- 20 Aug, 2015 10 commits
-
-
Denis Carikli authored
commit e053f96b upstream. Since commit 3d42a379 ("can: flexcan: add 2nd clock to support imx53 and newer") the can driver requires a dt nodes to have a second clock. Add them to imx35 to fix probing the flex can driver on the respective platforms. Signed-off-by:
Denis Carikli <denis@eukrea.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Nicholas Bellinger authored
commit 007d038b upstream. This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where an explicit iser-target logout would result in ->tx_thread_active being incorrectly cleared by the logout post handler, and subsequent TX kthread leak: commit 88dcd2da Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, change iscsit_logout_post_handler_closesession() and iscsit_logout_post_handler_samecid() to only cmpxchg() on ->tx_thread_active for traditional iscsi/tcp connections. This is required because iscsi/tcp connections are invoking logout post handler logic directly from TX kthread context, while iser connections are invoking logout post handler logic from a seperate workqueue context. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit e5419865 upstream. This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where a iscsit_start_kthreads() failure triggers a NULL pointer dereference OOPs: commit 88dcd2da Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, move iscsit_start_kthreads() immediately preceeding the transmit of last login response, before signaling a successful transition into full-feature-phase within existing iscsi_target_do_tx_login_io() logic. This ensures that no target-side resource allocation failures can occur after the final login response has been successfully sent. Also, it adds a iscsi_conn->rx_login_comp to allow the RX thread to sleep to prevent other socket related failures until the final iscsi_post_login_handler() call is able to complete. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 417c20a9 upstream. This patch fixes a use-after-free bug in iscsit_release_sessions_for_tpg() where se_portal_group->session_lock was incorrectly released/re-acquired while walking the active se_portal_group->tpg_sess_list. The can result in a NULL pointer dereference when iscsit_close_session() shutdown happens in the normal path asynchronously to this code, causing a bogus dereference of an already freed list entry to occur. To address this bug, walk the session list checking for the same state as before, but move entries to a local list to avoid dropping the lock while walking the active list. As before, signal using iscsi_session->session_restatement=1 for those list entries to be released locally by iscsit_free_session() code. Reported-by:
Sunilkumar Nadumuttlu <sjn@datera.io> Cc: Sunilkumar Nadumuttlu <sjn@datera.io> Signed-off-by:
-
Axel Lin authored
commit fa8173a3 upstream. The de-emphasis sampling rate selection is controlled by BIT[3:4] of PCM1681_DEEMPH_CONTROL register. Do proper left shift to set it. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Acked-by:
Marek Belisko <marek.belisko@streamunlimited.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Roger Quadros authored
commit 9a258afa upstream. For hwmods without sysc, _init_mpu_rt_base(oh) won't be called and so _find_mpu_rt_port(oh) will return NULL thus preventing ready state check on those modules after the module is enabled. This can potentially cause a bus access error if the module is accessed before the module is ready. Fix this by unconditionally calling _init_mpu_rt_base() during hwmod _init(). Do ioremap only if we need SYSC access. Eventhough _wait_target_ready() check doesn't really need MPU RT port but just the PRCM registers, we still mandate that the hwmod must have an MPU RT port if ready state check needs to be done. Else it would mean that the module is not accessible by MPU so there is no point in waiting for target to be ready. e.g. this fixes the below DCAN bus access error on AM437x-gp-evm. [ 16.672978] ------------[ cut here ]------------ [ 16.677885] WARNING: CPU: 0 PID: 1580 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x234/0x35c() [ 16.687946] 44000000.ocp:L3 Custom Error: MASTER M2 (64-bit) TARGET L4_PER_0 (Read): Data Access in User