QCA original code report port instability and sa that SGMII also require
to set internal delay. Generalize the rgmii delay function and apply the
advised value if they are not defined in DT.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

QCA8328 switch is the bigger brother of the qca8327. Same regs different
chip. Change the function to set the correct pin layout and introduce a
new match_data to differentiate the 2 switch as they have the same ID
and their internal PHY have the same ID.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

QCA8328 is the bigger brother of qca8327. Document the new compatible
binding and add some information to understand the various switch
compatible.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some qca8327 switch require to force the ignore of power on sel
strapping. Some switch require to set the led open drain mode in regs
instead of using strapping. While most of the device implements this
using the correct way using pin strapping, there are still some broken
device that require to be set using sw regs.
Introduce a new binding and support these special configuration.
As led open drain require to ignore pin strapping to work, the probe
fails with EINVAL error with incorrect configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document new binding qca,ignore-power-on-sel used to ignore
power on strapping and use sw regs instead.
Document qca,led-open.drain to set led to open drain mode, the
qca,ignore-power-on-sel is mandatory with this enabled or an error will
be reported.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support enabling PLL on the SGMII CPU port. Some device require this
special configuration or no traffic is transmitted and the switch
doesn't work at all. A dedicated binding is added to the CPU node
port to apply the correct reg on mac config.
Fail to correctly configure sgmii with qca8327 switch and warn if pll is
used on qca8337 with a revision greater than 1.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document qca,sgmii-enable-pll binding used in the CPU nodes to
enable SGMII PLL on MAC config.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Future proof commit. This switch have 2 CPU ports and one valid
configuration is first CPU port set to sgmii and second CPU port set to
rgmii-id. The current implementation detects delay only for CPU port
zero set to rgmii and doesn't count any delay set in a secondary CPU
port. Drop the current delay scan function and move it to the sgmii
parser function to generalize and implicitly add support for secondary
CPU port set to rgmii-id. Introduce new logic where delay is enabled
also with internal delay binding declared and rgmii set as PHY mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently CPU port is always hardcoded to port 0. This switch have 2 CPU
ports. The original intention of this driver seems to be use the
mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration
where device have connected only the CPU port 6. To skip the
introduction of a new binding, rework the driver to address the
secondary CPU port as primary and drop any reference of hardcoded port.
With configuration of mac06 exchange, just skip the definition of port0
and define the CPU port as a secondary. The driver will autoconfigure
the switch to use that as the primary CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The switch now support CPU port to be set 6 instead of be hardcoded to
0. Document support for it and describe logic selection.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for this in the qca8k driver. Also add support for SGMII
rx/tx clock falling edge. This is only present for pad0, pad5 and
pad6 have these bit reserved from Documentation. Add a comment that this
is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and
setting falling in port0 applies to both configuration with sgmii used
for port0 or port6.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add names and descriptions of additional PORT0_PAD_CTRL properties.
qca,sgmii-(rx|tx)clk-falling-edge are for setting the respective clock
phase to failling edge.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing mac power sel support needed for ipq8064/5 SoC that require
1.8v for the internal regulator port instead of the default 1.5v.
If other device needs this, consider adding a dedicated binding to
support this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable err is being initialized with a value that is never read, it
is being updated immediately afterwards. The assignment is redundant and
can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the 32-bit arch with 64-bit DMA seems to rare those days,
and page pool might carry a lot of code and complexity for
systems that possibly.

So disable dma mapping support for such systems, if drivers
really want to work on such systems, they have to implement
their own DMA-mapping fallback tracking outside page_pool.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Srujana Challa says:

====================
octeontx2-af: Miscellaneous changes for CPT

This patchset consists of miscellaneous changes for CPT.
First patch enables the CPT HW interrupts, second patch
adds support for CPT LF teardown in non FLR path and
final patch does CPT CTX flush in FLR handler.

v2:
- Fixed a warning reported by kernel test robot.
====================

Link: https://lore.kernel.org/r/20211013055621.1812301-1-schalla@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Adds support to flush or invalidate CPT CTX entries as part of FLR
and also provides a mailbox to flush CPT CTX entries in case of
graceful exit.
This patch also adds support for AF -> CPT PF uplink mailbox messages
and adds a new mbox message to submit a CPT instruction from AF.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Perform CPT LF teardown in non FLR path as well via cpt_lf_free()
Currently CPT LF teardown and reset sequence is only
done when FLR is handled with CPT LF still attached.

This patch also fixes cpt_lf_alloc() to set EXEC_LDWB in
CPT_AF_LFX_CTL2 when being completely overwritten as that is
the default value and is better for performance.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch enables and registers interrupt handler for CPT HW
interrupts.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On i386, when builtin (not a loadable module), the winbond-840 driver
inspects boot_cpu_data to see what CPU family it is running on, and
then acts on that data. The "family" struct member (x86) does not exist
when running on UML, so prevent that test and do the default action.

