- 21 Sep, 2022 34 commits
-
-
Eddie James authored
Move the startup procedure into a function, and correct a missing check on the return code for writing the PRS_CFG register. Cc: <stable@vger.kernel.org> Signed-off-by:
Eddie James <eajames@linux.ibm.com> Reviewed-by:
Joel Stanley <joel@jms.id.au> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220915195719.136812-2-eajames@linux.ibm.comSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Nuno Sá authored
Document the new property to enable doubling the analog input range. Signed-off-by:
Nuno Sá <nuno.sa@analog.com> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220912081223.173584-4-nuno.sa@analog.comSigned-off-by:
-
Nuno Sá authored
By default the driver was always setting the RANGE bit which means that the analog input goes from 0 to VREF. However, we might want to have 0 to 2xVREF. This change adds a new Firmware property to allow for the extended range while keeping the default behavior if nothing is provided. Signed-off-by:
-
Nuno Sá authored
Some of the supported devices have 4 or 2 LSB trailing bits that should not be taken into account. Hence we need to shift these bits out which fits perfectly on the scan type shift property. This change fixes both raw and buffered reads. Fixes: f2f7a449 ("iio:adc:ad7923: Add support for the ad7904/ad7914/ad7924") Fixes: 851644a6 ("iio: adc: ad7923: Add support for the ad7908/ad7918/ad7928") Signed-off-by:
-
Olivier Moysan authored
Add support of identification registers to STM32 ADC. By default the ADC hardware instance number is retrieved from the compatible configuration data. Get the available ADC number per ADC block, from hardware configuration register, when this register exists. Signed-off-by:
Olivier Moysan <olivier.moysan@foss.st.com> Reviewed-by:
Fabrice Gasnier <fabrice.gasnier@foss.st.com> Link: https://lore.kernel.org/r/20220915135452.1712453-1-olivier.moysan@foss.st.comSigned-off-by:
-
Lorenzo Bianconi authored
Add device bindings for lsm6dstx IMU sensor. Use lsm6dst as fallback device for lsm6dstx since it implements all the features currently supported by lsm6dstx. Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/dadc2acf88b0b73feac9a8980ad9af1658297bc1.1663262890.git.lorenzo@kernel.orgSigned-off-by:
-
Lorenzo Bianconi authored
Add support to STM LSM6DSTX (acc + gyro) Mems sensor. The LSM6DSTX sensor can use LSM6DST as fallback device since it implements all the LSM6DSTX features currently implemented in st_lsm6dsx. Datasheet: https://www.st.com/resource/en/datasheet/lsm6dstx.pdfSigned-off-by:
-
Ciprian Regus authored
Set the iio device's name based on the chip used for the LTC2499 only. The most common way for IIO clients to interact with a device is to address it based on it's name. By using the dev_name() function, the name will be set based on a i2c_client's kobj name, which has the format i2c_instance-i2c_address (1-0076 for example). This is not ideal, since it makes a requirement for userspace to have knowledge about the hardware connections of the device. The name field is set to NULL for the LTC2497 and LTC2496, so that the old name can kept as it is, since changing it will result in an ABI breakage. Signed-off-by:
Ciprian Regus <ciprian.regus@analog.com> Link: https://lore.kernel.org/r/20220916140922.2506248-6-ciprian.regus@analog.comSigned-off-by:
-
Ciprian Regus authored
The LTC2499 is a 16-channel (eight differential), 24-bit, ADC with Easy Drive technology and a 2-wire, I2C interface. Implement support for the LTC2499 ADC by extending the LTC2497 driver. A new chip_info struct is added to differentiate between chip types and resolutions when reading data from the device. Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/2499fe.pdfSigned-off-by:
-
Ciprian Regus authored
Update the MAINTAINERS file to include the path for the LTC2497 and LTC2496 devicetree bindings documentation. Signed-off-by:
-
Ciprian Regus authored
Update the bindings documentation for ltc2497 to include the ltc2499. Signed-off-by:
-
Ciprian Regus authored
Remove the specific entry for ad5758, since Documentation/devicetree/bindings/iio/*/adi,* already matches the path. Signed-off-by:
-
Uwe Kleine-König authored