mode during Functional access [ 16.700654] Modules linked in: xhci_hcd btwilink ti_vpfe dwc3 videobuf2_core ov2659 bluetooth v4l2_common videodev ti_am335x_adc kfifo_buf industrialio c_can_platform videobuf2_dma_contig media snd_soc_tlv320aic3x pixcir_i2c_ts c_can dc [ 16.731144] CPU: 0 PID: 1580 Comm: rpc.statd Not tainted 3.14.26-02561-gf733aa036398 #180 [ 16.739747] Backtrace: [ 16.742336] [<c0011108>] (dump_backtrace) from [<c00112a4>] (show_stack+0x18/0x1c) [ 16.750285] r6:00000093 r5:00000009 r4:eab5b8a8 r3:00000000 [ 16.756252] [<c001128c>] (show_stack) from [<c05a4418>] (dump_stack+0x20/0x28) [ 16.763870] [<c05a43f8>] (dump_stack) from [<c0037120>] (warn_slowpath_common+0x6c/0x8c) [ 16.772408] [<c00370b4>] (warn_slowpath_common) from [<c00371e4>] (warn_slowpath_fmt+0x38/0x40) [ 16.781550] r8:c05d1f90 r7:c0730844 r6:c0730448 r5:80080003 r4:ed0cd210 [ 16.788626] [<c00371b0>] (warn_slowpath_fmt) from [<c027fa94>] (l3_interrupt_handler+0x234/0x35c) [ 16.797968] r3:ed0cd480 r2:c0730508 [ 16.801747] [<c027f860>] (l3_interrupt_handler) from [<c0063758>] (handle_irq_event_percpu+0x54/0x1bc) [ 16.811533] r10:ed005600 r9:c084855b r8:0000002a r7:00000000 r6:00000000 r5:0000002a [ 16.819780] r4:ed0e6d80 [ 16.822453] [<c0063704>] (handle_irq_event_percpu) from [<c00638f0>] (handle_irq_event+0x30/0x40) [ 16.831789] r10:eb2b6938 r9:eb2b6960 r8:bf011420 r7:fa240100 r6:00000000 r5:0000002a [ 16.840052] r4:ed005600 [ 16.842744] [<c00638c0>] (handle_irq_event) from [<c00661d8>] (handle_fasteoi_irq+0x74/0x128) [ 16.851702] r4:ed005600 r3:00000000 [ 16.855479] [<c0066164>] (handle_fasteoi_irq) from [<c0063068>] (generic_handle_irq+0x28/0x38) [ 16.864523] r4:0000002a r3:c0066164 [ 16.868294] [<c0063040>] (generic_handle_irq) from [<c000ef60>] (handle_IRQ+0x38/0x8c) [ 16.876612] r4:c081c640 r3:00000202 [ 16.880380] [<c000ef28>] (handle_IRQ) from [<c00084f0>] (gic_handle_irq+0x30/0x5c) [ 16.888328] r6:eab5ba38 r5:c0804460 r4:fa24010c r3:00000100 [ 16.894303] [<c00084c0>] (gic_handle_irq) from [<c05a8d80>] (__irq_svc+0x40/0x50) [ 16.902193] Exception stack(0xeab5ba38 to 0xeab5ba80) [ 16.907499] ba20: 00000000 00000006 [ 16.916108] ba40: fa1d0000 fa1d0008 ed3d3000 eab5bab4 ed3d3460 c0842af4 bf011420 eb2b6960 [ 16.924716] ba60: eb2b6938 eab5ba8c eab5ba90 eab5ba80 bf035220 bf07702c 600f0013 ffffffff [ 16.933317] r7:eab5ba6c r6:ffffffff r5:600f0013 r4:bf07702c [ 16.939317] [<bf077000>] (c_can_plat_read_reg_aligned_to_16bit [c_can_platform]) from [<bf035220>] (c_can_get_berr_counter+0x38/0x64 [c_can]) [ 16.952696] [<bf0351e8>] (c_can_get_berr_counter [c_can]) from [<bf010294>] (can_fill_info+0x124/0x15c [can_dev]) [ 16.963480] r5:ec8c9740 r4:ed3d3000 [ 16.967253] [<bf010170>] (can_fill_info [can_dev]) from [<c0502fa8>] (rtnl_fill_ifinfo+0x58c/0x8fc) [ 16.976749] r6:ec8c9740 r5:ed3d3000 r4:eb2b6780 [ 16.981613] [<c0502a1c>] (rtnl_fill_ifinfo) from [<c0503408>] (rtnl_dump_ifinfo+0xf0/0x1dc) [ 16.990401] r10:ec8c9740 r9:00000000 r8:00000000 r7:00000000 r6:ebd4d1b4 r5:ed3d3000 [ 16.998671] r4:00000000 [ 17.001342] [<c0503318>] (rtnl_dump_ifinfo) from [<c050e6e4>] (netlink_dump+0xa8/0x1e0) [ 17.009772] r10:00000000 r9:00000000 r8:c0503318 r7:ebf3e6c0 r6:ebd4d1b4 r5:ec8c9740 [ 17.018050] r4:ebd4d000 [ 17.020714] [<c050e63c>] (netlink_dump) from [<c050ec10>] (__netlink_dump_start+0x104/0x154) [ 17.029591] r6:eab5bd34 r5:ec8c9980 r4:ebd4d000 [ 17.034454] [<c050eb0c>] (__netlink_dump_start) from [<c0505604>] (rtnetlink_rcv_msg+0x110/0x1f4) [ 17.043778] r7:00000000 r6:ec8c9980 r5:00000f40 r4:ebf3e6c0 [ 17.049743] [<c05054f4>] (rtnetlink_rcv_msg) from [<c05108e8>] (netlink_rcv_skb+0xb4/0xc8) [ 17.058449] r8:eab5bdac r7:ec8c9980 r6:c05054f4 r5:ec8c9980 r4:ebf3e6c0 [ 17.065534] [<c0510834>] (netlink_rcv_skb) from [<c0504134>] (rtnetlink_rcv+0x24/0x2c) [ 17.073854] r6:ebd4d000 r5:00000014 r4:ec8c9980 r3:c0504110 [ 17.079846] [<c0504110>] (rtnetlink_rcv) from [<c05102ac>] (netlink_unicast+0x180/0x1ec) [ 17.088363] r4:ed0c6800 r3:c0504110 [ 17.092113] [<c051012c>] (netlink_unicast) from [<c0510670>] (netlink_sendmsg+0x2ac/0x380) [ 17.100813] r10:00000000 r8:00000008 r7:ec8c9980 r6:ebd4d000 r5:eab5be70 r4:eab5bee4 [ 17.109083] [<c05103c4>] (netlink_sendmsg) from [<c04dfdb4>] (sock_sendmsg+0x90/0xb0) [ 17.117305] r10:00000000 r9:eab5a000 r8:becdda3c r7:0000000c r6:ea978400 r5:eab5be70 [ 17.125563] r4:c05103c4 [ 17.128225] [<c04dfd24>] (sock_sendmsg) from [<c04e1c28>] (SyS_sendto+0xb8/0xdc) [ 17.136001] r6:becdda5c r5:00000014 r4:ecd37040 [ 17.140876] [<c04e1b70>] (SyS_sendto) from [<c000e680>] (ret_fast_syscall+0x0/0x30) [ 17.148923] r10:00000000 r8:c000e804 r7:00000122 r6:becdda5c r5:0000000c r4:becdda5c [ 17.157169] ---[ end trace 2b71e15b38f58bad ]--- Fixes: 6423d6df ("ARM: OMAP2+: hwmod: check for module address space during init") Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Paul Walmsley <paul@pwsan.com> Signed-off-by:
