Add support for ETHTOOL_COALESCE_TX_AGGR for configuring the tx
aggregation settings.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tx packets aggregation.

Bidirectional TCP throughput tests through iperf with low-cat
Thread-x based modems revelead performance issues both in tx
and rx.

The Windows driver does not show this issue: inspecting USB
packets revealed that the only notable change is the driver
enabling tx packets aggregation.

Tx packets aggregation is by default disabled and can be enabled
by increasing the value of ETHTOOL_A_COALESCE_TX_MAX_AGGR_FRAMES.

The maximum aggregated size is by default set to a reasonably low
value in order to support the majority of modems.

This implementation is based on patches available in Code Aurora
repositories (msm kernel) whose main authors are

Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the following ethtool tx aggregation parameters:

ETHTOOL_A_COALESCE_TX_AGGR_MAX_BYTES
Maximum size in bytes of a tx aggregated block of frames.

ETHTOOL_A_COALESCE_TX_AGGR_MAX_FRAMES
Maximum number of frames that can be aggregated into a block.

ETHTOOL_A_COALESCE_TX_AGGR_TIME_USECS
Time in usecs after the first packet arrival in an aggregated
block for the block to be sent.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arun Ramadoss says:

====================
net: dsa: microchip: add PTP support for KSZ9563/KSZ8563 and LAN937x

KSZ9563/KSZ8563 and  LAN937x switch are capable for supporting IEEE 1588 PTP
protocol.  LAN937x has the same PTP register set similar to KSZ9563, hence the
implementation has been made common for the KSZ switches.  KSZ9563 does not
support two step timestamping but LAN937x supports both.  Tested the 1step &
2step p2p timestamping in LAN937x and p2p1step timestamping in KSZ9563.

This patch series is based on the Christian Eggers PTP support for KSZ9563.
Applied the Christian patch and updated as per the latest refactoring of KSZ
series code. The features added on top are PTP packet Interrupt
implementation based on nested handler, LAN937x two step timestamping and
programmable per_out pins.

Link: https://www.spinics.net/lists/netdev/msg705531.html

Patch v7 -> v8
- set skb->ip_summed = CHECKSUM_NONE after updating the checksum

Patch v6 -> v7
- Corrected the misplaced spaces and tabs
- Added mutex lock in do_aux_work
- Replaced 0/1 with false/true for ts_en
- SKB_TX_INPROGRESS flag is set before dsa_enqueue_skb
- Removed the fallthrough keyword
- pdelay_resp header correction is performed based on
  KSZ_SKB_CB(skb)->update_correction instead of clone

Patch v5 -> v6
- Rebased to latest net-next and renamed from RFC to patch net-next.

Patch v4 -> v5
- Replaced irq_domain_add_simple with irq_doamin_add_linear
- Used the helper diff_by_scaled_ppm() for adjfine.

Patch v3 -> v4
- removed IRQF_TRIGGER_FALLING from the request_threaded_irq of ptp msg
- addressed review comments on patch 10 periodic output
- added sign off in patch 6 & 9
- reverted to set PTP_1STEP bit for lan937x which is missed during v3 regression

Patch v2-> v3
- used port_rxtstamp for reconstructing the absolute timestamp instead of
tagger function pointer.
- Reverted to setting of 802.1As bit.

Patch v1 -> v2
- GPIO perout enable bit is different for LAN937x and KSZ9x. Added new patch
for configuring LAN937x programmable pins.
- PTP enabled in hardware based on both tx and rx timestamping of all the user
ports.
- Replaced setting of 802.1AS bit with P2P bit in PTP_MSG_CONF1 register.

RFC v2 -> Patch v1
- Changed the patch author based on past patch submission
- Changed the commit message prefix as net: dsa: microchip: ptp
Individual patch changes are listed in correspondig commits.

