Vlad Buslov says:

====================
Additional tests for action API

Add two new tests for action create/change code.
====================
Acked-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify cleanup of failed actions batch change where second action in batch
fails after successful init of first action.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify cleanup of failed actions batch add where second action in batch
fails after successful init of first action.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: add support for pm_ops

This series adds support for pm_ops in the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To implement the system suspend/resume functions, the NIC driver needs
to support:
1. When the system enters the suspend mode, the driver needs to
implement the suspend callback function of the NIC device. The driver
needs to mute the device, stop all RX/TX activities of the device, and
unmap the interrupt.
2. When the system enters the resume mode, the driver needs to
implement the resume callback function of the NIC device and restore
the device to the state before suspension.

When the system enters the suspend and resume mode, the NIC driver
actually executes the PF function reset process.

When the PFs are suspending/resuming, VFs also enter the suspend/resume
state because the PFs trigger the VFs to reset, therefore no operation
is required when the VF pci_driver is suspending or resuming.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flr_prepare/flr_done functions are not only used in the FLR scenario,
but also used in the suspend/resume.

Change the function names to prepare_for_reset/rebuild_for_reset, change
the flr_prepare/flr_done to reset_prepare/reset_done in hnae3_ae_ops.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: hwstamp tweaks

A few little changes after review comments and
additional internal testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the configuration is locked before
operating on it for the replay.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split the call into ionic_lif_hwstamp_set() to have two
separate interfaces, one from the ioctl() for changing the
configuration and one for replaying the current configuration
after a FW RESET.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

When starting the queues in the link-check, don't go into
the BROKEN state if the return was EBUSY.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

When returning after a firmware reset, re-start the
PTP after we've restarted the general queues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set the SKBTX_IN_PROGRESS when offloading the Tx timestamp.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the device is in a Tx offload mode before calling the
hwstamp offload xmit.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't need to look for HAVE_HWSTAMP_TX_ONESTEP_P2P in the
upstream kernel.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up variable declarations.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek Behún says:

====================
net: phy: marvell10g updates

Here are some updates for marvell10g PHY driver.

I am still working on some more changes for this driver, but I would
like to have at least something reviewed / applied.

Changes since v3:
- added Andrew's Reviewed-by tags
- removed patches adding variadic-macro library and bitmap
  initialization macro - it causes warning that we are not currently
  able to fix easily. Instead the supported_interfaces bitmap is now
  initialized via a chip specific method
- added explanation of mactype initialization to commit message of patch
  07/16
- fixed repeated word in commit message of second to last patch

Changes since v2:
- code refactored to use an additional structure mv3310_chip describing
  mv3310 specific properties / operations for PHYs supported by this
  driver
- added separate phy_driver structures for 88X3340 and 88E2111
- removed 88E2180 specific code (dual-port and quad-port SXGMII modes
  are ignored for now)

Changes since v1:
- added various MACTYPEs support also for 88E21XX
- differentiate between specific models with same PHY_ID
- better check for compatible interface
- print exact model
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add myself as maintainer of the marvell10g ethernet PHY driver, in
addition to Russell King.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This module supports not only Alaska X, but also Alaska M.

Change module description appropriately.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

88E2111 is a variant of 88E2110 which does not support 5 gigabit speeds.

Differentiate these variants via the match_phy_device() method, since
they have the same PHY ID.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add constants for 2.5G and 5G speed in PCS speed register into mdio.h.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver name "mv88x2110" should be instead "mv88e2110".
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 88X3340 contains 4 cores similar to 88X3310, but there is a
difference: it does not support xaui host mode. Instead the
corresponding MACTYPE means
  rxaui / 5gbase-r / 2500base-x / sgmii without AN
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the only "changing" MACTYPE we support is when the PHY changes
between
  10gbase-r / 5gbase-r / 2500base-x / sgmii

Add support for
  usxgmii
  xaui / 5gbase-r / 2500base-x / sgmii
  rxaui / 5gbase-r / 2500base-x / sgmii
and also
  5gbase-r / 2500base-x / sgmii
for 88E2110.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have a chip structure, we can store the temperature reading
method in this structure (OOP style).
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 88E2110 does not support xaui nor rxaui modes. Check for correct
interface mode for different chips.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for all rate matching modes for 88X3310 (currently only
10gbase-r is supported, but xaui and rxaui can also be used).

Add support for rate matching for 88E2110 (on 88E2110 the MACTYPE
register is at a different place).

Currently rate matching mode is selected by strapping pins (by setting
the MACTYPE register). There is work in progress to enable this driver
to deduce the best MACTYPE from the knowledge of which interface modes
are supported by the host, but this work is not finished yet.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add all MACTYPE definitions for 88E2110, 88E2180, 88E2111 and 88E2181.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add all MACTYPE definitions for 88X3310, 88X3310P, 88X3340 and 88X3340P.

In order to have consistent naming, rename
MV_V2_33X0_PORT_CTRL_MACTYPE_RATE_MATCH to
MV_V2_33X0_PORT_CTRL_MACTYPE_10GBASER_RATE_MATCH.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename port control registers to indicate that they are valid only for
88X33x0, not for 88E21x0.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These modes are also supported by these PHYs.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This space should be a tab instead.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MV_V2_PORT_MAC_TYPE_* is part of the CTRL register. Rename to
MV_V2_PORT_CTRL_MACTYPE_*.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>