-
Eric W. Biederman authored
commit f9bb4882 upstream. This allows for better documentation in the code and it allows for a simpler and fully correct version of fs_fully_visible to be written. The mount points converted and their filesystems are: /sys/hypervisor/s390/ s390_hypfs /sys/kernel/config/ configfs /sys/kernel/debug/ debugfs /sys/firmware/efi/efivars/ efivarfs /sys/fs/fuse/connections/ fusectl /sys/fs/pstore/ pstore /sys/kernel/tracing/ tracefs /sys/fs/cgroup/ cgroup /sys/kernel/security/ securityfs /sys/fs/selinux/ selinuxfs /sys/fs/smackfs/ smackfs Acked-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Signed-off-by:
-
David S. Miller authored
commit 44922150 upstream. If we have a series of events from userpsace, with %fprs=FPRS_FEF, like follows: ETRAP ETRAP VIS_ENTRY(fprs=0x4) VIS_EXIT RTRAP (kernel FPU restore with fpu_saved=0x4) RTRAP We will not restore the user registers that were clobbered by the FPU using kernel code in the inner-most trap. Traps allocate FPU save slots in the thread struct, and FPU using sequences save the "dirty" FPU registers only. This works at the initial trap level because all of the registers get recorded into the top-level FPU save area, and we'll return to userspace with the FPU disabled so that any FPU use by the user will take an FPU disabled trap wherein we'll load the registers back up properly. But this is not how trap returns from kernel to kernel operate. The simplest fix for this bug is to always save all FPU register state for anything other than the top-most FPU save area. Getting rid of the optimized inner-slot FPU saving code ends up making VISEntryHalf degenerate into plain VISEntry. Longer term we need to do something smarter to reinstate the partial save optimizations. Perhaps the fundament error is having trap entry and exit allocate FPU save slots and restore register state. Instead, the VISEntry et al. calls should be doing that work. This bug is about two decades old. Reported-by:
James Y Knight <jyknight@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Benjamin Randazzo authored
commit b6878d9e upstream. In drivers/md/md.c get_bitmap_file() uses kmalloc() for creating a mdu_bitmap_file_t called "file". 5769 file = kmalloc(sizeof(*file), GFP_NOIO); 5770 if (!file) 5771 return -ENOMEM; This structure is copied to user space at the end of the function. 5786 if (err == 0 && 5787 copy_to_user(arg, file, sizeof(*file))) 5788 err = -EFAULT But if bitmap is disabled only the first byte of "file" is initialized with zero, so it's possible to read some bytes (up to 4095) of kernel space memory from user space. This is an information leak. 5775 /* bitmap disabled, zero the first byte and copy out */ 5776 if (!mddev->bitmap_info.file) 5777 file->pathname[0] = '\0'; Signed-off-by:
Benjamin Randazzo <benjamin@randazzo.fr> Signed-off-by:
NeilBrown <neilb@suse.com> Cc: Moritz Mühlenhoff <jmm@inutil.org> Signed-off-by:
-
Luis Henriques authored
Signed-off-by:
-
- 12 Aug, 2015 14 commits
-
-
Firo Yang authored
commit 4e023612 upstream. Warning like this: drivers/md/md.c: In function "update_array_info": drivers/md/md.c:6394:26: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses] !mddev->persistent != info->not_persistent|| Fix it as Neil Brown said: mddev->persistent != !info->not_persistent || Signed-off-by:
Firo Yang <firogm@gmail.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Alessio Igor Bogani authored