RFC v1 -> v2
- Added the p2p1step timestamping and conditional execution of 2 step for
  LAN937x only.
- Added the periodic output support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is difference in implementation of per_out pins between KSZ9563
and LAN937x. In KSZ9563, Timestamping control register (0x052C) bit 6,
if 1 - timestamp input and 0 - trigger output. But it is opposite for
LAN937x 1 - trigger output and 0 - timestamp input.
As per per_out gpio pins, KSZ9563 has four Led pins and two dedicated
gpio pins. But in LAN937x dedicated gpio pins are removed instead there
are up to 10 LED pins out of which LED_0 and LED_1 can be mapped to PTP
tou 0, 1 or 2. This patch sets the bit 6 in 0x052C register and
configure the LED override and source register for LAN937x series of
switches alone.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LAN937x series of switches support 2 step timestamping mechanism. There
are timestamp correction calculation performed in ksz_rcv_timestamp and
ksz_xmit_timestamp which are applicable only for p2p1step. To check
whether the 2 step is enabled or not in tag_ksz.c introduced the helper
function in taggger_data to query it from ksz_ptp.c. Based on whether 2
step is enabled or not, timestamp calculation are performed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two programmable pins available for Trigger output unit to
generate periodic pulses. This patch add verify_pin for the available 2
pins and configure it with respect to GPIO index for the TOU unit.

Tested using testptp
./testptp -i 0 -L 0,2
./testptp -i 0 -d /dev/ptp0 -p 1000000000
./testptp -i 1 -L 1,2
./testptp -i 1 -d /dev/ptp0 -p 100000000
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LAN937x and KSZ PTP supported switches has Three Trigger output unit.
This TOU can used to generate the periodic signal for PTP. TOU has the
cycle width register of 32 bit in size and period width register of 24
bit, each value is of 8ns so the pulse width can be maximum 125ms.

Tested using ./testptp -d /dev/ptp0 -p 1000000000 -w 100000000 for
generating the 10ms pulse width
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For PDelay_Resp messages we will likely have a negative value in the
correction field. The switch hardware cannot correctly update such
values (produces an off by one error in the UDP checksum), so it must be
moved to the time stamp field in the tail tag. Format of the correction
field is 48 bit ns + 16 bit fractional ns.  After updating the
correction field, clone is no longer required hence it is freed.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the routines for transmission of ptp packets. When the
ptp pdelay_req packet to be transmitted, it uses the deferred xmit
worker to schedule the packets.
During irq_setup, interrupt for Sync, Pdelay_req and Pdelay_rsp are
enabled. So interrupt is triggered for all three packets. But for
p2p1step, we require only time stamp of Pdelay_req packet. Hence to
avoid posting of the completion from ISR routine for Sync and
Pdelay_resp packets, ts_en flag is introduced. This controls which
packets need to processed for timestamp.
After the packet is transmitted, ISR is triggered. The time at which
packet transmitted is recorded to separate register.
This value is reconstructed to absolute time and posted to the user
application through socket error queue.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rx Timestamping is done through 4 additional bytes in tail tag.
Whenever the ptp packet is received, the 4 byte hardware time stamped
value is added before 1 byte tail tag. Also, bit 7 in tail tag indicates
it as PTP frame. This 4 byte value is extracted from the tail tag and
reconstructed to absolute time and assigned to skb hwtstamp.
If the packet received in PDelay_Resp, then partial ingress timestamp
is subtracted from the correction field. Since user space tools expects
to be done in hardware.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For P2P delay measurement, the ingress time stamp of the PDelay_Req is
required for the correction field of the PDelay_Resp. The application
echoes back the correction field of the PDelay_Req when sending the
PDelay_Resp.

Some hardware (like the ZHAW InES PTP time stamping IP core) subtracts
the ingress timestamp autonomously from the correction field, so that
the hardware only needs to add the egress timestamp on tx. Other
hardware (like the Microchip KSZ9563) reports the ingress time stamp via
an interrupt and requires that the software provides this time stamp via
tail-tag on tx.

In order to avoid introducing a further application interface for this,
the driver can simply emulate the behavior of the InES device and
subtract the ingress time stamp in software from the correction field.