After the result of the previous conversion is read the chip automatically starts a new conversion and doesn't accept new i2c transfers until this conversion is completed which makes the function return failure. So add an early return iff the programming of the new address isn't needed. Note this will not fix the problem in general, but all cases that are currently used. Once this changes we get the failure back, but this can be addressed when the need arises. Fixes: 69548b7c ("iio: adc: ltc2497: split protocol independent part in a separate module ") Reported-by:
Meng Li <Meng.Li@windriver.com> Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by:
Denys Zagorui <dzagorui@cisco.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220815091647.1523532-1-dzagorui@cisco.comSigned-off-by:
-
Angel Iglesias authored
Allows sampling frequency and IIR filter coefficients configuration using sysfs ABI. The IIR filter coefficient is configurable using the sysfs attribute "filter_low_pass_3db_frequency". Signed-off-by:
Angel Iglesias <ang.iglesiasg@gmail.com> Link: https://lore.kernel.org/r/876f8a2277f71672488e99aa02aae4239d530f51.1663025017.git.ang.iglesiasg@gmail.comSigned-off-by:
-
Angel Iglesias authored
Add bosch,bmp380 compatible string for the new family of sensors. This family includes the BMP380, BMP384 and BMP388. The register map in this family changes substantially and introduces new features but core concepts and operations carryover from the previous iterations Signed-off-by:
-
Angel Iglesias authored
Adds compatibility with the new generation of this sensor, the BMP380. Includes basic sensor initialization to do pressure and temp measurements and allows tuning oversampling settings for each channel. The compensation algorithms are adapted from the device datasheet and the repository https://github.com/BoschSensortec/BMP3-Sensor-API. Signed-off-by:
-
Angel Iglesias authored
Change device tables declarations to forward order like in SPI codepath. Suggested-by:
-
Angel Iglesias authored
Adds DMA-safe buffers to driver data struct to store raw data from sensors The multiple buffers used thorough the driver share the same memory allocated as part of the device data instance. The union containing the buffers is aligned to allow safe usage with DMA operations, such as regmap bulk read calls. Updated measurement and calibration reading functions to use the safe DMA buffers. Suggested-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Angel Iglesias authored
Simplified common initialization logic of different sensor types unifying calibration and initial configuration recovery. Default config param values of each sensor type are stored inside chip_info structure and used to initialize sensor data struct instance. The helper functions for read each sensor type calibration are converted to a callback available on the chip_info struct. Separated bme280 specific calibration code from bmp280 function. Dropped the additional chip_id argument in bmp280 code as is not longer required. Now both bmp280/bme280 calibration function use same signature as bmp180. Suggested-by:
-
Angel Iglesias authored
On bmp280 and bme280, the temperature and pressure calibration parameters are available on a contiguous memory region. Considering this arrangement, simplified the calibration reading function by using only one buffer to read in batch temperature and pressure registers. Signed-off-by:
-
Angel Iglesias authored
Cleaned and simplified register values construction and extraction converting to use FIELD_PREP and FIELD_GET macros. Replaced hardcoded bit masks with GENMASK macro. Signed-off-by:
-
Angel Iglesias authored
Reordered definitions of local variables following the reverse christmas tree convention. Suggested-by:
-
Nuno Sá authored
Make sure that the needed i2c functionality is supported during probe. Signed-off-by:
Michael Hennerich <michael.hennerich@analog.com> Link: https://lore.kernel.org/r/20220913073413.140475-3-nuno.sa@analog.comSigned-off-by:
-
Michael Hennerich authored
For reliable operation across the full range of supported interface rates, the AD5593R needs a STOP condition between address write, and data read (like show in the datasheet Figure 40) so in turn i2c_smbus_read_word_swapped cannot be used. While at it, a simple helper was added to make the code simpler. Fixes: 56ca9db8 ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs") Signed-off-by:
-
Crt Mori authored
Change/refactor to the new way of defining available attribute values. Signed-off-by:
Crt Mori <cmo@melexis.com> Link: https://lore.kernel.org/r/20220906112632.244453-1-cmo@melexis.comSigned-off-by:
-
George Mois authored
ADXL312 and ADXL314 are small, thin, low power, 3-axis accelerometers with high resolution (13-bit) measurement up to +/-12 g and +/- 200 g respectively. Implement support for ADXL312 and ADXL314 by extending the ADXL313 driver. Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADXL312.pdf Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADXL314.pdfSigned-off-by:
George Mois <george.mois@analog.com> Link: https://lore.kernel.org/r/20220905132018.364900-2-george.mois@analog.comSigned-off-by:
-
George Mois authored
Extend the adi,adxl313.yaml file with information regrding the ADXL312 and ADXL314 devices. Signed-off-by:
-
Angel Iglesias authored
Updated links for BMP280 and BME280 datasheets on Bosch website. Datasheet of BMP180 is no longer available on the manufacturer's website, changed the link to a copy hosted by a third party. Reported-by:
-
Martyn Welch authored
Add support for ST LPS22DF pressure sensor. Datasheet: https://www.st.com/resource/en/datasheet/lps22df.pdfSigned-off-by:
Martyn Welch <martyn.welch@collabora.co.uk> Link: https://lore.kernel.org/r/20220909161611.780720-2-martyn.welch@collabora.co.ukSigned-off-by:
-
Martyn Welch authored
Add support for the ST LPS22DF, an I2C/SPI pressure sensor. Signed-off-by:
-
Greg Kroah-Hartman authored
Merge tag 'coresight-next-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux into char-misc-next Suzuki writes: "coresight: Changes for v6.1 Coresight trace subsystem updates for v6.1 includes: - Support for HiSilicon PTT trace - Coresight cleanup of sysfs accessor functions, reduced code size. - Expose coresight timestamp source for ETMv4+ - DT binding updates to include missing properties - Minor documentation, Kconfig text fixes. Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>" * tag 'coresight-next-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux: hwtracing: hisi_ptt: Fix up for "iommu/dma: Make header private" MAINTAINERS: Add maintainer for HiSilicon PTT driver docs: trace: Add HiSilicon PTT device driver documentation hwtracing: hisi_ptt: Add tune function support for HiSilicon PCIe Tune and Trace device hwtracing: hisi_ptt: Add trace function support for HiSilicon PCIe Tune and Trace device iommu/arm-smmu-v3: Make default domain type of HiSilicon PTT device to identity coresight: cti-sysfs: Mark coresight_cti_reg_store() as __maybe_unused coresight: Make new csdev_access offsets unsigned coresight: cti-sysfs: Re-use same functions for similar sysfs register accessors coresight: Re-use same function for similar sysfs register accessors coresight: Simplify sysfs accessors by using csdev_access abstraction coresight: Remove unused function parameter coresight: etm4x: docs: Add documentation for 'ts_source' sysfs interface coresight: etm4x: Expose default timestamp source in sysfs dt-bindings: arm: coresight-tmc: Add 'iommu' property dt-bindings: arm: coresight: Add 'power-domains' property coresight: docs: Fix a broken reference coresight: trbe: fix Kconfig "its" grammar
-
Greg Kroah-Hartman authored
Merge tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next Jonathan writes: 1st set of IIO new device support, features and cleanup for 6.1 This includes Nuno Sa's work to move the IIO core over to generic firmware properties rather than having DT specific code paths. Combined with Andy Shevchenko's long term work on drivers, this leaves IIO in a good state for handling other firmware types. New device support - liteon,ltrf216a * New driver and dt bindings to support this Light sensor. - maxim,max11205 * New driver for this 16bit single channel ADC. - memsensing,msa311 * New driver for this accelerometer. Includes a string helper for read/write. - richtek,rtq6056 * New driver and dt binding to support this current monitor used to measure power usage. - yamaha,yas530 * Support the YAS537 variant (series includes several fixes for other parts and new driver features). Staging graduation - adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using the posted RFC of that framework. Features - core * Large rework to make all the core IIO code use generic firmware properties. Includes switching some drivers over as well using newly provided generic interfaces and allowing removal of DT specific ones. * Support for gesture event types for single and double tap. Used in bosch,bma400. - atmel,at91-sama5d2 * Add support for