commit 304f0a98 upstream. The commit 0718e59a ("mmc: sdhci: move FSL ESDHC reset handling quirk into esdhc code") states that Freescale esdhc is the only controller which needs the interrupt registers restored after a reset. So it moves SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET quirk handling code into the esdhc-imx driver only. Unfortunately the same controller is used in other boards which use the of-esdhc driver instead (like powerpc P2020). Restore interrupts after reset in the sdhci-of-esdhc driver also. Signed-off-by:
Alessio Igor Bogani <alessio.bogani@elettra.eu> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Cc: Jakub Kicinski <kubakici@wp.pl> Signed-off-by:
-
Heiko Carstens authored
commit e47994dd upstream. The sfpc inline assembly within execve_tail() may incorrectly set bits 28-31 of the sfpc instruction to a value which is not zero. These bits however are currently unused and therefore should be zero so we won't get surprised if these bits will be used in the future. Therefore remove the second operand from the inline assembly. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
Martin Schwidefsky authored
commit f9c87a6f upstream. If the kernel is compiled with gcc 5.1 and the XZ compression option the decompress_kernel function calls _sclp_print_early in 64-bit mode while the content of the upper register half of %r6 is non-zero. This causes a specification exception on the servc instruction in _sclp_servc. The _sclp_print_early function saves and restores the upper registers halves but it fails to clear them for the 31-bit code of the mini sclp driver. Signed-off-by:
-
Al Viro authored
commit 75a6f82a upstream. Normally opening a file, unlinking it and then closing will have the inode freed upon close() (provided that it's not otherwise busy and has no remaining links, of course). However, there's one case where that does *not* happen. Namely, if you open it by fhandle with cold dcache, then unlink() and close(). In normal case you get d_delete() in unlink(2) notice that dentry is busy and unhash it; on the final dput() it will be forcibly evicted from dcache, triggering iput() and inode removal. In this case, though, we end up with *two* dentries - disconnected (created by open-by-fhandle) and regular one (used by unlink()). The latter will have its reference to inode dropped just fine, but the former will not - it's considered hashed (it is on the ->s_anon list), so it will stay around until the memory pressure will finally do it in. As the result, we have the final iput() delayed indefinitely. It's trivial to reproduce - void flush_dcache(void) { system("mount -o remount,rw /"); } static char buf[20 * 1024 * 1024]; main() { int fd; union { struct file_handle f; char buf[MAX_HANDLE_SZ]; } x; int m; x.f.handle_bytes = sizeof(x); chdir("/root"); mkdir("foo", 0700); fd = open("foo/bar", O_CREAT | O_RDWR, 0600); close(fd); name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0); flush_dcache(); fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR); unlink("foo/bar"); write(fd, buf, sizeof(buf)); system("df ."); /* 20Mb eaten */ close(fd); system("df ."); /* should've freed those 20Mb */ flush_dcache(); system("df ."); /* should be the same as #2 */ } will spit out something like Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 303843 1131 100% / Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 303843 1131 100% / Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 283282 21692 93% / - inode gets freed only when dentry is finally evicted (here we trigger than by remount; normally it would've happened in response to memory pressure hell knows when). Acked-by:
J. Bruce Fields <bfields@fieldses.org> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> [ kamal: backport to 3.19-stable: no fast_dput() ] Signed-off-by:
-
Jingju Hou authored
commit 9cd76049 upstream. pdev->dev.platform_data is not initialized if match is true in function sdhci_pxav3_probe. Just local variable pdata is assigned the return value from function pxav3_get_mmc_pdata(). static int sdhci_pxav3_probe(struct platform_device *pdev) { struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; ... if (match) { ret = mmc_of_parse(host->mmc); if (ret) goto err_of_parse; sdhci_get_of_property(pdev); pdata = pxav3_get_mmc_pdata(dev); } ... } Signed-off-by:
Jingju Hou <houjingj@marvell.com> Fixes: b650352d("mmc: sdhci-pxa: Add device tree support") Signed-off-by:
-