On egress, the correction field can either be kept as it is (and the
time stamp field in the tail-tag is set to zero) or move the value from
the correction field back to the tail-tag.

Changing the correction field requires updating the UDP checksum (if UDP
is used as transport).
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PTP Interrupt mask and status register differ from the global and port
interrupt mechanism by two methods. One is that for global/port
interrupt enabling we have to clear the bit but for ptp interrupt we
have to set the bit. And other is bit12:0 is reserved in ptp interrupt
registers. This forced to not use the generic implementation of
global/port interrupt method routine. This patch implement the ptp
interrupt mechanism to read the timestamp register for sync, pdelay_req
and pdelay_resp.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is used for reconstructing the absolute time from the 32bit
hardware time stamping value. The do_aux ioctl is used for reading the
ptp hardware clock and store it to global variable.
The timestamped value in tail tag during rx and register during tx are
32 bit value (2 bit seconds and 30 bit nanoseconds). The time taken to
read entire ptp clock will be time consuming. In order to speed up, the
software clock is maintained. This clock time will be added to 32 bit
timestamp to get the absolute time stamp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the PTP is enabled in hardware bit 6 of PTP_MSG_CONF1 register, the
transmit frame needs additional 4 bytes before the tail tag. It is
needed for all the transmission packets irrespective of PTP packets or
not.
The 4-byte timestamp field is 0 for frames other than Pdelay_Resp. For
the one-step Pdelay_Resp, the switch needs the receive timestamp of the
Pdelay_Req message so that it can put the turnaround time in the
correction field.
Since PTP has to be enabled for both Transmission and reception
timestamping, driver needs to track of the tx and rx setting of the all
the user ports in the switch.
Two flags hw_tx_en and hw_rx_en are added in ksz_port to track the
timestampping setting of each port. When any one of ports has tx or rx
timestampping enabled, bit 6 of PTP_MSG_CONF1 is set and it is indicated
to tag_ksz.c through tagger bytes. This flag adds 4 additional bytes to
the tail tag.  When tx and rx timestamping of all the ports are disabled,
then 4 bytes are not added.

Tested using hwstamp -i <interface>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the routine for get_ts_info, hwstamp_get, set. This enables
the PTP support towards userspace applications such as linuxptp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix clock register.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Emeel Hakim says:

====================
Add support to offload macsec using netlink update

This series adds support for offloading macsec as part of the netlink
update routine, command example:

  $ ip link set link eth2 macsec0 type macsec offload mac

The above is done using the IFLA_MACSEC_OFFLOAD attribute hence
the second patch of dumping this attribute as part of the macsec
dump.
====================

Link: https://lore.kernel.org/r/20230111150210.8246-1-ehakim@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Support dumping offload netlink attribute in macsec's device
attributes dump.
Change macsec_get_size to consider the offload attribute in
the calculations of the required room for dumping the device
netlink attributes.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for changing Macsec offload selection through the
netlink layer by implementing the relevant changes in
macsec_changelink.

Since the handling in macsec_changelink is similar to macsec_upd_offload,
update macsec_upd_offload to use a common helper function to avoid
duplication.

Example for setting offload for a macsec device:
    ip link set macsec0 type macsec offload mac
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

While reviewing dependencies in some Kconfig files, I noticed the redundant
dependency "depends on PCI && PCI_MSI". The config PCI_MSI has always,
since its introduction, been dependent on the config PCI. So, it is
sufficient to just depend on PCI_MSI, and know that the dependency on PCI
is implicitly implied.

Reduce the dependencies of some network driver configs.
No functional change and effective change of Kconfig dependendencies.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20230111125855.19020-1-lukas.bulwahn@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add mdio bus register for ngbe.
The internal phy and external phy need to be handled separately.
Add phy changed event detection.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230111111718.40745-1-mengyuanlou@net-swift.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Mika Westerberg says:

====================
net: thunderbolt: Add tracepoints

This series adds tracepoints and additional logging to the
Thunderbolt/USB4 networking driver. These are useful when debugging
possible issues.