Prevents this build error on UML + i386:

../drivers/net/ethernet/dec/tulip/winbond-840.c: In function ‘init_registers’:
../drivers/net/ethernet/dec/tulip/winbond-840.c:882:19: error: ‘struct cpuinfo_um’ has no member named ‘x86’
  if (boot_cpu_data.x86 <= 4) {

Fixes: 68f5d3f3 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20211014050606.7288-1-rdunlap@infradead.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

On a UML build, the igc_ptp driver uses CONFIG_X86_TSC for timestamp
conversion. The function that is used is not available on UML builds,
so have the function use the default system_counterval_t timestamp
instead for UML builds.

Prevents this build error on UML:

../drivers/net/ethernet/intel/igc/igc_ptp.c: In function ‘igc_device_tstamp_to_system’:
../drivers/net/ethernet/intel/igc/igc_ptp.c:777:9: error: implicit declaration of function ‘convert_art_ns_to_tsc’ [-Werror=implicit-function-declaration]
  return convert_art_ns_to_tsc(tstamp);
../drivers/net/ethernet/intel/igc/igc_ptp.c:777:9: error: incompatible types when returning type ‘int’ but ‘struct system_counterval_t’ was expected
  return convert_art_ns_to_tsc(tstamp);

Fixes: 68f5d3f3 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/r/20211014050516.6846-1-rdunlap@infradead.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

On i386, when builtin (not a loadable module), the fealnx driver
inspects boot_cpu_data to see what CPU family it is running on, and
then acts on that data. The "family" struct member (x86) does not exist
when running on UML, so prevent that test and do the default action.

Prevents this build error on UML + i386:

../drivers/net/ethernet/fealnx.c: In function ‘netdev_open’:
../drivers/net/ethernet/fealnx.c:861:19: error: ‘struct cpuinfo_um’ has no member named ‘x86’

Fixes: 68f5d3f3 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20211014050500.5620-1-rdunlap@infradead.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Adding comment to avoid the misusing of netvsc_xdp_xmit().
Otherwise the value of skb->queue_mapping could be 0 and
then the return value of skb_get_rx_queue() could be MAX_U16
cause by overflow.
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1634174786-1810351-1-git-send-email-jiasheng@iscas.ac.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
Minor managed neighbor follow-ups

Minor follow-up series to address prior feedback from David and Jakub.
Patch 1 adds a build time assertion to prevent overflows when shifting
in extended flags, patch 2 is a cleanup to use NLA_POLICY_MASK instead
of open-coding invalid flags rejection and patch 3 rejects creating new
neighbors with NUD_PERMANENT & NTF_MANAGED. For details, see individual
patches.
====================

Link: https://lore.kernel.org/r/20211013132140.11143-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The combination of NUD_PERMANENT + NTF_MANAGED is not supported and does
not make sense either given the former indicates a static/fixed neighbor
entry whereas the latter a dynamically resolved one. While it is possible
to transition from one over to the other, we should however reject such
creation attempts.

Fixes: 7482e384 ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of open-coding a check for invalid bits in NTF_EXT_MASK, we can just
use the NLA_POLICY_MASK() helper instead, and simplify NDA_FLAGS_EXT sanity
check this way.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, NDA_FLAGS_EXT flags allow a maximum of 24 bits to be used for
extended neighbor flags. These are eventually fed into neigh->flags by
shifting with NTF_EXT_SHIFT as per commit 2c611ad9 ("net, neigh:
Extend neigh->flags to 32 bit to allow for extensions").

If really ever needed in future, the full 32 bits from NDA_FLAGS_EXT can
be used, it would only require to move neigh->flags from u32 to u64 inside
the kernel.

Add a build-time assertion such that when extending the NTF_EXT_MASK with
new bits, we'll trigger an error once we surpass the 24th bit. This assumes
that no bit holes in new NTF_EXT_* flags will slip in from UAPI, but I
think this is reasonable to assume.
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The variable pp is not in use - delete it.
Signed-off-by: Yuval Shaia <yshaia@marvell.com>
Link: https://lore.kernel.org/r/20211013064921.26346-1-yshaia@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

PHY driver dp83867 has rich supports for OF-platform to fine-tune the PHY
chip during phy configuration. However, for non-OF platform, certain PHY
tunable parameters such as IO impedance and RX & TX internal delays are
critical and should be initialized to its default during PHY driver probe.
Tested-by: Clement <clement@intel.com>
Signed-off-by: Lay, Kuan Loon <kuan.loon.lay@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211013065941.2124858-1-boon.leong.ong@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If the PTP_PEROUT_DUTY_CYCLE flag is set, then check if the
request_on value in ptp_perout_request matches the pre-defined
values or a toggle option.
Return a failure if the value is not supported.