Joakim Tjernlund authored
commit 8e91125f upstream. Support for 8BIT bus with was added some time ago to sdhci-esdhc but then missed to remove the 8BIT from the reserved bit mask which made 8BIT non functional. Fixes: 66b50a00 ("mmc: esdhc: Add support for 8-bit bus width and..") Signed-off-by:
Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by:
-
Tomas Winkler authored
commit 9098f84c upstream. Enclosing mmc_blk_put() is missing in power_ro_lock_show() sysfs handler, let's add it. Fixes: add710ea ("mmc: boot partition ro lock support") Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Edward Hyunkoo Jee authored
commit 0848f642 upstream. When ip_frag_queue() computes positions, it assumes that the passed sk_buff does not contain L2 headers. However, when PACKET_FANOUT_FLAG_DEFRAG is used, IP reassembly functions can be called on outgoing packets that contain L2 headers. Also, IPv4 checksum is not corrected after reassembly. Fixes: 7736d33f ("packet: Add pre-defragmentation support for ipv4 fanouts.") Signed-off-by:
Edward Hyunkoo Jee <edjee@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Jerry Chu <hkchu@google.com> Signed-off-by:
-
Nikolay Aleksandrov authored
commit 7d5cd2ce upstream. If the bond is enslaving a device with different type it will be setup by it, but if after being setup the enslave fails the bond doesn't switch back its type and also keeps pointers to foreign structures that can be long gone. Thus revert back any type changes if the enslave failed and the bond had to change its type. Example: Before patch: $ echo lo > bond0/bonding/slaves -bash: echo: write error: Cannot assign requested address $ ip l sh bond0 20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN mode DEFAULT group default link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00 $ echo +eth1 > bond0/bonding/slaves $ ip l sh bond0 20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff (notice the MASTER flag is gone) After patch: $ echo lo > bond0/bonding/slaves -bash: echo: write error: Cannot assign requested address $ ip l sh bond0 21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff $ echo +eth1 > bond0/bonding/slaves $ ip l sh bond0 21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: e36b9d16 ("bonding: clean muticast addresses when device changes type") Signed-off-by:
-
Nikolay Aleksandrov authored
commit 06f6d109 upstream. When the bonding is being unloaded and the netdevice notifier is unregistered it executes NETDEV_UNREGISTER for each device which should remove the bond's proc entry but if the device enslaved is not of ARPHRD_ETHER type and is in front of the bonding, it may execute bond_release_and_destroy() first which would release the last slave and destroy the bond device leaving the proc entry and thus we will get the following error (with dynamic debug on for bond_netdev_event to see the events order): [ 908.963051] eql: event: 9 [ 908.963052] eql: IFF_SLAVE [ 908.963054] eql: event: 2 [ 908.963056] eql: IFF_SLAVE [ 908.963058] eql: event: 6 [ 908.963059] eql: IFF_SLAVE [ 908.963110] bond0: Releasing active interface eql [ 908.976168] bond0: Destroying bond bond0 [ 908.976266] bond0 (unregistering): Released all slaves [ 908.984097] ------------[ cut here ]------------ [ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575 remove_proc_entry+0x112/0x160() [ 908.984110] remove_proc_entry: removing non-empty directory 'net/bonding', leaking at least 'bond0' [ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore usb_common [last unloaded: bonding] [ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O 4.2.0-rc2+ #8 [ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34 ffff8800358dfda8 [ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40 ffff88003e3a4280 [ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a ffffffff8172ebd0 [ 908.984181] Call Trace: [ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50 [ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0 [ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50 [ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160 [ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30 [bonding] [ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding] [ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70 [ 908.984225] [<ffffffff8142f52d>] ? unregister_pernet_operations+0x8d/0xd0 [ 908.984228] [<ffffffff8142f58d>] ? unregister_pernet_subsys+0x1d/0x30 [ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding] [ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250 [ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0 [ 908.984244] [<ffffffff8152b732>] ? entry_SYSCALL_64_fastpath+0x16/0x75 [ 908.984247] ---[ end trace 7c006ed4abbef24b ]--- Thus remove the proc entry manually if bond_release_and_destroy() is used. Because of the checks in bond_remove_proc_entry() it's not a problem for a bond device to change namespaces (the bug fixed by the Fixes commit) but since commit f9399814 ("bonding: Don't allow bond devices to change network namespaces.") that can't happen anyway. Reported-by:
Carol Soto <clsoto@linux.vnet.ibm.com> Signed-off-by:
-
Alexey Khoroshilov authored
commit 53e20f2e upstream. There was an omission in transition to devm_xxx resource handling. iounmap(udc->phy_regs) were removed, but ioremap() was left without devm_. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Fixes: 3517c31a ("usb: gadget: mv_udc: use devm_xxx for probe") Signed-off-by:
Felipe Balbi <balbi@ti.com> [ luis: backported to 3.16: - file rename: drivers/usb/gadget/udc/mv_udc_core.c -> drivers/usb/gadget/mv_udc_core.c ] Signed-off-by:
-
Tilman Schmidt authored
commit fd98e941 upstream. Commit 79901317 ("n_tty: Don't flush buffer when closing ldisc"), first merged in kernel release 3.10, caused the following regression in the Gigaset M101 driver: Before that commit, when closing the N_TTY line discipline in preparation to switching to N_GIGASET_M101, receive_room would be reset to a non-zero value by the call to n_tty_flush_buffer() in n_tty's close method. With the removal of that call, receive_room might be left at zero, blocking data reception on the serial line. The present patch fixes that regression by setting receive_room to an appropriate value in the ldisc open method. Fixes: 79901317 ("n_tty: Don't flush buffer when closing ldisc") Signed-off-by:
Tilman Schmidt <tilman@imap.cc> Signed-off-by:
-
Nikolay Aleksandrov authored
commit 5ebc7846 upstream. Since the mdb add/del code was introduced there have been 2 br_mdb_notify calls when doing br_mdb_add() resulting in 2 notifications on each add. Example: Command: bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent Before patch: root@debian:~# bridge monitor all [MDB]dev br0 port eth1 grp 239.0.0.1 permanent [MDB]dev br0 port eth1 grp 239.0.0.1 permanent After patch: root@debian:~# bridge monitor all [MDB]dev br0 port eth1 grp 239.0.0.1 permanent Signed-off-by:
-
- 11 Aug, 2015 16 commits
-
-
Dan Carpenter authored
commit 50c2e4dd upstream. The > should be >=. I also added spaces around the '-' operations so the code is a little more consistent and matches the condition better. Fixes: f53c3fe8 ('xen-netback: Introduce TX grant mapping') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Scott Wood authored
commit 5f867db6 upstream. Commit 66507c7b ("mtd: nand: Add support to use nand_base poi databuf as bounce buffer") added a flag NAND_USE_BOUNCE_BUFFER using the same bit value as the existing NAND_BUSWIDTH_AUTO. Cc: Kamal Dasu <kdasu.kdev@gmail.com> Fixes: 66507c7b ("mtd: nand: Add support to use nand_base poi databuf as bounce buffer") Signed-off-by:
Scott Wood <scottwood@freescale.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Kishon Vijay Abraham I authored
commit 408806f7 upstream. DTO/DCRC errors were not being informed to the mmc core since commit ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC errors. This is because after this commit 'host->data' is checked after it has been cleared to NULL by omap_hsmmc_dma_cleanup(). Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked making core layer not to be aware of DTO/DCRC errors. Because of this any command invoked after DTO/DCRC error leads to a hang. Fix this by checking for 'host->data' before it is actually cleared. Fixes: ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQ") Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Vignesh R <vigneshr@ti.com> Tested-by:
Andreas Fenkart <afenkart@gmail.com> Signed-off-by:
-
NeilBrown authored
