Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

[mchehab@s-opensource.com: fold several similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add CEC support for the tc358743 HDMI-CSI bridge.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add the missing CEC register defines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add an entry for the CEC GPIO driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add a simple HDMI CEC GPIO driver that sits on top of the cec-pin framework.

While I have heard of SoCs that use the GPIO pin for CEC (apparently an
early RockChip SoC used that), the main use-case of this driver is to
function as a debugging tool.

By connecting the CEC line to a GPIO pin on a Raspberry Pi 3 for example
it turns it into a CEC debugger and protocol analyzer.

With 'cec-ctl --monitor-pin' the CEC traffic can be analyzed.

But of course it can also be used with any hardware project where the
HDMI CEC line is hooked up to a pull-up gpio line.

In addition this has (optional) support for tracing HPD changes if the
HPD is connected to a GPIO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Document the bindings for the cec-gpio module for hardware where the
CEC line and optionally the HPD line are connected to GPIO lines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Document these new CEC events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH.

This is specifically meant for use with the upcoming cec-gpio driver
and makes it possible to trace when the HPD pin changes. Some HDMI
sinks do strange things with the HPD and this makes it easy to debug
this.

Note that this also moves the initialization of a devnode mutex and
list to the allocate_adapter function: if the HPD is high, then as
soon as the HPD interrupt is created an interrupt occurs and
cec_queue_pin_hpd_event() is called which requires that the devnode
mutex and list are initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

CEC_TX_STATUS_ERROR can be used if the HW cannot tell LOST_ARB and
LOW_DRIVE apart, or when some other error occurs. It is not a
replacement for NACK.

So the hardware must be able to tell the difference between OK, NACK and
'something else'.

Clarify the documentation (both public and kernel API) on this point.

Also fix two small typos (this messages -> this message).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The documentation talked about INITIAL_VALUE when the actual define is
INITIAL_STATE.

Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Use ktime_to_ns/ns_to_ktime. This makes it possible to work with older kernels
and the media_build compatibility system.

For the mainline kernel these functions are NOPs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Running CEC 1.4 compliance test we get the following error on test
11.1.6.2: "ERROR: The DUT did not broadcast a
<Report Physical Address> message to the unregistered device."

Fix this by letting GIVE_PHYSICAL_ADDR message respond to unregistered
device. Also, GIVE_DEVICE_VENDOR_ID and GIVE_FEATURES fall in the
same category so, respond also to these messages.

With this fix we pass CEC 1.4 official compliance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org>      # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The s5p-cec driver returned CEC_TX_STATUS_ERROR for the NACK condition.

Some digging into the datasheet uncovered the S5P_CEC_TX_STAT1 register where
bit 0 indicates if the transmit was nacked or not.

Use this to return the correct CEC_TX_STATUS_NACK status to userspace.

This was the only driver that couldn't tell a NACK from another error, and
that was very unusual. And a potential problem for applications as well.

Tested with my Odroid-U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: <stable@vger.kernel.org>      # for v4.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The ret variable can be returned uninitialized in the
imx_media_create_pad_vdev_lists() function is imxmd->num_vdevs is zero.
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The function vfe_set_selection is local to the source and does
not need to be in global scope, so make it static.

Cleans up sparse warning:
warning: symbol 'vfe_set_selection' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add missing init_list_head for the registered buffer list.
Absence of the init could lead to a unhandled kernel paging
request as below, when streamon/streamoff are called in row.