Before that we move the driver into its own directory under drivers/net
so that we can add additional files without trashing the network drivers
main directory, and update the MAINTAINERS accordingly.

v1: https://lore.kernel.org/netdev/20230104081731.45928-1-mika.westerberg@linux.intel.com/
====================

Link: https://lore.kernel.org/r/20230111062633.1385-1-mika.westerberg@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

These are useful when debugging various performance issues.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

These can be useful when debugging possible issues around USB4NET
control packet exchange.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We will be adding tracepoints to the driver so instead of littering the
main network driver directory, move the driver into its own directory.
While there, rename the module to thunderbolt_net (with underscore) to
match with the thunderbolt_dma_test convention.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There are no more users of the obsolete interface
u64_stats_fetch_begin_irq() and u64_stats_fetch_retry_irq().

Remove the obsolete API.

[bigeasy: Split out the bits from a larger patch].
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20230110160738.974085-1-bigeasy@linutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/usb/r8152.c
  be53771c ("r8152: add vendor/device ID pair for Microsoft Devkit")
  ec51fbd1 ("r8152: add USB device driver for config selection")
https://lore.kernel.org/all/20230113113339.658c4723@canb.auug.org.au/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Paolo Abeni:
 "Including fixes from rxrpc.

  The rxrpc changes are noticeable large: to address a recent regression
  has been necessary completing the threaded refactor.

  Current release - regressions:

   - rxrpc:
       - only disconnect calls in the I/O thread
       - move client call connection to the I/O thread
       - fix incoming call setup race

   - eth: mlx5:
       - restore pkt rate policing support
       - fix memory leak on updating vport counters

  Previous releases - regressions:

   - gro: take care of DODGY packets

   - ipv6: deduct extension header length in rawv6_push_pending_frames

   - tipc: fix unexpected link reset due to discovery messages

  Previous releases - always broken:

   - sched: disallow noqueue for qdisc classes

   - eth: ice: fix potential memory leak in ice_gnss_tty_write()

   - eth: ixgbe: fix pci device refcount leak

   - eth: mlx5:
       - fix command stats access after free
       - fix macsec possible null dereference when updating MAC security
         entity (SecY)"

* tag 'net-6.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (64 commits)
  r8152: add vendor/device ID pair for Microsoft Devkit
  net: stmmac: add aux timestamps fifo clearance wait
  bnxt: make sure we return pages to the pool
  net: hns3: fix wrong use of rss size during VF rss config
  ipv6: raw: Deduct extension header length in rawv6_push_pending_frames
  net: lan966x: check for ptp to be enabled in lan966x_ptp_deinit()
  net: sched: disallow noqueue for qdisc classes
  iavf/iavf_main: actually log ->src mask when talking about it
  igc: Fix PPS delta between two synchronized end-points
  ixgbe: fix pci device refcount leak
  octeontx2-pf: Fix resource leakage in VF driver unbind
  selftests/net: l2_tos_ttl_inherit.sh: Ensure environment cleanup on failure.
  selftests/net: l2_tos_ttl_inherit.sh: Run tests in their own netns.
  selftests/net: l2_tos_ttl_inherit.sh: Set IPv6 addresses with "nodad".
  net/mlx5e: Fix macsec possible null dereference when updating MAC security entity (SecY)
  net/mlx5e: Fix macsec ssci attribute handling in offload path
  net/mlx5: E-switch, Coverity: overlapping copy
  net/mlx5e: Don't support encap rules with gbp option
  net/mlx5: Fix ptp max frequency adjustment range
  net/mlx5e: Fix memory leak on updating vport counters
  ...

Pull s390 fixes from Heiko Carstens:

 - Add various missing READ_ONCE() to cmpxchg() loops prevent the
   compiler from potentially generating incorrect code. This includes a
   rather large change to the s390 specific hardware sampling code and
   its current use of cmpxchg_double().