commit 34cab6f4 upstream. When we get a read error from the last working device, we don't try to repair it, and don't fail the device. We simple report a read error to the caller. However the current test for 'is this the last working device' is wrong. When there is only one fully working device, it assumes that a non-faulty device is that device. However a spare which is rebuilding would be non-faulty but so not the only working device. So change the test from "!Faulty" to "In_sync". If ->degraded says there is only one fully working device and this device is in_sync, this must be the one. This bug has existed since we allowed read_balance to read from a recovering spare in v3.0 Reported-and-tested-by:
Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054 ("md/raid1: clean up read_balance.") Signed-off-by:
-
Martin K. Petersen authored
commit f3f5da62 upstream. This fixes a data corruption bug when using discard on top of MD linear, raid0 and raid10 personalities. Commit 20d0189b "block: Introduce new bio_split()" permits sharing the bio_vec between the two resulting bios. That is fine for read/write requests where the bio_vec is immutable. For discards, however, we need to be able to attach a payload and update the bio_vec so the page can get mapped to a scatterlist entry. Therefore the bio_vec can not be shared when splitting discards and we must do a full clone. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Reported-by:
Seunguk Shin <seunguk.shin@samsung.com> Tested-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Bernhard Bender authored
commit 96849170 upstream. This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30 touch screen. Due to a missing delay between the RESET and SET_RATE commands, the touch screen may become unresponsive during system startup or driver loading. According to the DMC documentation, a delay is needed after the RESET command to allow the chip to complete its internal initialization. As this delay is not guaranteed, we had a system where the touch screen occasionally did not send any touch data. There was no other indication of the problem. The patch fixes the problem by adding a 150ms delay between the RESET and SET_RATE commands. Suggested-by:
Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by:
Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Chris Metcalf authored
commit 3f81d244 upstream. We were previously using free_bootmem() and just getting lucky that nothing too bad happened. Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by:
-
Tejun Heo authored
commit 5f6c2d2b upstream. When a blkcg configuration is targeted to a partition rather than a whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it forgets to put the gendisk ref in that case. Fix it. Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Oliver Neukum authored
commit 5fb2c782 upstream. This device automatically switches itself to another mode (0x1405) unless the specific access pattern of Windows is followed in its initial mode. That makes a dirty unmount of the internal storage devices inevitable if they are mounted. So the card reader of such a device should be ignored, lest an unclean removal become inevitable. This replaces an earlier patch that ignored all LUNs of this device. That patch was overly broad. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Reviewed-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
-
Alan Stern authored
commit 7d8021c9 upstream. This patch fixes a bug introduced by commit 977dcfdc ("USB: OHCI: don't lose track of EDs when a controller dies"). The commit changed ed_state from ED_UNLINK to ED_IDLE too early, before finish_urb() had been called. The user-visible consequence is that the driver occasionally crashes or locks up when an URB is submitted while another URB for the same endpoint is being unlinked. This patch moves the ED state change later, to the right place. The drawback is that now we may unnecessarily execute some instructions multiple times when a controller dies. Since controllers dying is an exceptional occurrence, a little wasted time won't matter. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Heiko Przybyl <lil_tux@web.de> Tested-by:
-
Lu Baolu authored