temperature sensor which uses two muxed inputs to estimate the temperature. * Handle trackx bits of EMR register to improve temp sampling accuracy. * Runtime PM support. - liteon,ltrf216a * Add a _raw channel output to allow working around an issue with differing conversions equations that breaks some user space controls. - mexelis,mlx90632 * Support regulator control. - ti,tsc2046 * External reference voltage support. Clean up and minor fixes - Tree-wide * devm_clk_get_enabled() replacements of opencoded equivalent. * Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers). * Various minor warning and similar cleanup such as missing static markings. * strlcpy() to strscpy() for cases where return value not checked. * provide units.h entries for more HZ units and use them in drivers. - dt-bindings cleanup * Drop maintainers listss where the email address is bouncing. * Switch spi devices over to using spi-peripheral.yaml * Add some missing unevaluatedProperties / additionalProperties: false entries. - ABI docs * Add some missing channel type specific sampling frequency entries. * Add parameter names for callback parameters. - MAINTAINERS * Fix wrong ADI forum links. - core * lockdep class per device, to avoid an issue with nest when one IIO device is the consumer of another. * White space tweaks. - asc,dlhl60d * Use get_unaligned_be24 to avoid some unusual data manipulation and masking. - atmel,at91-sama5d2 * Fix wrong max value. * Improve error handling when measuring pressure and touch. * Add locks to remove races on updating oversampling / sampling freq. * Add missing calls in suspend and resume path to ensure state is correctly brought up if buffered capture was in use when suspend happened. * Error out of write_raw() callback if buffered capture enabled to avoid unpredictable behavior. * Handle different versions having different oversampling ratio support and drop excess error checking. * Cleanup magic value defines where the name is just the value and hence hurts readability. * Use read_avail() callback to provide info on possible oversampling ratios. * Correctly handle variable bit depth when doing oversampling on different supported parts. Also handle higher oversampling ratios. - fsl,imx8qxp * Don't ignore errors from regulator_get_voltage() so as to avoid some very surprising scaling. - invensense,icp10100 * Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made sense and is now deprecated. In this driver we just avoid double disabling in some paths. - maxim,max1363 * Drop consumer channel map provision by platform data. There have been better ways of doing this for years and there are no in tree users. - microchip,mcp3911 * Update status to maintained. - qcom,spmi-adc5 * Support measurement of LDO output voltage. - qcom,spmi-adc * Add missing channel available on SM6125 SoC. - st,stmpe * Drop requirement on node name in binding now that driver correctly doesn't enforce it. - stx104 * Move to more appropriate addac directory - ti,am335x * Document ti,am654-adc compatible already in use in tree. - ti,hmc5843 * Move dev_pm_ops out of header and use new pm macros to handle export. - yamaha,yas530 * Minor cleanups. * tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (142 commits) iio: pressure: icp10100: Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS(). iio: adc: max1363: Drop provision to provide an IIO channel map via platform data iio: accel: bma400: Add support for single and double tap events iio: Add new event type gesture and use direction for single and double tap iio: Use per-device lockdep class for mlock iio: adc: add max11205 adc driver dt-bindings: iio: adc: Add max11205 documentation file iio: magnetometer: yamaha-yas530: Use dev_err_probe() iio: magnetometer: yamaha-yas530: Make strings const in chip info iio: magnetometer: yamaha-yas530: Use pointers as driver data iio: adc: tsc2046: silent spi_device_id warning iio: adc: tsc2046: add vref support dt-bindings: iio: adc: ti,tsc2046: add vref-supply property iio: light: ltrf216a: Add raw attribute dt-bindings: iio: Add missing (unevaluated|additional)Properties on child nodes MAINTAINERS: fix Analog Devices forum links iio/accel: fix repeated words in comments dt-bindings: iio: accel: add dt-binding schema for msa311 accel driver iio: add MEMSensing MSA311 3-axis accelerometer driver dt-bindings: vendor-prefixes: add MEMSensing Microsystems Co., Ltd. ...