Preserve the old behaviors if the PTP_PEROUT_DUTY_CYCLE flag is not
set.

Tested with an oscilloscope on EVB-LAN7430:
e.g., to output PPS 1sec period 500mS on (high) to GPIO 2.
 ./testptp -L 2,2
 ./testptp -p 1000000000 -w 500000000
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Link: https://lore.kernel.org/r/1634046593-64312-1-git-send-email-yuiko.oshino@microchip.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tools/testing/selftests/net/ioam6.sh
  7b1700e0 ("selftests: net: modify IOAM tests for undef bits")
  bf77b140 ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Moving the of_net code from drivers/of/ to net/core means we
no longer stub out the helpers when networking is disabled,
which leads to a randconfig build failure with at least one
ARM platform that calls this from non-networking code:

arm-linux-gnueabi-ld: arch/arm/mach-mvebu/kirkwood.o: in function `kirkwood_dt_eth_fixup':
kirkwood.c:(.init.text+0x54): undefined reference to `of_get_mac_address'

Restore the way this worked before by changing that #ifdef
check back to testing for both CONFIG_OF and CONFIG_NET.

Fixes: e330fb14 ("of: net: move of_net under net/")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211014090055.2058949-1-arnd@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Quite calm.

  The noisy DSA driver (embedded switches) changes, and adjustment to
  IPv6 IOAM behavior add to diffstat's bottom line but are not scary.

  Current release - regressions:

   - af_unix: rename UNIX-DGRAM to UNIX to maintain backwards
     compatibility

   - procfs: revert "add seq_puts() statement for dev_mcast", minor
     format change broke user space

  Current release - new code bugs:

   - dsa: fix bridge_num not getting cleared after ports leaving the
     bridge, resource leak

   - dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
     bridges using VID 0, prevent packet drops if pvid is removed

   - dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent HW
     getting confused about station to VLAN mapping

  Previous releases - regressions:

   - virtio-net: fix for skb_over_panic inside big mode

   - phy: do not shutdown PHYs in READY state

   - dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's, fix link
     LED staying lit after ifdown

   - mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)

   - mqprio: Correct stats in mqprio_dump_class_stats()

   - ice: fix deadlock for Tx timestamp tracking flush

   - stmmac: fix feature detection on old hardware

  Previous releases - always broken:

   - sctp: account stream padding length for reconf chunk

   - icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()

   - isdn: cpai: check ctr->cnr to avoid array index out of bound

   - isdn: mISDN: fix sleeping function called from invalid context

   - nfc: nci: fix potential UAF of rf_conn_info object

   - dsa: microchip: prevent ksz_mib_read_work from kicking back in
     after it's canceled in .remove and crashing

   - dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged
     ports

   - dsa: sja1105, ocelot: break circular dependency between switch and
     tag drivers

   - dsa: felix: improve timestamping in presence of packe loss

   - mlxsw: thermal: fix out-of-bounds memory accesses

  Misc:

   - ipv6: ioam: move the check for undefined bits to improve
     interoperability"

* tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits)
  icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
  MAINTAINERS: Update the devicetree documentation path of imx fec driver
  sctp: account stream padding length for reconf chunk
  mlxsw: thermal: Fix out-of-bounds memory accesses
  ethernet: s2io: fix setting mac address during resume
  NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
  NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
  nfc: fix error handling of nfc_proto_register()
  Revert "net: procfs: add seq_puts() statement for dev_mcast"
  net: encx24j600: check error in devm_regmap_init_encx24j600
  net: korina: select CRC32
  net: arc: select CRC32
  net: dsa: felix: break at first CPU port during init and teardown
  net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports
  net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent
  net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
  net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
  net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
  net: mscc: ocelot: deny TX timestamping of non-PTP packets
  net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb
  ...

random_ether_addr() was the original name of the helper which
was kept for backward compatibility (?) after the rename in
commit 0a4dd594 ("etherdevice: Rename random_ether_addr
to eth_random_addr").

We have a single random_ether_addr() caller left in tree
while there are 70 callers of eth_random_addr().
Time to drop this define.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20211013205450.328092-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
ethernet: more netdev->dev_addr write removals

Another series removing direct writes to netdev->dev_addr.
====================

Link: https://lore.kernel.org/r/20211013204435.322561-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

This patch takes care of drivers which cast netdev->dev_addr to
a 16bit type, often with an explicit byte order.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A handful of drivers contains loops assigning the mac
addr byte by byte. Convert those to eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A straggler I somehow missed in the automated conversion in
commit 9ca01b25 ("ethernet: use of_get_ethdev_address()").
Use the new helper instead of using netdev->dev_addr directly.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A handful of drivers use sizeof(addr) for the size of
the address, after manually confirming the size is
indeed 6 convert them to eth_hw_addr_set().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>