commit 2d2a3167 upstream. Commit 25cd2882 ("usb/xhci: Change how we indicate a host supports Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed root hub. The intention of that change was to avoid touching usb core internal field, a.k.a. lpm_capable, and let usb core to set it by checking U1 and U2 exit latency values in the descriptor. Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately, root hub is a special usb device as it has no parent. Hub_port_init() will never be called for a root hub device. That means lpm_capable will by no means be set for the root hub. As the result, lpm isn't functional at all in Linux kernel. This patch add the code to check and set lpm_capable when registering a root hub device. It could be back-ported to kernels as old as v3.15, that contains the Commit 25cd2882 ("usb/xhci: Change how we indicate a host supports Link PM."). Reported-by:
Kevin Strasser <kevin.strasser@linux.intel.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Acked-by:
-
Zhuang Jin Can authored
commit aca3a048 upstream. Port link change with port in resume state should not be reported to usbcore, as this is an internal state to be handled by xhci driver. Reporting PLC to usbcore may cause usbcore clearing PLC first and port change event irq won't be generated. Signed-off-by:
Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Zhuang Jin Can authored
commit fac4271d upstream. When the link is just waken, it's in Resume state, and driver sets PLS to U0. This refers to Phase 1. Phase 2 refers to when the link has completed the transition from Resume state to U0. With the fix of xhci: report U3 when link is in resume state, it also exposes an issue that usb3 roothub and controller can suspend right after phase 1, and this causes a hard hang in controller. To fix the issue, we need to prevent usb3 bus suspend if any port is resuming in phase 1. [merge separate USB2 and USB3 port resume checking to one -Mathias] Signed-off-by:
-
Zhuang Jin Can authored
commit 243292a2 upstream. xhci_hub_report_usb3_link_state() returns pls as U0 when the link is in resume state, and this causes usb core to think the link is in U0 while actually it's in resume state. When usb core transfers control request on the link, it fails with TRB error as the link is not ready for transfer. To fix the issue, report U3 when the link is in resume state, thus usb core knows the link it's not ready for transfer. Signed-off-by:
-
Brian Campbell authored
commit 326124a0 upstream. When resetting a device the number of active TTs may need to be corrected by xhci_update_tt_active_eps, but the number of old active endpoints supplied to it was always zero, so the number of TTs and the bandwidth reserved for them was not updated, and could rise unnecessarily. This affected systems using Intel's Patherpoint chipset, which rely on software bandwidth checking. For example, a Lenovo X230 would lose the ability to use ports on the docking station after enough suspend/resume cycles because the bandwidth calculated would rise with every cycle when a suitable device is attached. The correct number of active endpoints is calculated in the same way as in xhci_reserve_bandwidth. Signed-off-by:
Brian Campbell <bacam@z273.org.uk> Signed-off-by:
-
AMAN DEEP authored
commit 34968106 upstream. virt_dev->num_cached_rings counts on freed ring and is not updated correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring is added into cache and then num_rings_cache is incremented as below: virt_dev->ring_cache[rings_cached] = virt_dev->eps[ep_index].ring; virt_dev->num_rings_cached++; here, free ring pointer is added to a current index and then index is incremented. So current index always points to empty location in the ring cache. For getting available free ring, current index should be decremented first and then corresponding ring buffer value should be taken from ring cache. But In function xhci_endpoint_init(), the num_rings_cached index is accessed before decrement. virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; virt_dev->num_rings_cached--; This is bug in manipulating the index of ring cache. And it should be as below: virt_dev->num_rings_cached--; virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; Signed-off-by:
Aman Deep <aman.deep@samsung.com> Signed-off-by:
-