[338046.571321] Unable to handle kernel paging request at virtual address fffffffffffffe00
[338046.574849] pgd = ffff800034820000
[338046.582381] [fffffffffffffe00] *pgd=00000000b60f5003[338046.582545]
, *pud=00000000b1f31003
, *pmd=0000000000000000[338046.592082]
[338046.597754] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[338046.601671] Modules linked in: venus_enc venus_dec venus_core
usb_f_ecm g_ether usb_f_rndis u_ether libcomposite ipt_MASQUERADE
nf_nat_masquerade_ipv4 arc4 wcn36xx mac80211 btqcomsmd btqca iptable_nat
nf_co]
[338046.662408] CPU: 0 PID: 5433 Comm: irq/160-venus Tainted: G        W
4.9.39+ #232
[338046.668024] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC
(DT)
[338046.675268] task: ffff80003541cb00 task.stack: ffff800026e20000
[338046.682097] PC is at venus_helper_release_buf_ref+0x28/0x88
[venus_core]
[338046.688282] LR is at vdec_event_notify+0xe8/0x150 [venus_dec]
[338046.695029] pc : [<ffff000000af6c48>] lr : [<ffff000000a6fc60>]
pstate: a0000145
[338046.701256] sp : ffff800026e23bc0
[338046.708494] x29: ffff800026e23bc0 x28: 0000000000000000
[338046.718853] x27: ffff000000afd4f8 x26: ffff800031faa700
[338046.729253] x25: ffff000000afd790 x24: ffff800031faa618
[338046.739664] x23: ffff800003e18138 x22: ffff800002fc9810
[338046.750109] x21: ffff800026e23c28 x20: 0000000000000001
[338046.760592] x19: ffff80002a13b800 x18: 0000000000000010
[338046.771099] x17: 0000ffffa3d01600 x16: ffff000008100428
[338046.781654] x15: 0000000000000006 x14: ffff000089045ba7
[338046.792250] x13: ffff000009045bb6 x12: 00000000004f37c8
[338046.802894] x11: 0000000000267211 x10: 0000000000000000
[338046.813574] x9 : 0000000000032000 x8 : 00000000dc400000
[338046.824274] x7 : 0000000000000000 x6 : ffff800031faa728
[338046.835005] x5 : ffff80002a13b850 x4 : 0000000000000000
[338046.845793] x3 : fffffffffffffdf8 x2 : 0000000000000000
[338046.856602] x1 : 0000000000000003 x0 : ffff80002a13b800
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Since commit 29d2fef8 ("usb: catch attempts to submit urbs
with a vmalloc'd transfer buffer"), the AverMedia AverTV DVB-T
USB 2.0 (a800) fails to probe.

Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

We get a link error when V4L2_FLASH_LED_CLASS=m and AS3645A is built-in:

drivers/leds/leds-as3645a.o: In function `as3645a_v4l2_setup':
leds-as3645a.c:(.text+0x258): undefined reference to `v4l2_flash_init'
leds-as3645a.c:(.text+0x284): undefined reference to `v4l2_flash_indicator_init'
leds-as3645a.c:(.text+0x2a4): undefined reference to `v4l2_flash_release'
drivers/leds/leds-as3645a.o: In function `as3645a_remove':
leds-as3645a.c:(.text+0x784): undefined reference to `v4l2_flash_release'

This adds the same Kconfig dependency that the other V4L2 flash
drivers in drivers/leds use, to avoid that broken configuration.

Fixes: a56ba8fb ("media: leds: as3645a: Add LED flash class driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Those two ioctls were never used within the Kernel. Still, there
used to have compat32 code there (and an if #0 block at the core).

Get rid of them.

Fixes: 286fe1ca ("media: dmx.h: get rid of DMX_GET_CAPS")
Fixes: 13adefbe ("media: dmx.h: get rid of DMX_SET_SOURCE")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

This reverts commit d2180e0c.

The commit was flawed in that if the device_node pointers are different,
then in fact a different device is present and the device node could be
different in ways other than full_name.

As Frank Rowand explained:

"When an overlay (1) is removed, all uses and references to the nodes and
properties in that overlay are no longer valid.  Any driver that uses any
information from the overlay _must_ stop using any data from the overlay.
Any driver that is bound to a new node in the overlay _must_ unbind.  Any
driver that became bound to a pre-existing node that was modified by the
overlay (became bound after the overlay was applied) _must_ adjust itself
to account for any changes to that node when the overlay is removed.  One
way to do this is to unbind when notified that the overlay is about to
be removed, then to re-bind after the overlay is completely removed.

If an overlay (2) is subsequently applied, a node with the same
full_name as from overlay (1) may exist.  There is no guarantee
that overlay (1) and overlay (2) are the same overlay, even if
that node has the same full_name in both cases."

Also, there's not sufficient overlay support in mainline to actually
remove and re-apply an overlay to hit this condition as overlays can
only be applied from in kernel APIs.

Fixes: d2180e0c ("[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay")

Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The calloc function returns either a null pointer or a pointer to the
allocated space. Add the second case that is missed.

Fixes: da22013f ("atomisp: remove indirection from sh_css_malloc")
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

This reverts commit 5be2b76a.