   Do the fix now to get it out of the way of Peter Zijlstra's
   cmpxchg128() work, and have something that can be backported. The
   added new code includes a private 128 bit cmpxchg variant which will
   be removed again after Peter's rework is available. Also note that
   this 128 bit cmpxchg variant is used to implement 128 bit
   READ_ONCE(), while strictly speaking it wouldn't be necessary, and
   _READ_ONCE() should also be sufficient; even though it isn't obvious
   for all converted locations that this is the case. Therefore use this
   implementation for for the sake of clarity and consistency for now.

 - Fix ipl report address handling to avoid kdump failures/hangs.

 - Fix misuse of #(el)if in kernel decompressor.

 - Define RUNTIME_DISCARD_EXIT to fix link error with GNU ld < 2.36,
   caused by the recently changed discard behaviour.

 - Make sure _edata and _end symbols are always page aligned.

 - The current header guard DEBUG_H in one of the s390 specific header
   files is too generic and conflicts with the ath9k wireless driver.
   Add an _ASM_S390_ prefix to the guard to make it unique.

 - Update defconfigs.

* tag 's390-6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: update defconfigs
  KVM: s390: interrupt: use READ_ONCE() before cmpxchg()
  s390/percpu: add READ_ONCE() to arch_this_cpu_to_op_simple()
  s390/cpum_sf: add READ_ONCE() semantics to compare and swap loops
  s390/kexec: fix ipl report address for kdump
  s390: fix -Wundef warning for CONFIG_KERNEL_ZSTD
  s390: define RUNTIME_DISCARD_EXIT to fix link error with GNU ld < 2.36
  s390: expicitly align _edata and _end symbols on page boundary
  s390/debug: add _ASM_S390_ prefix to header guard

Pull xen fixes from Juergen Gross:

 - two cleanup patches

 - a fix of a memory leak in the Xen pvfront driver

 - a fix of a locking issue in the Xen hypervisor console driver

* tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/pvcalls: free active map buffer on pvcalls_front_free_map
  hvc/xen: lock console list traversal
  x86/xen: Remove the unused function p2m_index()
  xen: make remove callback of xen driver void returned

Pull timer doc fixes from Ingo Molnar:

 - Fix various DocBook formatting errors in kernel/time/ that generated
   (justified) warnings during a kernel-doc build.

* tag 'timers-urgent-2023-01-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: Fix various kernel-doc problems

Pull perf events hw enablement from Ingo Molnar:

 - More hardware-enablement for Intel Meteor Lake & Emerald Rapid
   systems: pure model ID enumeration additions that do not affect other
   systems.

* tag 'perf-urgent-2023-01-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/uncore: Add Emerald Rapids
  perf/x86/msr: Add Emerald Rapids
  perf/x86/msr: Add Meteor Lake support
  perf/x86/cstate: Add Meteor Lake support

Pull scheduler fixes from Ingo Molnar:

 - Fix scheduler frequency invariance bug related to overly long
   tickless periods triggering an integer overflow and disabling the
   feature.

 - Fix use-after-free bug in dup_user_cpus_ptr().

 - Fix do_set_cpus_allowed() deadlock scenarios related to calling
   kfree() with the pi_lock held. NOTE: the rcu_free() is the 'lazy'
   solution here - we looked at patches to free the structure after the
   pi_lock got dropped, but that looked quite a bit messier - and none
   of this is truly performance critical. We can revisit this if it's
   too lazy of a solution ...

* tag 'sched-urgent-2023-01-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Use kfree_rcu() in do_set_cpus_allowed()
  sched/core: Fix use-after-free bug in dup_user_cpus_ptr()
  sched/core: Fix arch_scale_freq_tick() on tickless systems

Pull objtool fix from Ingo Molnar:

 - Fix objtool to be more permissive with hand-written assembly that
   uses non-function symbols in executable sections.

* tag 'core-urgent-2023-01-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Tolerate STT_NOTYPE symbols at end of section

Merge tag 'urgent-nolibc.2023.01.09a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu

Pull nolibc fixes from Paul McKenney:

 - The fd_set structure was incorrectly defined as arrays of u32 instead
   of long, which breaks BE64. Fix courtesy of Sven Schnelle.

