlie authored
Merge tag 'drm-xe-next-fixes-2024-09-12' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-next Driver Changes: - Fix usefafter-free when provisioning VF (Matthew Auld) - Suppress rpm warning on false positive (Rodrigo) - Fix memleak on ioctl error path (Dafna) - Fix use-after-free while inserting ggtt (Michal Wajdeczko) - Add Wa_15016589081 workaround (Tejas) - Fix error path on suspend (Maarten) Signed-off-by:
Dave Airlie <airlied@redhat.com> From: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/az6xs2z6zj3brq2h5wgaaoxwnqktrwbvxoyckrz7gbywsso734@a6v7gytqbcd6
-