Only when the lirc device is freed, should we drop our reference to
rc_dev, else we the rc_dev is freed to early. If userspace has
a file descriptor open during unplug, it goes bang.

==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x7bb/0x1e10
Read of size 8 at addr ffff8801d7d61ed0 by task ir-rec/2609

-snip-
 mutex_lock_nested+0x1b/0x20
 ? mutex_lock_nested+0x1b/0x20
 rc_close.part.6+0x20/0x60 [rc_core]
 rc_close+0x13/0x20 [rc_core]
 lirc_dev_fop_close+0x62/0xd0 [lirc_dev]
 __fput+0x236/0x410
 ? fput+0xb0/0xb0
 ? do_raw_spin_trylock+0x110/0x110
 ? set_rq_offline.part.70+0xa0/0xa0
 ____fput+0xe/0x10
 task_work_run+0x116/0x180
 ? task_work_cancel+0x170/0x170
 ? _raw_spin_unlock+0x27/0x40
 ? switch_task_namespaces+0x5f/0x90
 do_exit+0x68b/0xe80

Cc: stable@vger.kernel.org # For Kernel 4.13
Fixes: 5be2b76a ("[media] lirc_dev: remove superfluous get/put_device() calls")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Avoid this warning:
	/devel/v4l/docs/Documentation/media/v4l-drivers/qcom_camss.rst:: WARNING: document isn't included in any toctree
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Adjust dvb ca.h, dmx.h and frontend.h in order to make
checkpatch happier. Now, it only complains about the typedefs,
and those are there just to provide backward userspace
compatibility.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

There's a chapter for the legacy APIs. Move the frontend DVBv3
API to it, and update the chapter's introduction accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Adjust the table to be better displayed on PDF output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

There appears to be an issue in using \small in certain cases on Sphinx
1.4 and 1.5. Other format documents don't use \small either, remove it
from here as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

[mchehab@s-opensource.com: kept tabularcolumns - readjusted - and
 add a few blank lines for it to display better]
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Right now, Sphinx unconditionally creates a blank page with
just "Contents:" on it, on PDF output. While this makes sense
for html, it doesn't o PDF, as LaTeX does what's required
automatically.

Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

On several tables, the color sample location table preamble is
written as:
	Color Sample Location..
Instead of:
	Color Sample Location:

I suspect that the repetition of such pattern was due to some
copy-and-paste (or perhaps some error during DocBook conversion).

Anyway, fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

While doing a visual inspection with Sphinx 1.5, I noticed that
one of the columns was smaller than the text written there.

As this is the only thing I noticed with Sphinx 1.5, I suspect
that this was also a problem with Sphinx 1.4. Yet, I opted to
touch it in a way that wouldn't cause backward issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

On all vivid parameters, there's an space after the parameter,
except for "DV Timings Signal Mode". That makes this single one
to be written in bold, and, at PDF output, at the same line as
its description.

Use the same convention as the other parameters, in order to
adjust its output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

It doesn't make any sense having a driver programming's chapter
at the uAPI book, as this is related to kernel API. Also,
we now have such kAPI book where V4L2 driver programming is covered.

So, get rid of this left-over.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

There's an important note there, but it is not using the
ReST markup. So, it doesn't get any visual highlight on
the output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Most tables there don't fit on 80 columns. Some are very big.

While those tables are actually generated via scripts, every
time a new board is added, the entire table could be reformatted.
>From the diffstat PoV, that's bad, as it is hard to see what
happened.

One such example is at changeset 4868f6e1fce6 ("media:
em28xx-cardlist.rst: update to reflect last changes"):

The USB ID for "Plextor ConvertX PX-AV100U" was added to card
number 9, with caused the entire table to be reformatted.

So, instead, use flat-tables. While here, fix PDF output,
by adding tablecolumns to the tables that need it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

There were some new board additions. Update the cardlist
accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The tables there don't quite fit on PDF output.

Adjust it by adding a tabularcolumns macro.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The "Table of Contents" of a PDF file is generated only once,
at the beginning fo the output. It doesn't produce it on
each part.

So, don't output this text on each part of the document.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Several tables at this media book chapter have issues
when PDF is produced. Adjust them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Some cells are too small to fit the text written to it.

Increase it. No text changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

A literal box provides a better visual when pdf and html output
is generated for things like the output of a sysfs devnode.
It alsod matches other conventions used within the media book.

So, use it.

While here, use literals for protocol names.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>