 - S_ISxxx macros were incorrectly testing the bits after applying them
   instead of bitwise ANDing S_FMT with the value. Fix from Warner Losh.

 - The mips code was randomly broken due to an unprotected "noreorder"
   directive in the _start code that could prevent the assembler from
   filling delayed slots. This in turn resulted in random other
   instructions being placed into those slots. Fix courtesy of Willy
   Tarreau.

 - The current nolibc header layout refrains from including files that
   are not explicitly included by the code using nolibc. Unfortunately,
   this causes build failures when such files contain definitions that
   are used (for example) by libgcc. Example definitions include raise()
   and memset(), which are called by some architectures, but only at
   certain optimization levels. Fix courtesy of Willy Tarreau.

 - gcc 11.3 in ARM thumb2 mode at -O2 recognized a memset() construction
   inside the memset() definition. The compiler replaced this
   construction with a call to... memset(). Userland cannot be forced to
   build with -ffreestanding, so an empty asm() statement was introduced
   into the loop the loop in order to prevent the compiler from making
   this unproductive transformation. Fix courtesy of Willy Tarreau.

 - Most of the O_* macros were wrong on RISCV because their octal values
   were coded as hexadecimal. This resulted in the getdents64() selftest
   failing. Fix courtesy of Willy Tarreau.

This was tested on x86_64, i386, armv5, armv7, thumb1, thumb2, mips and
riscv, all at -O0, -Os and -O3.

* tag 'urgent-nolibc.2023.01.09a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
  tools/nolibc: fix the O_* fcntl/open macro definitions for riscv
  tools/nolibc: prevent gcc from making memset() loop over itself
  tools/nolibc: fix missing includes causing build issues at -O0
  tools/nolibc: restore mips branch ordering in the _start block
  tools/nolibc: Fix S_ISxxx macros
  nolibc: fix fd_set type

The Microsoft Devkit 2023 is a an ARM64 based machine featuring a
Realtek 8153 USB3.0-to-GBit Ethernet adapter. As in their other
machines, Microsoft uses a custom USB device ID.

Add the respective ID values to the driver. This makes Ethernet work on
the MS Devkit device. The chip has been visually confirmed to be a
RTL8153.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20230111133228.190801-1-andre.przywara@arm.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Pull spi fixes from Mark Brown:

 - Fixes for long standing issues with accesses to spidev->spi during
   teardown in the spidev userspace driver.

 - Rename the newly added spi-cs-setup-ns DT property to be more in line
   with our other delay properties before it becomes ABI.

 - A few driver specific fixes.

* tag 'spi-fix-v6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: spidev: remove debug messages that access spidev->spi without locking
  spi: spidev: fix a race condition when accessing spidev->spi
  spi: Rename spi-cs-setup-ns property to spi-cs-setup-delay-ns
  spi: dt-bindings: Rename spi-cs-setup-ns to spi-cs-setup-delay-ns
  spi: cadence: Fix busy cycles calculation
  spi: mediatek: Enable irq before the spi registration

Merge tag 'regulator-fix-v6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "A couple of small driver specific fixes, one of which I queued for 6.1
  but didn't actually send out so has had *plenty* of testing in -next"

* tag 'regulator-fix-v6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: qcom-rpmh: PM8550 ldo11 regulator is an nldo
  regulator: da9211: Use irq handler when ready

Pull MTD fixes from Miquel Raynal:

 - cfi: Allow building spi-intel standalone to avoid build issues

 - parsers: scpart: Fix __udivdi3 undefined on mips

 - parsers: tplink_safeloader: Fix potential memory leak during parsing

 - Update email of Tudor Ambarus

* tag 'mtd/fixes-for-6.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
  MAINTAINERS: Update email of Tudor Ambarus
  mtd: cfi: allow building spi-intel standalone
  mtd: parsers: scpart: fix __udivdi3 undefined on mips
  mtd: parsers: Fix potential memory leak in mtd_parser_tplink_safeloader_parse()