-
Greg Kroah-Hartman authored
Merge tag 'mhi-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next Manivannan writes: "MHI Host -------- - Print the modem name while probing the MHI host pci-generic driver. This has been exposed as a debug information so far but on a low storate embedded devices such as OpenWRT based products, this helps in identifying the attached modem without enabling the debug logs." * tag 'mhi-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi: bus: mhi: host: always print detected modem name
-
Greg Kroah-Hartman authored
Merge tag 'fpga-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-next Xu writes: FPGA Manager changes for 6.1-rc1 DFL - Matthew's change adds new device IDs supported by DFL. - Dan's change uses array_size() for memory allocation to prevent potential overflow Microchip - Conor's change adds MODULE_AUTHOR entry for microchip-spi driver - Krzysztof's change refines dt-bindings Intel m10 bmc secure update - Russ's change adds new device ID supported by the driver All patches have been reviewed on the mailing list, and have been in the last linux-next releases (as part of our for-next branch). Signed-off-by:
Xu Yilun <yilun.xu@intel.com> * tag 'fpga-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga: fpga: m10bmc-sec: d5005 bmc secure update driver fpga: prevent integer overflow in dfl_feature_ioctl_set_irq() dt-bindings: fpga: microchip,mpf-spi-fpga-mgr: use spi-peripheral-props.yaml fpga: microchip-spi: add missing module author entry fpga: dfl-pci: Add IDs for Intel N6000, N6001 and C6100 cards
-
- 16 Sep, 2022 1 commit
-
-
Koen Vandeputte authored
This harmless print provides a very easy way of knowing if the modem is detected properly during probing. Promote it to an informational print so no hassle is required enabling kernel debugging info to obtain it. The rationale here is that: On a lot of low-storage embedded devices, extensive kernel debugging info is not always present as this would increase it's size to much causing partition size issues. Signed-off-by:
Koen Vandeputte <koen.vandeputte@citymesh.com> Reviewed-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by:
Loic Poulain <loic.poulain@linaro.org> Link: https://lore.kernel.org/r/20220831100349.1488762-1-koen.vandeputte@citymesh.com [mani: added missing review tags] Signed-off-by:
-
- 12 Sep, 2022 1 commit
-
-
Stephen Rothwell authored
drivers/hwtracing/ptt/hisi_ptt.c:13:10: fatal error: linux/dma-iommu.h: No such file or directory 13 | #include <linux/dma-iommu.h> | ^~~~~~~~~~~~~~~~~~~ Caused by: commit ff0de066 ("hwtracing: hisi_ptt: Add trace function support for HiSilicon PCIe Tune and Trace device") interacting with: commit f2042ed2 ("iommu/dma: Make header private") from the iommu tree. Signed-off-by:Stephen Rothwell <sfr@canb.auug.org.au> Acked-by:
Robin Murphy <robin.murphy@arm.com> Acked-by:
Yicong Yang <yangyicong@hisilicon.com> [Fixed subject line and added changelog text] Signed-off-by:
Mathieu Poirier <mathieu.poirier@linaro.org>
-
- 11 Sep, 2022 1 commit
-
-
Russ Weight authored
Add a driver name for the D5005 BMC secure update driver. Different driver names are used for the N3000 and D5005 devices because future changes will add conditional code based on the device type (N3000 vs D5005). This change enables D5005 secure updates of BCM images, BMC firmware, static-region images, etc. Signed-off-by:
Russ Weight <russell.h.weight@intel.com> Acked-by:
-
- 09 Sep, 2022 3 commits
-
-
Xuezhi Zhang authored
Follow the advice of the Documentation/filesystems/sysfs.rst and show() should only use sysfs_emit() or sysfs_emit_at() when formatting the value to be returned to user space. Signed-off-by:
Xuezhi Zhang <zhangxuezhi1@coolpad.com> Link: https://lore.kernel.org/r/20220901013423.418464-1-zhangxuezhi3@gmail.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Shunsuke Mie authored
The dma_map_single() doesn't permit zero length mapping. It causes a follow panic. A panic was reported on arm64: [ 60.137988] ------------[ cut here ]------------ [ 60.142630] kernel BUG at kernel/dma/swiotlb.c:624! [ 60.147508] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [ 60.152992] Modules linked in: dw_hdmi_cec crct10dif_ce simple_bridge rcar_fdp1 vsp1 rcar_vin videobuf2_vmalloc rcar_csi2 v4l 2_mem2mem videobuf2_dma_contig videobuf2_memops pci_endpoint_test videobuf2_v4l2 videobuf2_common rcar_fcp v4l2_fwnode v4l2_asyn c videodev mc gpio_bd9571mwv max9611 pwm_rcar ccree at24 authenc libdes phy_rcar_gen3_usb3 usb_dmac display_connector pwm_bl [ 60.186252] CPU: 0 PID: 508 Comm: pcitest Not tainted 6.0.0-rc1rpci-dev+ #237 [ 60.193387] Hardware name: Renesas Salvator-X 2nd version board based on r8a77951 (DT) [ 60.201302] pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 60.208263] pc : swiotlb_tbl_map_single+0x2c0/0x590 [ 60.213149] lr : swiotlb_map+0x88/0x1f0 [ 60.216982] sp : ffff80000a883bc0 [ 60.220292] x29: ffff80000a883bc0 x28: 0000000000000000 x27: 0000000000000000 [ 60.227430] x26: 0000000000000000 x25: ffff0004c0da20d0 x24: ffff80000a1f77c0 [ 60.234567] x23: 0000000000000002 x22: 0001000040000010 x21: 000000007a000000 [ 60.241703] x20: 0000000000200000 x19: 0000000000000000 x18: 0000000000000000 [ 60.248840] x17: 0000000000000000 x16: 0000000000000000 x15: ffff0006ff7b9180 [ 60.255977] x14: ffff0006ff7b9180 x13: 0000000000000000 x12: 0000000000000000 [ 60.263113] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 [ 60.270249] x8 : 0001000000000010 x7 : ffff0004c6754b20 x6 : 0000000000000000 [ 60.277385] x5 : ffff0004c0da2090 x4 : 0000000000000000 x3 : 0000000000000001 [ 60.284521] x2 : 0000000040000000 x1 : 0000000000000000 x0 : 0000000040000010 [ 60.291658] Call trace: [ 60.294100] swiotlb_tbl_map_single+0x2c0/0x590 [ 60.298629] swiotlb_map+0x88/0x1f0 [ 60.302115] dma_map_page_attrs+0x188/0x230 [ 60.306299] pci_endpoint_test_ioctl+0x5e4/0xd90 [pci_endpoint_test] [ 60.312660] __arm64_sys_ioctl+0xa8/0xf0 [ 60.316583] invoke_syscall+0x44/0x108 [ 60.320334] el0_svc_common.constprop.0+0xcc/0xf0 [ 60.325038] do_el0_svc+0x2c/0xb8 [ 60.328351] el0_svc+0x2c/0x88 [ 60.331406] el0t_64_sync_handler+0xb8/0xc0 [ 60.335587] el0t_64_sync+0x18c/0x190 [ 60.339251] Code: 52800013 d2e00414 35fff45c d503201f (d4210000) [ 60.345344] ---[ end trace 0000000000000000 ]--- To fix it, this patch adds a checking the payload length if it is zero. Fixes: 343dc693 ("misc: pci_endpoint_test: Prevent some integer overflows") Cc: stable <stable@kernel.org> Signed-off-by:
Shunsuke Mie <mie@igel.co.jp> Link: https://lore.kernel.org/r/20220907020100.122588-2-mie@igel.co.jpSigned-off-by:
-
Shunsuke Mie authored
Each transfer test functions have same parameter checking code. This patch unites those to an introduced function. Signed-off-by:
-
